Factors affecting degradation of dimethyl sulfoxide (DMSO) by fluidized-bed Fenton process

In this study, the target compound is dimethyl sulfoxide (DMSO), which is used as a photoresist stripping solvent in the semiconductor and thin-film transistor liquid crystal display (TFT-LCD) manufacturing processes. The effects of the operating parameters (pH, Fe²⁺ and H₂O₂ concentrations) on the degradation of DMSO in the fluidized-bed Fenton process were examined. This study used the Box-Behnken design (BBD) to investigate the optimum conditions of DMSO degradation. The highest DMSO removal was 98 % for pH 3, when the H₂O₂ to Fe²⁺ molar ratio was 12. At pH 2 and 4, the highest DMSO removal was 82 %, when the H₂O₂ to Fe²⁺ molar ratio was 6.5. The correlation of DMSO removal showed that the effect of the parameters on DMSO removal followed the order Fe²⁺?>?H₂O₂?>?pH. From the BBD prediction, the optimum conditions were pH 3, 5 mM of Fe²⁺, and 60 mM of H₂O₂. The difference between the experimental value (98 %) and the predicted value (96 %) was not significant. The removal efficiencies of DMSO, chemical oxygen demand (COD), total organic carbon (TOC), and iron in the fluidized-bed Fenton process were higher than those in the traditional Fenton process.     

Enhanced deodorization and sludge reduction in situ by a humus soil cooperated anaerobic/anoxic/oxic (A2O) wastewater treatment system

Simultaneous sludge reduction and malodor abatement in humus soil cooperated an anaerobic/anoxic/oxic (A2O) wastewater treatment were investigated in this study. The HSR-A2O was composed of a humus soil reactor (HSR) and a conventional A2O (designated as C-A2O).The results showed that adding HSR did not deteriorate the chemical oxygen demand (COD) removal, while total phosphorus (TP) removal efficiency in HSR-A2O was improved by 18 % in comparison with that in the C-A2O. Both processes had good performance on total nitrogen (TN) removal, and there was no significant difference between them (76.8 and 77.1 %, respectively). However, NH₄ ⁺–N and NO₃ ^?–N were reduced to 0.3 and 6.7 mg/L in HSR-A2O compared to 1.5 and 4.5 mg/L. Moreover, adding HSR induced the sludge reduction, and the sludge production rate was lower than that in the C-A2O. The observed sludge yield was estimated to be 0.32 kg MLSS/day in HSR-A2O, which represent a 33.5 % reduction compared to a C-A2O process. Activated sludge underwent humification and produced more humic acid in HSR-A2O, which is beneficial to sludge reduction. Odor abatement was achieved in HSR-A2O, ammonium (NH₃), and sulfuretted hydrogen (H₂S) emission decreased from 1.34 and 1.33 to 0.06 mg/m³, 0.025 mg/m³ in anaerobic area, with the corresponding reduction efficiency of 95.5 and 98.1 %. Microbial community analysis revealed that the relevant microorganism enrichment explained the reduction effect of humus soil on NH₃ and H₂S emission. The whole study demonstrated that humus soil enhanced odor abatement and sludge reduction in situ.     

Application of chemical oxidation to remediate HCH-contaminated soil under batch and flow through conditions

