纳米复合ZnO-TiO2晶体的制备及其光电催化性能研究

采用溶胶-凝胶法制备了纳米复合半导体ZnO-TiO2薄膜,并进行了结构和光电催化性能的测试.TiO2薄膜对五氯酚溶液的光电催化降解结果表明当输入正向偏压后,其光催化性能有较大提高.由于ZnO的掺入,半导体薄膜电极的光吸收能力增强;同时,Zn2+可能作为光生载流子的浅俘获中心,导致表面界面电荷转移加速,从而延长光生电子/空穴对的寿命并抑制其复合,有效地提高了TiO2薄膜光电催化活性.     

Mo-N-TiO_2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显＂红移＂,且钼酸铵添加量（相对TiO2）为0.5%的样品＂红移＂程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4＋,以Mo6＋形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

纳米TiO2薄膜在不同陶瓷表面的负载及其光催化性能研究

利用2种不同表面处理的陶瓷作为载体,用溶胶凝胶法在其表面进行了纳米TiO2光催化薄膜的负载.采用X射线衍射法(XRD)、X射线光电子能谱仪(XPS)和扫描电镜(SEM)对薄膜的粒径、横断面及表面组成进行了表征和分析,结果表明,TiO2的平均粒径约为15 nm,釉面陶瓷TiO2薄膜分布均匀,膜厚约为300 nm;无釉陶瓷TiO2薄膜分布不均,膜层不明显;2种载体中的一些基质离子在TiO2薄膜有渗透.苯酚的降解实验表明,以2种不同表面处理的陶瓷为载体的TiO2薄膜对苯酚的降解均符合一级反应动力学,就催化活性而言,TiO2/釉面陶瓷＞TiO2/无釉陶瓷,分析认为基质渗透的Ca2 有降低TiO2光催化活性的作用;该薄膜对实际生产多菌灵废水具有催化降解作用.重复降解实验20次,TiO2/釉面陶瓷和TiO2/无釉陶瓷对苯酚的去除率仅分别降低9%和6%.     

Effect of ZnFe2O4 doping on the photocatalytic activity of TiO2

The photocatalytic oxidation of the organic pollutants with the TiO2 as photocatalyst has been widely studied in the world, and many achievements have been got. The degradation of pollutants is highly related with the photocatalytic activity of TiO2. It is demonstrated that doping ions or oxides to TiO2 is one way to enhance the photocatalytic activity of TiO2. In this paper, the ZnFe2O4-doped TiO2 nanoparticles were prepared from butyl titanate by a sol-gel method and characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results showed that when TiO2 was doped with ZnFe2O4, its particle size will decrease and its crystal structure will partly transform from anatase to rutile. The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that doping ZnFe2O4 to TiO2 will enhance the photocatalytic activity of TiO2 and that ZnFe2O4-doped TiO2 in the coexistence of anatase and rutile has higher efficiency for the degradation of Rhodamine B than that in the anatase phase alone. Also the different role of O2 in the direct photolysis and photocatalysis of Rhodamine B was discussed.     

Photocatalytic degradation of p-nitrophenol on nanometer size titanium dioxide surface modified with 5-sulfosalicylic acid

The surface of nanometer size TiO(2) was simply and fast modified by chemical adsorption in saturated solution of 5-sulfosalicylic acid. After surface modification, a stable, yellow surface complex was formed quickly, the wavelength response range of TiO(2) was expanded, it has obvious absorption in the region from 320 to 450 nm; the adsorption efficiency of p-nitrophenol (PNP) by TiO(2) was enhanced from 42% to 84%. The photocatalytic activity was tested on the degradation of PNP. The influences of catalyst and its dosage, pH value, and PNP concentration on the degradation were investigated. On optimal photodegradation conditions, including initial pH 4.0, PNP 5 mg l(-1), catalyst 100 mg, irradiation time 120 min with 160 W high-pressure mercury lamp, the degradation efficiency of PNP was increased from 40% to 88% after surface modification. Surface modification led not only to an increase in the light utilization, but also improved the surface coverage of PNP in comparison with the pure TiO(2). Both of these factors are crucial for the photocatalytic activity of heterogeneous photocatalysis, especially for photodegradation of benzenoid pollutants.     

