Fate and transport of monoterpenes through soils. Part I. Prediction of temperature dependent soil fate model input-parameters

Monoterpenes are C10H(n)O(n') compounds of natural origin and are potentially environmentally safe substitutes for traditional pesticides. Still, an assessment of their environmental behaviour is required. As a first step in a theoretical study focussing on monoterpenes applied as pesticides to terrestrial environments, soil fate model input-parameters were determined for 20 monoterpenes with widely different structural characteristics. Input-parameters are the water solubility (S(W)), vapour pressure (P), n-octanol-water partition coefficient (K(OW)), atmospheric air and bulk water diffusion coefficients (D(A)air and D(W)water), first order biodegradation rate constants (k), and their temperature dependence. Values for these parameters were estimated or taken from previous experimental work. The quality of the estimations was discussed by focussing on their statistics and by comparison with available experimental data. From these properties, the air-water partition coefficient (K(AW), Henry's Law constant), the interface-water partition coefficient (K(IW)) and the organic matter-water partition coefficient (K(OM)) could be estimated with varying levels of accuracy. In general, little experimental data turned out to be available on biodegradation rate constants and on the temperature dependence of physico-chemical parameters.     

Methane emission from lakes

A physico-chemical model to describe methane and carbon dioxide emission from lakes was developed. The model describes the emission by diffusion, bubbles and plants. The intensity of the fluxes can be calculated either for total or particular emission in dependence on gas bubbles composition. It was found, that diffusional (Q) and bubble (J) fluxes depend on the methane molar ratio (X) in bubbles as follows: [formula: see text]. The model allows to estimate the role of the methane oxidation by atmospheric oxygen in the total methane flux. It was shown, that the methane oxidation does not influence much methane fluxes to the atmosphere for most of the experimentally observed situations.     

Diffusion of PAH and PCB from contaminated sediments with and without mineral capping; measurement and modelling

A novel laboratory microcosm test was developed to measure the diffusion of native PAHs and PCBs from sediments in the presence and absence of a capping layer. Diffusive flux of 15 PAHs and 7 PCBs from uncapped sediment from Oslo harbour was 3.8+/-0.9 microg m(-2)d(-1) and 0.010+/-0.003 microg m(-2)d(-1), respectively. The flux from sediments capped with 1cm mineral cap (crushed limestone or crushed gneiss (0-2mm)), observed during the first 410 d, was 3.5-7.3% of the flux from uncapped sediments. By measuring freely dissolved pore water concentrations of 10 PAHs the flux in the microcosm was modelled with steady state and transient diffusion models. The measured flux from uncapped sediment was 27-290% of modelled steady state flux. Good agreement was also found between the measured flux of pyrene from capped sediment and the flux modelled with the transient model when fitting only with the distribution coefficients for pyrene between the cap material and water (Kd_pyr). Fitted Kd_pyr, (210 and 23 l kg(-1) for limestone and gneiss, respectively) was in the same order of magnitude as K(d) calculated from organic carbon content in the cap materials (68 and 14 l kg(-1) respectively). Calculation of the efficiency of a hypothetical cap with 10 cm diffusion path shows that the increased diffusion path length alone can yield a flux reduction >99% through a strong increase in the stagnant diffusive boundary layer from <1 to 100mm.     

Geologic emissions of methane to the atmosphere

The atmospheric methane budget is commonly defined assuming that major sources derive from the biosphere (wetlands, rice paddies, animals, termites) and that fossil, radiocarbon-free CH4 emission is due to and mediated by anthropogenic activity (natural gas production and distribution, and coal mining). However, the amount of radiocarbon-free CH4 in the atmosphere, estimated at approximately 20% of atmospheric CH4, is higher than the estimates from statistical data of CH4 emission from fossil fuel related anthropogenic sources. This work documents that significant amounts of "old" methane, produced within the Earth crust, can be released naturally into the atmosphere through gas permeable faults and fractured rocks. Major geologic emissions of methane are related to hydrocarbon production in sedimentary basins (biogenic and thermogenic methane) and, subordinately, to inorganic reactions (Fischer-Tropsch type) in geothermal systems. Geologic CH4 emissions include diffuse fluxes over wide areas, or microseepage, on the order of 10(0)-10(2) mg m(-2) day(-1), and localised flows and gas vents, on the order of 10(2) t y(-1), both on land and on the seafloor. Mud volcanoes producing flows of up to 10(3) t y(-1) represent the largest visible expression of geologic methane emission. Several studies have indicated that methanotrophic consumption in soil may be insufficient to consume all leaking geologic CH4 and positive fluxes into the atmosphere can take place in dry or seasonally cold environments. Unsaturated soils have generally been considered a major sink for atmospheric methane, and never a continuous, intermittent, or localised source to the atmosphere. Although geologic CH4 sources need to be quantified more accurately, a preliminary global estimate indicates that there are likely more than enough sources to provide the amount of methane required to account for the suspected missing source of fossil CH4.     