This is the first study describing the chemical oxidation of hexachlorocyclohexanes (HCHs) in contaminated soil under water saturated and unsaturated flow through conditions. Soil contaminated with β-HCH (45 mg kg^?1) and γ-HCH (lindane, 25 mg kg^?1) was sampled from former lindane waste storage site. Efficiency of following treatments was tested at circumneutral pH: H₂O₂ alone, H₂O₂/Fe^II, Na₂S₂O₈ alone, Na₂S₂O₈/Fe^II, and KMnO₄. Experimental conditions (oxidant dose, liquid/solid ratio, and soil granulometry) were first optimized in batch experiments. Obtained results revealed that increasing dose of H₂O₂ improved the oxidation efficiency while in Na₂S₂O₈ system, maximum HCHs were removed at 300 mM. However, oxidation efficiency was slightly improved by Fe^II-activation. Increasing the solid/liquid ratio decreased HCH removal in soil samples crushed to 500 μm while an opposite trend was observed for 2-mm samples. Dynamic column experiments showed that oxidation efficiency followed the order KMnO₄ > Na₂S₂O₈/Fe^II > Na₂S₂O₈ whatever the flow condition, whereas the removal extent declined at higher flow rate (e.g., ~50% by KMnO₄ at 0.5 mL/min as compared to ~30% at 2 mL/min). Both HCH removal and oxidant decomposition extents were found higher in saturated columns than the unsaturated ones. While no significant change in relative abundance of soil mineral constituents was observed before and after chemical oxidation, more than 60% of extractable organic matter was lost after chemical oxidation, thereby underscoring the non-selective behavior of chemical oxidation in soil. Due to the complexity of soil system, chemical oxidation has rarely been reported under flow through conditions, and therefore our findings will have promising implications in developing remediation techniques under dynamic conditions closer to field applications.     

Chemical oxidation of cable insulating oil contaminated soil

Leaking cable insulating oil is a common source of soil contamination of high-voltage underground electricity cables in many European countries. In situ remediation of these contaminations is very difficult, due to the nature of the contamination and the high concentrations present. Chemical oxidation leads to partial removal of highly contaminated soil, therefore chemical oxidation was investigated and optimized aiming at a subsequent bioremediation treatment. Chemical oxidation of cable oil was studied with liquid H₂O₂ and solid CaO₂ as well as permanganate at pH 1.8, 3.0 and 7.5. Liquid H₂O₂ most effectively removed cable oil at pH 7.5 (24%). At pH 7.5 poor oil removal of below 5% was observed with solid CaO₂ and permanganate within 2 d contact time, whereas 18% and 29% was removed at pH 1.8, respectively. A prolonged contact time of 7 d showed an increased oil removal for permanganate to 19%, such improvement was not observed for CaO₂.Liquid H₂O₂ treatment at pH 7.5 was most effective with a low acid use and was best fit to a subsequent bioremediation treatment. To further optimize in situ chemical oxidation with subsequent bioremediation the effect of the addition of the iron catalyst and a stepwise liquid H₂O₂ addition was performed. Optimization led to a maximum of 46% cable oil removal with 1469 mM of H₂O₂, and 6.98 mM Fe(II) chelated with citric acid (H₂O₂:FeSO₄ = 210:1 (mol mol⁻¹). The optimum delivery method was a one step addition of the iron catalyst followed by step wise addition of H₂O₂.     

Preparation of petroleum-degrading bacterial agent and its application in remediation of contaminated soil in Shengli Oil Field,China

Two petroleum-degrading strains were screened from oil fields and denoted as SWH-1 (Bacillus subtilis) and SWH-2 (Sphingobacterium multivorum), which were used to ferment and prepare bacterial agent to remediate petroleum-contaminated sites in Shengli Oil Field in China. The optimal liquid fermentation medium and conditions were MgSO₄·7H₂O (0.5 %), NaCl (0.5 %), soybean dregs (3 %), pH 7.0, culturing at 30 °C, and 220 r/min for 16 h. Peat was chosen as the bacterial carrier due to its ability of keeping microbial activity. Mixed fermented liquid was added into peat (1:2) and air-dried, and the bacterial agent was obtained. It was applied to the petroleum-contaminated soil, which was irrigated, tilled, and fertilized. The removal rate reached 67.7 % after 2 months of remediation. During remediation, the quantity of indigenous bacteria varied a lot, while the inoculated bacteria remained stable; the dehydrogenase activity was at high levels and then decreased. Indigenous microorganisms, inoculated bacterial agent, nutrients, water, and soil permeability all played important roles. The study prepared an environment-friendly bacterial agent and established a set of bioremediation technique, which provided further insights into integration of fermentation engineering and soil remediation engineering.     