Mo-N-TiO2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显"红移",且钼酸铵添加量(相对TiO2)为0.5%的样品"红移"程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4+,以Mo6+形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

The direct photolysis and photocatalytic degradation of alachlor at different TiO2 and UV sources

Direct photolysis and photocatalytic degradations of alachlor, a widely used herbicide, were studied using three different monochromatic UV lamps (254, 300 and 350 nm) and two TiO(2) sources. Both the direct photolysis and photocatalytic degradations of alachlor follow pseudo-first-order decay kinetics. TiO(2)-P25 was found to be an effective photocatalyst compared to TiO(2)-BDH. The direct photolysis of alachlor was dominant at 254 nm even if TiO(2) was present in the solution. Among the three UV wavelengths used, the highest photocatalysis quantum yield was obtained at 300 nm. The photocatalytic degradation rate of alachlor increased with the dosages of TiO(2), but an overdose of TiO(2) would retard the reaction due to light attenuation. Photocatalytic reactions were slightly enhanced in an alkaline medium, and the different proton sources causing various degrees of rate retardation were due to the presence of the corresponding counter anions. This effect was diminished at a later stage after the reaction intermediates were formed.     

CdS-TiO2/MWCNTs结构表征及其光催化性能

采用溶胶-凝胶法,制备了多壁碳纳米管（MWCNTs）负载的双组分复合半导体光催化剂CdS-TiO2/MWCNTs。通过透射电镜（TEM）、比表面分析（BET）、X射线衍射（XRD）和紫外-可见吸收光谱（UV-vis）等分析方法对光催化剂进行了结构表征,并考察了CdS-TiO2/MWCNTs对甲苯降解的光催化性能。结果表明：纳米活性粒子CdS-TiO2均匀负载于MWCNTs上,比表面积、光吸收阈值和强度增大,活性粒子间以及活性粒子与载体之间具有协同作用,有利于光催化性能的提高,CdS-TiO2/MWCNTs在主波长为254 nm紫外光照射下对甲苯的降解效果较好,去除率可达55.3%。     

Photocatalytic elimination of indoor air biological and chemical pollution in realistic conditions

The photocatalytic elimination of microorganisms from indoor air in realistic conditions and the feasibility of simultaneous elimination of chemical contaminants have been studied at laboratory scale. Transparent polymeric monoliths have been coated with sol-gel TiO(2) films and used as photocatalyst to treat real indoor air in a laboratory-scale single-step annular photocatalytic reactor. The analytical techniques used to characterize the air quality and analyze the results of the photocatalytic tests were: colony counting, microscopy and PCR with subsequent sequencing for microbial quantification and identification; automated thermal desorption coupled to gas chromatography with mass spectrometry detection for chemical analysis. The first experiments performed proved that photocatalysis based on UVA-irradiated TiO(2) for the reduction of the concentration of bacteria in the air could compete with the conventional photolytic treatment with UVC radiation, more expensive and hazardous. Simultaneously to the disinfection, the concentration of volatile organic compounds was greatly reduced, which adds value to this technology for real applications. The fungal colony number was not apparently modified.     

