Cadmium biosorption by cells of Spirulina platensis TISTR 8217 immobilized in alginate and silica gel

The biosorption of cadmium by immobilized Spirulina platensis on alginate gel and silica gel was studied. The maximum biosorption capacities for alginate immobilized cells and silica immobilized cells were 70.92 and 36.63 mg Cd/g biomass, respectively. Temperature did not have an influence on metal sorption, whereas an initial pH solution did. Sorption occurred in a wide pH range (pH 3-8). The highest adsorption of alginate immobilized cells was at pH 6, while silica immobilized cell adsorption was not affected at pH between 4 and 7. The immobilized cells were reused in consecutive adsorption-desorption. The results showed that immobilized cells could be repeatedly used in the sorption process up to five times.     

Distributions of zinc, copper, cadmium and lead in a tropical ultisol after long-term disposal of sewage sludge

Heavy metals present in soils constitute serious environmental hazards from the point of view of polluting the soils and adjoining streams and rivers. The distribution of heavy metals in a sandy Ultisol (Arenic Kandiustult) in south eastern Nigeria subjected to 40 years disposal of sewage wastes (sludge and effluents) was studied using two profile pits (S/NSK/1 and S/NSK/2) sited in the sewage disposal area and one profile pit (NS/NSK) sited in the non-sewage disposal area. Soil samples were collected in duplicate from these soil horizons and analyzed for their heavy metal contents. The mean concentrations of Zn, Cu, Cd and Pb in the top- and sub-soil horizons of sewage soil were 79.3, 32, 0.29 and 1.15 mg/kg, respectively. These levels were high enough to constitute health and phytotoxic risks. All the metal levels were much higher in the AB horizon in the sewage than in the non-sewage soil profile, but Pb and Cu contents were also high down to the Bt1 horizon, indicating their apparent relatively high mobility in this soil. There was a significant correlation between organic matter (OM) and Zn (r=0.818**), and between OM and Cd (0.864**) in the sewage soil. The high OM status of the sewage sludge, together with its corresponding low pH, might have favoured metal-OM complexation that could reduce heavy metal mobility and phytotoxicity in this soil.     

Thallium: a review of public health and environmental concerns

Thallium (Tl) is a rare but widely dispersed element. All forms of thallium are soluble enough to be toxic to living organisms. Thallium is more toxic to humans than mercury, cadmium, lead, copper or zinc and has been responsible for many accidental, occupational, deliberate, and therapeutic poisonings since its discovery in 1861. Its chemical behavior resembles the heavy metals (lead, gold and silver) on the one hand and the alkali metals (K, Rb, Cs) on the other. It occurs almost exclusively in natural waters as monovalent thallous cation. The solubility of thallous compounds is relatively high so that monovalent thallium is readily transported through aqueous routes into the environment. Tl can be transferred from soils to crops readily and accrues in food crops. The fascinating chemistry and high toxicity potential make thallium and its compounds of particular scientific interest and environmental concern. Thallium was detected in base-metal mining effluents. The conventional removal of heavy metals from wastewater has little effect on thallium. In this review, various treatment options and removal technologies are enumerated in order to protect the environment from thallium toxicity.     

The effect of operating conditions on the capture of metals with limestone during incineration

The objective of this work was to experimentally study the effect of different operating conditions on sorbent (limestone) to capture metals and the formation of hexavalent chromium during fluidized bed incineration of wastes containing Pb, Cd, Cu, and Cr. The operating parameters evaluated included: 1) addition of organic chloride (PVC); 2) addition of inorganic chloride (NaCl); 3) addition of sulfide (Na₂S); 4) size of sorbent; and, 5) air factor. The experiments were carried out in a pilot scale fluidized bed incinerator with air pollution control devices of two consecutive cyclones and a wet scrubber. Experimental results indicated that limestone could effectively capture most heavy metals Pb, Cr, and Cd in the sand bed. The addition of organic chloride (PVC) and inorganic chloride (NaCl) in feedstock caused different consequences. The former decreased the adsorption efficiency, while the latter increased the adsorption efficiency of limestone in the sand bed. Moreover, the presence of sulfide (Na₂S) was helpful in controlling metals during incineration. Little hexavalent chromium is formed during incineration, but the presence of organic chloride PVC produced more Cr(VI) than inorganic chloride NaCl.     

