Catalytic CO2 gasification of rubber seed shell-derived hydrochar: reactivity and kinetic studies

In this study, hydrothermal carbonization (HTC) of a biomass was used as a means to improve the physicochemical properties of rubber seed shell (RSS) and enhance its reactivity in the char-CO₂ gasification reaction, known as the Boudouard reaction (C + CO₂ ? 2CO). Hydrochar samples were developed by hydrothermal treatment of RSS, without separating the solid residue from the liquid product, at 433, 473, 513, and 553 K under autogenous pressure. The CO₂ gasification reactivity of the developed hydrochars was then investigated at different heating rates (5, 10, 20, and 30 K/min) by the non-isothermal thermogravimetric method. The hydrochars revealed higher reactivity and improved gasification characteristics compared to the untreated biomass, while the hydrochar which was filtered from the liquid slurry showed lower reactivity compared to the untreated biomass. This was due to the chemical and structural evolutions of the biomass during hydrothermal treatment as indicated by various analyses. The gasification reactivity of the hydrochar was substantially enhanced by introduction of a catalyst (NaNO₃) during HTC. Kinetic analysis of the char-CO₂ gasification reaction was carried out by applying Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), and Starink isoconversional methods, and thermodynamic parameters were also determined. The activation energy of the Na-loaded RSS hydrochar in CO₂ gasification (120–154 kJ/mol) was considerably lower than that of the untreated biomass (153–172 kJ/mol). Thermodynamic studies also confirmed the promoting effect of hydrothermal treatment and catalyst impregnation on enhancement of reactivity of the virgin biomass and reduction of gasification temperature.

     

Persistence of C-labeled atrazine and its residues in a field lysimeter soil after 22 years

Twenty-two years after the last application of ring-¹⁴C-labeled atrazine at customary rate (1.7 kg ha⁻¹) on an agriculturally used outdoor lysimeter, atrazine is still detectable by means of accelerated solvent extraction and LC-MS/MS analysis. Extractions of the 0-10 cm soil layer yielded 60% of the residual ¹⁴C-activity. The extracts contained atrazine (1.0 μg kg⁻¹) and 2-hydroxy-atrazine (42.5 μg kg⁻¹). Extractions of the material of the lowest layer 55-60 cm consisting of fine gravel yielded 93% of residual ¹⁴C-activity, of which 3.4 μg kg⁻¹ was detected as atrazine and 17.7 μg kg⁻¹ was 2-hydroxy-atrazine. The detection of atrazine in the lowest layer was of almost four times higher mass than in the upper soil layer. These findings highlight the fact that atrazine is unexpectedly persistent in soil. The overall persistence of atrazine in the environment might represent a potential risk for successive groundwater contamination by leaching even after 22 years of environmental exposure.     

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement

The effects of the herbicide atrazine on the gill of the freshwater fish Prochilodus lineatus were evaluated after exposure of fish to 2, 10 and 25 μg L⁻¹ atrazine during 48 h (acute exposure) and 14 d (subchronic exposure). Ions and osmolality were measured in plasma and gill samples were taken to determine the Na⁺/K⁺-ATPase (NKA) and carbonic anhydrase (CA) activities and for morphological analysis. Plasma osmolality and Na⁺ and Cl⁻ ions changed depending on atrazine concentration, but atrazine exposure had no effect on the Na⁺/Cl⁻ ratio. NKA activity did not change after atrazine exposure, but CA activity decreased in fish exposed to 25 μg L⁻¹ for 14 d. Gill MRC density decreased after acute exposure but did not change in fish exposed to the subchronic treatment. The MRC density at the epithelial surface increased in fish exposed to 25 μg L⁻¹, and the MRC fractional area (MRCFA) increased in fish exposed to 10 μg L⁻¹. The changes in MRCs provide evidence of morphological adjustments to maintain ionic homeostasis in spite of the inhibition of CA activity at the highest atrazine concentration.     

