Degradation of diuron in aqueous solution by ozonation

Degradation of diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] in aqueous solution and the proposed degradation mechanism of diuron by ozonation were investigated. The factors that affect the degradation efficiency of diuron were examined. The generated inorganic ions and organic acids during the ozonation process were detected. Total organic carbon removal rate and the amount of the released Cl(-) increased with increasing ozonation time, but only 80.0% of the maximum theoretical concentration of Cl(-) at total mineralization was detected when initial diuron concentration was 13.8 mg L(-1). For N species, the final concentrations of NO3(-) and NH4+ after 60 min of reaction time were 0.28 and 0.19 mg L(-1), respectively. The generated acetic acid, formic acid and oxalic acid were detected during the reaction process. The main degradation pathway of diuron by ozonation involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes, leading to small organic species and inorganic species. The degradation efficiency of diuron increased with decreasing initial diuron concentration. Higher pH value, more ozone dosage, additive Na2CO3, additive NaHCO3 and additive H2O2 were all advantageous to improve the degradation efficiency of diuron.     

Degradation of nitrogen containing organic compounds by combined photocatalysis and ozonation

The combination of TiO2-assisted photocatalysis and ozonation in the degradation of nitrogen-containing substrates such as alkylamines, alkanolamines, heterocyclic and aromatic N-compounds has been investigated. A laboratory set-up was designed and the influence of the structure of the N-compound, the TiO2 and ozone concentration on the formation of breakdown products were examined. The experimental results showed that a considerable increase in the degradation efficiency of the N-compounds is obtained by a combination of photocatalysis and ozonation as compared to either ozonation or photocatalysis only. The mineralization of the model substances was monitored by measurements of the TOC and ion-chromatographic determinations of the formed NO2- and NO3-. The temporal changes of concentrations of breakdown products, such as NH4+, short chain alkyl- and alkanolamines were determined by single column ion chromatography (SCIC) and as well as by electrospray mass spectrometry (EI-MS).     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

Degradation of azo dye Procion Red MX-5B by photocatalytic oxidation

The photocatalytic oxidation (PCO) of a monoazo dye Procion Red MX-5B under various physico-chemical conditions was investigated. Degradation of the dye by PCO was enhanced by augmentation in UV intensity, titanium dioxide and hydrogen peroxide concentrations but was inhibited by increase in initial dye concentration. The PCO process was affected by pH in a peculiar way. In the presence of 100 mg/l of TiO2 and the absence of H2O2, the highest reaction rate was observed when the initial pH was 10. With 500 mg/l of TiO2 and 10 mM of H2O2, the reaction was the fastest at initial pH of 3-5. The optimal conditions for the degradation of the dye, at an UV intensity of 17 mW/cm2, were determined to be: TiO2 concentration, 500 mg/l; initial H2O2 concentration, 10 mM; initial pH, 5.0. Monitoring of TOC loss showed that the dye was mineralized by 90% within 80 min under these conditions. Nevertheless, the persistence of a low level of TOC indicated that mineralization was not complete and dead-end product(s) which was (were) resistant to PCO might have accumulated.     

Removal of propham from water by using electro-Fenton technology: kinetics and mechanism

The removal of a carbamate herbicide, propham, from aqueous solution has been carried out by the electro-Fenton process. Hydroxyl radical, a strong oxidizing agent, was generated catalytically and used for the oxidation of propham aqueous solutions. The degradation kinetics of propham evidenced a pseudo-first order degradation. The absolute rate constant of second order reaction kinetics between propham and ()OH was determined as (2.2+/-0.10)x10(9)m(-1)s(-1). The mineralization of propham was followed by the organic carbon (TOC) removal. The optimal Fe(3+) concentration was found as 0.5mM at 300mA. The 94% of initial TOC of 0.25mM propham solution was removed in 8h at the optimal conditions by using the cathode area to solution volume ratio of 3.33dm(-1). The maximum mineralization current efficiency values were obtained at 60mA in the presence of 0.5mM Fe(3+). During the electro-Fenton treatment, several degradation products were formed. These intermediates were identified by using high performance liquid chromatography, liquid chromatography-mass spectrometry, gas chromatography-mass spectrometry and ion chromatography analysis. The identified by-products allowed proposing a pathway for the propham mineralization.     

