挥发性溴代消毒副产物在不同水处理工艺过程中的变化

对中国沿海某市2个自来水厂的常规和深度水处理工艺过程中挥发性溴代消毒副产物的变化规律进行了研究。在选取的7种挥发性溴代消毒副产物中,只有一溴二氯甲烷、二溴一氯甲烷、二溴甲烷和三溴甲烷这4种被检出,除二溴甲烷只在深度水处理工艺过程中被检出外,其余3种化合物在2种不同水处理工艺过程中均有检出。一溴二氯甲烷和二溴一氯甲烷在常规和深度水处理工艺过程中的部分工艺段出水中的检出浓度超过了GB 5749-2006中规定的限值（饮用水中一溴二氯甲烷和二溴一氯甲烷的的浓度限值分别为60 μg·L-1和100 μg·L-1）,应被给予足够的重视。挥发性溴代消毒副产物在常规水处理工艺过程中的检出浓度随水处理工艺流程而逐渐升高,而在深度水处理工艺过程中检出的挥发性溴代消毒副产物（除二溴甲烷外）浓度变化则表现为随水处理工艺流程先轻微降低后大幅升高的趋势。与常规水处理工艺相比,挥发性溴代消毒副产物在深度水处理工艺过程中的检出浓度明显低于其在常规水处理工艺过程中对应工艺段出水中的检出浓度,但对于在常规和深度水处理工艺过程中均被检出的3种挥发性溴代消毒副产物来说,它们的最大值均出现在加氯后出厂水中。     

臭氧对饮用水中氯化消毒副产物生成的影响

以北京市某水厂砂滤池出水为实验原水,研究了臭氧曝气时间对实验原水中天然有机物（NOM）性质、结构及氯化消毒副产物生成的影响。通过高效凝胶色谱、三维荧光光谱、红外光谱等检测分析方法对水中NOM进行表征后发现,经臭氧作用后水样DOC浓度升高、亲水性增加、芳香性及重均分子量下降。有机物中羟基、碳碳双键或碳氮双键及其共轭体系、脱质子羧基官能团与氯反应活性较强。综合考虑臭氧作用后NOM性质、结构变化及氯化消毒副产物生成量的改变,选择最佳臭氧接触时间为12 min。     

饮用水臭氧氧化处理过程中溴酸根的产生及控制

论述了给水处理中溴酸根（BrO3-）的健康危害、产生机理、影响因素及其控制和去除方法。采用臭氧氧化处理含溴离子（Br-）水时,会产生以BrO3-为主的臭氧化副产物。BrO3-的生成与Br-初始浓度、臭氧投加量、水温、无机碳浓度、水中天然有机物（NOM）的种类和浓度、以及水的pH值等因素有关。目前研究较多的削减BrO3-...     

Formation of disinfection by-products in chlorinated swimming pool water.

The formation of five volatile disinfection by-products (DBPs: chloroform, bromodichloromethane, chloral hydrate, dichloroacetonitrile, and 1,1,1-trichloropropanone) by the chlorination of the materials of human origin (MHOs: hair, lotion, saliva, skin, and urine) in a swimming pool model system was examined. Chlorination reactions took place with a sufficient supply of chlorine residuals (0.84 mg Cl2/l < total chlorine < 6.0 mg Cl2/l) in 300 ml glass bottles containing either ground water or surface water as a reaction medium at 30 degrees C and pH 7.0, for either 24 or 72 h. A longer reaction period of 72 h or a higher content of organic materials led to the increased formation of DBPs. Of the DBPs formed by the reaction, chloroform was a major compound found in both ground and surface waters. The formation of chloroform and bromodichloromethane per unit total organic carbon (TOC) concentration was suppressed when all types of MHOs were added to the surface water that already contained DBP precursors such as humic substances. However, the formation of dichloroacetonitrile was promoted, probably due to the increased degradation reactions of nitrogen-containing compounds such as urea and proteins of human origin. In conclusion, the materials of swimmers' origin including hair, lotion, saliva, skin, and urine add to the levels of DBPs in swimming pool water, and any mitigation measures such as periodic change of water are needed to protect swimmers from elevated exposures to these compounds.     