Effect of fluctuating soil humidity on in situ bioavailability and degradation of atrazine

This study elucidates the effect of fluctuating soil moisture on the co-metabolic degradation of atrazine (6-chloro-N²-ethyl-N⁴-isopropyl-1,3,5-triazine-2,4-diamine) in soil. Degradation experiments with ¹⁴C-ring-labelled atrazine were carried out at (i) constant (CH) and (ii) fluctuating soil humidity (FH). Temperature was kept constant in all experiments. Experiments under constant soil moisture conditions were conducted at a water potential of −15 kPa and the sets which were run under fluctuating soil moisture conditions were subjected to eight drying-rewetting cycles where they were dried to a water potential of around −200 kPa and rewetted to −15 kPa. Mineralization was monitored continuously over a period of 56 d. Every two weeks the pesticide residues in soil pore water (PW), the methanol-extractable pesticide residues, the non-extractable residues (NER), and the total cell counts were determined. In the soil with FH conditions, mineralization of atrazine as well as the formation of the intermediate product deisopropyl-2-hydroxyatrazine was increased compared to the soil with constant humidity. In general, we found a significant correlation between the formation of this metabolite and atrazine mineralization. The cell counts were not different in the two experimental variants. These results indicate that the microbial activity was not a limiting factor but the mineralization of atrazine was essentially controlled by the bioavailability of the parent compound and the degradation product deisopropyl-2-hydroxyatrazine.     

Spatial and seasonal variations in atrazine and metolachlor surface water concentrations in Ontario (Canada) using ELISA

Concerns regarding the impacts of pesticides on aquatic species and drinking water sources have increased demands on water quality monitoring programs; however the costs of sample analysis can be prohibitive. In this study we investigated enzyme-linked immunosorbent assay (ELISA) as a cost-effective, high through-put method for measuring pesticide concentrations in surface waters. Seven hundred and thirty-nine samples from 158 locations throughout Ontario were analysed for atrazine and metolachlor from April to October 2007. Concentrations ranged from <0.1 to 3.91 μg L⁻¹ (median = 0.12 μg L⁻¹) for atrazine and from <0.1 to 1.83 μg L⁻¹ (median = 0.09 μg L⁻¹) for metolachlor. Peak concentrations occurred in late spring/early summer, in rural agricultural locations, and decreased over the remainder of the growing season for both herbicides. About 3% of the samples that had ELISA results occurring above the limit of quantification (0.10 μg L⁻¹) were evaluated against gas chromatography-mass spectrometry (GC-MS). Linear regression analysis revealed a R² value of 0.88 and 0.39, for atrazine and metolachlor, respectively. ELISA tended to overestimate concentrations for atrazine and metolachlor, most likely because the ELISA kits also detect their metabolites. Atrazine data suggest that ELISA may be used complementary with GC-MS analysis to enhance the spatial and temporal resolution of a water quality monitoring study. The commercially available metolachlor ELISA kit requires further investigation. ELISA may be used to detect atrazine and metolachlor in surface water samples, but it is not recommended as a quantitative replacement for traditional analytical methods.     

Biotransformation of atrazine and metolachlor within soil profile and changes in microbial communities

Biotransformation studies of atrazine, metolachlor and evolution of their metabolites were carried out in soils and subsoils of Northern Greece. Trace atrazine, its metabolites and metolachlor residues were detected in field soil samples 1 year after their application. The biotransformation rates of atrazine were higher in soils and subsoils of field previously exposed to atrazine (maize field sites) than in respective layers of the field margin. The DT₅₀ values of atrazine ranged from 5 to 18 d in the surface layers of the adapted soils. DT₅₀ values of atrazine increased as the soil depth increased reaching the value of 43 d in the 80-110 cm depth layer of adapted soils. Metolachlor degraded at slower rates than atrazine in surface soils, subsoils of field and field margins with the respective DT₅₀ values ranging from 56 to 72 d in surface soils and from 165 to 186 d in subsoils. Hydroxyatrazine was the most frequently detected metabolite of atrazine. The maximum concentrations of metolachlor-OXA and metolachlor-ESA were detected in the soil layers of 20-40 cm depth after 90 d of incubation. Principal Component Analysis (PCA) of soil Phospholipid Fatty Acids (PLFAs), fungal/bacterial and Gram-negative/Gram-positive ratios of the PLFA profiles revealed that the higher biotransformation rates of atrazine were simultaneously observed with the abundance of Gram-negative bacteria while the respective rates of metolachlor were observed in soil samples with abundance of fungi.     