Ozonation of an azo dye C.I. Remazol Black 5 and toxicological assessment of its oxidation products

The effect of ozonation (20.5 mgl(-1)) on the degradation processes of an azo dye, Remazol Black 5 (RB5; CI) was studied. Conventional parameters such as chemical oxygen demand (COD), total organic carbon (TOC), pH, conductivity, colour removal, biodegradability (BOD(5/28)), and toxic potential of the dye and its degradation products were monitored during the process. The results obtained indicated that ozonation is a highly effective way to remove the colour of a corresponding dye solution. However, a considerable organic load still remained as indicated by high COD and TOC residues. The COD, TOC reductions were about 40% and 25% for 6 h ozonation of 2 gl(-1) RB5 aqueous solution. During the ozonation process the rapid decrease of pH and the sharp increase of conductivity indicated the formation of acidic by-products and small fragments and ions which were identified by high performance ion chromatography. The BOD28 data revealed that first by-products after partial ozonation (10-150 min) of RB5 were more biodegradable than the parent compound and ozonation can enhance the biodegradability of azo dyes. During the first 150 min of total 360 min of oxidation, the formation of first by-products with high toxic potential took place as it could be confirmed by two acute toxicity-screening tests, the bioluminescence test (Vibrio fischerii) and the neutral red cytotoxicity assay (rat hepatoma cells). The significant enhancement of microbial biodegradability after long-term ozonation could also be seen as a decrease of toxic intermediates in correlation with the ozonation time as indicated in BOD28 biological degradation test results.     

Degradation of octylphenol and nonylphenol by ozone - part I: direct reaction

This aqueous reaction between ozone and two alkylphenols (APs), namely octylphenol (OP) and nonylphenol (NP), has been investigated. Both compounds are important endocrine disrupting chemicals, which arise from the biodegradation of alkylphenol ethoxylates and are often found at relatively high concentrations in wastewater effluents. In this paper the results of an experimental study are presented which provide values for the reaction rate constants between molecular ozone and undissociated OP and NP, and overall reaction rate constants for the degradation of the two APs at pH values in the range of 7-9. The kinetic rate constants for OP and NP degradation by molecular ozone were 4.33(+/-0.18) x 10(4) and 3.90(+/-0.10) x 10(4) M(-1) s(-1), and the reaction stoichiometry was similar in both cases and equal to approximately 1.3:1 ([O3]:[AP]). The overall second order reaction rate constants for the two APs increased significantly with increasing pH, which is believed to be mainly due to the increasing influence of indirect radical reaction with increasing pH; this aspect is considered in more detail in a companion paper. A preliminary investigation of the reaction mechanism suggests that an initial product of ozonation is hydroxyl-alkyl phenol.     

Degradation of calcium lignosulfonate using gamma-ray irradiation

Gamma-ray irradiation was proven to be a promising means for the removal of calcium lignosulfonate (CaLS). At a dose rate of 55Gy min(-1), over 90% of CaLS was mineralized to CO(2), H(2)O and sulfates within 3-d irradiation. The degradation of CaLS with the initial CaLS concentrations ranging from 40 to 200mg l(-1) followed zero-order kinetics at the dose rates of 16-150Gy min(-1). The zero-order degradation rate constant was functionally related with irradiation dose rate. Experiments performed with or without addition of radical scavengers demonstrated that the role of *OH was predominant in CaLS degradation and the reductive species made minor contributions to CaLS degradation. Addition of appropriate amounts of H(2)O(2) significantly enhanced the mineralization of CaLS, e.g., addition of 10mM H(2)O(2) at a dose rate of 55Gy min(-1) elevated the mineralization rate constant by five times. The addition of Fenton's reagent to irradiated CaLS solutions facilitated the degradation of CaLS, but no obviously synergistic effect was observed.     

Ozonation of hydrolyzed azo dye reactive yellow 84 (CI).