Formation of chlorinated disinfection by-products in viticulture

Background, aim and scope  The use of sodium hypochlorite (HYP) in viticulture results in effluents which are contaminated with halogenated substances. These disinfection by-products (DBPs) can be quantified as group parameter ‘adsorbable organic halogens’ (AOX) and have not been determined in effluents of viticulture yet. The substances that are detected as AOX are unknown. The AOX can be composed of harmless substances, but even toxic contaminants. Thus, it is impossible to assess ecological impacts. The aim of this study is to determine the quantification of AOX and DBPs after the use of HYP. This will be helpful to reduce environmental pollution by AOX. Materials and methods  The potential of HYP to generate AOX was determined in laboratory-scale experiments. Different model solutions were treated with HYP according to disinfection processes in viticulture and conditions of AOX formation in effluents were simulated. AOX were quantified using the flask-shaking method and identified DBPs were investigated by gas chromatography–mass spectrometry. Results  Treatment with HYP resulted in the formation of AOX. The percentage conversion of HYP to AOX was up to 11%. Most important identified DBPs in viticulture are chloroform, dichloroacetic acid and trichloroacetaldehyde. In addition, the formation of carbon tetrachloride (CT), 1,1,1-trichloropropanone, 2,4-dichlorobenzoic acid and 2-chloro-/2,4-dichlorophenylacetic acid was investigated. It was demonstrated that reaction temperature, concentration of HYP and type of organic matter have important influence on the formation of chlorinated DBPs. Discussion  The percentage conversion of HYP to AOX was similar to other published studies. Although a correlation of single compounds and AOX is difficult, chloroform was the predominant AOX. Generation of the volatile chloroform should be avoided due to possible adverse effects. The generation of dichloroacetic acid is of minor importance on account of biodegradation. Trichloroacetaldehyde and 1,1,1-trichloropropanone are weak mutagens and their formation should be avoided. Conclusions  The generation of AOX and chlorinated DBPs can be minimised by reducing the concentrations of the organic materials in the effluents. The removal of organic matter before disinfection results in a decreased formation of AOX. HYP is an effective disinfectant; therefore, it should be used at low temperatures and concentrations to reduce the amount of AOX. If possible, disinfection should be accomplished by the use of no chlorine-containing agents. By this means, negative influences of HYP on the quality of wine can also be avoided. Recommendations and perspectives  Our results indicate that HYP has a high potential to form AOX in effluents of viticulture. The predominant by-products are chloroform, dichloroacetic acid and trichloroacetaldehyde. In further research, wastewaters from a winery and the in- and outflows of two sewage treatment plants were sampled during vintage and analysed. These results will be discussed in a following paper.     

Formation of nitrogenous disinfection by-products from pre-chloramination

A sampling survey investigated the formation of nitrogenous disinfection by-products (N-DBPs) and carbonaceous DBPs (C-DBPs) from pre-chloramination, an increasingly common treatment strategy in China for regulated C-DBP control, followed by subsequent conventional water treatment processes, i.e., coagulation, sedimentation, and filtration. Dihalogenated N-DBPs typically peaked in the summer and early autumn with a relatively higher temperature, with the maximum levels of dichloroacetamide (DCAcAm), dichloroacetonitrile (DCAN), bromochloroacetonitrile, dibromoacetonitrile and dichloroacetone at 1.8, 6.3, 6.0, 2.6 and 1.8 μg L⁻¹ in the finished water, respectively. Also, the levels of all the dichlorinated N-DBPs were correlated with the ratio of dissolved organic nitrogen (DON) to dissolved organic carbon, implying autochthonous DON played an essential role in the formation of these DBPs. In contrast, the yields of trihalogenated DBPs [chloroform (CF), trichloronitromethane (TCNM) and trichloroacetone (TCAce)] appeared not to be significantly affected by seasons. CF and DCAN were the dominant species in trihalomethanes (THMs) and dihaloacetonitriles (DHANs), respectively. Bromine was more readily incorporated into DHANs to form brominated DBPs than THMs during pre-chloramination. Although pre-chloramination can ensure the finished water to meet with the current Chinese THM regulatory limits, the increased levels of TCNM and TCAce may be a new water quality concern.     