Distribution and fractionation of phosphorus, cadmium, nickel, and lead in calcareous soils amended with composts

Composts improve organic carbon content and nutrients of calcareous soils but the accumulation and distribution of phosphorus and heavy metals among various fractions in soil may vary under the south Florida conditions. The accumulation of P, Cd, Ni, and Pb with depth and the distribution of water soluble, exchangeable, carbonate, Fe-Mn oxides, organic and residual forms of each element were investigated in soils amended with municipal solid waste (MSW) compost, co-compost and biosolids compost and inorganic fertilizer (as control). Total concentrations of P, Cd, Ni, and Pb were higher in the 0-22 cm soil layers and decreased considerably in the rock layers. These elements were in the decreasing order of P > Pb > Ni > Cd. Amounts of water soluble and exchangeable forms of P, Cd, Ni and Pb were negligible at 0-22 cm soil depths except for Cd in the 10-22 cm depth. Amending calcareous soil with either organic or inorganic amendments rendered phosphorus, nickle and lead in the residual form followed by Fe-Mn oxides form in the 0-10 and 10-22 cm soil layers. Cadmium was predominantly in the Fe-Mn oxides fraction followed by the residual and carbonate forms in both soil layers. A significant positive correlation was found between various organic carbon fractions and organic forms of P, Cd and Pb in the surface soil layer. Soil amended with MSW compost had higher concentration of Cd in the organic fraction whereas, co-compost and MSW compost amended soil had higher concentrations of organic Ni fraction in the 0-10 cm soil layer.     

Solar photodegradation of dichloroacetic acid and 2,4-dichlorophenol using an enhanced photo-Fenton process

The photo-Fenton process using potassium ferrioxalate as a mediator was investigated for the photodegradation of dichloracetic acid (DCA) and 2,4-dichlorophenol (DCP) in aqueous medium using solar light as source of irradiation. The influence of the solution depth, the light intensity and the effect of stirring the solution during irradiation process were evaluated using DCA as a model compound. A negligible influence of stirring the solution was observed when the concentration of ferrioxalate (FeOx) was 0.8 mM and solution depth was 4.5 or 14 cm. The optimum FeOx concentration determined for solution depths between 4.5 and 14 cm was 0.8 mM considering total organic carbon (TOC) removal during DCA irradiation. The high efficiency of the photo-Fenton process was demonstrated on summer days, when only 10 min of exposition (around noon) were sufficient to completely destroy the organic carbon of a 1.0 mM DCA solution in the presence of 0.8 mM FeOx and 6.0 mM H2O2 using a solution depth of 4.5 cm. It was observed that the photodegradation efficiency increases linearly with the solar light intensity up to values around 15 Wm(-2) but this linear relationship does not hold above this value showing a square root dependence. The photodegradation of a solution of DCP/FeOx showed a lower TOC removal rate than that observed for DCA/FeOx, achieving approximately 90% after 35 min irradiation under 19 W m(-2), while under this light intensity, the same TOC removal of DCA/FeOx was achieved in only 10 min irradiation.     

Influence of plants on the methane emission from sediments

The previous theory [Chem. Global Change Sci. 3 (2001) 33; Chemosphere 50 (2003) 191] of methane emission is applied to vegetated sediments. The presence of roots in a sediment is taken into account. It is assumed that methane and nitrogen enter a sediment through channels existing in plants and roots. The rate of methane and nitrogen transport through plants and roots is proportional to the difference in concentrations in the layer and on the upper surface. It is established that as the vegetation density increases, the rate of methane transport increases so that with sufficient vegetation density, almost all methane passes to the atmosphere through plants. In this case, the value of bubble emission decreases to zero. The nitrogen transport rate through plants first increases and then decreases with increasing the vegetation density. The theory qualitatively and quantitatively describes the dependence of methane concentration on depth in the presence of plants. A comparison with the available experimental data on dissolved methane concentration and bubble composition indicates satisfactory agreement.     