The combination of chemical and biological water treatment processes is a promising technique to reduce recalcitrant wastewater loads. The key to the efficiency of such a system is a better understanding of the mechanisms involved during the degradation processes. Ozonation has been applied to many fields in water and wastewater treatment. Especially for textile mill effluents ozonation can achieve high color removal, enhance biodegradability, destroy phenols and reduce the chemical oxygen demand (COD). However, little is known about the reaction intermediates and products formed during ozonation. This work deals with the degradation of hydrolyzed Reactive Yellow 84 (Color Index), a widely used azo dye in textile finishing processes with two monochlorotriazine anchor groups. Ozonation of the hydrolyzed dye in ultra pure water was performed in a laboratory scale cylindric batch reactor. Decolorization, determined by measuring the light absorbance at the maximum wavelength in the visible range (400 nm), was almost complete after 60 and 90 min with an ozone concentration of 18.5 and 9.1 mg/l, respectively. The TOC/TOC0 ratio after ozonation was about 30%, the COD was diminished to 50% of the initial value. The BOD5/COD ratio increased from 0.01 to about 0.8. Oxidation and cleavage of the azo group yield nitrate. Cleavage of the sulfonic acid groups of aromatic rings caused increases in the amount of sulfate. Formic acid and oxalic acid were identified as main oxidation products by high performance ion chromatography (HPIC). The concentrations of these major products were monitored at defined time intervals during ozonation.     

Advanced oxidation of a pulp mill bleaching wastewater.

The degradation, by several advanced oxidation reactions, of a pulp mill ECF bleaching effluent, was studied. The initial biodegradability of the organic matter present in the effluent, estimated as the BOD5/COD, was low (0.3). When the effluent was submitted to ozonation and to five different advanced oxidation systems (O3/UV, O3/UV/ZnO, O3/UV/TiO2, O2/UV/ZnO, O2/UV/TiO2), the biodegradability increase significantly. After five minutes of reaction, the O3/UV system appears as the most efficient in to transform the organic matter to more biodegradable forms. A similar effect was observed when the effluent was submitted to an activated sludge treatment. The COD, TOC and toxicity reduction correlated well with the biodegradability enhancement after AOPs treatments.     

紫外光助臭氧化处理活性艳红K-2BP废水研究

以 30 0W高压汞灯为光源 ,研究了紫外光联合臭氧化、单纯臭氧氧化及单纯紫外光照处理 4 0 0mg/L的活性艳红K 2BP废水的可行性。结果表明 :光催化臭氧化可加速有机物的矿化。在同样时间条件下 ,三者氧化能力由大至小为 :UV/O3 >单独O3 >单独UV。运用TOC、紫外 可见光谱 (UV Vis)、毛细管电泳 (CE)等分析技术初步探讨了紫外光催化臭氧化活性艳红K 2BP溶液的降解效果及降解机理。     

Synergistic effects of combination of photolysis and ozonation on destruction of chlorophenols in water.

Synergistic effects including TOC elimination, ozone consumption and microtoxicity reduction for combination of photolysis and ozonation compared to those of direct photolysis and ozonation alone on destruction of chlorophenols including 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol were studied. It was found that the synergistic effects of combination of photolysis and ozonation increased obviously with increasing initial pH of solution to basic pH levels. Results showed that the synergistic effects of photolytic ozonation under the conditions imposed was notable with mineralization rate enlarging more than 100%, oxidation index (OI) decreasing 50%, and microtoxicity being reduced by 30%, indicating that the potentialities of photolytic ozonation compared to direct photolysis and ozonation alone was remarkable for treatment of industrial wastewater containing chlorophenols.     

MnOx／介孔γ-A12O3催化臭氧化降解水中安替比林的研究

以自制的介孔γ-A12O3为载体,通过等体积浸渍法合成了MnOx／介孔γ-A12O3催化剂。采用X射线衍射（XRD）、透射电镜（TEM）以及紫外一可见漫反射（uV—VisDRS）等手段对其进行表征。结果表明,锰氧化物在介孔氧化铝载体上具有较高的分散度,并且锰以多种价态存在。高度分散以及多价态的MnOx能够提高催化臭氧化过程中电荷转移,引起更高的催化活性。MnOx／介孑γ-A12O3催化剂能够有效地提高臭氧对水中安替比林的矿化效果,对含量为10mg／L的安替比林水溶液在反应60min后基本达到完全矿化。     