Effects of bromide and iodide ions on the formation of disinfection by-products during ozonation and subsequent chlorination of water containing biological source matters

This study aims to investigate the influence of the coexistence of halogen ions (bromide/iodide) and biological source matters on the speciation and yield of trihalomethanes (THMs), haloacetic acids (HAAs), and N-nitrosodimethylamine (NDMA) during the ozonation and subsequent chlorination of water. The results show that the concentrations of brominated THMs and iodinated THMs increased with increasing bromide and iodide concentration. These results may be attributed to the higher reactivity of hypobromous acid and hypoiodous acid generated from the ozonation and subsequent chlorination in the presence of bromide or iodide ions. The presence of bromide increased the species of brominated HAAs. There was a shift from chlorinated HAAs to brominated HAAs after increasing the concentration of bromide. The effect of iodide on HAA formation was more complex than bromide. For most samples, the concentration of total HAAs (T-HAAs) increased to the maximum and then decreased with increasing iodide concentration. The components of the organic precursors also significantly influenced the formation of brominated and iodinated disinfection by-products (Br-DBPs and I-DBPs). Humic acids produced more CHBr₃ (596.60 μg/L) than other organic materials. Microcystis aeruginosa cells produced the most tribromoacetic acid (TBAA, 84.16 μg/L). Furthermore, the yield of NDMA decreased with increasing bromide concentration, indicating that the formation of NDMA was inhibited by the high concentration of bromide.     

多水源供水管网中消毒副产物风险分析

通过调研北方某大型城市多水源供水格局下管网水中三卤甲烷(THMs)和卤乙酸(HAAs)这2类消毒副产物(DBPs)的质量浓度水平,对管网中各类DBPs的超标风险、风险点的时空分布及影响因素进行了分析,从确定管网指示性DBPs、检测频率及管网采样点布设3个方面提出了关于管网DBPs风险分析方法的建议.研究结果表明,该市D...     

Formation of oxidation by-products of the iodinated X-ray contrast medium iomeprol during ozonation

The present work describes the investigation of the formation of oxidation by-products of the iodinated X-ray contrast medium (ICM) iomeprol during ozonation in water treatment. Bench-scale investigations revealed that ICM can be partly oxidized during ozonation processes, whereas the ionic diatrizoic acid showed the lowest reactivity. Iomeprol, as a representative of ICM, was not fully mineralized during ozonation. Thus, unknown oxidation by-products were formed. Aqueous solutions of iomeprol were treated by ozonation in order to assess the formation of oxidation by-products. The by-products were characterized by different liquid chromatography methods including detection of single-stage mass spectra, product ion mass spectra, and induced in-source fragmentation for analysis of iodine containing oxidation by-products. Aldehyde and carbonyl containing compounds were proposed to be among the stable by-products. A derivatization step confirms that the aldehyde and carbonyl moieties are major functional groups in oxidation by-products of iomeprol. Furthermore, oxidation by-products of iomeprol were detected at the outlet of an ozone reactor at a full-scale waterworks. However, the toxicological relevance of the by-products is a major future research tasks.     