Adsorption studies on coir pith for heavy metal removal

Biosorption efficiency of coir pith, a waste product from coir industry, was investigated in this study for the removal of metallic pollutants such as Ni, Cu and Zn from aqueous solutions. The disposal of coir pith is a major problem associated with the coir industries, especially working in the small-scale sector. The present study explores the effectiveness of utilization of coir pith, an accumulating waste, as a biosorbent for heavy metal removal. Batch mode studies were done to evaluate the efficiency of removal of metals under varying adsorption conditions of pH, metal concentration and contact time. Characterization studies of the biosorbent and SEM analysis were done. Kinetic modelling studies were tried using Lagergren pseudo-first-order and second-order models. Equilibrium studies were done using well-known Freundlich, Langmuir and D–R isotherm models. It was found that all isotherms are fitting well indicating the efficiency of coir pith as an adsorbent of heavy metals. The applicability of all the three isotherms to the sorption processes shows that both monolayer adsorption and heterogeneous energetic distribution of active sites on the surface of the adsorbent are possible. Due to the abundance and low cost of these materials, adsorption technologies developed can act as good sustainable options for the future in heavy metal removal from industrial effluents.     

Removal of nitrogen oxides with organic amines and metal complexes

Aqueous solutions containing organic amines and metal complexes were applied for the removal of nitrogen oxides. Organic amines were effective for the removal of the mixture composed of nitric oxide and nitrogen dioxide. In particular, methyl and ethyl amines removed these species with 1 : 1 ratio from the mixture at fairly rapid rates. Dinitrogen trioxide (N₂O₃) was suggested to be involved in the course of the removal.Metal complexes removed nitrogen dioxide efficiently. As has been previously reported for a number of inorganic or organic redox systems, it was concluded that the removal of nitrogen dioxide by metal complexes proceeded also by the redox mechanism.Iron (ii) chelate complexes were highly effective for the removal of nitric oxide and this was attributed to a reversible coordination to the complex.     

Heavy metal contamination by Al-fabrication plants in Hong Kong

Leaf samples of six plant species collected from locations near the Al-fabrication plants in Sai Kung, Hong Kong were found to be heavily contaminated by Al, Cd, Pb, Ni, Cu and Zn, as determined by inductively — coupled plasma emission spectrophotometer (ICP). Studies using scanning electron microscope incorporated with X-ray microanalyzer showed that significant amounts of dust, with elevated concentrations of heavy metals, were deposited on the leaf surface. The stomatal pores were partially plugged and the guard cells were distorted. The amount of dust deposition and metal contamination varied significantly among different species. Lantana camara had the highest concentrations of all metals. Washing with deionized water could remove the surficial dust particles and reduce the metal contamination, with a degree of effectiveness depending on plant species and metal species. About 50% of Al and other metals were removed from leaves of L. camara and Fiscus variegata by washing, whereas only 20% removal was recorded in Bauhina variegata, the species had the least dust deposition. The soil samples and Al wastes collected from the same sites also exhibited higher values of total metal concentrations than the control. However, the contents of extractable metals were extremely low and were almost below the limits of detection. Experimental data further suggested that the source of leaf metals was mainly accumulated from metal-enriched aerosols, either from Al-fabrication plants or from automobile exhausts, and contribution from soil was relatively unimportant.     