Enhanced photocatalysis of pentachlorophenol by metal-modified titanium (IV) oxide

The effects of four metals (Ag, Au, Pt, and Cu) doped on TiO2 on the photocatalysis of pentachlorophenol (PCP) were investigated. The results of this study indicated that all four metals-doped TiO2 catalysts were able to enhance the efficiency of PCP photocatalysis with an optimum metallic content of 0.1 wt%. For the metal-doped TiO2 samples (Au, Pt, and Cu), the patterns of light absorption were significantly extended toward visible light spectra in the wavelengths between 400 and 800 nm. The photocatalysis of PCP was pH dependent with the maximum degradation rate achieved in the solution at pH 3. The formation of chloride ion corresponded with the concentration of PCP degraded which confirmed that dechlorination was the major pathway of PCP photocatalysis. The overall toxicities of PCP samples were reduced with the extension of light exposure using the microtox test. The results of PCP photocatalysis are also discussed based on the characteristics of metal/TiO2 including X-ray differential (XRD) patterns, Brunquer Emmett Teller (BET) specific area analysis, and Ultra Violet (UV)-Vis absorption spectra.     

Sonophotocatalytic degradation of alazine and gesaprim commercial herbicides in TiO2 slurry

The photocatalytic degradation of alazine and gesaprim commercial herbicides was carried out in aqueous TiO(2) suspensions under UV light (15W, 352 nm). Degradation of these herbicides was also observed by the combined effects of photocatalysis with sonolysis (sonophotocatalysis) using an ultrasound source of 20kHz. Degradation profiles were recorded by measuring the concentration of the active compounds present in the alazine (alachlor and atrazine) and gesaprim (atrazine) by HPLC as a function of irradiation time (sound and/or light). Over 90% of the active component in the gesaprim was abated and those in alazine were completely degraded. The content of total organic carbon and chemical oxygen demand was also monitored. Mineralization of the commercial herbicides was achieved. Over 80% of chemical oxygen demand abatement was attained for both herbicides with sonophotocatalysis at 150 min of irradiation time. The photocatalytic degradation of the herbicides followed a pseudo-first order kinetics and their rate constant was increased by the combined effects of sonolysis.     

Enhanced Photocatalysis of Pentachlorophenol by Metal-Modified Titanium (IV) Oxide

The effects of four metals (Ag, Au, Pt, and Cu) doped on TiO₂ on the photocatalysis of pentachlorophenol (PCP) were investigated. The results of this study indicated that all four metals-doped TiO₂ catalysts were able to enhance the efficiency of PCP photocatalysis with an optimum metallic content of 0.1 wt%. For the metal-doped TiO₂ samples (Au, Pt, and Cu), the patterns of light absorption were significantly extended toward visible light spectra in the wavelengths between 400 and 800 nm. The photocatalysis of PCP was pH dependent with the maximum degradation rate achieved in the solution at pH 3. The formation of chloride ion corresponded with the concentration of PCP degraded which confirmed that dechlorination was the major pathway of PCP photocatalysis. The overall toxicities of PCP samples were reduced with the extension of light exposure using the microtox test. The results of PCP photocatalysis are also discussed based on the characteristics of metal/TiO₂ including X-ray differential (XRD) patterns, Brunquer Emmett Teller (BET) specific area analysis, and Ultra Violet (UV)-Vis absorption spectra.     

Photocatalytic degradation of dyes on a magnetically separated photocatalyst under visible and UV irradiation

A novel kind of magnetically separable photocatalyst of TiO2/SiO2/gamma-Fe2O3 (TSF) is prepared. Scanning tunnel microscope (STM) and X-ray diffractometer (XRD) were used to characterize the structure of the photocatalyst. In the TSF photocatalyst, a TiO2 shell is for photocatalysis, a gamma-Fe2O3 core as a carrier is for separation by the magnetic field and a SiO2 membrane between the TiO2 shell and the gamma-Fe2O3 core is used to weaken the adverse influence of gamma-Fe2O3 on the photocatalysis of TiO2. Three kinds of dyes, Fluoresein, Orange II and Red acid G, were used to examine the photocatalytic activity of TSF. Due to strong UV adsorption of the gamma-Fe2O3, the photocatalytic activity of TSF was lower than that of the pure TiO2. Deducting the light absorption of the gamma-Fe2O3 particles, the photocatalytic activity of TSF was found to be higher than that of the P25 under UV irradiation. On the other hand, the photocatalytic activity of TSF under visible irradiation was much lower than that of the P25 TiO2 even deducting the visible light absorption of the gamma-Fe2O3 particles. Differences in the photocatalytic mechanisms under UV and visible irradiation lead to the differences in the photodegradation characteristics of dyes on TSF. The recycled TSF exhibited a good repeatability of photocatalytic activity.     