Combined UV-C/H2O2-VUV processes for the treatment of an actual slaughterhouse wastewater

In this study, a three-factor, three-level Box-Behnken design with response surface methodology were used to maximize the TOC removal and minimize the H₂O₂ residual in the effluent of the combined UV-C/H₂O₂-VUV system for the treatment of an actual slaughterhouse wastewater (SWW) collected from one of the meat processing plants in Ontario, Canada. The irradiation time and the initial concentrations of total organic carbon (TOC_o) and hydrogen peroxide (H₂O_2o) were the three predictors, as independent variables, studied in the design of experiments. The multiple response approach was used to obtain desirability response surfaces at the optimum factor settings. Subsequently, the optimum conditions to achieve the maximum percentage TOC removal of 46.19% and minimum H₂O₂ residual of 1.05% were TOC_o of 213 mg L^?1, H₂O_2o of 450 mg L^?1, and irradiation time of 9 min. The attained optimal operating conditions were validated with a complementary test. Consequently, the TOC removal of 45.68% and H₂O₂ residual of 1.03% were achieved experimentally, confirming the statistical model reliability. Three individual processes, VUV alone, VUV/H₂O₂, and UV-C/H₂O₂, were also evaluated to compare their performance for the treatment of the actual SWW using the optimum parameters obtained in combined UV-C/H₂O₂-VUV processes. Results confirmed that an adequate combination of the UV-C/H₂O₂-VUV processes is essential for an optimized TOC removal and H₂O₂ residual. Finally, respirometry analyses were also performed to evaluate the biodegradability of the SWW and the BOD removal efficiency of the combined UV-C/H₂O₂-VUV processes.     

Examination of oxygen release from plants in constructed wetlands in different stages of wetland plant life cycle

The quantification of oxygen release by plants in different stages of wetland plant life cycle was made in this study. Results obtained from 1 year measurement in subsurface wetland microcosms demonstrated that oxygen release from Phragmites australis varied from 108.89 to 404.44 mg O₂/m²/d during the different periods from budding to dormancy. Plant species, substrate types, and culture solutions had a significant effect on the capacity of oxygen release of wetland plants. Oxygen supply by wetland plants was estimated to potentially support a removal of 300.37 mg COD/m²/d or 55.87 mg NH₄-N/m²/d. According to oxygen balance analysis, oxygen release by plants could provide 0.43–1.12 % of biochemical oxygen demand in typical subsurface-flow constructed wetlands (CWs). This demonstrates that oxygen release of plants may be a potential source for pollutants removal especially in low-loaded CWs. The results make it possible to quantify the role of plants in wastewater purification.     

Atrazine degradation by fungal co-culture enzyme extracts under different soil conditions

This investigation was undertaken to determine the atrazine degradation by fungal enzyme extracts (FEEs) in a clay-loam soil microcosm contaminated at field application rate (5 μg g^?1) and to study the influence of different soil microcosm conditions, including the effect of soil sterilization, water holding capacity, soil pH and type of FEEs used in atrazine degradation through a 2⁴ factorial experimental design. The Trametes maxima–Paecilomyces carneus co-culture extract contained more laccase activity and hydrogen peroxide (H₂O₂) content (laccase = 18956.0 U mg protein^?1, H₂O₂ = 6.2 mg L^?1) than the T. maxima monoculture extract (laccase = 12866.7 U mg protein^?1, H₂O₂ = 4.0 mg L^?1). Both extracts were able to degrade atrazine at 100%; however, the T. maxima monoculture extract (0.32 h) achieved a lower half-degradation time than its co-culture with P. carneus (1.2 h). The FEE type (p = 0.03) and soil pH (p = 0.01) significantly affected atrazine degradation. The best degradation rate was achieved by the T. maxima monoculture extract in an acid soil (pH = 4.86). This study demonstrated that both the monoculture extracts of the native strain T. maxima and its co-culture with P. carneus can efficiently and quickly degrade atrazine in clay-loam soils.     