黄浦江表层沉积物中重金属污染的潜在生态风险评价

采用潜在生态风险指数法对黄浦江表层沉积物中重金属污染的潜在生态风险进行了评价。评价结果表明,黄浦江表层沉积物中重金属的潜在生态风险水平较低,其中杨浦大桥和南市水厂断面达到中等生态风险,其它断面均为轻微生态风险;重金属的潜在生态风险依次为Cd>Hg>Cu>As>Pb>Cr>Zn,除Cd达到中等生态风险外,其余元素均为轻微生态风险。沉积物中重金属的污染水平从上游到下游呈上升趋势,工业排放是水环境中重金属的主要来源,苏州河对黄浦江下游重金属存在一定的输入贡献。相关性分析表明,黄浦江表层沉积物中大多数重金属元素呈现相近的来源特征,有机质是影响沉积物中重金属分布的重要因素。     

Biosorption of uranium by chemically modified Rhodotorula glutinis

The present paper reports the biosorption of uranium onto chemically modified yeast cells, Rhodotorula glutinis, in order to study the role played by various functional groups in the cell wall. Esterification of the carboxyl groups and methylation of the amino groups present in the cells were carried out by methanol and formaldehyde treatment, respectively. The uranium sorption capacity increased 31% for the methanol-treated biomass and 11% for the formaldehyde-treated biomass at an initial uranium concentration of 140 mg/L. The enhancement of uranium sorption capacity was investigated by Fourier transform infrared (FTIR) spectroscopy analysis, with amino and carboxyl groups were determined to be the important functional groups involved in uranium binding. The biosorption isotherms of uranium onto the raw and chemically modified biomass were also investigated with varying uranium concentrations. Langmuir and Freundlich models were well able to explain the sorption equilibrium data with satisfactory correlation coefficients higher than 0.9.     

Evaluation of chemical and ecotoxicological characteristics of biodegradable organic residues for application to agricultural land

The use of organic waste and compost as a source of organic matter and nutrients is a common practice to improve soil physico-chemical properties, meanwhile reducing the need for inorganic fertilisers. Official guidelines to assess sewage sludge and compost quality are mostly based on total metal content of these residues. Measurement of the total concentration of metals may be useful as a general index of contamination, but provides inadequate or little information about their bioavailability, mobility or toxicity when the organic residue is applied to the soil. However, ecotoxicity tests provide an integrated measure of bioavailability and detrimental effects of contaminants in the ecosystem. In the present study, three different types of biodegradable organic residues (BORs) have been considered: sewage sludge from municipal wastewater treatment (SS), compost from the organic fraction of unsorted municipal solid waste (MSWC), and garden waste compost (GWC). The BORs were subjected to chemical characterisation and total metal quantification (Cd, Cr, Cu, Ni, Pb and Zn), in order to verify their suitability for land application. Water leachability was determined through the DIN 38414-S4 method, while the modified BCR sequential extraction procedure was used for metal speciation. Ecotoxicity of the BORs was studied by direct and indirect bioassays. Direct toxicity bioassays were: plant growth tests with cress (Lepidium sativum L.) and barley (Hordeum vulgare L.), and earthworm (Eisenia fetida) mortality. On the other hand, indirect exposure bioassays, with leachate from the residues, took into account: luminescent bacteria (Vibrio fischeri), seed germination (L. sativum and H. vulgare) and Daphnia magna immobilization. As far as total metal concentration is concerned, with particular reference to Zn, SS resulted neither suitable for the use in agriculture nor compatible to be disposed of as an inert material into landfill, according to the Directive 1999/31/EC. Zinc in SS was mainly present in exchangeable form (28.5%), appearing as highly bioavailable. As a consequence, SS exhibited either high ecotoxicity effects with the indirect exposure bioassays or significant mortality with the earthworm bioassay. Total content of metals in MSWC allowed its classification as "stabilised biowaste", according to 2nd draft [DG Env.A.2. Working document of Biological treatment of biowaste - 2nd draft. Directorate-General Environment, Brussels, 12th February; 2001. accessed in:http://europa.eu.int/comm/environment/waste/facts_en.htm, at 10/09/2002] while leachate, on the basis of the concentration of these contaminants, could be classified as "inert waste". This residue showed significant ecotoxicity effects with direct exposure bioassays as well as with the luminescent bacteria bioassay. However, it resulted less toxic than SS. Finally, GWC could be classified as a Class 2 compost, with no detectable toxic effects on the organisms used in the bioassays, except for the luminescent bacteria. In this case, an EC(50) of 73.0% was observed. Considering the results, the use of a battery of toxicity test in conjunction with chemical analysis should be suggested, in order to correctly assess possible environmental risks deriving from disposal or land application of biodegradable organic residues.     

