Occurrence of polycyclic musks in wastewater and receiving water bodies and fate during wastewater treatment

The occurrence of cashmerane (DPMI), celestolide, phantolide, traesolide (ATII), galaxolide (HHCB) and tonalide (AHTN) in sewage and surface waters and their fate during wastewater treatment and anaerobic sludge digestion is investigated. AHTN and HHCB are the most important representatives and influent concentrations of 0.41-1.8 and 0.9-13 μg L⁻¹ are observed. DPMI is detected in influent and effluent samples but in notably lower concentrations than AHTN and HHCB. Major sources of polycyclic musks are households, whereas industrial emitters seem to be of minor importance. This conclusion is supported by the analysis of selected industrial wastewaters (metal, textile and paper industry). Specific emissions of 0.36 ± 0.19 and 1.6 ± 1.0 mg cap⁻¹ d⁻¹ for AHTN and HHCB are calculated. Overall removal efficiencies between approx 50% and more than 95% are observed during biological wastewater treatment and removal with the excess sludge is the major removal pathway. Log K_D values of 3.73-4.3 for AHTN, 3.87-4.34 for HHCB and 2.42-3.22 for DPMI are observed in secondary sludge. During sludge digestion no or only slight removal occurred. Mean polycyclic musk concentrations in digested sludge amounted to 1.9 ± 0.9 (AHTN), 14.2 ± 5.8 (HHCB), 0.8 ± 0.4 (ATII) and 0.2 ± 0.09 (DPMI) mg kg⁻¹ dry matter. In the receiving water systems a comparable distribution as during wastewater treatment is observed. AHTN, HHCB and DPMI are detected in surface waters (ND (not detected) - < 0.04, ND - 0.32 and ND - 0.02 μg L⁻¹) as well as AHTN and HHCB in sediments (ND - 20, ND - 120 μg kg⁻¹). For HHCB an apparent K_OC value of 4.1-4.4 is calculated for sediments. Major source for polycyclic musks in surface waters are discharges from wastewater treatment plants. For HHCB and DPMI 100% of the load observed in the sampled surface waters derive from discharges of treated wastewater.     

Measuring the fractal dimension of diesel soot agglomerates by fractional Brownian motion processor

This work explores the application of fractional Brownian motion (FBM) analysis to SEM micrographs of soot aggregates exhausted by a model dynamometer. By directly quantifying the surface texture of fractal-like aggregates to extract their Hurst coefficients (H), the FBM analysis was successful in parameterizing fractal dimension (D_f) values, from which the relative aggregate structure variables could easily be determined. For two microscopic magnification scales (×50,000 and ×10⁵), the soot aggregate D_f fell in the range of 1.6–1.7. The experimental results closely agreed with the main conclusions derived from previous studies. An alternative approach is to clarify the impact of image properties on D_f measurements due to digital image processing and data recording. A twofold change in SEM magnification size gave rise to a 7% deviation, and scaling up from the original image increased the discrepancy compared to miniaturization. In conclusion, texture characterization is useful for estimating the fractal properties of most chain-like or cluster soot aggregates.     

Levels and distribution of Dechlorane Plus in coastal sediments of the Yellow Sea, North China

Dechlorane Plus (DP) has been determined in surface sediments from three Chinese coastal bays, e.g. Jiaozhou, Sishili and Taozi Bay in North China. DP concentrations ranged from <1.2 to 187 pg g⁻¹ dry weight (dw) (mean: 24.7 pg g⁻¹ dw) in Jiaozhou Bay, <1.2 to 135 pg g⁻¹ dw (mean 69.9 pg g⁻¹ dw) in Sishili Bay and <1.2 to 66.7 pg g⁻¹ dw (mean: 40.4 pg g⁻¹ dw) in Taozi Bay, respectively. Additionally, two dechlorinated species were quantified, which accounted for 0.6-5.1% of the ∑DP concentration.The f_syn values (syn-isomer/(syn- + anti-isomer)) in sediments from Jiaozhou Bay (mean 0.29) were close to the technical DP mixture (0.2-0.4), probably indicating local inputs of DP. In contrast, sediments in Sishili and Taozi Bay showed much lower f_syn values (mean 0.16). During transportation the DP isomers are subject to stereo selective degradation which partly resulted in the relative enrichment of anti-DP in coastal sediments.     