Light-induced disappearance of nitrite in the presence of iron (III)

Understanding of rapid disappearance of nitrite in natural waters and its impact on nitrogen natural cycling has remained limited. We found that NO2- disappeared rapidly in pH 3.2 aqueous Fe(III) solutions both in sunlight and in 356 nm light. Quantum yields of the NO2- loss at 356 nm were 0.049-0.14 for initial levels of 10-80 microns NO2- and 200 microns Fe(III). The NO2- loss (at 356 nm) followed apparent first-order kinetics. The rate constants were 1.3 x 10(-3) (40 microns NO2-) and 4.1 x 10(-4) s-1 (80 microns NO2-) for 100 microns Fe(III), and 2.3 x 10(-3) (40 microns NO2-) and 7.5 x 10(-4) s-1 (80 microns NO2(-1)) for 200 microns Fe(III) (t1/2 = 8.7, 27.9, 5.1, and 15.3 min, respectively). The rate constants were directly proportional to [Fe(III)]0 and inversely proportional to [NO2-]0. Agreement between the rate constants obtained experimentally and those calculated mechanistically supports the hypothesis that NO2- was oxidized to NO2 by .OH radicals from photolysis of FeOH2+ complexes, and at high [NO2-]0 (e.g., 80 microns) relative to [Fe(III)]0, hydrolysis of NO2 or N2O4 to form NO3- and NO2- could be significant. This study showed that light and Fe(III)-induced oxidation of NO2- (rate = approximately 10(-1)-10(-2) microns s-1) was more rapid than its direct photolysis (rate = approximately 10(-4) microns s-1), and the photolysis could be a significant source of .OH radicals only in cases where the Fe(III) level is much lower than the NO2- level ([Fe(III)]/[NO2-] < 1/80). This study suggests that the light and Fe(III)-induced oxidation of NO2- would be one potential important pathway responsible for the rapid transformation of NO2- in acidic surface waters, especially those affected by acid-mine drainage or volcanic activities. This study also may be of interest for modeling certain acidic atmospheric water environments.     

微气泡曝气O3／H2O2处理RO浓水的效能及影响因素

采用O3／H2O2高级氧化工艺处理炼油厂反渗透（RO）浓水,用溶气泵加压溶气并产生微气泡强化传质,确定装置运行条件,考察气体中臭氧浓度、O3／H2O2初始摩尔比、pH和温度对O3／H2O2处理RO浓水效果的影响,并对RO浓水处理效能进行研究。结果表明,随着气体中臭氧浓度的增加,COD的去除率基本呈线性增加;加入适当量H,0,能提高臭氧氧化RO浓水的效果,O3／H2O2初始摩尔比在0～0．8范围内,COD的去除率先增加后下降,O3／H2O2初始摩尔比为O．5时COD去除率最大;pH从6．84增加到9．01,COD去除率逐渐增大,pH为10．03时COD去除率反而降低;在14～28℃范围内,温度低时,升高温度COD去除率增加较大,温度较高时,升高温度对COD去除率的影响较小。为考察该工艺的稳定性,在H：0：／0,初始摩尔比为O．5、溶液pH为8～9、臭氧浓度为80～100mg／L、温度为10-28℃条件下,对COD为90～140mg／L的RO浓水氧化处理4～10h,出水COD维持在39．9～49．9mg／L,达到《城镇污水处理厂污染物排放标准（GB18918—2002）》中的一级A标准;去除1gCOD消耗031．4～3．3g,消耗0,与H,02的总氧量为2．2～4．4g。     

Kinetics and mechanism of nitrite oxidation by hypochlorous acid in the aqueous phase