Accumulation and spatial distribution of Cd, Cr, and Pb in mulberry from municipal solid waste compost following application of EDTA and (NH4)2SO4

Municipal solid waste compost can be used to cropland as soil amendment to supply nutrients and improve soil physical properties. But long-term application of municipal solid waste (MSW) compost may result in accumulation of toxic metals in amended soil. Phytoremediation, especially phytoextraction, is a novel, cost-effective, and environmentally friendly approach that uses metal-accumulating plants to concentrate and remove metals from contaminated soils. Ethylenediaminetetraacetate (EDTA) was applied to metal-contaminated soil to increase the mobility and phytoavailability of metals in soil, thereby increasing the amount of toxic metals accumulated in the upper parts of phytoextracting plants. The objectives of this study were (1) to investigate the accumulation and spatial distribution of toxic metals (Cd, Cr, and Pb) in mulberry from MSW compost with the application of EDTA and (NH₄)₂SO₄, (2) to examine the effectiveness of EDTA and (NH₄)₂SO₄ applied together on toxic metals (Cd, Cr, and Pb) removal by mulberry under field conditions, and (3) to evaluate the potential of mulberry for phytoextraction of toxic metals from MSW compost. The tested plant—mulberry had been grown in MSW compost field for 4 years. EDTA solution at five rates (0, 50, 100, 50 mmol L^?1?+?1 g?L^?1 (NH₄)₂SO₄, and 100 mmol L^?1?+?1 g?L^?1 (NH₄)₂SO₄) was added into mulberry root medium in September 2009. Twenty days later, the plants were harvested and separated into six parts according to plant height. Cd, Cr, and Pb contents in plant samples and MSW compost were analyzed using an atomic absorption spectrophotometer. In the same treatment, Cd, Cr, and Pb concentrations in mulberry shoot were all higher than those in root, and Cd and Pb concentrations in shoot increased from lower to upper parts, reaching the highest in leaves. Significant increases were found in toxic metal concentration in different parts of mulberry with increasing EDTA concentration, especially when combined with (NH₄)₂SO₄. Mulberry exhibited high ability to accumulate Cd with bioconcentration factors (BCFs) higher than 1. EDTA application also significantly increased Cd BCFs. More than 30 % of metal uptake was concentrated in mulberry branches (stem of above 100 cm height) and leaves. Results presented here show that mulberry is a woody plant that has the potential of Cd phytoextraction from MSW compost by removing leaves and cutting branches. The application of EDTA combined with (NH₄)₂SO₄ significantly enhanced the efficiency of mulberry in removing Cd from the compost medium. Adding (NH₄)₂SO₄ into the compost will lower the risk of the exposure of environment to excessive non-biodegradable EDTA in a large-scale EDTA-assisted phytoextraction by reducing the dosage of EDTA. In China, the need for sod is increasing day by day. Sod is often produced on arable soil and sold together with soils. This would lead to the soil being infertile and the soil layer thin. After several times’ production, the soil can no longer be used for cultivating crops and be destroyed. In order to fully utilize MSW compost resources and save valuable soil resources, MSW compost can be used to replace arable soil to produce sod after extraction of toxic metals in it.     