The determination of trace metal pollutants in environmental matrices using ion chromatography

A review is presented detailing the development of ion chromatography (IC) as a selective analytical tool for the determination of toxic metals and their organic species in many environmental sample matrices. A brief outline of ion chromatographic principles, together with an overview of the stationary phases used to separate metals, namely ion exchangers, modified ion pair sorbents and chelating ion exchangers, and the methods for detecting metal ions including hyphenation with spectroscopy and sample preparation schemes are also given, prior to a critical examination of developed methods for various metals including arsenic, chromium, cadmium, lead, mercury, beryllium, aluminium and uranium since 1990.     

Comparison of differences between copper bioaccumulation and biosorption

Biological methods for wastewater treatment are becoming more accepted all over the world. The method, which makes use of accumulating abilities of living cells, is called bioaccumulation. In contrast with it, biosorption takes advantage of sequestering capabilities of dry or dead cells, which is technologically advantageous. The differences between bioaccumulation and biosorption of copper from model solutions were studied in this work. Application of living algal cells has some disadvantages. Copper significantly damages the surface of living cells, which results in partial loss of cell-binding abilities and release of accumulated copper back into solution. The binding capacity of living cells is significantly lower than that of dead cells. There is also a possibility of desorption and reuse of biomass in case of biosorption.     

The effects of FeCl3 on the distribution of the heavy metals Cd, Cu, Cr, and Zn in a simulated multimetal incineration system

Recognizing that waste-derived chlorine can enhance heavy metal emissions by forming volatile metallic chlorides during municipal solid waste (MSW) combustion, and that in Taiwan, FeCl3-containing sewage sludge may either be landfilled or coincinerated with other MSW, this study thus investigated the effects of FeCl3 on the speciation and partitioning of heavy metals in a multimetal incineration system by using a tubular furnace and FeCl3-spiked simulated wastes. The molar ratio of chlorine content to heavy metal content (referred to as the Cl/ M ratio), ranging from 3 to 200, was used as a parameter to evaluate the effects of chlorine on the movement of heavy metals between the incinerator discharges. Results indicate that speciation and partitioning were related to the affinity between the chlorine and the heavy metals and between chlorine and hydrogen in the combustion system. The effectiveness of increasing the Cl/M ratio to the formation potential of metallic chlorides and on the shift of heavy metals from the bottom ash to the fly ash and/or the flue gases was found to have in increasing order as follows: Zn>Cu>Cr, a phenomenon basically reflecting the volatility of the heavy metals and their chlorides formed during combustion.     

Correlation of field-measured toxicity with chemical concentration and pollutant availability.

Direct field toxicity tests were performed in two Louisiana waterways, Bayous Trepagnier and St. John, on sediments containing organic/heavy metal mixtures. Our approach involved bioluminescent bacterial toxicity assays (using DeltaTox, which qualitatively identifies polluted areas, and Microtox, which quantifies toxicity). Samples were more completely analyzed in our laboratory using inductively coupled plasma atomic emission spectroscopy (ICP-AES) and gas chromatography/mass spectrometry (GC/MS). Results indicate that lead is the primary toxic metal at the sites examined, though concentrations of metals fluctuate due to spatial variation and the dynamic nature of the waterways. Polycyclic aromatic hydrocarbons (PAHs) are the most abundant group of organics measured and appear to contribute to the overall toxic response. DeltaTox located toxic hotspots where there was an average light loss of 53-100%. Toxicity results from both assays agree but are well correlated with concentration measurements only for certain sediment fractions. Overall, the DeltaTox/Microtox approach appears to be rapid and cost effective for on-site hotspot identification, and may increase understanding of hazards associated with heavy metal and organic contaminants in these waterways.     