模拟室内环境下掺杂TiO_2纳米晶体的光催化性能

采用环境测试舱模拟可见光下的室内环境,以甲醛气体的光催化降解为探针反应,评价了通过溶胶-凝胶法分别制备的8种（银Ag、铜Cu、铁Fe、钨W、铈Ce、镧La、硫S和氯C l）掺杂TiO2纳米晶体的光催化活性及对甲醛气体的去除效果。用X射线衍射、激光粒度分析和紫外-可见分光光谱表征了掺杂钠米TiO2的微晶尺寸、晶体结构与光学性能。结果表明,Cu掺杂可以提高TiO2对氧的吸附能力,减少纳米粒子表面光生电子与光生空穴的复合,使TiO2的光吸收带边发生红移且有利于对可见光的吸收,从而使Cu掺杂TiO2在模拟室内环境下光催化甲醛气体的能力得到明显提高。     

CdS-TiO_2/MWCNTs结构表征及其光催化性能

采用溶胶-凝胶法,制备了多壁碳纳米管(MWCNTs)负载的双组分复合半导体光催化剂CdS-TiO2/MWCNTs。通过透射电镜(TEM)、比表面分析(BET)、X射线衍射(XRD)和紫外-可见吸收光谱(UV-vis)等分析方法对光催化剂进行了结构表征,并考察了CdS-TiO2/MWCNTs对甲苯降解的光催化性能。结果表明:纳米活性粒子CdS-TiO2均匀负载于MWCNTs上,比表面积、光吸收阈值和强度增大,活性粒子间以及活性粒子与载体之间具有协同作用,有利于光催化性能的提高,CdS-TiO2/MWCNTs在主波长为254 nm紫外光照射下对甲苯的降解效果较好,去除率可达55.3%。     

The photocatalytic degradation of methylene blue by green semiconductor films that is induced by irradiation by a light-emitting diode and visible light

This study develops a low-energy rotating photocatalytic contactor (LE-RPC) that has Cu-doped TiO₂ films coated on stainless-steel rotating disks, to experimentally evaluate the efficiency of the degradation and decolorization of methylene blue (MB) under irradiation from different light sources (visible 430 nm, light-emitting diode [LED] 460 nm, and LED 525 nm). The production of hydroxyl radicals is also examined. The experimental results show that the photocatalytic activity of TiO₂ that is doped with Cu²⁺ is induced by illumination with visible light and an LED. More than 90% of methylene blue at a 10 mg/L concentration is degraded after illumination by visible light (430 nm) for 4 hr at 20 rpm. This study also demonstrates that the quantity of hydroxyl radicals produced is directly proportional to the light energy intensity. The greater the light energy intensity, the greater is the number of hydroxyl radicals produced.

Implications: The CuO-doped anatase TiO₂ powder was successfully synthesized in this study by a sol–gel method. The catalytic abilities of the stainless-steel film were enhanced in the visible light regions. This study has successfully modified the nano-photocatalytic materials to drop band gap and has also successfully fixed the nano-photocatalytic materials on a substratum to effectively treat dye wastewater in the range of visible light. The results can be useful to the development of a low-energy rotating photocatalytic contactor for decontamination purposes.     