The rate coefficient for the reaction of nitrite with hypochlorite and hypochlorous acid has been studied using spectrophotometric measurements. The reaction rate has been determined in a wide range of H(+) concentration (5< or =-log[H(+)]< or =11). The kinetics were carried out as a function of NO(2)(-), H(+) and total hypochlorite ([HOCl](total)=[HOCl]+[ClO(-)]+[ClNO(2)]) concentrations. The observed overall rate law is described by: -d[HClO](T)dt=[a[NO(2)(-)](2)+b[NO(2)(-)]][H(+)](2)c+d[H(+)]+e[NO(2)(-)][H(+)](2)[HOCl](total)At T=298 K and in Na(2)SO(4) at an ionic strength (I=1.00 M), we obtained using a nonlinear fitting procedure: a=(1.83+/-0.36)x10(7) s(-1), b=(1.14+/-0.23)x10(5) Ms(-1), c=(1.12+/-0.17)x10(-13) M, d=(1.43+/-0.29)x10(-6) M(2) and e=(1.41+/-0.28)x10(3) M where the errors represent 2sigma. According to the overall rate law, a/b=k(1)/k(3), b/e=k(3), c=K(w), d/c=K(a), d=K(a)K(w) and e=K(1)K(a). In Na(2)SO(4) at an ionic strength (I=1.00 M), the values of K(1) and K(a) are (1.1+/-0.1)x10(-4) and 1.28x10(7) M(-1), respectively. A mechanism is proposed for the NO(2)(-) oxidation which involves the reversible initial step: NO(2)(-)+HOCl left harpoon over right harpoon ClNO(2)+OH(-) (K(1)), while ClNO(2) undergoes the two parallel reactions: attack by NO(2)(-) (k(1)) and hydrolysis (k(3)). ClNO(2) and N(2)O(4) are proposed as important intermediates as they control the mechanism. The rate coefficients k(1) and k(3) have been determined at different ionic strengths in NaCl and Na(2)SO(4). The influence of the ionic strength and ionic environment has been studied in this work.     

Rapid reductive dechlorination of atrazine by zero-valent iron under acidic conditions

The dechlorination of atrazine (2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine) via reaction with metallic iron under low-oxygen conditions was studied using reaction mixture pH values of 2.0, 3.0, and 3.8. The pH control was achieved through addition of sulfuric acid throughout the duration of the reaction. The lower the pH of the reaction mixture, the faster the degradation of atrazine. The surface area of the sulfuric acid-treated iron particles was 0.31 (+/- 0.01) m2 g-1 and the surface area normalized initial pseudo-first order rate constants (kSA, where rate = kSA x (surface area/l) x [Atrazine]) at pH values of 2.0, 3.0, and 3.8 were equal to, respectively, 3.0 (+/- 0.4) x 10(-3) min-1 m-2 l, 5 (+/- 3) x 10(-4) min-1 m-2 l, and 1 (+/- 1) x 10(-4) min-1 m-2 l. The observed products of the degradation reaction were dechlorinated atrazine (2-ethylamino-4-isopropylamino-1,3,5-triazine) and possibly hydroxyatrazine (2-ethylamino-4-isopropylamino-6-hydroxy-s-triazine). Triazine ring protonation may account, at least in part, for the observed effect of pH on atrazine dechlorination via metallic iron.     

Processes controlling the distribution and natural attenuation of dissolved phenolic compounds in a deep sandstone aquifer