Remobilisation of 109Cd, 65Zn and 54Mn from freshwater-labelled river sediments when mixed with seawater

A major fraction of trace metals transported by rivers is associated with sediments, especially during flooding, when erosion and resuspension increase sediment loads. Upon contact with seawater in estuaries, changes in ionic strength and pH may remobilise trace metals from sediment surfaces into more bioavailable forms. The objective of the present work was to investigate time-dependent interactions between trace metals and freshwater sediments and their potential remobilisation upon contact with seawater. Two river sediments (one organic and one inorganic) were labelled with 109Cd2+, 65Zn2+ and 54Mn2+ radioactive tracers for periods up to 6 months. Sorption of tracers occurred rapidly (> or = 80% sorption, < 1 h), followed by a slower approach to pseudoequilibrium. Kd(6 months) were estimated as 460, 480 and 2200 ml/g (inorganic sediment) compared to 5300, 4000 and 1200 ml/g (organic sediment) for 109Cd, 65Zn and 54Mn, respectively. Remobilisation of tracers from labelled sediments was studied using sequential extractions. Artificial seawater extracts simulated an estuarine environment. Subsequent extractions provided information about more strongly sorbed tracer fractions within sediments. Remobilisation of 109Cd by seawater was significant (> 65%) and least affected by sediment type or freshwater labelling time. Redistribution of Cd to strongly bound phases was minimal (4% and 1% of 109Cd in strongly oxidisable fractions). Seawater remobilisation of 65Zn was significantly greater from the organic sediment (54%) compared to the inorganic sediment (8%), where a large fraction of 65Zn (14%) became irreversibly bound. Similarly, more 54Mn was remobilised by seawater from the organic sediment than the inorganic sediment (66% and 3% remobilised, respectively), i.e., 54Mn became more strongly bound in the inorganic sediment. A simple three-box model, based on first-order differential equations, was used to describe the interaction between tracers in spiked freshwater and two operationally defined sediment fractions ("seawater exchangeable" and "seawater unexchangeable") up to 6 months of freshwater labelling. Model simulations were fitted to experiment data and apparent rate constants were calculated using numerical optimisation methods. Sorption ratios from modelling data (i.e., k1/k2) were greater for organic compared to inorganic sediments, while fixation ratios were higher in inorganic sediments. In conclusion, trace metals can be remobilised from sediments on contact with seawater in estuaries. High organic content in sediments increased initial sorption of tracers but inhibited redistribution to more strongly bound fractions over time, resulting in greater remobilisation of tracers when in contact with seawater.     

Nonylphenol in the environment: a critical review on occurrence, fate, toxicity and treatment in wastewaters

Nonylphenol is a toxic xenobiotic compound classified as an endocrine disrupter capable of interfering with the hormonal system of numerous organisms. It originates principally from the degradation of nonylphenol ethoxylates which are widely used as industrial surfactants. Nonylphenol ethoxylates reach sewage treatment works in substantial quantities where they biodegrade into several by-products including nonylphenol. Due to its physical-chemical characteristics, such as low solubility and high hydrophobicity, nonylphenol accumulates in environmental compartments that are characterised by high organic content, typically sewage sludge and river sediments, where it persists. The occurrence of nonylphenol in the environment is clearly correlated with anthropogenic activities such as wastewater treatment, landfilling and sewage sludge recycling. Nonylphenol is found often in matrices such as sewage sludge, effluents from sewage treatment works, river water and sediments, soil and groundwater. The impacts of nonylphenol in the environment include feminization of aquatic organisms, decrease in male fertility and the survival of juveniles at concentrations as low as 8.2 mug/l. Due to the harmful effects of the degradation products of nonylphenol ethoxylates in the environment, the use and production of such compounds have been banned in EU countries and strictly monitored in many other countries such as Canada and Japan. Although it has been shown that the concentration of nonylphenol in the environment is decreasing, it is still found at concentrations of 4.1 mug/l in river waters and 1 mg/kg in sediments. Nonylphenol has been referred to in the list of priority substances in the Water Frame Directive and in the 3rd draft Working Document on Sludge of the EU. Consequently there is currently a concern within some industries about the possibility of future regulations that may impose the removal of trace contaminants from contaminated effluents. The significance of upgrading sewage treatment works with advanced treatment technologies for removal of trace contaminants is discussed.     