Phytoremediation potential of the novel atrazine tolerant Lolium multiflorum and studies on the mechanisms involved

Atrazine impact on human health and the environment have been extensively studied. Phytoremediation emerged as a low cost, environmental friendly biotechnological solution for atrazine pollution in soil and water. In vitro atrazine tolerance assays were performed and Lolium multiflorum was found as a novel tolerant species, able to germinate and grow in the presence of 1 mg kg⁻¹ of the herbicide. L. multiflorum presented 20% higher atrazine removal capacity than the natural attenuation, with high initial degradation rate in microcosms. The mechanisms involved in atrazine tolerance such as mutation in psbA gene, enzymatic detoxification via P₄₅₀ or chemical hydrolysis through benzoxazinones were evaluated. It was demonstrated that atrazine tolerance is conferred by enhanced enzymatic detoxification via P₄₅₀. Due to its atrazine degradation capacity in soil and its agronomical properties, L. multiflorum is a candidate for designing phytoremediation strategies for atrazine contaminated agricultural soils, especially those involving run-off avoiding.     

Sorption of atrazine and phenanthrene by organic matter fractions in soil and sediment

Atrazine and phenanthrene (Phen) sorption by nonhydrolyzable carbon (NHC), black carbon (BC), humic acid (HA) and whole sediment and soil samples was examined. Atrazine sorption isotherms were nearly linear. The single-point organic carbon (OC)-normalized distribution coefficients (K_OC) of atrazine for the isolated HA1, NHC1 and BC1 from sediment 1 (ST1) were 36, 550, and 1470 times greater than that of ST1, respectively, indicating the importance of sediment organic matter, particularly the condensed fractions (NHC and BC). Similar sorption capacity of atrazine and Phen by NHC but different isotherm nonlinearity indicated different sorption domains due to their different structure and hydrophobicity. The positive relationship between (O + N)/C ratios of NHC and atrazine log K_OC at low concentration suggests H-bonding interactions. This study shows that sediment is probably a less effective sorbent for atrazine than Phen, implying that atrazine applied in sediments or soils may be likely to leach into groundwater.     

Waste water treatment plants as sources of polyfluorinated compounds, polybrominated diphenyl ethers and musk fragrances to ambient air

To investigate waste water treatment plants (WWTPs) as sources of polyfluorinated compounds (PFCs), polybrominated diphenyl ethers (PBDEs) and synthetic musk fragrances to the atmosphere, air samples were simultaneously taken at two WWTPs and two reference sites using high volume samplers. Contaminants were accumulated on glass fiber filters and PUF/XAD-2/PUF cartridges, extracted compound-dependent by MTBE/acetone, methanol, or hexane/acetone and detected by GC-MS or HPLC-MS/MS. Total (gas + particle phase) concentrations ranged from 97 to 1004 pg m⁻³ (neutral PFCs), <MQL to 13 pg m⁻³ (ionic PFCs), 5781 to 482,163 pg m⁻³ (musk fragrances) and <1 to 27 pg m⁻³ (PBDEs) and were usually higher at WWTPs than at corresponding reference sites, revealing that WWTPs can be regarded as sources of musk fragrances, PFCs and probably PBDEs to the atmosphere. Different concentrations at the two WWTPs indicated an influence of WWTP size or waste water origin on emitted contaminant amounts.     

Esterification of sugarcane bagasse by citric acid for Pb2+ adsorption: effect of different chemical pretreatment methods

In this study, different pretreatment strategies of sugarcane bagasse prior to citric acid modification were investigated in terms of Pb²⁺ adsorption capacity. Pretreatment strategies included the use of NaOH, HCl, and C₂H₅OH in various concentrations. In order to fundamentally understand how these pretreatment methods affect the modification of sugarcane bagasse by citric acid as well as the Pb²⁺ adsorption capacity of sugarcane bagasse, three main components of sugarcane bagasse namely cellulose, hemicellulose, and lignin were isolated and esterified by citric acid under the same conditions. ATR-FTIR, XPS, SEM, and an analysis of the number of carboxylic acid groups were used to investigate the physicochemical and chemical properties of the materials. These three components were proved to participate in adsorption and induce the esterification with citric acid. Hence, pretreatment with ethanol and 0.01 M NaOH which could retain cellulose, hemicellulose, and lignin in sugarcane bagasse achieved a high Pb²⁺ adsorption capacity, i.e., 122.4 and 97 mg/g after the esterification with citric acid. In contrast, pretreatment with 0.5 M NaOH and 0.1 M HCl removed lignin and hemicellulose, leading to the lowest value of approximately 45 mg/g for citric acid esterified-pretreated sugarcane bagasse. XPS analysis and number of carboxylic group measurement confirmed the esterification between bagasse and citric acid. To understand the adsorption mechanism of adsorbent, two kinetic models including pseudo-first-order model and pseudo-second-order model were applied. The experimental data were well described by the pseudo-second-order model. The adsorption isotherm data were fitted Langmuir and Freundlich.