Processes controlling the distribution and natural attenuation (NA) of phenol, cresols and xylenols released from a former coal-tar distillation plant in a deep Triassic sandstone aquifer are evaluated from vertical profiles along the plume centerline at 130 and 350 m from the site. Up to four groups of contaminants (phenols, mineral acids, NaOH, NaCl) form discrete and overlapping plumes in the aquifer. Their distribution reflects changing source history with releases of contaminants from different locations. Organic contaminant distribution in the aquifer is determined more by site source history than degradation. Contaminant degradation at total organic carbon (TOC) concentrations up to 6500 mg l(-1) (7500 mg l(-1) total phenolics) is occurring by aerobic respiration NO3-reduction, Mn(IV)-/Fe(III)-reduction, SO4-reduction, methanogenesis and fermentation, with the accumulation of inorganic carbon, organic metabolites (4-hydroxybenzaldehyde, 4-hydroxybenzoic acid), acetate, Mn(II), Fe(II), S(-II), CH4 and H2 in the plume. Aerobic and NO3-reducing processes are restricted to a 2-m-thick plume fringe but Mn(IV)-/Fe(II)-reduction, SO4-reduction, methanogenesis and fermentation occur concomitantly in the plume. Dissolved H2 concentrations in the plume vary from 0.7 to 110 nM and acetate concentrations reach 200 mg l(-1). The occurrence of a mixed redox system and concomitant terminal electron accepting processes (TEAPs) could be explained with a partial equilibrium model based on the potential in situ free energy (deltaGr) yield for oxidation of H2 by specific TEAPs. Respiratory processes rather than fermentation are rate limiting in determining the distribution of H2 and TEAPs and H2 dynamics in this system. Most (min. 90%) contaminant degradation has occurred by aerobic and NO3-reducing processes at the plume fringe. This potential is determined by the supply of aqueous O2 and NO3 from uncontaminated groundwater, as controlled by transverse mixing, which is limited in this aquifer by low dispersion. Consumption to date of mineral oxides and SO4 is, respectively, <0.15% and 0.4% of the available aquifer capacity, and degradation using these oxidants is <10%. Fermentation is a significant process in contaminant turnover, accounting for 21% of degradation products present in the plume, and indicating that microbial respiration rates are slow in comparison with fermentation. Under present conditions, the potential for degradation in the plume is very low due to inhibitory effects of the contaminant matrix. Degradation products correspond to <22% mass loss over the life of the plume, providing a first-order plume scale half-life >140 years. The phenolic compounds are biodegradable under the range of redox conditions in the aquifer and the aquifer is not oxidant limited, but the plume is likely to be long-lived and to expand. Degradation is likely to increase only after contaminant concentrations are reduced and aqueous oxidant inputs are increased by dispersion of the plume. The results imply that transport processes may exert a greater control on the natural attenuation of this plume than aquifer oxidant availability.     

Enhanced ozonation of simulated dyestuff wastewater by microbubbles

The ozonation of synthetic wastewater containing azo dye, CI Reactive Black 5, was investigated using a microbubble generator and a conventional bubble contactor. The microbubble generator produced a milky and high intensity microbubble solution in which the bubbles had a mean diameter of less than 58 microm and a numerical density of more than 2.9 x 10(4) counts ml(-1) at a gas flow rate of less than 0.5 l min(-1). Compared with the bubble contactor, the total mass transfer coefficient was 1.8 times higher and the pseudo-first order rate constant was 3.2-3.6 times higher at the same initial dye concentration of 100 mg l(-1), 230 mg l(-1) and 530 mg l(-1) in the proposed microbubble system. The amount of total organic carbon removed per g of ozone consumed was about 1.3 times higher in the microbubble system than in the bubble contactor. The test using terephthalic acid as the chemical probe implied that more hydroxyl radicals were produced in the microbubble system, which contributed to the degradation of the dye molecules. The results suggested that in addition to the enhancement of mass transfer, microbubbles, which had higher inner pressure, could accelerate the formation of hydroxyl radicals and hence improve the oxidation of dye molecules.     

Novel imazethapyr detoxification applying advanced oxidation processes

Different degradation methods have been applied to assess the suitability of advanced oxidation process (AOPs) to promote mineralization of imazethapyr [(RS)-5-ethyl-2-(4-isopropyl-4-methyl-5-oxo-2-imidazolin-2-yl)nicotinic acid], a widely used imidazolinone class herbicide, the persistence of which has been demonstrated in surface and ground waters destined to human uses. Independent of the oxidation process assessed, the decomposition of imazethapyr always followed a pseudo-first order kinetic. The direct UV-irradiation (UV) of the herbicide as well as its oxidation with ozone (O?), and hydrogen peroxide tied to UV-irradiation (H?O?/UV) were sufficiently slow to permit the identification of intermediate products, the formation pathway of which has been proposed. Ozonation joined to UV-irradiation (O?/UV), ozonation joined to titanium dioxide photo-catalysis (TiO?/UV+O?), sole photo-catalysis (TiO?/UV), and photo-catalysis reinforced with hydrogen peroxide-oxidation (TiO?/UV+H?O?) were characterized by a faster degradation and rapid formation of a lot of small molecules, which were quickly degraded to complete mineralization. The most effective oxidation methods were those using titanium dioxide photo-catalysis enhanced either by ozonation or hydrogen peroxide. Most of all, these last processes were useful to avoid the development of dangerous by-products.