Application of the Fenton’s process in a bubble column reactor for hydroquinone degradation

The aim of this study was to assess the degradation and mineralization of hydroquinone (HQ) by the Fenton’s process in a bubble column reactor (BCR). The effect of the main operating variables, namely, air flow rate, effluent volume, hydrogen peroxide (H₂O₂) concentration, catalyst (Fe²⁺) dose, initial pH, and temperature, were assessed. For all air flow rates tested, no concentration gradients along the column were noticed, evidencing that a good mixing was reached in the BCR. For the best conditions tested ([H₂O₂] = 500 mg/L, [Fe²⁺] = 45 mg/L, T = 24 °C, Q _air = 2.5 mL/min, pH = 3.0, and V = 5 L), complete HQ degradation was reached, with ~ 39% of total organic carbon (TOC) removal, and an efficiency of the oxidant use—η _H2O2—of 0.39 (ratio between TOC removed per H₂O₂ consumed normalized by the theoretical stoichiometric value); moreover, a non-toxic effluent was generated. Under these conditions, the intermediates and final oxidation compounds identified and quantified were a few carboxylic acids, namely, maleic, pyruvic, and oxalic. As a strategy to improve the TOC removal, a gradual dosage of the optimal H₂O₂ concentration was implemented, being obtained ~ 55% of mineralization (with complete HQ degradation). Finally, the matrix effect was evaluated, for which a real wastewater was spiked with 100 mg/L of HQ; no reduction in terms of HQ degradation and mineralization was observed compared to the solution in distilled water.     

The Fate of Hydrogen Peroxide as an Oxygen Source for Bioremediation Activities within Saturated Aquifer Systems

ABSTRACT

In situ bioremediation is an innovative technique for the remediation of contaminated aquifers that involves the use of microorganisms to remediate soils and groundwaters polluted by hazardous substances. During its application, this process may require the addition of nutrients and/or electron acceptors to stimulate appropriate biological activity. Hydrogen peroxide has been commonly used as an oxygen source because of the limited concentrations of oxygen that can be transferred into the groundwater using above-ground aeration followed by reinjection of the oxygenated groundwater into the aquifer or subsurface air sparging of the aquifer. Because of several potential interactions of H₂O₂ with various aquifer material constituents, its decomposition may be too rapid, making effective introduction of the H₂O₂ into targeted treatment zones extremely difficult and costly. Therefore, a bench-scale study was conducted to determine the fate of H₂O₂ within subsurface aquifer environments. The purpose of this investigation was to identify those aquifer constituents, both biotic and abiotic, that are most active in controlling the fate of H₂O₂. The decomposition rates of H₂O₂ were determined using both equilibrated water samples and soil slurries. Results showed H₂O₂ decomposition to be effected by several commonly found inorganic soil components; however, biologically mediated catalytic reactions were determined to be the most substantial.     

Study on biodegradation process of lignin by FTIR and DSC

The biodegradation process of lignin by Penicillium simplicissimum was studied to reveal the lignin biodegradation mechanisms. The biodegradation products of lignin were detected using Fourier transform infrared spectroscopy (FTIR), UV–Vis spectrophotometer, different scanning calorimeter (DSC), and stereoscopic microscope. The analysis of FTIR spectrum showed the cleavage of various ether linkages (1,365 and 1,110 cm^?1), oxidation, and demethylation (2,847 cm^?1) by comparing the different peak values in the corresponding curve of each sample. Moreover, the differences (T_m and ΔH_m values) between the DSC curves indirectly verified the FTIR analysis of biodegradation process. In addition, the effects of adding hydrogen peroxide (H₂O₂) to lignin biodegradation process were analyzed, which indicated that H₂O₂ could accelerate the secretion of the MnP and LiP and improve the enzymes activity. What is more, lignin peroxidase and manganese peroxidase catalyzed the lignin degradation effectively only when H₂O₂ was presented.     