     

Passive dosing: an approach to control mutagen exposure in the Ames fluctuation test

By using dialysis equilibrium experiments, the sorption of a branched nonylphenol isomer [4-(1-ethyl-1,3-dimethylpentyl)-phenol] (NP111) on various humic acids (HAs) isolated from river sediments and two reference HAs was studied. The HAs were characterized by solid-state ¹³C direct polarization/magic angle spinning nuclear magnetic resonance (¹³C DP/MAS NMR) spectroscopy. Sorption isotherms of NP111 on HAs were described by a linear model. The organic carbon-normalized sorption coefficient (K_OC) ranged from 2.3 × 10³ to 1.5 × 10⁴ L kg⁻¹. Interestingly, a clear correlation between K_OC value and alkyl C content was observed, indicating that the aliphaticity of HAs markedly dominates the sorption of NP111. These new mechanistic insights about the NP111 sorption indicate that the fate of nonylphenols in soil or sediment depends not only on the content of HA, but also on its structural composition.     

Long-term dynamics of the atrazine mineralization potential in surface and subsurface soil in an agricultural field as a response to atrazine applications

The dynamics of the atrazine mineralization potential in agricultural soil was studied in two soil layers (topsoil and at 35-45 cm depth) in a 3 years field trial to examine the long term response of atrazine mineralizing soil populations to atrazine application and intermittent periods without atrazine and the effect of manure treatment on those processes. In topsoil samples, ¹⁴C-atrazine mineralization lag times decreased after atrazine application and increased with increasing time after atrazine application, suggesting that atrazine application resulted into the proliferation of atrazine mineralizing microbial populations which decayed when atrazine application stopped. Decay rates appeared however much slower than growth rates. Atrazine application also resulted into the increase of the atrazine mineralization potential in deeper layers which was explained by the growth on leached atrazine as measured in soil leachates recovered from that depth. However, no decay was observed during intermittent periods without atrazine application in the deeper soil layer. atzA and trzN gene quantification confirmed partly the growth and decay of the atrazine degrading populations in the soil and suggested that especially trzN bearing populations are the dominant atrazine degrading populations in both topsoil and deeper soil. Manure treatment only improved the atrazine mineralization rate in deeper soil layers. Our results point to the importance of the atrazine application history on a field and suggests that the long term survival of atrazine degrading populations after atrazine application enables them to rapidly proliferate once atrazine is again applied.     

Water quality parameters controlling the photodegradation of two herbicides in surface waters of the Columbia Basin,Washington

The water quality parameters nitrate-nitrogen, dissolved organic carbon, and suspended solids were correlated with photodegradation rates of the herbicides atrazine and 2,4-D in samples collected from four sites in the Columbia River Basin, Washington, USA. Surface water samples were collected in May, July, and October 2010 and analyzed for the water quality parameters. Photolysis rates for the two herbicides in the surface water samples were then evaluated under a xenon arc lamp. Photolysis rates of atrazine and 2,4-D were similar with rate constants averaging 0.025 h⁻¹ for atrazine and 0.039 h⁻¹ for 2,4-D. Based on multiple regression analysis, nitrate-nitrogen was the primary predictor of photolysis for both atrazine and 2,4-D, with dissolved organic carbon also a predictor for some sites. However, at sites where suspended solids concentrations were elevated, photolysis rates of the two herbicides were controlled by the suspended solids concentration. The results of this research provide a basis for evaluating and predicting herbicide photolysis rates in shallow surface waters.     

Stability considerations of aspartame in the direct analysis of artificial sweeteners in water samples using high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS)

A HPLC-MS/MS method is presented for the simultaneous determination of frequently used artificial sweeteners (ASs) and the main metabolite of aspartame (ASP), diketopiperazine (DKP), in environmental water samples using the direct-injection (DI) technique, thereby achieving limits of quantification (LOQ) of 10 ng L⁻¹. For a reliable quantification of ASP pH should be adjusted to 4.3 to prevent formation of the metabolite. Acesulfame (ACE), saccharin (SAC), cyclamate (CYC) and sucralose (SUC) were ubiquitously found in water samples. Highest concentrations up to 61 μg L⁻¹ of ACE were found in wastewater effluents, followed by surface water with concentrations up to 7 μg L⁻¹, lakes up to 600 ng L⁻¹ and groundwater and tap water up to 70 ng L⁻¹. The metabolite DKP was only detected in wastewater up to 200 ng L⁻¹ and at low detection frequencies.     

