主动采样法采集博物馆空气中微量污染气体

根据博物馆污染气体的种类,对气体主动采样法进行了采样器种类、吸收液种类和浓度、吸收液体积的选择。验证了气体采样流量、采样时间与气体采样浓度的线性关系,确定了酸性和碱性污染气体的主动采样方法,为监测文物保存环境污染气体提供了可行方法。     

浅析被动采样器监测环境空气质量数据的可比性

对被动采样器与空气自动站监测环境空气质量进行了全年的对比实验,并对大量的监测数据进行了规范的处理分析。结果表明,被动采样器在环境条件持续稳定满足采样条件时,被动采样器与自动站监测结果无显著性差异;在环境条件不能持续稳定满足采样条件时,二者监测结果有显著性差异,但仍有较大的相关性。     

几种常见被动采样技术在水环境中研究进展

总结了半透膜被动采样器(SPMDs)、极性有机化合物整合采样器(POCIS)、化学捕收器(Chemcatcher)和硅橡胶被动采样器(Silicon rubber)几种常用被动采样器的结构组成、应用模型、原理、样品的前处理、影响因素及应用范围,指出几种被动采样技术应用上存在的问题,并对其应用前景进行总结和展望。     

被动采样在水体中有机污染监测的应用:以PAHs为例

半透膜采样技术是一种可原位、连续、动态监测水环境中非极性、弱极性有机污染物的被动采样技术,已在国内外发展20余年,但在环境监测中使用很少。从半透膜被动采样特点、采样器构造入手,着重对应用该技术的环节进行剖析,同时涉及被动采样结果及其评价方法。最后以多环芳烃（PAHs）为例,综述了近年来SPMD技术监控水体中非极性、弱极性有机污染物的常用分析技术及其发展。     

污水自动采样器代替人工采样的可行性分析

选择某炼油厂污水总排口水跃区断面 ,安装采样器探头 ,进行采样器与人工同步采样 ,实验室分析得 2 3组监测数据。 1误差分析 :设人工采样为真值 ,采样器采样视为测定值 ,则 :相对误差 =测定值 -真值真值 × 1 0 0 %　　结果表明 ,石油含量在 1 0 mg/L以下的 1 2组数据误差范围在 - 5.3%～ 2 3.9% ,采样器采样低1 5.4 % ;含油量比较高的 1 1组数据误差范围在 0～ 2 5.0 % ,采样器采样低 1 3.5%。经相关分析和 t检验 ,两组测定值无显著性差异 ,采样器代替人工采样完全可行。污水自动采样器代替人工采样的可行性分析@荆万钧$抚顺市环境监测站!…     

一种淡水大型底栖无脊椎动物采样器研究

研制出一种长方体的十字筐采样器,在采样器内分别填装石、砂、底泥和水草4种基质,利用大型底栖无脊椎动物对生境的选择性进行样本被动采集。基质越多,采样器采集的生物种类越多,生物量也更丰富。用新研制的十字筐采样器和传统的篮式采样器对松花江流域7个采样点进行大型底栖无脊椎动物对比采样,结果显示:十字筐采样器是一种优良的采样器,适合在松花江流域乃至全国推广应用。     

大水量采样器,采样技术在环境监测中的应用

在环境监测工作中,采样是重要步骤,一些先进国家的环境保护机构对发展水中痕量污染物的富集采样技术极为重视,自动采样器(装置)得到广泛应用.美国国家环保局(EPA)下属的辛辛那提环境监测与支持实验室编著的《水与废水采样及样品保存手册》一书,专门介绍了一些自动采样器,认为自动采样器的使用为进行环境污染监测和筛选环境水样中的优先监测物和致突变物质,提供了方便,使过去因工作量大而无法广泛开展的工作成为可能.采样器以及采样技术的发展水平反映了一个国家环境监测水平.     

废水自动采样器存在偏差原因分析及解决方法

简述了废水自动采样器应用现状。根据废水自动采样器性能指标要求,分析了自动采样器在验收和使用过程中应当重视的几个因素。并通过系列的比对、调查,对机器采样和手工采样可能引起监测结果有所偏差的几个方面进行了探讨,提出了解决这些偏差的一些方法和建议。     

负压式水质采样器的研制及应用

概述了我国目前水质采样技术规范和水质采样器的现状 ;阐述了负压式水质采样器的结构组成、工作原理及采样方法。该采样器不需电源、携带方便 ,可有效地控制采样深度并实现分层采样。     