Fate of disinfection by-products in groundwater during aquifer storage and recovery with reclaimed water

Knowledge on the behaviour of disinfection by-products (DBPs) during aquifer storage and recovery (ASR) is limited even though this can be an important consideration where recovered waters are used for potable purposes. A reclaimed water ASR trial in an anoxic aquifer in South Australia has provided some of the first quantitative information at field-scale on the fate and transport of trihalomethanes (THMs) and haloacetic acids (HAAs). The results revealed that THM half-lives varied from <1 to 65 days, with persistence of chloroform being highest and bromoform lowest. HAA attenuation was rapid (<1 day). Rates of THM attenuation were shown to be highly dependent on the geochemical environment as evidenced by the 2-5 fold reduction in half-lives at the ASR well which became methanogenic during the storage phase of the trial, as compared to an observation well situated 4 m away, which remained nitrate-reducing. These findings agree with previous laboratory-based studies which also show persistence declining with increased bromination of THMs and reducing redox conditions. Modelling suggests that the chlorinated injectant has sufficient residual chlorine and natural organic matter for substantial increases in THMs to occur within the aquifer, however this is masked in some of the field observations due to concurrent attenuation, particularly for the more rapidly attenuated brominated compounds. The model is based on data taken from water distribution systems and may not be representative for ASR since bromide and ammonia concentrations in the injected water and the possible role of organic carbon in the aquifer were not taken into consideration. During the storage phase DBP formation potentials were reduced as a result of the removal of precursor material despite an increase in the THM formation potential per unit weight of total organic carbon. This suggests that water quality improvements with respect to THMs and HAAs can be achieved through ASR in anoxic aquifers.     

The occurrence of disinfection by-products in the drinking water of Athens,Greece

Application of chlorination for the disinfection of drinking water results in the formation of a wide range of organic compounds, called disinfection by-products (DBPs), which occur due to the reaction of chlorine with natural organic materials. The occurrence of DBPs was studied in samples from four drinking-water treatment plants (WTPs) and from the distribution network of Athens, Greece. Twenty-four compounds, which belong to different categories of DBPs, were monitored, including trihalomethanes (THMs), haloacetic acids (HAAs), haloacetonitriles (HANs), haloketones (HAKs), chloral hydrate (CH) and chloropicrin (CP). Sampling was performed monthly for a period of two years, from three different points at each WTP and from eight points atthe distribution network. Samples were analyzed by GC-ECD methods, which included pretreatment with liquid-liquid extraction for volatile DBPs and acidic methanol esterification for HAAs. The results of the analyses have shown the presence of disinfection by-products belonging to all categories studied in all water samples collected after prechlorination. The major categories of DBPs detected were THMs and HAAs, while the other volatile DBPs occurred at lower concentrations. The concentrations of DBPs did not in any case exceed the maximum contaminant levels (MCL) set by USEPA and WHO. However, monitoring these compounds needs to be continued, because their levels could increase due to changes in the quality of water entering the water treatment plants. Reduction of the concentrations of DBPs could be achieved by optimization of the chlorination conditions, taking into account the effect of time. Moreover, research on alternative disinfection methods (e.g. ozone, chlorine dioxide, chloramines) and their by-products should be conducted to evaluate their applicability in the case of the drinking water of Greece.     

Fate of disinfection by-products in groundwater during aquifer storage and recovery with reclaimed water

Knowledge on the behaviour of disinfection by-products (DBPs) during aquifer storage and recovery (ASR) is limited even though this can be an important consideration where recovered waters are used for potable purposes. A reclaimed water ASR trial in an anoxic aquifer in South Australia has provided some of the first quantitative information at field-scale on the fate and transport of trihalomethanes (THMs) and haloacetic acids (HAAs). The results revealed that THM half-lives varied from <1 to 65 days, with persistence of chloroform being highest and bromoform lowest. HAA attenuation was rapid (<1 day). Rates of THM attenuation were shown to be highly dependent on the geochemical environment as evidenced by the 2-5 fold reduction in half-lives at the ASR well which became methanogenic during the storage phase of the trial, as compared to an observation well situated 4 m away, which remained nitrate-reducing. These findings agree with previous laboratory-based studies which also show persistence declining with increased bromination of THMs and reducing redox conditions. Modelling suggests that the chlorinated injectant has sufficient residual chlorine and natural organic matter for substantial increases in THMs to occur within the aquifer, however this is masked in some of the field observations due to concurrent attenuation, particularly for the more rapidly attenuated brominated compounds. The model is based on data taken from water distribution systems and may not be representative for ASR since bromide and ammonia concentrations in the injected water and the possible role of organic carbon in the aquifer were not taken into consideration. During the storage phase DBP formation potentials were reduced as a result of the removal of precursor material despite an increase in the THM formation potential per unit weight of total organic carbon. This suggests that water quality improvements with respect to THMs and HAAs can be achieved through ASR in anoxic aquifers.     

