Di-(2-ethylhexyl)phthalate in sewage sludge and post-treated sludge: quantitative determination by HRGC-MS and mass spectral characterization

DEHP was quantified into sewage sludge, thermally dried sludge and compost samples from different areas of Catalonia (North East Spain) using high-resolution gas chromatography (HRGC) coupled to a mass spectrometry (MS). The aim of the work was to determine the evolution of this ubiquitous environmental contaminant along some post-treatment sludge processes, such as composting and thermally drying. DEHP concentration detected in some sludges are above the maximum limit suggested by the EC (100 ppm d.m.) for agricultural use. However, the composting and thermally drying reduce the amount of DEHP in sewage sludge to acceptable level for safe land application. The study was completed with the characterization and long-term observation of DEHP in sewage sludge, composted sludge and thermally dried sludge mixed with two types of soils. In all cases, the percentage of DEHP degraded was higher than 50% after 9 months of incubation.     

Priority organic pollutant assessment of sludges for agricultural purposes

A comprehensive characterization of five of the seven priority organic pollutants listed in the draft of the "Working document on sludge" [EU, 2000. Working Document on Sludge 3rd Draft. Unpublished, 19 p] has been carried out during 2001-2003 in sludge samples from Catalonia (NE Spain). One hundred and thirty-nine samples belonging to 20 Waste Water Treatment Plants (WWTPs), seven sludge treatment (thermal drying) and three composting sludge plants were taken in order to determine the concentration of polychlorinated dibenzo-p-dioxins and -furans (PCDD/Fs), di-2-(ethyl-hexyl)-phthalate (DEHP), nonylphenol and nonylphenol ethoxylates with one or two ethoxy groups (NPE), polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). PCDD/F concentrations were in general lower than the 100 ng I-TEQ/kg limit suggested in the above-mentioned document. In the same way, 98.5% for PCBs, 97% for PAH and 92.8% for DEHP of the samples presented concentrations lower than 0.8 mg/kg dm, 6 mg/kg dm and 100 mg/kg dm, respectively. In contrast, the vast majority of samples contained NPE concentrations much higher than 50mg/kg dm limit. The values ranged from 14.3 to 3150 mg/kg dm (median value=286.6 mg/kg) being composted sludge samples the less contaminated ones (17.9-363.4 mg/kg dm; median value=89.3 mg/kg). Special attention should be paid to the Catalan sludge NPE contamination owing to the high levels detected.     

Effect of drying and composting biosolids on the movement of nitrate and phosphate through repacked soil columns under steady-state hydrological conditions

Effects of two "enhanced" treatments (drying and composting mesophilic anaerobically digested (MAD) biosolid) on nutrient leaching were investigated. Repacked sandy or sandy loam textured soil cores amended with fresh, dried and composted MAD biosolid (250 kg N ha(-1)), were investigated under steady-state hydrological conditions. Two 24 h, 4.5 mm h(-1) rainfall events, with a 14-day interval, were simulated using water-tracers. Losses of nitrate from the sandy loam soil during rainfall event 1 (43.9-68.0 mg kg(-1)) were significantly greater (P < or = 0.05) than during event 2 (6.4-11.9 mg kg(-1)). Phosphate losses were significantly greater (P < or = 0.05) during event 2 (up to 0.30 mg kg(-1)) compared to the first (< 0.05 mg kg(-1)). The sand soil showed similar effects. Losses of nitrate-N (percentage of total N applied) from the sand soil were small (around 0.06% for fresh/dried and 0.63% for composted MAD biosolids). Losses of nitrate-N from the sandy loam soil were greater; 4% for fresh and dried and 3% for composted MAD biosolids. This research showed that drying MAD biosolid had little impact on nitrate and phosphate losses from soil compared to fresh MAD biosolid. The effect of composting MAD biosolid on nutrient losses was more variable.     

Fate of nitrogen during composting of chicken litter

Chicken litter (a mixture of chicken manure, wood shavings, waste feed, and feathers) was composted in forced-aeration piles to understand the changes and losses of nitrogen (N) during composting. During the composting process, the chemical [different N fractions, organic matter (OM), organic carbon (C), and C:N ratio], physical, and microbial properties of the chicken litter were examined. Cumulative losses and mass balances of N and organic matter were also quantified to determine actual losses during composting. The changes in total N concentration of the chicken litter piles were essentially equal to those of the organic N. The inorganic N concentrations were low, and that organic N was the major nitrogenous constituent. The ammonium (NH(4)(+))-N concentration decreased dramatically during first 35 days of composting. However, the rapid decrease in NH(4)(+)-N during composting did not coincide with a rapid increase in (NO(3)(-)+NO(2)(-))-N concentration. The concentration of (NO(3)(-)+NO(2)(-))-N was very low (<0.5 g kg(-1)) at day 0, and this level remained unchanged during the first 35 days of composting suggesting that N was lost during composting. Losses of N in this composting process were governed mainly by volatilization of ammonia (NH(3)) as the pile temperatures were high and the pH values were above 7. The narrow C:N ratio (<20:1) have also contributed to losses of N in the chicken litter. The OM and total organic C mass decreased with composting time. About 42 kg of the organic C was converted to CO(2). On the other hand, 18 kg was lost during composting. This loss was more than half (59%) of the initial N mass of the piles. Such a finding demonstrates that composting reduced the value of the chicken litter as N fertilizer. However, the composted chicken contained a more humified (stabilized) OM compared with the uncomposted chicken litter, which would enhance its value as a soil conditioner.     