Rare earth elements in naturally grown fern Dicranopteris linearis in relation to their variation in soils in south-Jiangxi region (southern China)

Ferns (Dicranopteris linearis) and soils, sampled from four rare earth mining areas and one non-mining area locating in South-Jiangxi region, were chosen for analysis of 15 rare earth elements (REEs) by inductively coupled plasma-mass spectrometry (ICP-MS). The fern samples were divided into 4 parts: root, stem, petiole, and lamina. The soils of the same sites were also sampled, and 4 soil layers were observed at the profile: A (0-20 cm depth), B (20-150 cm depth), C (150-400 cm depth), and D (rock). The distribution patterns and transportation characteristics of REEs of different soil layers and of different parts of D. linearis were studied. The results showed that in the soil layers, the sigma REE (the sum of the concentrations of 15 REEs) of A layer, as well as B layer were lower than that of C layer, but Ce was relatively concentrated in A layer. The sigma REE of different parts of D. linearis were lamina, root > stem > petiole. The REE distribution patterns of D. linearis root were similar to the total REE distribution patterns of the A layer of their host soils, especially to the soluble REE distribution patterns of the A layer of their host soils. The REEs were fractionated in their transportation in D. linearis. The abundances of heavy rare earth elements (HREEs, Gd to Lu and Y) in the stem, petiole, lamina are lower than those in the root.     

Distribution and Fractionation of Phosphorus,Cadmium, Nickel,and Lead in Calcareous Soils Amended with Composts

Abstract

Composts improve organic carbon content and nutrients of calcareous soils but the accumulation and distribution of phosphorus and heavy metals among various fractions in soil may vary under the south Florida conditions. The accumulation of P, Cd, Ni, and Pb with depth and the distribution of water soluble, exchangeable, carbonate, Fe–Mn oxides, organic and residual forms of each element were investigated in soils amended with municipal solid waste (MSW) compost, co-compost and biosolids compost and inorganic fertilizer (as control). Total concentrations of P, Cd, Ni, and Pb were higher in the 0–22 cm soil layers and decreased considerably in the rock layers. These elements were in the decreasing order of P ? Pb > Ni > Cd. Amounts of water soluble and exchangeable forms of P, Cd, Ni and Pb were negligible at 0–22 cm soil depths except for Cd in the 10–22 cm depth. Amending calcareous soil with either organic or inorganic amendments rendered phosphorus, nickle and lead in the residual form followed by Fe–Mn oxides form in the 0–10 and 10–22 cm soil layers. Cadmium was predominantly in the Fe–Mn oxides fraction followed by the residual and carbonate forms in both soil layers. A significant positive correlation was found between various organic carbon fractions and organic forms of P, Cd and Pb in the surface soil layer. Soil amended with MSW compost had higher concentration of Cd in the organic fraction whereas, co-compost and MSW compost amended soil had higher concentrations of organic Ni fraction in the 0–10 cm soil layer.     

A method for the in-situ determination of dissolved methane in groundwater in shallow aquifers

Dissolved methane in groundwater has potential for use as a tracer of waste contamination in aquifers, and is itself a contaminant of concern because of potential explosion hazards following pumping of groundwater to the surface. A technique is described and evaluated for in-situ determination of the variation in concentration of dissolved methane with depth in shallow aquifers. The technique uses diffusion cells (small diameter teflon tubes) buried in boreholes and connected to the surface by small diameter nylon access tubes. A stream of gas is passed through the cells until a steady flux of methane is obtained. The steady state flux can then be related to concentration or partial pressure of methane in groundwater in contact with the cell, from prior laboratory calibration. Some temperature compensation is required.Two strings of cells with nylon access tubes for gas purging have been emplaced in permeable grout within boreholes drilled in sand a aquifer. The depth-related concentrations of dissolved methane found using these cells compare reasonably well with less precise data obtained by sampling of conventional boreholes situated adjacent to each string of cells.     