环境空气连续采样系统的改进

目前 ,很多环境监测站已采用 2 4ｈ连续采样监测代替了过去的季五日采样法。连续采样监测系统由空气自动连续采样器、总悬浮颗粒物 (ＴＳＰ)采样器和辅助风机 (主要是采样管道引风机和采样亭排气扇 )组成。空气连续采样器设有时控系统 ,可以根据要求随时启停 ,ＴＳＰ采样器无隔日采样控制系统 ,辅助风机则经常出现仪器停止采样后继续运转的情况。对此 ,今利用空气连续采样器的时控系统 ,增加一个ＣＪ1 0 - 5型交流接触器 ,实现了对采样系统所有设备的控制 ,使之都能按要求启停 ,从而节约了用电量 ,减少了风机的不必要运转。现采用的是ＨＢ -…     

被动采样监测环境空气中SO2和NO2

用自主研制的采样管开展环境空气中SO2和NO2的被动采样监测.结果表明,被动采样监测结果与自动监测结果高度相关,经回归方程修正后,两者的结果没有显著性差异,被动采样的采样和分析产生的误差得以消除.     

Field intercomparison of diffusive samplers for measuring ammonia

Agricultural production systems are recognised as a major source of atmospheric ammonia. Deposition of ammonia and ammonium may contribute to undesired changes in oligotrophic ecosystems. The continuous measurement of atmospheric ammonia requires expensive and sophisticated techniques and is performed only in a very restrict number of ambient air stations in Europe. Therefore, the application of passive samplers, which have the advantage of being easy to handle and cost-efficient, is useful. In the past the comparability of different passive samplers must be considered as rather scarce. In a joint European project under the leadership of the GSF-Forschungszentrum für Umwelt und Gesundheit, Neuherberg, in 1997 a comparison of different passive ammonia monitoring methods was carried out in a prealpine rural site near Garmisch-Partenkirchen. It was considered valuable to include not only well established systems but also methods still being developed. For the comparative test ten working groups with different methods took part. A wet annular denuder system, which has been developed by the Netherlands Energy Research Foundation for on-line measurement of atmospheric ammonia, served as reference of passive methods. The experiment, which started in June and finished in December, showed that most of the passive samplers fulfil the requirements and can be recommended for further measurements. Additional measurements of meteorological parameters were performed to check the influences of different weather conditions on passive sampling.     

Baseline ambient gaseous ammonia concentrations in the Four Corners area and eastern Oklahoma, USA

Ambient ammonia monitoring using Ogawa passive samplers was conducted in the Four Corners area and eastern Oklahoma, USA during 2007. The resulting data will be useful in the multipollutant management of ozone, nitrogen oxides, and visibility (atmospheric regional haze) in the Four Corners area, an area with growing oil/gas production and increasing coal-based power plant construction. The passive monitoring data also add new ambient ammonia concentration information for the U.S. and will be useful to scientists involved in present and future visibility modeling exercises. Three week integrated passive ammonia samples were taken at five sites in the Four Corners area and two sites in eastern Oklahoma from December, 2006 through December, 2007 (January, 2008 for two sites). Results show significantly higher regional background ammonia concentrations in eastern Oklahoma (1.8 parts per billion (ppb) arithmetic mean) compared to the Four Corners area (0.2 ppb arithmetic mean). Annual mean ammonia concentrations for all Four Corners area sites for the 2007 study ranged from 0.2 ppb to 1.5 ppb. Peak ambient ammonia concentrations occurred in the spring and summer in both areas. The passive samplers deployed at the Stilwell, Oklahoma site compared favorably with other passive samplers and a continuous ammonia monitoring instrument.     

化学吸收法采集固定污染源氨气的影响因素探究

固定污染源氨气的手工监测,干扰因素较多,其中采样环节尤为关键。实验通过催化氧化-化学发光法考察不同采样管线材质对氨气的吸附效果,离子色谱法考察化学吸收法采集氨气的吸收瓶类型、采样流量、吸收液种类、吸收液浓度及体积等采样条件对氨气吸收效率的影响。实验表明,316 L不锈钢与聚四氟乙烯对氨气的吸附较小,氨气的采样流量不宜超过1.0 L/min,棕色气泡式吸收瓶更适用于氨气样品的采集,磷酸溶液作吸收液对氨气的吸收效率较好,对于低浓度的氨气样品,应采用低流量长时间采集。     

Determining the agricultural ammonia immission using bark bio-monitoring: comparison with passive sampler measurements

Bark samples of spruce, pine and oak trees were collected at two sites in southern Bavaria which are characterized by high agricultural ammonia emissions. The samples were taken using a recently developed bark sampling device which removes a defined layer of the bark. The bark was then analysed for ammonium concentration in order to reflect the environmental ammonia immission. The measured bark concentrations decreased with rising distance between the sample trees and the ammonia source. This applied (i) to measurements inside a closed forest stand ranging from forest edge with high immission to forest interior with much lower immission, and (ii) to the open field where single-standing trees were sampled. Comparing the ammonium concentrations among the three different tree species revealed significant correlations. Thus, it could be shown that old spruce trees are as usable for bark bio-monitoring as the traditionally used pine and oak trees. The ammonium concentrations of the bark were significantly correlated to measurements taken by ammonia passive samplers at the same locations. These results indicate that bark samples may be used for a standardised monitoring of airborne ammonia load. A major advantage of the technique is the determination of the long-term accumulative ammonia load using a single measurement.     