Influence of operational key parameters on the photocatalytic decolorization of Rhodamine B dye using Fe2+/H2O2/Nb2O5/UV system

The present research deals with the development of a new heterogeneous photocatalysis and Fenton hybrid system for the removal of color from textile dyeing wastewater as Rhodamine B (RhB) solutions by using Fe²⁺/H₂O₂/Nb₂O₅ as a photocatalytic system. The application of this photocatalytic system for the decolorization of dye contaminants is not reported in the literature yet. Different parameters like dye concentration, Nb₂O₅/Fe²⁺ catalyst amount, pH, and H₂O₂ concentration have been studied. The optimum conditions for the decolorization of the dye were initial concentration of 10 mg L^?1 of dye, pH 4, and Nb₂O₅/Fe²⁺ catalyst concentration of 0.5 g L^?1/50 mg L^?1. The optimum value of H₂O₂ concentration for the conditions used in this study was 700 mg L^?1. Moreover, the efficiency of the Nb₂O₅/photo-Fenton hybrid process in comparison to photo-Fenton alone and a dark Fenton process as a control experiment to decolorize the RhB solution has been investigated. The combination of photo-Fenton and Nb₂O₅ catalysts has been proved to be the most effective for the treatment of such type of wastewaters. The results revealed that the RhB dye was decolorized in a higher percent (78 %) by the Nb₂O₅/photo-Fenton hybrid process (Fe²⁺/H₂O₂/Nb₂O₅/UV) than by the photo-Fenton process alone (37 %) and dark Fenton process (14 %) after 120 min of treatment. Moreover, the Nb₂O₅ catalyst as a heterogeneous part of the photocatalytic system was demonstrated to have good stability and reusability.     

Assessing the hydrocarbon degrading potential of indigenous bacteria isolated from crude oil tank bottom sludge and hydrocarbon-contaminated soil of Azzawiya oil refinery,Libya

The disposal of hazardous crude oil tank bottom sludge (COTBS) represents a significant waste management burden for South Mediterranean countries. Currently, the application of biological systems (bioremediation) for the treatment of COTBS is not widely practiced in these countries. Therefore, this study aims to develop the potential for bioremediation in this region through assessment of the abilities of indigenous hydrocarbonoclastic microorganisms from Libyan Hamada COTBS for the biotreatment of Libyan COTBS-contaminated environments. Bacteria were isolated from COTBS, COTBS-contaminated soil, treated COTBS-contaminated soil, and uncontaminated soil using Bushnell Hass medium amended with Hamada crude oil (1 %) as the main carbon source. Overall, 49 bacterial phenotypes were detected, and their individual abilities to degrade Hamada crude and selected COBTS fractions (naphthalene, phenanthrene, eicosane, octadecane and hexane) were evaluated using MT2 Biolog plates. Analyses using average well colour development showed that ~90 % of bacterial isolates were capable of utilizing representative aromatic fractions compared to 51 % utilization of representative aliphatics. Interestingly, more hydrocarbonoclastic isolates were obtained from treated contaminated soils (42.9 %) than from COTBS (26.5 %) or COTBS-contaminated (30.6 %) and control (0 %) soils. Hierarchical cluster analysis (HCA) separated the isolates into two clusters with microorganisms in cluster 2 being 1.7- to 5-fold better at hydrocarbon degradation than those in cluster 1. Cluster 2 isolates belonged to the putative hydrocarbon-degrading genera; Pseudomonas, Bacillus, Arthrobacter and Brevundimonas with 57 % of these isolates being obtained from treated COTBS-contaminated soil. Overall, this study demonstrates that the potential for PAH degradation exists for the bioremediation of Hamada COTBS-contaminated environments in Libya. This represents the first report on the isolation of hydrocarbonoclastic bacteria from Libyan COTBS and COTBS-contaminated soil.     

Nitrate removal under different ecological remediation measures in Taihu Lake: a 15 N mass-balance approach