Removal and Destruction of Organic Contaminants in Water Using Adsorption,Steam Regeneration,and Photocatalytic Oxidation: A Pilot-Scale Study

ABSTRACT

The overall objective of this pilot-scale study is to investigate the technical feasibility of the removal and destruction of organic contaminants in water using adsorption and photocatalytic oxidation. The process consists of two consecutive operational steps: (1) removal of organic contaminants using fixed-bed adsorption; and (2) regeneration of spent adsorbent using photocatalysis or steam, followed by decontamination of steam condensate using photocatalysis. The pilot-scale study was conducted to evaluate these options at a water treatment plant in Wausau (Wisconsin) for treatment of groundwater contaminated with tetrachloroethene (PCE), trichloroethene (TCE), cis-dichloroethene (cis-DCE), toluene, ethylbenzene (EB), and xylenes. The adsorbents used were F-400 GAC and Ambersorb 563.

In the first treatment strategy, the adsorbents were impregnated with photocatalyst and used for the removal of aqueous organics. The spent adsorbents were then exposed to ultraviolet light to achieve photocatalytic regeneration. Regeneration of adsorbents using photocatalysis was observed to be not effective, probably because the impregnated photocatalyst was fouled by background organic matter present in the groundwater matrix.

In the second treatment strategy, the spent adsorbents were regenerated using steam, followed by cleanup of steam condensate using photocatalysis. Four cycles of adsorption and three cycles of steam regeneration were performed. Ambersorb 563 adsorbent was successfully regenerated using saturated steam at 160 °C within 20 hours. The steam condensate was treated using fixed-bed photo-catalysis using 1% Pt-TiO₂ photocatalyst supported on silica gel. After 35 minutes of empty bed contact time, more than 95% removal of TCE, cis-DCE, toluene, EB, and xylenes was achieved, and more than 75% removal of PCE was observed.

In the case of activated carbon adsorbent, steam regeneration was not effective, and a significant loss in adsorbent capacity was observed.     

模拟可见光下掺杂TiO_2对甲醛溶液光催化降解

模拟自然条件下的可见光,以甲醛的光催化降解为探针反应,评价了通过溶胶-凝胶法分别制备的8种（银Ag、铜Cu、铁Fe、钨W、铈Ce、镧La、硫S、氯Cl）掺杂TiO2纳米晶体的光催化活性及对甲醛水溶液的去除效果。用X射线衍射、激光粒度分析和紫外-可见分光光谱表征了掺杂纳米TiO2的微晶尺寸、晶体结构与光学性能。结果表明：Ce离子尽管有较大的半径但是主要还是掺杂到晶格中,Ce掺杂可以促进TiO2由非正分锐钛矿相向锐钛矿相和金红石相的转变,抑制载流子复合,使TiO2的光吸收带边发生红移且有利于对可见光的吸收,从而使Ce掺杂TiO2在模拟可见光下光催化甲醛水溶液的能力得到明显提高。     

Preparation of a titanium dioxide photocatalyst codoped with cerium and iodine and its performance in the degradation of oxalic acid

A novel class of visible light-activated photocatalysts was prepared by codoping TiO(2) with cerium and iodine (Ce-I-TiO(2)). The particles were characterized using the Brunauer-Emmett-Teller method, X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV-Visible light absorption. Particles of Ce-I-TiO(2) had greater photoabsorption in the 400-800 nm wavelength range than iodine-doped TiO(2) (I-TiO(2)). The effects on the photocatalytic degradation of oxalic acid under visible light or UV-Visible light irradiation were investigated. The photocatalytic activity of Ce-I-TiO(2) calcined at 673 K was significantly higher than that of Ce-I-TiO(2) calcined at 773 K and I-TiO(2) calcined at 673 K in aqueous oxalic acid solution under visible light or UV-Visible light irradiation. Under visible light irradiation, oxalic acid was first adsorbed on the surface of the catalysts rather than reacted with free radicals in the bulk solution, and then oxidized by (·)OH(ads) to CO(2), which was verified by studying the effects of nitrogen purging and scavengers, as well as by gas chromatography/mass spectrometry.