Leaf litter breakdown in streams receiving treated and untreated metal mine drainage

Rates of alder leaf decomposition were used as an ecosystem-level measure of effects of untreated and treated acid mine drainage on two Colorado mountain streams. Untreated mine effluents had low pH and high concentrations of metals, particularly iron. Deposition of ferric hydroxide on leaf surfaces inhibited colonization by decomposers, such as fungi and aquatic insects, and thus little leaf breakdown occurred. Treated effluents had improved water quality (basic pH, low metal concentrations), but suspended flocs released by the treatment process buried leaves and reduced consumer activity. The rate of leaf breakdown was not significantly different from the rate with untreated effluents; thus improvement in water quality alone was insufficient to restore this important pathway of energy flow in headwater streams.     

A critical review of the bioavailability and impacts of heavy metals in municipal solid waste composts compared to sewage sludge

The content, behaviour and significance of heavy metals in composted waste materials is important from two potentially conflicting aspects of environmental legislation in terms of: (a) defining end-of-waste criteria and increasing recycling of composted residuals on land and (b) protecting soil quality by preventing contamination. This review examines the effects of heavy metals in compost and amended soil as a basis for achieving a practical and sustainable balance between these different policy objectives, with particular emphasis on agricultural application. All types of municipal solid waste (MSW) compost contain more heavy metals than the background concentrations present in soil and will increase their contents in amended soil. Total concentrations of heavy metals in source-segregated and greenwaste compost are typically below UK PAS100 limits and mechanical segregated material can also comply with the metal limits in UK PAS100, although this is likely to be more challenging. Zinc and Pb are numerically the elements present in the largest amounts in MSW-compost. Lead is the most limiting element to use of mechanically-segregated compost in domestic gardens, but concentrations are typically below risk-based thresholds that protect human health. Composted residuals derived from MSW and greenwaste have a high affinity for binding heavy metals. There is general consensus in the scientific literature that aerobic composting processes increase the complexation of heavy metals in organic waste residuals, and that metals are strongly bound to the compost matrix and organic matter, limiting their solubility and potential bioavailability in soil. Lead is the most strongly bound element and Ni the weakest, with Zn, Cu and Cd showing intermediate sorption characteristics. The strong metal sorption properties of compost produced from MSW or sewage sludge have important benefits for the remediation of metal contaminated industrial and urban soils. Compost and sewage sludge additions to agricultural and other soils, with background concentrations of heavy metals, raise the soil content and the availability of heavy metals for transfer into crop plants. The availability in soil depends on the nature of the chemical association between a metal with the organic residual and soil matrix, the pH value of the soil, the concentration of the element in the compost and the soil, and the ability of the plant to regulate the uptake of a particular element. There is no evidence of increased metal release into available forms as organic matter degrades in soil once compost applications have ceased. However, there is good experimental evidence demonstrating the reduced bioavailability and crop uptake of metals from composted biosolids compared to other types of sewage sludge. It may therefore be inferred that composting processes overall are likely to contribute to lowering the availability of metals in amended soil compared to other waste biostabilisation techniques. The total metal concentration in compost is important in controlling crop uptake of labile elements, like Zn and Cu, which increases with increasing total content of these elements in compost. Therefore, low metal materials, which include source-segregated and greenwaste composts, are likely to have inherently lower metal availabilities overall, at equivalent metal loading rates to soil, compared to composted residuals with larger metal contents. This is explained because the compost matrix modulates metal availability and materials low in metals have stronger sorption capacity compared to high metal composts. Zinc is the element in sewage sludge-treated agricultural soil identified as the main concern in relation to potential impacts on soil microbial activity and is also the most significant metal in compost with regard to soil fertility and microbial processes. However, with the exception of one study, there is no other tangible evidence demonstrating negative impacts of heavy metals applied to soil in compost on soil microbial processes and only positive effects of compost application on the microbial status and fertility of soil are reported. The negative impacts on soil microorganisms apparent in one long-term field experiment could be explained by the exceptionally high concentrations of Cd and other elements in the applied compost, and of Cd in the compost-amended soil, which are unrepresentative of current practice and compost quality. The metal contents of source-segregated MSW or greenwaste compost are smaller compared to mechanically-sorted MSW-compost and sewage sludge, and low metal materials also have the smallest potential metal availabilities. Composting processes also inherently reduce metal availability compared to other organic waste stabilisation methods. Therefore, risks to the environment, human health, crop quality and yield, and soil fertility, from heavy metals in source-segregated MSW or greenwaste-compost are minimal. Furthermore, composts produced from mechanically-segregated MSW generally contain fewer metals than sewage sludge used as an agricultural soil improver under controlled conditions. Consequently, the metal content of mechanically-segregated MSW-compost does not represent a barrier to end-use of the product. The application of appropriate preprocessing and refinement technologies is recommended to minimise the contamination of mechanically-segregated MSW-compost as far as practicable. In conclusion, the scientific evidence indicates that conservative, but pragmatic limits on heavy metals in compost may be set to encourage recycling of composted residuals and contaminant reduction measures, which at the same time, also protect the soil and environment from potentially negative impacts caused by long-term accumulation of heavy metals in soil.     