Ecological remediation is an important measure for the protection of lake water quality in removing nutrients, such as nitrate (NO₃ ^?). In this study, four bioremediation processes (bare sediment, immobilized nitrogen cycling bacteria (INCB) added, Elodea nuttallii added, E. nuttallii-INCB assemblage) were operated at a lab to elucidate the effect of macrophyte appearance and INCB addition on NO₃ ^? removal and achieve the optimal processes for biomediation. ¹⁵?N-NO₃ solution was added to microcosms to identify the key nitrogen transformation processes responsible for NO₃ ^? removal. Results showed that nitrate removal was significantly enhanced after the addition of INCB and E. nuttallii. In the treatments with INCB added, E. nuttallii added, and INCB and E. nuttallii-INCB assemblage, nitrate removal ratio achieved 94.74, 98.76, and 99.15 %, respectively. In contrast, only 23.47 % added nitrate was removed in the control. Plant uptake and denitrification played an important role in nitrogen removal. The water quality was substantially improved by the addition of INCB and macrophyte that can accelerate denitrification and promote nitrogen assimilation of plants. The results indicated that plant uptake and microbial denitrification were key processes for nitrate removal.     

Fenton-like degradation of nalidixic acid with Fe3+/H2O2

The Fenton-like degradation of nalidixic acid was studied in this work. The effects of Fe³⁺ concentration and initial H₂O₂ concentration were investigated. Increasing the initial H₂O₂ concentration enhances the degradation and mineralization efficiency for nalidixic acid, while Fe³⁺ shows an optimal concentration of 0.25 mM. A complete removal of nalidixic acid and a TOC removal of 28 % were achieved in 60 min under a reaction condition of [Fe³⁺]?=?0.25 mM, [H₂O₂]?=?10 mM, T?=?35 °C, and pH?=?3. LC–MS analysis technique was used to analyze the possible degradation intermediates. The degradation pathways of nalidixic acid were proposed according to the identified intermediates and the electron density distribution of nalidixic acid. The Fenton-like degradation reaction of nalidixic acid mainly begins with the electrophilic attack of hydroxyl radical towards the C₃ position which results in the ring-opening reaction; meanwhile, hydroxyl radical attacking to the branched alkyl groups of nalidixic acid leads to the oxidation at the branched alkyl groups.     

Elimination of radiocontrast agent diatrizoic acid by photo-Fenton process and enhanced treatment by coupling with electro-Fenton process

The removal of radiocontrast agent diatrizoic acid (DIA) from water was performed using photo-Fenton (PF) process. First, the effect of H₂O₂ dosage on mineralization efficiency was determined using ultraviolet (UV) irradiation. The system reached a maximum mineralization degree of 60 % total organic carbon (TOC) removal at 4 h with 20 mM initial H₂O₂ concentration while further concentration values led to a decrease in TOC abatement efficiency. Then, the effect of different concentrations of Fenton’s reagents was studied for homogeneous Fenton process. Obtained results revealed that 0.25 mM Fe³⁺ and 20 mM H₂O₂ were the best conditions, achieving 80 % TOC removal efficiency at 4 h treatment. Furthermore, heterogeneous PF treatment was developed using iron-activated carbon as catalyst. It was demonstrated that this catalyst is a promising option, reaching 67 % of TOC removal within 4 h treatment without formation of iron leachate in the medium. In addition, two strategies of enhancement for process efficiency are proposed: coupling of PF with electro-Fenton (EF) process in two ways: photoelectro-Fenton (PEF) or PF followed by EF (PF-EF) treatments, achieving in both cases the complete mineralization of DIA solution within only 2 h. Finally, the Microtox tests revealed the formation of more toxic compounds than the initial DIA during PF process, while, it was possible to reach total mineralization by both proposed alternatives (PEF or PF-EF) and thus to remove the toxicity of DIA solution.     

Synthesis of Fe-doped Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocatalyst and its sonophotocatalytic activity on synthetic dye and real textile wastewater