Chemcatcher and DGT passive sampling devices for regulatory monitoring of trace metals in surface water

This work aimed to evaluate whether the performance of passive sampling devices in measuring time-weighted average (TWA) concentrations supports their application in regulatory monitoring of trace metals in surface waters, such as for the European Union's Water Framework Directive (WFD). The ability of the Chemcatcher and the diffusive gradient in thin film (DGT) device sampler to provide comparable TWA concentrations of Cd, Cu, Ni, Pb and Zn was tested through consecutive and overlapping deployments (7-28 days) in the River Meuse (The Netherlands). In order to evaluate the consistency of these TWA labile metal concentrations, these were assessed against total and filtered concentrations measured at relatively high frequencies by two teams using standard monitoring procedures, and metal species predicted by equilibrium speciation modeling using Visual MINTEQ. For Cd and Zn, the concentrations obtained with filtered water samples and the passive sampling devices were generally similar. The samplers consistently underestimated filtered concentrations of Cu and Ni, in agreement with their respective predicted speciation. For Pb, a small labile fraction was mainly responsible for low sampler accumulation and hence high measurement uncertainty. While only the high frequency of spot sampling procedures enabled the observation of higher Cd concentrations during the first 14 days, consecutive DGT deployments were able to detect it and provide a reasonable estimate of ambient concentrations. The range of concentrations measured by spot and passive sampling, for exposures up to 28 days, demonstrated that both modes of monitoring were equally reliable. Passive sampling provides information that cannot be obtained by a realistic spot sampling frequency and this may impact on the ability to detect trends and assess monitoring data against environmental quality standards when concentrations fluctuate.     

A New All Season Passive Sampling System for Monitoring Ozone in Air

A new all season passive sampling system for monitoring O₃ in the atmosphere has been developed in the laboratory and validated in the field. The unique features for this system include a newly designed passive sampler and a rain shelter, which allow the passive sampler to be installed in the field facing downwards. An equation associated with meteorological parameters is used to calculate the passive sampling rates. This system has been extensively tested in the lab (temperature from –18 to 20°C, relative humidity from 13 to 81%, and wind speed from 0.5 to 150 cm/s) and validated in the field in climates of all seasons. The accuracy of the ozone concentrations in the atmosphere obtained with the use of the new passive sampling system was higher than 85% compared to those obtained with continuous ozone analyzers. The new ozone passive sampling system can be used to measure ambient O₃ concentrations ranging from 3 ppb to 1000 ppb based on one-day exposure and 0.1 ppb to 140 ppb for a monthly exposure period. It is also reasonable to conclude that the new passive sampling system can be used for eight-hour exposure study because of the low field blanks and high sampling rates.     

A passive sampling method to determine ammonia in ambient air

Ambient ammonia concentrations, mainly originating from agricultural activities, have increased in the last few decades in Europe. As a consequence, critical loads on oligotrophic ecosystems such as forests and mires are greatly exceeded. Monitoring of ambient ammonia concentrations is necessary in order to investigate source-receptor relationships. Measuring ambient ammonia concentrations continuously with high time resolution is very expensive and cost-efficient systems are required. Where time resolution is of minor importance, several cost-effective systems, mainly dry denuder and passive samplers, can be applied. In this paper the Zürcher passive sampler, a diffusive sampling system, is presented. It is a Palmes type sampler with an acidic solution as absorbent and is easy to handle. It was tested at 46 sites in Switzerland over one year. The average concentration in ambient air was 2.5 microg m(-3) +/- 0.4 microg m(-3). The average of the blank values were 0.21 microg m(-3). The detection limit (double the standard deviation of the blank values) was 0.36 microg m(-3). Three passive samplers were exposed at each site and each period. The mean standard deviation of these triplicate measurements was 9.5%. Compared with a discontinuous tubular denuder system and a continuous annular denuder system, the deviation was less than 10%. The Zürcher passive sampler is a useful and cost-efficient tool to determine long-term average ammonia concentrations (one- to four-week periods) in ambient air for mean concentrations above 1 microg m(-3).