Characterization of mercury species in brown and white rice (Oryza sativa L.) grown in water-saving paddies

In China, total Hg (Hg_T) and methylmercury (MeHg) were quantified in rice grain grown in three sites using water-saving rice cultivation methods, and in one Hg-contaminated site, where rice was grown under flooded conditions. Polished white rice concentrations of Hg_T (water-saving: 3.3 ± 1.6 ng/g; flooded: 110 ± 9.2 ng/g) and MeHg (water-saving 1.3 ± 0.56 ng/g; flooded: 12 ± 2.4 ng/g) were positively correlated with root-soil Hg_T and MeHg contents (Hg_T: r² = 0.97, MeHg: r² = 0.87, p < 0.05 for both), which suggested a portion of Hg species in rice grain was derived from the soil, and translocation of Hg species from soil to rice grain was independent of irrigation practices and Hg levels, although other factors may be important. Concentrations of Hg_T and other trace elements were significantly higher in unmilled brown rice (p < 0.05), while MeHg content was similar (p > 0.20), indicating MeHg infiltrated the endosperm (i.e., white rice) more efficiently than inorganic Hg(II).     

Sorption of chlorinated solvents and degradation products on natural clayey tills

The sorption of chlorinated solvents and degradation products on seven natural clayey till samples from three contaminated sites was investigated by laboratory batch experiments in order to obtain reliable sorption coefficients (K_d values). The sorption isotherms for all compounds were nearly linear, but fitted by Freundlich isotherms slightly better over the entire concentration range. For chloroethylenes, tetrachloroethylene (PCE) was most strongly sorbed to the clayey till samples (K_d = 0.84-2.45 L kg⁻¹), followed by trichloroethylene (TCE, K_d = 0.62-0.96 L kg⁻¹), cis-dichloroethylene (cis-DCE, K_d = 0.17-0.82 L kg⁻¹) and vinyl chloride (VC, K_d = 0.12-0.36 L kg⁻¹). For chloroethanes, 1,1,1-trichloroethane (1,1,1-TCA) was most strongly sorbed (K_d = 0.2-0.45 L kg⁻¹), followed by 1,1-dichloroethane (1,1-DCA, K_d = 0.16-0.24 L kg⁻¹) and chloroethane (CA, K_d = 0.12-0.18 L kg⁻¹). This is consistent with the order of hydrophobicity of the compounds. The octanol-water coefficient (log K_ow) correlated slightly better with log K_d values than log K_oc values indicating that the K_d values may be independent of the actual organic carbon content (f_oc). The estimated log K_oc or log K_d for chlorinated solvents and degradation products determined by regression of data in this study were significantly higher than values determined by previously published empirical relationships. The site specific K_d values as well as the new empirical relationship compared well with calculations on water and soil core concentration for cis-DCE and VC from the Rugårdsvej site. In conclusion, this study with a wide range of chlorinated ethenes and ethanes - in line with previous studies on PCE and TCE - suggest that sorption in clayey tills could be higher than typically expected.     

Species- and tissue-specific accumulation of Dechlorane Plus in three terrestrial passerine bird species from the Pearl River Delta, South China

Little data is available on the bioaccumulation of Dechlorane Plus (DP) in terrestrial organisms. Three terrestrial passerine bird species, light-vented bulbul, long-tailed shrike, and oriental magpie-robin, were collected from rural and urban sites in the Pearl River Delta to analyze for the presence of DP and its dechlorinated products in muscle and liver tissues. The relationships between trophic level and concentration and isomeric composition of DP in birds were also investigated based on stable nitrogen isotope analysis. DP levels had a wide range from 3.9 to 930 ng g⁻¹ lipid weight (lw) in muscle and from 7.0 to 1300 ng g⁻¹ lw in liver. Anti-Cl₁₁-DP and syn-Cl₁₁-DP, two dechlorinated products of DP, were also detected in bird samples with concentrations ranged between not detected (nd)-41 and nd-7.6 ng g⁻¹ lw, respectively. DP preferentially accumulated in liver rather than in muscle for all three bird species. Birds had significantly higher concentrations of DP in urban sites than in rural sites (mean, 300 vs 73 ng g⁻¹ lw). The fractions of anti-DP (f_anti) were higher in birds collected in rural sites than in urban sites. Significant positive correlation between DP levels and δ¹⁵N values but significant negative correlation between f_anti and δ¹⁵N values were found for birds in both urban and rural sites, indicating that trophic level of birds play an important role in determining DP level and isomeric profile.     