Transformation of tetrabromobisphenol A in the presence of different solvents and metals

Solvent-based separation method is presumably an efficient and environmentally beneficial approach for elimination of brominated flame retardants (BFRs) from waste electrical and electronic equipment (WEEE). The overall goal of this study was to evaluate possible effects of organic solvent on the behavior of BFRs during solvent-based processing of WEEE. We initiated a set of batch experiments for examining the rates and possible pathways of transformation of a representative BFR (tetrabromobisphenol A, TBBPA) using acetone, toluene, and methanol as the solvents. Our results showed that toluene and methanol had no effect on the transformation of TBBPA, but approximately 20% of TBBPA (100 mg L⁻¹) was transformed by acetone within 2 h at 50 °C. Analysis of the products with GC-MS showed that two high-molecular-weight products (MW = 586) were major products of the transformation reactions. The role of acetone as a reactant in the transformation of TBBPA was further validated with dueterated acetone. In addition, the effects of co-existing metals in WEEE (i.e., Zn, Cu, and Ni) on the transformation of TBBPA in the solvent systems were investigated. These metals tested were found to greatly enhance the rates of TBBPA transformation. The metal facilitated solvent reactions with TBBPA may lower the extractability of TBBPA by formation of larger and less soluble products, hence potentially increasing the cost for separating the chemical from WEEE.     

Dechlorination of PCBs in the simulative transformer oil by microwave-hydrothermal reaction with zero-valent iron involved

The conventional hydrothermal reaction with iron powder, NaOH and H₂O as reactants was reported to occur at temperature above 423 K, and iron oxides (Fe₃O₄ and NaFeO₂) and hydrogen were produced. In this study, microwave heating was adopted to take the place of conventional heating to induce the hydrothermal reaction. Under microwave irradiation, NaOH and H₂O absorbed microwave energy by space charge polarization and dipolar polarization and instantly converted it into thermal energy, which initiated the hydrothermal reaction that involved with zero-valent iron. X-ray diffraction (XRD) analysis found Fe₃O₄/NaFeO₂ and confirmed the occurrence of microwave-induced hydrothermal reaction. The developed microwave-hydrothermal reaction was employed for the dechlorination of PCBs. Hexadecane containing 100 mg L⁻¹ of Aroclor1254 was used as simulative transformer oil, and the dechlorination of PCBs was evaluated by GC/ECD, GC/MS and ion chromatography. For PCBs in 10 mL simulative transformer oil, almost complete dechlorination was achieved by 750 W microwave irradiation for 10 min, with 0.3 g iron powder, 0.3 g NaOH and 0.6 mL H₂O added. The effects of important factors including microwave power and the amounts of reactants added, on the dechlorination degree were investigated, moreover, the dechlorination mechanism was suggested. Microwave irradiation combined with the common and cheap materials, iron powder, NaOH and H₂O, might provide a fast and cost-effective method for the treatment of PCBs-containing wastes.     

Comparative assessment of metribuzin sorption efficiency of biochar,hydrochar and vermicompost

Abstract

In this study, we used two biochars (BC) produced from grapevine pruning residues (BCgv) and red spruce wood (BCrs), two hydrochars (HC) from urban pruning residues (HCup) and the organic fraction of municipal solid wastes (HCuw), and two vermicomposts (VC) obtained vermicomposting digestates from buffalo manure (VCbm) and mixed feedstock (VCmf). Adsorption kinetics and isotherms of metribuzin onto these materials were performed. Sorption kinetics followed preferentially a pseudo-second-order model, thus indicating the occurrence of chemical interactions between the sorbate and the adsorbents. Adsorption constants were calculated using the Freundlich and Langmuir models. Metribuzin sorption data on BCgv and both HC fitted preferentially the Freundlich equation, whereas on the other materials data fitted both isotherms well (r?>?0.95). Metribuzin sorption capacity of the materials followed the trend BC?>?HC?>?VC. Sorption constants of metribuzin normalised per organic carbon content (K_OC) on BCgv, BCrs, HCup, HCuw, VCbm and VCmf were 561, 383, 251, 214, 102 and 84?L kg^?1, respectively. A significant positive correlation (P?=?0.016) was calculated between distribution coefficients (K_d) of all materials and the corresponding organic carbon contents, thus indicating a prominent role of the organic fraction of these materials in the adsorption of metribuzin.     