模拟生物反应器加速产甲烷过程研究

渗滤液原液回灌易导致填埋垃圾产甲烷过程的滞后,从而对甲烷收集利用产生不利影响。通过3根实验室模拟生物反应器,研究了原液回灌(C1)、渗滤液好氧预处理后回灌(C2)和原液回灌+垃圾层上部通风曝气(C3)3种填埋方式下的填埋气产气规律。结果表明,C1甲烷浓度经历短暂上升,达到19.5%后开始逐渐降低,产甲烷速率和产甲烷总量均很低;C2甲烷浓度逐渐上升,在第121天时甲烷浓度达到50%,产甲烷最高速率和产甲烷总量分别为0.31 L/(kg·d)和25.2 L/kg。在停止上部垃圾层通风曝气后,C3甲烷浓度迅速上升,在81 d时甲烷浓度便达到50%以上,最大产甲烷速率和产甲烷总量分别为0.22 L/(kg·d)和16.0 L/kg。对各模拟柱填埋气可回收性评价结果表明,C3填埋气可回收利用比例最高,C2略低,C1在实验期间内则无可回收利用气体产生。     

The relationship between elimination rates and partition coefficients

Rate constants for uptake and elimination of chemicals in organisms are often related to partition coefficients (typically the octanol-water partition coefficient). We show that the well-mixed one-compartment model for toxico-kinetics implies that the elimination rate is inversely proportional to the square root of the partition coefficient. When chemical exchange is limited by diffusion in the boundary layers adjacent to the interface, two-film models are appropriate, which have more complex implications for the relationships between the exchange rates and the partition coefficient. We also show that the popular steady-flux approximation of the two-film model is not a conceptual generalization of the one-compartment model, although it shares the first-order kinetics. We compare the kinetics of a series of models with an increasing number of well-mixed compartments for exchange, such that the two-film model results for an infinite number of compartments. The latter model formulation in terms of partial differential equations, and more in particular its boundary condition at the interface of the two media, is believed to be new. In the steady-flux approximation and in the model with single well-mixed boundary layers and low diffusivities, the elimination rate depends hyperbolically on the partition coefficient. The available data for abiotic systems (SPME fibers) supports a hyperbolic relationship, whereas the data for aquatic biota are less discriminating between a hyperbolic or a square root relationship with the partition coefficient. The daphnia data showed less scatter than the fish data, possibly due to the small variance in body sizes, since elimination rates are inversely proportional to body length. The square root relationship fitted these data best.     

Combination of photoacoustic detector with gas diffusion probes for the measurement of methane concentration gradients in submerged paddy soil

Dissolved methane was monitored by means of a diffusion probe in combination with a photoacoustic (PA) detector cell placed in the cavity of a liquid nitrogen-cooled CO laser. The detection limit of the photoacoustic detector was 1 ppbv methane (≈ 2 μM in aqueous solution), the time response was 60 s, the spatial resolution was 1.36 mm. These limits were determined by the acoustic noise and the configuration of the diffusion probe. The combination of PA detector with gas diffusion probes was found to be useful for monitoring gaseous compounds. However, the membrane material of the diffusion probe was critical. Silicone as membrane material was useful only for measurement of CH₄. Goretex as membrane material was applicable to measurement of dimethylsulfide (DMS), but did not give a stable signal for trimethylamine (TMA).

Vertical concentration profiles of CH₄ in anoxic paddy soil agreed well with earlier results obtained with a gas chromatograph as detector. Methane was produced in anoxic soil layers below 8–10 mm depth and diffused upwards to the surface through a layer of CH₄-consuming bacteria situated at about 2 mm depth. In the oxic upper 2 mm soil layer the concentration of CH₄ decreased below the detection limit of our system. Methane-containing gas bubbles that were embedded in the soil were detected by a steep increase of the CH₄ signal. The combination of PA detector and gas diffusion probe was found to be a useful tool to measure CH₄ gradients in submerged soil or sediment with high temporal and spatial resolution, thus allowing the localization and quantification of CH₄ production and CH₄ oxidation rates within the soil profile.     

Direct simulation of heterogeneous diffusion and inversion procedure applied to an out-diffusion experiment. Test case of Palmottu granite

An out-diffusion laboratory experiment using a non-reactive tracer was fitted using the Time Domain Diffusion (TDD) method. This rapid particle tracking method allows simulation of the heterogeneous diffusion based on pore-scale images and local values of diffusivities. The superimposed porosity and mineral 2D maps act as computation grids to condition diffusion pathways. We focused on a Palmottu granite sample, in which the connected pore space has a composite microstructure with cracks linking microporous minerals and is above the percolation threshold. Three main results were achieved: (i) When compared to the fitting obtained with one coefficient (best mean square residual R = 1.6 x 10(-2)), diffusion is shown to be suitably characterised with two coefficients related to cracks and microporous minerals (best R = 6.5 x 10(-4)), (ii) rather than imposing a local apparent diffusion coefficient D(a) independent of the local porosity Phi, a best fit is obtained by applying Archie's relationship D(a) = D(0) x G with G = Phi(m) to each pixel of the calculation grids (G is the geometry factor, D(0) is the diffusion coefficient in free fluid, and m is Archie's exponent), and (iii) the order of magnitude of the fitted diffusion coefficient or Archie's exponents (m=0 for microcracks and m=1.82 for microporous minerals) is physically realistic.     