Compound specific carbon and hydrogen stable isotope analyses of volatile organic compounds in various emissions of combustion processes

This study presents carbon (δ¹³C) and hydrogen (δD) isotope values of volatile organic compounds (VOCs) in various emission sources using thermal desorption-gas chromatography-isotope ratio mass spectrometry (TD-GC-irMS). The investigated VOCs ranged from C6 to C10. Samples were taken from (i) car exhaust emissions as well as from plant combustion experiments of (ii) various C3 and (iii) various C4 plants. We found significant differences in δ values of analysed VOCs between these sources, e.g. δ¹³C of benzene ranged between (i) −21.7 ± 0.2‰, (ii) −27.6 ± 1.6‰ and (iii) −16.3 ± 2.2‰, respectively and δD of benzene ranged between (i) −73 ± 13‰, (ii) −111 ± 10‰ and (iii) −70 ± 24‰, respectively. Results of VOCs present in investigated emission sources were compared to values from the literature (aluminium refinery emission). All source groups could be clearly distinguished using the dual approach of δ¹³C and δD analysis. The results of this study indicate that the correlation of compound specific carbon and hydrogen isotope analysis provides the potential for future research to trace the fate and to determine the origin of VOCs in the atmosphere using thermal desorption compound specific isotope analysis.     

Antifungal efficacy of some natural phenolic compounds against significant pathogenic and toxinogenic filamentous fungi

In terms of food safety, species of the Fusarium, Aspergillus and Penicillium genera are considered the most significant because they produce the great majority of known mycotoxins. Developing resistance against commonly used fungicides have become a critical problem in area such as agriculture, the storage and production of food and even in human medicines. The need for research and development of new alternative antifungal treatment based on natural antifungal substances is obvious. Here, the antifungal efficacy of 21 phenolic components of essential oils and plant substances were tested against these filamentous fungi with respect to their different molecular structures. Minimum inhibitory concentration values MIC₅₀ and MIC₁₀₀ were successfully estimated for 15 substances by means of probit analysis. Thymol and carvacrol were evaluated as the most effective. The MIC₅₀ values for thymol ranged from 30 to 52 μg mL⁻¹. The MIC₁₀₀ values for thymol ranged from 76 to 255 μg mL⁻¹, respectively. For carvacrol, the MIC₅₀ values ranged from 37 to 76 μg mL⁻¹, and the MIC₁₀₀ ranged from 131 to 262 μg mL⁻¹. The results also revealed differences in the efficacy of phenols depending on molecular structures and different inter-species sensitivity.     

Photocatalytic degradation with immobilised TiO(2) of three selected neonicotinoid insecticides: imidacloprid, thiamethoxam and clothianidin

This research focused on photocatalytic degradation of imidacloprid, thiamethoxam and clothianidin employing a tailor-made photoreactor with six polychromatic fluorescent UVA (broad maximum at 355 nm) lamps and immobilised titanium dioxide (TiO₂) on glass slides. The disappearance was followed by high pressure liquid chromatography (HPLC-DAD) analyses, wherein the efficiency of mineralization was monitored by measurements of total organic carbon (TOC). Within 2 h of photocatalysis, all three neonicotinoids were degraded following first order kinetics with rate constants k = 0.035 ± 0.001 min⁻¹ for imidacloprid, k = 0.019 ± 0.001 min⁻¹ for thiamethoxam and k = 0.021 ± 0.000 min⁻¹ for clothianidin. However, the rate of mineralization was low, i.e. 19.1 ± 0.2% for imidacloprid, 14.4 ± 2.9% for thiamethoxam and 14.1 ± 0.4% for clothianidin. This indicates that several transformation products were formed instead. Some of them were observed within HPLC-DAD analyses and structures were proposed according to the liquid chromatography-electro spray ionization tandem mass spectrometry analyses (LC-ESI-MS/MS). The formation of clothianidin, as thiamethoxam transformation product, was reported for the first time.     

Dry deposition and soil-air gas exchange of polychlorinated biphenyls (PCBs) in an industrial area

Ambient air and dry deposition, and soil samples were collected at the Aliaga industrial site in Izmir, Turkey. Atmospheric total (particle + gas) ∑₄₁-PCB concentrations were higher in summer (3370 ± 1617 pg m⁻³, average + SD) than in winter (1164 ± 618 pg m⁻³), probably due to increased volatilization with temperature. Average particulate ∑₄₁-PCBs dry deposition fluxes were 349 ± 183 and 469 ± 328 ng m⁻² day⁻¹ in summer and winter, respectively. Overall average particulate deposition velocity was 5.5 ± 3.5 cm s⁻¹. The spatial distribution of ∑₄₁-PCB soil concentrations (n = 48) showed that the iron-steel plants, ship dismantling facilities, refinery and petrochemicals complex are the major sources in the area. Calculated air-soil exchange fluxes indicated that the contaminated soil is a secondary source to the atmosphere for lighter PCBs and as a sink for heavier ones. Comparable magnitude of gas exchange and dry particle deposition fluxes indicated that both mechanisms are equally important for PCB movement between air and soil in Aliaga.     