The catalysts such as Fe, Bi₂O₃, and Fe-doped Bi₂O₃ were synthesized for the sonophotocatalytic treatment of synthetic dye and real textile wastewater. The resultant catalysts were characterized for its size and uniform shape using x-ray diffractogram (XRD) and scanning electron microscopy (SEM) which signified the nanorod shape formed Bi₂O₃. The higher ultraviolet light absorbance capacity of the catalysts was also evident using diffuse reflectance spectroscopy (DRS). Initially, the effect of conventional parameters such as initial pH, gas bubbling (argon, oxygen, air and nitrogen) and oxidant addition (H₂O₂ and peroxymonosulfate) in the presence of sonolysis (22 and 37 kHz frequency) and photolysis (UV-C light) on 10 ppm Basic Brown 1 dye was studied. The results showed that highest decolorization of 62 % was attained for 3 g/L peroxymonosulfate under 37 kHz frequency sonolysis treatment. Secondly, with the catalyst study, highest of 46 % dye color removal was obtained with 4 g/L Fe under 37 kHz frequency sonolysis treatment. The sonophotocatalytic treatment of dye with Fe-doped Bi₂O₃ catalyst in combination with peroxymonosulfate showed highest color removal of 99 %. Finally, the sonophotocatalytic treatment of real textile wastewater in the presence of 3 g/L Fe-doped Bi₂O₃ and 6 g/L peroxymonosulfate reduced the total organic carbon (TOC) and chemical oxygen demand (COD) level to 77 and 91 %, respectively, in 180 min. The reported treatment process was found to treat the synthetic dye and real textile wastewater effectively.     

Assessment of crude oil biodegradation in arctic seashore sediments: effects of temperature,salinity, and crude oil concentration

The expected increase in offshore oil exploration and production in the Arctic may lead to crude oil spills along arctic shorelines. To evaluate the potential effectiveness of bioremediation to treat such spills, oil spill bioremediation in arctic sediments was simulated in laboratory microcosms containing beach sediments from Barrow (Alaska), spiked with North Slope Crude, and incubated at varying temperatures and salinities. Biodegradation was measured via respiration rates (CO₂ production); volatilization was quantified by gas chromatography/mass spectrophotometry (GC/MS) analysis of hydrocarbons sorbed to activated carbon, and hydrocarbons remaining in the sediment were quantified by GC/flame ionization detector (FID). Higher temperature leads to increased biodegradation by naturally occurring microorganisms, while the release of volatile organic compounds was similar at both temperatures. Increased salinity had a small positive impact on crude oil removal. At higher crude oil dosages, volatilization increased, however CO₂ production did not. While only a small percentage of crude oil was completely biodegraded, a larger percentage was volatilized within 6–9 weeks.     

Electrooxidation of industrial wastewater containing 1,4-dioxane in the presence of different salts

The treatment of 1,4-dioxane solution by electrochemical oxidation on boron-doped diamond was studied using a central composite design and the response surface methodology to investigate the use of SO₄ ^2? and HCO₃ ^? as supporting electrolytes considering the applied electric current, initial chemical oxygen demand (COD) value, and treatment time. Two industrial effluents containing bicarbonate alkalinity, one just carrying 1,4-dioxane (S1), and another one including 1,4-dioxane and 2-methyl-1,3-dioxolane (S2), were treated under optimized conditions and subsequently subjected to biodegradability assays with a Pseudomonas putida culture. Electrooxidation was compared with ozone oxidation (O₃) and its combination with hydrogen peroxide (O₃/H₂O₂). Regarding the experimental design, the optimal compromise for maximum COD removal at minimum energy consumption was shown at the maximum tested concentrations of SO₄ ^2? and HCO₃ ^? (41.6 and 32.8 mEq L^?1, respectively) and the maximum selected initial COD (750 mg L^?1), applying a current density of 11.9 mA cm^?2 for 3.8 h. Up to 98 % of the COD was removed in the electrooxidation treatment of S1 effluent using 114 kWh per kg of removed COD and about 91 % of the COD from S2 wastewater applying 49 kWh per kg of removed COD. The optimal biodegradability enhancement was achieved after 1 h of electrooxidation treatment. In comparison with O₃ and O₃/H₂O₂ alternatives, electrochemical oxidation achieved the fastest degradation rate per oxidant consumption unit, and it also resulted to be the most economical treatment in terms of energy consumption and price per unit of removed COD.