Estrogenic activity removal of 17beta-estradiol by ozonation and identification of by-products

This work investigated the degradation of a natural estrogen (17beta-estradiol) and the removal of estrogenic activity by the ozonation process in three different pHs (3, 7 and 11). A recombinant yeast assay (YES assay) was employed to determine estrogenic activity of the ozonized samples and of the by-products formed during the ozonation. Ozonation was very efficient for the removal of 17beta-estradiol in aqueous solutions. High removals (>99%) were achieved with low ozone dosages in the three different pHs. Several by-products were formed during the ozonation of 17beta-estradiol. However, only a few compounds could be identified and confirmed. Different by-products are formed at different pHs, which is probably due to different chemical pathways and different oxidants (O(3) and OH radical). The by-products formed at pH 11 were 10epsilon-17beta-dihydroxy-1, 4-estradieno-3-one (DEO) and 2-hydroxyestradiol, which were not formed in pH 3. Only testosterone could be observed in pH 3, whereas at pH 7 all three by-products were found. At pH 7 and 11 the applied ozone dosages were not enough to remove all the estrogenicity from samples, even though the 17beta-estradiol residual concentration for these two pHs was lower than at pH 3. Higher estrogenicity was detected at pH 11. An explanation to this fact may be that oxidation via OH radical forms more by-products with estrogenic activity. Probably, the formation of 2-hydroxyestradiol at pHs 7 and 11 is contributing to the residual estrogenicity of samples ozonized at these pHs. In this work, complete removal of estrogenic activity was only obtained at pH 3.     

离子色谱在饮用水消毒副产物及高氯酸盐分析中的应用

介绍了离子色谱在饮用水中消毒副产物及高氯酸盐分析中的应用。重点介绍了离子色谱测定饮用水中溴酸盐和高氯酸盐的方法。简单介绍了卤代乙酸和氯酸盐的离子色谱测定法及离子色谱-质谱联用技术在饮用水消毒副产物及高氯酸盐分析中的应用。     

Reducing the formation of disinfection by-products by pre-ozonation.

The objective of this study is to apply the pre-ozonation process to reduce the formation of disinfection by-products (DBPs). The raw water sample, collected from the Te-Chi Reservoir in central Taiwan, has been polluted by fertilizer. Three types of resins were used to isolate the natural organic matter into seven types of organic fractions. The pre-ozonation was used to oxidize each organic fraction to study the reduction of DBPs of each fraction. Experimental results indicated that the pre-ozonation could reduce the concentration of dissolved organic carbon resulting in the reduction of DBP formation. With the pre-ozonation, 9-54% of DOC and more than 40% of DBPs were reduced. With the analysis of UV adsorption and Fourier transform infrared spectrometer (FTIR), the reduction of A254 and unsaturated functional groups such as aromatic ring and C=C bond containing in the water sample is the major reaction mechanism.     

饮用水中典型含氮消毒副产物的生成与控制研究进展

含氮消毒副产物作为一类具有强“三致”作用的高毒性新兴消毒副产物,其生成和控制等相关问题是饮用水处理领域研究的重点和难点。典型的含氮消毒副产物有卤乙腈、亚硝胺、卤代硝基甲烷及卤乙酰胺,在总结这类消毒副产物的生成机制和去除手段的基础上,针对其浓度低、极性强造成富集难、去除率低的瓶颈问题,分别从新材料、新技术研发及工艺优化组合方向提出了消除含氮消毒副产物问题的研究重点,展望了新型纳米功能材料耦合电化学技术处理含氮消毒副产物的发展前景,为解决强“三致”作用的高毒性新兴含氮消毒副产物问题提供参考。