Development of a combined isotopic and mass-balance approach to determine dissolved organic carbon sources in eutrophic reservoirs

A combined mass-balance and stable isotope approach was set up to identify and quantify dissolved organic carbon (DOC) sources in a DOC-rich (9 mg L⁻¹) eutrophic reservoir located in Western France and used for drinking water supply (so-called Rophemel reservoir). The mass-balance approach consisted in measuring the flux of allochthonous DOC on a daily basis, and in comparing it with the effective (measured) DOC concentration of the reservoir. The isotopic approach consisted, for its part, in measuring the carbon isotope ratios (δ¹³C values) of both allochthonous and autochthonous DOC sources, and comparing these values with the δ¹³C values of the reservoir DOC. Results from both approaches were consistent pointing out for a DOC of 100% allochthonous origin. In particular, the δ¹³C values of the DOC recovered in the reservoir (−28.5 ± 0.2‰; n = 22) during the algal bloom season (May-September) showed no trace of an autochthonous contribution (δ¹³C in algae = −30.1 ± 0.3‰; n = 2) being indistinguishable from the δ¹³C values of allochthonous DOC from inflowing rivers (−28.6 ± 0.1‰; n = 8). These results demonstrate that eutrophication is not responsible for the high DOC concentrations observed in the Rophemel reservoir and that limiting eutrophication of this reservoir will not reduce the potential formation of disinfection by-products during water treatment. The methodology developed in this study based on a complementary isotopic and mass-balance approach provides a powerful tool, suitable to identify and quantify DOC sources in eutrophic, DOC-contaminated reservoirs.     

Using native epiphytic ferns to estimate the atmospheric mercury levels in a small-scale gold mining area of West Java, Indonesia

Mercury pollution is caused by artisanal and small-scale gold mining (ASGM) operations along the Cikaniki River (West Java, Indonesia). The atmosphere is one of the primary media through which mercury can disperse. In this study, atmospheric mercury levels are estimated using the native epiphytic fern Asplenium nidus complex (A. nidus) as a biomonitor; these estimates shed light on the atmospheric dispersion of mercury released during mining.Samples were collected from 8 sites along the Cikaniki Basin during September-November, 2008 and September-November, 2009.The A. nidus fronds that were attached to tree trunks 1-3 m above the ground were collected and measured for total mercury concentration using cold vapor atomic absorption spectrometry (CVAAS) after acid-digestion. The atmospheric mercury was collected using porous gold collectors, and the concentrations were determined using double-amalgam CVAAS.The highest atmospheric mercury concentration, 1.8 × 10³ ± 1.6 × 10³ ng m⁻³, was observed at the mining hot spot, and the lowest concentration of mercury, 5.6 ± 2.0 ng m⁻³, was observed at the remote site from the Cikaniki River in 2009. The mercury concentrations in A. nidus were higher at the mining village (5.4 × 10³ ± 1.6 × 10³ ng g⁻¹) than at the remote site (70 ± 30 ng g⁻¹). The distribution of mercury in A. nidus was similar to that in the atmosphere; a significant correlation was observed between the mercury concentrations in the air and in A. nidus (r = 0.895, P < 0.001, n = 14). The mercury levels in the atmosphere can be estimated from the mercury concentration in A. nidus using a regression equation: log (Hg_A.nidu/ng g⁻¹) = 0.740 log (Hg_Air/ng m⁻³) − 1.324.     