Ecotoxicity evaluation of selected sulfonamides

Sulfonamides (SAs) are a group of antibiotic drugs widely used in veterinary medicine. The contamination of the environment by these pharmaceuticals has raised concern in recent years. However, knowledge of their (eco)toxicity is still very basic and is restricted to just a few of these substances. Even though their toxicological analysis has been thoroughly performed and ecotoxicological data are available in the literature, a systematic analysis of their ecotoxicological potential has yet to be carried out. To fill this gap, 12 different SAs were chosen for detailed analysis with the focus on different bacteria as well as non-target organisms (algae and plants). A flexible (eco)toxicological test battery was used, including enzymes (acetylcholinesterase and glutathione reductase), luminescent marine bacteria (Vibrio fischeri), soil bacteria (Arthrobacter globiformis), limnic unicellular green algae (Scenedesmus vacuolatus) and duckweed (Lemna minor), in order to take into account both the aquatic and terrestrial compartments of the environment, as well as different trophic levels. It was found that SAs are not only toxic towards green algae (EC₅₀ = 1.54-32.25 mg L⁻¹) but have even stronger adverse effect on duckweed (EC₅₀ = 0.02-4.89 mg L⁻¹) than atrazine - herbicide (EC₅₀ = 2.59 mg L⁻¹).     

Atrazine promotes biochemical changes and DNA damage in a Neotropical fish species

The effects of Atrazine, an herbicide used worldwide and considered as a potential contaminant in aquatic environments, were assessed on the Neotropical fish Prochilodus lineatus acutely (24 and 48 h) exposed to 2 or 10 μg L⁻¹ of atrazine by using a set of biochemical and genetic biomarkers. The following parameters were measured in the liver: activity of the biotransformation enzymes ethoxyresorufin-O-deethylase (EROD) and glutathione S transferase (GST), antioxidant enzymes superoxide dismutase (SOD), catalase (CAT), glutathione peroxidase (GPx), glutathione reductase (GR), content of reduced glutathione (GSH), generation of reactive oxygen species (ROS) and occurrence of lipid peroxidation (LPO); in brain and muscle the activity of acetylcholinesterase (AChE) and DNA damage (comet assay) on erythrocytes, gills and liver cells. A general decreasing trend on the biotransformation and antioxidant enzymes was observed in the liver of P. lineatus exposed to atrazine; except for GR, all the other antioxidant enzymes (SOD, CAT and GPx) and biotransformation enzymes (EROD and GST) showed inhibited activity. Changes in muscle or brain AChE were not detected. DNA damage was observed in the different cell types of fish exposed to the herbicide, and it was probably not from oxidative origin, since no increase in ROS generation and LPO was detected in the liver. These results show that atrazine behaves as enzyme inhibitor, impairing hepatic metabolism, and produces genotoxic damage to different cell types of P. lineatus.     

Effects of estrone on the early life stages and expression of vitellogenin and estrogen receptor genes of Japanese medaka (Oryzias latipes)

The fertilized eggs of Japanese medaka (Oryzias latipes) were exposed to estrone (E1) at 5–5000 ng L⁻¹ for 15 d, and the hatched fry were exposed continuously to the same concentrations for the additional 15 d. Adverse effects on hatchability, time to hatching, and gross abnormalities occurred at 50 ng L⁻¹ or above. Then the fry were divided into a continual exposure group, and a water recovery group. When the fry were exposed to E1 for another 60 d, there was a decrease in the hepatosomatic index (HSI) of males and the influence disappeared in the water recovery group. The gonadosonatic index (GSI) of females at 500 ng L⁻¹ decreased significantly in another 60 d exposure. While the fry were maintained in dechlorinated tap water for 60 d, a significant decrease in female GSI was observed at 50 ng L⁻¹ or above. An increased GSI was found in males in both continual exposure and water recovery groups at all E1 treatments. Quantitative RT-PCR showed that vitellogenin-I (Vtg-I) gene expressions in the female liver were significantly down-regulated at 50 ng L⁻¹ in the continual exposure group, and at 500 ng L⁻¹ in the water recovery group, while male Vtg-I genes were significantly up-regulated for all E1 treatments. In addition, all E1 treatments caused sex reversal of males. These results suggest that E1 at 5 ng L⁻¹ or above have unrecoverable impacts on the gonadal growth and development of medaka, even if only early life stages were exposed to E1.