Diffusive flux and pore anisotropy in sedimentary rocks

Diffusion of dissolved contaminants into or from bedrock matrices can have a substantial impact on both the extent and longevity of dissolved contaminant plumes. For layered rocks, bedding orientation can have a significant impact on diffusion. A series of laboratory experiments was performed on minimally disturbed bedrock cores to measure the diffusive flux both parallel and normal to mineral bedding of four different anisotropic sedimentary rocks. Measured effective diffusion coefficients ranged from 4.9×10(-8) to 6.5×10(-7)cm(2)/s. Effective diffusion coefficients differed by as great as 10-folds when comparing diffusion normal versus parallel to bedding. Differences in the effective diffusion coefficients corresponded to differences in the "apparent" porosity in the orientation of diffusion (determined by determining the fraction of pore cross-sectional area measured using scanning electron microscopy), with the difference in apparent porosity between normal and parallel bedding orientations differing by greater than 2-folds for two of the rocks studied. Existing empirical models failed to provide accurate predictions of the effective diffusion coefficient in either bedding orientation for all four rock types studied, indicating that substantial uncertainty exists when attempting to predict diffusive flux through sedimentary rocks containing mineral bedding. A modified model based on the apparent porosity of the rocks provided a reasonable prediction of the experimental diffusion data.     

Interaction between nitrogen and phosphorus cycles in mining-affected aquatic systems—experiences from field and laboratory measurements

The main objectives of this study were to (a) study the interaction between N and P cycles in mining-affected aquatic systems and (b) to quantify release rates of sedimentary soluble reactive phosphorus (SRP) that may be related to this interaction. Sediment cores and water from Lake Bruträsket (Boliden, northern Sweden) were collected and a time series of water sampling and flow measurements was conducted in the Brubäcken stream connected to the lake. Factors affecting SRP release were studied in a sediment incubation experiment and water column experiments. Field and laboratory measurements indicated that pH and dissolved oxygen are two important factors for SRP release. At the end of the low-oxygen incubation, an SRP concentration of 56 μg?L^?1 resulted in a sedimentary flux of 1.1 mg SRP?m^?2?day^?1. This is ～10 times higher than the flux of 0.12 mg SRP?m^?2?day^?1 obtained from depth integration of vertical SRP profiles measured in the lake, and ～100 times higher than the external flux of 0.014 mg SRP?m^?2?d^?1 into the lake (based on catchment area). Field measurements indicated that oxidation of organic matter and mining-related chemicals (ammonium and thiosulphates) may result in increased internal SRP flux from the sediment. Increased P loading in the lake as a result of low-oxygen conditions could change water column total nitrogen/total phosphorus ratios from 27 to 17, consequently changing the lake from being P-limited to be co-limited by N and P. The obtained findings point to possible interaction between the cycles of nitrogen (oxygen consumption) and P (flux from sediment) that may be important for nutrient regulation in mine water recipients.     

Contributions of advective and diffusive oxygen transport through multilayer composite caps over mine waste

The relative contributions of four mechanisms of oxygen transport in multilayer composite (MLC) caps placed over oxygen-consuming mine waste were evaluated using numerical and analytical methods. MLC caps are defined here as caps consisting of earthen and geosynthetic (polymeric) components where a composite barrier layer consisting of a geomembrane (1-2 mm thick polymeric sheet) overlying a clay layer is the primary barrier to transport. The transport mechanisms that were considered are gas-phase advective transport, gas-phase diffusive transport, liquid-phase advective transport via infiltrating precipitation and liquid-phase diffusive transport. A numerical model was developed to simulate gas-phase advective-diffusive transport of oxygen through a multilayer cap containing seven layers. This model was also used to simulate oxygen diffusion in the liquid phase. An approximate analytical method was used to compute the advective flux of oxygen in the liquid phase. The numerical model was verified for limiting cases using an analytical solution. Comparisons were also made between model predictions and field data for earthen caps reported by others. Results of the analysis show that the dominant mechanism for oxygen transport through MLC caps is gas-phase diffusion. For the cases that were considered, the gas-phase diffusive flux typically comprises at least 99% of the total oxygen flux. Thus, designers of MLC caps should focus on design elements and features that will limit diffusion of gas-phase oxygen.     