Adsorption and breakdown of penicillin antibiotic in the presence of titanium oxide nanoparticles in water

The fate and transport of antibiotics in natural water systems is controlled in part by interactions with nanometer (10⁻⁹ m) metal oxide particles. Experiments were performed by mixing solutions of ampicillin (AMP), a common, penicillin-class human and veterinary antibiotic, with 25 nm-TiO₂ (anatase) nanoparticles at different pH conditions. Both sorption and degradation of AMP were observed in the AMP-nanoparticle solutions. For AMP concentrations from ∼3 μM to 2.9 mM the overall AMP removal from solution can be described by linear isotherms with removal coefficients (K_r) of 3028 (±267) L kg⁻¹ at pH 2, 11,533 (±823) L kg⁻¹ at pH 4, 12,712 (±672) L kg⁻¹ at pH 6, and 1941 (±342) L kg⁻¹ at pH 8. Mass spectral analysis of AMP solutions after removal of the solid nanoparticles yielded ions that indicate the presence of peniclloic acid, penilloic acid and related de-ammoniated by-products as possible compounds resulting from the degradation of AMP at the TiO₂ surface.     

Sorption comparison between phenanthrene and its degradation intermediates, 9,10-phenanthrenequinone and 9-phenanthrol in soils/sediments

The degradation intermediates of phenanthrene (PHE) may have increased health risks to organisms than PHE. Therefore, environmental fate and risk assessment studies should take into considerations of PHE degradation products. This study compared the sorption properties of PHE and its degradation intermediates, 9,10-phenanthrenequinone (PQN) and 9-phenanthrol (PTR) in soils, sediments and soil components. A relationship between organic carbon content (f_OC) and single-point sorption coefficient (log K_d) was observed for all three chemicals in 10 soils/sediments. The large intercept in the log f_OC − log K_d regression for PTR indicated that inorganic fractions control PTR sorption in soils/sediments. No relationship between specific surface area and K_d was observed. This result indicated that determination of surface area based on gas sorption could not identify surface properties for PHE, PQN, and PTR sorption and thus provide limit information on sorption mechanisms. The high sorption and strong nonlinearity (low n values) of PTR in comparison to PHE suggested that the mobility of PTR could be lower than PHE. Increased mobility of PQN compared with PHE may be expected in soils/sediments because of PQN lower sorption. The varied sorption properties of the three chemicals suggested that their environmental risks should be assessed differently.     

Salting-out phenomenon and 1-octanol/water partition coefficient of metalaxyl pesticide

In this paper, we present the effect of inorganic cations such as Na⁺, K⁺, Ca²⁺, Mg²⁺ on the salting-out phenomenon of metalaxyl from pure water to aqueous salt solutions. Moreover the 1-octanol/water partition coefficient in pure water is presented. To accomplish this, aqueous solubility of metalaxyl was determined in pure water, in different salt solution (NaCl, KCl, CaCl₂ and MgCl₂), and at different concentration level ranging from 0.01 to 1.5 M. The 1-octanol/water partition coefficient was determined using the static shake-flask method. Solubility was determined using dynamic saturation method for pure water in the range of 298.15-325.15 K and at 298.15 K for different salt solutions. The solubility value in pure water for studied interval was found constant (m = 3.118 × 10⁻² mol kg⁻¹).Solubility values were used to calculate the standard molar Gibbs free energy of dissolution (Δ_solG°) and transfer (Δ_trG°) at 298.15 K. The values of Δ_trG° from pure to all studied aqueous salt solutions did not exceed 2 kJ mol⁻¹, the value of Δ_solG° of dissolution is 18.5 ±0.72 kJ mol⁻¹. The 1-octanol/water partition coefficient in pure water log K_o/w is equal to 1.69. The obtained results confirm the classification of the neutral metalaxyl as a slightly hydrophobic molecule.     

Concentrations and sources of Dechlorane Plus in sewage sludge

Sewage sludge from 31 urban Spanish wastewater treatment plants (WWTP) was analyzed for the emerging halogenated flame retardant Dechlorane Plus (DP). Concentrations of the two major isomers in the technical mixture, syn and anti, ranged between 0.903-19.2 and 1.55-75.1 ng g⁻¹ dry weight, respectively. Overall, concentrations of DP were lower than those of polybrominated diphenyl ethers (PBDEs) (9.10-995 ng g⁻¹ dry weight) and this is likely related to the higher usage of brominated flame retardants. The average ratio of the syn isomer to total DP (f_syn) was 0.28 ± 0.05, which is similar to that of the commercial mixture. Comparing different wastewater treatment methods, we found lower concentrations in those using biological nitrogen and phosphorous elimination, suggesting that DP is susceptible to microbial degradation and that anti-DP is more so, given the enrichment of syn-DP in the sewage sludge. Principal components analysis revealed significant positive correlation (r = 0.619, p < 0.05) between total DP concentrations with the contribution of industrial input to waste streams. This implies release of DP is related to industrial activity, likely stemming from the use of the technical product during manufacture of consumer goods. However, use and disposal of products containing DP could not be dismissed. According to our knowledge, this is the first report on DP in WWTP sludge.     