Are sunscreens a new environmental risk associated with coastal tourism?

The world coastal-zone population and coastal tourism are expected to grow during this century. Associated with that, there will be an increase in the use of sunscreens and cosmetics with UV-filters in their formulation, which will make coastal regions worldwide susceptible to the impact of these cosmetics. Recent investigations indicate that organic and inorganic UV-filters, as well as many other components that are constituents of the sunscreens, reach the marine environment - directly as a consequence of water recreational activities and/or indirectly from wastewater treatment plants (WWTP) effluents. Toxicity of organic and inorganic UV filters has been demonstrated in aquatic organism. UV-filters inhibit growth in marine phytoplankton and tend to bioaccumulate in the food webs. These findings together with coastal tourism data records highlight the potential risk that the increasing use of these cosmetics would have in coastal marine areas. Nevertheless, future investigations into distribution, residence time, aging, partitioning and speciation of their main components and by-products in the water column, persistence, accumulation and toxicity in the trophic chain, are needed to understand the magnitude and real impact of these emerging pollutants in the marine system.     

Revegetating fly ash landfills with Prosopis juliflora L.: impact of different amendments and Rhizobium inoculation

A revegetation trial was conducted to evaluate the feasibility of growing a legume species, Prosopis juliflora L., on fly ash ameliorated with combination of various organic amendments, blue-green algal biofertilizer and Rhizobium inoculation. Significant enhancements in plant biomass, photosynthetic pigments, protein content and in vivo nitrate reductase activity were found in the plants grown on ameliorated fly ash in comparison to the plants growing in unamended fly ash or garden soil. Higher growth was obtained in fly ash amended with blue-green algae (BGA) than farmyard manure or press mud (PM), a waste from sugar-processing industry, due to the greater contribution of plant nutrients, supply of fixed nitrogen and increased availability of phosphorus. Nodulation was suppressed in different amendments of fly ash with soil in a concentration-duration-dependent manner, but not with other amendments. Plants accumulated higher amounts of Fe, Mn, Cu, Zn and Cr in various fly ash amendments than in garden soil. Further, inoculation of the plant with a fly ash tolerant Rhizobium strain conferred tolerance for the plant to grow under fly ash stress conditions with more translocation of metals to the above ground parts. The results showed the potential of P. juliflora to grow in plantations on fly ash landfills and to reduce the metal contents of fly ash by bioaccumulation in its tissues.