不同好氧预处理方式对餐厨垃圾产甲烷的影响

为了研究不同好氧预处理方式对餐厨垃圾厌氧消化产甲烷的影响,通过建立3个模拟厌氧生物反应器,研究了传统厌氧生物反应器C1、上层好氧预处理-厌氧生物反应器C2和底部好氧预处理-厌氧生物反应器C3 3种不同操作条件下的产甲烷过程。结果表明,挥发性有机酸的累积使C1始终处于产甲烷滞后阶段;而C2、C3的好氧预处理通过加快易水解酸化组分和过量挥发性有机酸的好氧降解,有效缓解了酸性抑制,产甲烷滞后时间明显缩短至10 d内。第32天C2停止上层曝气后,在27 d内甲烷浓度达到了50%以上,同时,产甲烷速率迅速上升,并在第81天可达到峰值773 mL/(kg·d)。C3在第11天停止底部曝气后,虽然经过22 d的时间甲烷浓度即上升至50%,但之后产甲烷速率经历回落阶段后再次逐渐上升,在实验结束时仅达到517 mL/(kg·d)。上层曝气的好氧预处理方式所需曝气时间相对较长,但其产甲烷启动快,与底部曝气相比,其后期的甲烷化过程更稳定并可达到较高的产甲烷速率。     

The diffusion and sorption of volatile organic compounds through kaolinitic clayey soils

Laboratory experiments to estimate the effective molecular diffusion coefficient (D(e)) and sorption coefficient (K(d)) for volatile organic compounds through natural clayey soils were conducted using diffusion testing apparatus. The compounds tested were methyl ethyl ketone (MEK), toluene and trichloroethylene (TCE). The D(e) and K(d) values were determined by a curve fitting procedure. The compound losses, and the effects of porous disks used in the apparatus were significant. The transport of MEK was faster than that of TCE and toluene because of the lower sorption to the soils. The D(e) values of all the compounds were of the order of 10(-10) m(2)/s and smaller than the diffusion coefficient in pure aqueous solution at infinite dilution (D(0)), due to the tortuosity of the samples. The effects of the sample thickness on the parameter determination were not significant. Comparison to the K(d) values estimated from batch sorption tests and from organic carbon content (f(oc))-based predictions showed that the diffusion test results were intermediate between those from the other two methods. The diffusion tests use compacted soil samples and should be more relevant to in situ conditions, but the reliability of the tests is affected by large compound losses that cause uncertainties in their interpretation. It is recommended that more than one method be used to assess K(d) values.     

Atmospheric deposition of macronutrients by pollen at a semi-remote site in northern Wisconsin

Pine pollen concentrations in air at a semi-remote site in northern Wisconsin attained levels of 18 and 25 μ m⁻³ in late May and early June of 1979 and 1981, respectively. The upper and lower limits for the deposition velocity of pine pollen at this site are approximately 30 and 1.3 cm s⁻¹, respectively. Consequently, the average annual pine pollen flux at this location for 1979 and 1981 was between 8.0 and 0.35 g m⁻². Deposition of total phosphorus and organic C by pollen dispersal are about 5–100% and 11–240%, respectively, of the measured bulk atmospheric loading rate in the region. Pine pollen fluxes of water-extractable K are about 10–230% of the average annual wet deposition, while the fluxes of waterextractable NO₃⁻ and SO₄⁻² by pollen appear to be negligible in comparison to the total atmospheric deposition (wet plus dry deposition) by other particles. The annual pine pollen flux to Crystal Lake, an oligotrophic seepage lake in the region, was estimated to be 6.5 g m⁻² during 1981. The deposition of total P by pollen to this lake was 5.8 kg a⁻¹, which is 45 % of the external input of total phosphorus. About 60% of the total P in samples of Pinus strobus and P. resinosa was dissolved reactive P, which is readily available for plant uptake. Because P is the limiting nutrient for many lacustrine systems and pine pollen dispersal coincides with the period of phytoplankton blooms in temperate-region lakes, this episodic input of P may represent an important source for seepage lakes whose external inputs are dominated by atmospheric deposition.