Partitioning of perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS) and perfluorooctane sulfonamide (PFOSA) between water and sediment

Laboratory partitioning experiments were conducted to elucidate the sorption behaviour and partitioning of perfluoroalkyl compounds (PFCs). Three different sediment types were used and separately spiked with perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS) and perfluorooctane sulfonamide (PFOSA) at low environmentally realistic concentrations. PFOA, PFOS and PFOSA were mainly distributed in the dissolved phase at low suspended solid concentrations, indicating their long-range transport potential in the marine environment. In all cases, the equilibrium isotherms were linear and the organic carbon normalised partition coefficients (K_OC) decreased in the following order: PFOSA (log K_OC = 4.1 ± 0.35 cm³ g⁻¹) > PFOS (3.7 ± 0.56 cm³ g⁻¹) > PFOA (2.4 ± 0.12 cm³ g⁻¹). The level of organic content had a significant influence on the partitioning. For the sediment with negligible organic content the density of the sediment became the most important factor influencing the partitioning. Ultimately, data on the partitioning of PFCs between aqueous media and suspended solids are essential for modelling their transport and environmental fate.     

Partitioning behaviour of perfluorinated alkyl contaminants between water, sediment and fish in the Orge River (nearby Paris, France)

This paper reports on the partitioning behaviour of 15 perfluorinated compounds (PFCs), including C₄-C₁₀ sulfonates and C₅-C₁₄ carboxylic acids, between water, sediment and fish (European chub, Leuciscus cephalus) in the Orge River (nearby Paris). Total PFC levels were 73.0 ± 3.0 ng L⁻¹ in water and 8.4 ± 0.5 ng g⁻¹ in sediment. They were in the range 43.1-4997.2 ng g⁻¹ in fish, in which PFC tissue distribution followed the order plasma > liver > gills > gonads > muscle. Sediment-water distribution coefficients (log K_d) and bioaccumulation factors (log BAF) were in the range 0.8-4.3 and 0.9-6.7, respectively. Both distribution coefficients positively correlated with perfluoroalkyl chain length. Field-based biota-sediment accumulation factors (BSAFs) are also reported, for the first time for PFCs other than perfluorooctane sulfonate. log BSAF ranged between −1.3 and 1.5 and was negatively correlated with the perfluoroalkyl chain length in the case of carboxylic acids.     

Photolytic and photocatalytic degradation of 6-chloronicotinic acid

This work describes for the first time the photolytic and photocatalytic degradation of 6-chloronicotinic acid (6CNA) in double deionised water, which is a degradation product of neonicotinoid insecticides imidacloprid and acetamiprid, and it is known to appear in different environmental matrices. Photolytic experiments were performed with three UVA (ultraviolet A) polychromatic fluorescent lamps with broad maximum at 355 nm, while photocatalytic experiments were performed using immobilised titanium dioxide (TiO₂) on six glass slides in the spinning basket inside a photocatalytic quartz cell under similar irradiation conditions. Photolytic degradation revealed no change in concentration of 6CNA within 120 min of irradiation, while the photocatalytic degradation within 120 min, obeyed first-order kinetics. The observed disappearance rate constant was k = 0.011 ± 0.001 min⁻¹ and t_1/2 was 63.1 ± 5.5 min. Mineralisation rate was estimated through total organic carbon (TOC) and measurements revealed no carbon removal in case of photolysis after 120 min of exposure. However in photocatalytic experiments 46 ± 7% mineralisation was achieved within 120 min of irradiation. Nevertheless, the removal of total nitrogen (TN) was not observed across all experiments. Ion chromatographic analyses indicated transformation of chlorine atoms to chloride and increase of nitrate(V) ions only via photocatalytic experiments. Efficiency of selected advanced oxidation process (AOP) was investigated through toxicity assessment with Vibrio fischeri luminescent bacteria and revealed higher adverse effects of treated samples on bacteria following photocatalytic degradation in spite of the fact that higher mineralisation was achieved. New hydroxylated product generated in photocatalytic experiments with TiO₂, was confirmed with liquid chromatography-electro spray ionisation mass spectrometry (LC-ESI-MS/MS) analyses, gas chromatography-mass spectrometry (GC-MS) and nuclear magnetic resonance spectroscopy (¹H NMR).