Experimental assessment of bio-reduction of di-2-thylhexyl phthalate (DEHP) under aerobic thermophilic conditions

The reduction of organic contaminants in sewage sludge is of great importance for a further sludge disposal or agricultural utilization. Laboratory scale batch experiments were performed to assess the potential use of the aerobic thermophilic treatment technique to reduce the concentration of difficult to degrade organic chemicals. Di-2-ethylhexyl phthalate (DEHP) was chosen as a model representative of these chemicals. The effect of the sludge temperature and aeration rate on the reduction of DEHP concentration as well as on the reduction of the organic dry solid (oDS) was investigated. With a specific air flow rate of 16 m3/m3.h and a thermophilic temperature of 63 degrees C it was possible to achieve up to 70% reduction of the DEHP concentration and 61% of oDS within 96 hours. The maximum degradation of the oDS matter occurred within the first 24 hours of operation whereby only little oDS was degraded afterward. During the experiments the reactor content was routinely monitored for pH, COD, along with the ammonia nitrogen and orthophosphate concentrations.     

Correlation between inorganic (heavy metals) and organic (PCBs and PAHs) micropollutant concentrations during sewage sludge composting processes

The nature and congener composition of PCBs and PAHs present in sewage sludge composting processes was investigated. These studies included analysis of the most significant process parameters (such as pH, temperature, weight percentage variation) and in addition heavy metals whose typical composting speciation and behaviour were also considered in order to better understand organic compound time profiles. The significant correlation found between Pb, Cd, Cu and PCBs and between PAHs and Hg implies that quite a strong adsorption of PCBs onto organic matter takes place and also provides evidence for the volatilisation of PAHs. Chemical characteristics of inorganic species and organic compounds are summarised to account for the observed correlation and time trend profiles. Moreover, single congener concentrations demonstrate that the number of Cl substituents for PCBs and condensed benzene rings for PAHs determine to what extent they can be broken down for biodegradation and removed through volatilisation respectively.     

Removal of DEHP in composting and aeration of sewage sludge

The potential of composting and aeration to remove bis(2-ethylhexyl) phthalate (DEHP) from municipal sewage sludge was studied with two dewatered sludges: raw sludge and anaerobically digested sludge. Composting removed 58% of the DEHP content of the raw sludge and 34% of that of the anaerobically digested sludge during 85 days stabilisation in compost bins. A similar removal for the anaerobically digested sludge was achieved in a rotary drum in 28 days. Less than 1% of DEHP was removed with the compost leachate. Although DEHP removal was greater from raw sludge compost than anaerobically digested sludge compost, the total and volatile solids removals were on the same level in the two composts. In the aeration of raw sludge at 20 degrees C the DEHP removals were 33-41% and 50-62% in 7 and 28 days, respectively. Both composting and aeration are concluded to have the potential to reduce the DEHP contents typically found in sewage sludges to levels acceptable for agricultural use.     

Organic micropollutants’ distribution within sludge organic matter fractions explains their dynamic during sewage sludge anaerobic digestion followed by composting

The simultaneous fate of organic matter and 4 endocrine disruptors (3 polycyclic aromatic hydrocarbons (PAHs) (fluoranthene, benzo(b)fluoranthene, and benzo(a)pyrene) and nonylphenols (NP)) was studied during the anaerobic digestion followed by composting of sludge at lab-scale. Sludge organic matter was characterized, thanks to chemical fractionation and 3D fluorescence deciphering its accessibility and biodegradability. Total chemical oxygen demand (COD) removal was 41% and 56% during anaerobic digestion and composting, respectively. 3D fluorescence highlighted the quality changes of organic matter. During continuous anaerobic digestion, organic micropollutants’ removal was 22?±?14%, 6?±?5%, 18?±?9%, and 0% for fluoranthene, benzo(b)fluoranthene, benzo(a)pyrene, and nonylphenols, respectively. Discontinuous composting allowed to go further on the organic micropollutants’ removal as 34?±?8%, 31?±?20%, 38?±?10%, and 52?±?6% of fluoranthene, benzo(b)fluoranthene, benzo(a)pyrene, and nonylphenols were dissipated, respectively. Moreover, the accessibility of PAH and NP expressed by their presence in the various sludge organic matter fractions and its evolution during both treatments was linked to both the quality evolution of the organic matter and the physicochemical properties of the PAH and NP; the presence in most accessible fractions explained the amount of PAH and NP dissipated.

     

Effects of lime amendment on availability of heavy metals and maturation in sewage sludge composting

A batch composting study was performed to evaluate the feasibility of co-composting sewage sludge with lime, aiming at reducing the availability of heavy metals in the sludge compost. Sewage sludge with sawdust as bulking agent was amended with lime at 0, 0.63, 1.0, and 1.63% w/w, and composted for 100 days in laboratory batch reactors. The changes in temperature, pH, electrical conductivity (EC), and extractable heavy metal contents were measured while compost maturity was determined by C/N(organic) and cress seed germination during the composting period. Liming raised pH of compost effectively at the initial stage of composting and caused a decrease in EC through precipitation of soluble ions. Lime amendment also significantly reduced water-soluble and Diethylene triamine pentracetic acid (DTPA)-extractable metal contents. The maximum reductions were 60 and 40% for Cu, 80 and 40% for Mn, 55 and 10% for Zn, and 20 and 25% for Ni at the end of the composting period for the lime-amended sludge as compared to the control. In spite of the inhibitory effect of lime amendment on the decomposition activity of sewage sludge, all treatments reached maturation after 63 days of composting as indicated by the results of C/N(organic) ratio and cress seed germination test results. A lime amendment of < or =1.0% is recommended to co-compost with sewage sludge.     

Co-composting of paper mill sludge and hardwood sawdust under two types of in-vessel processes

Recycling of organic residues by composting is becoming an acceptable practice in our society. Co-composting dewatered paper mill sludge (PMS) and hardwood sawdust, two readily available materials in Canada, was investigated using uncontrolled and controlled in-vessel processes. The composted materials were characterized for total C and N, water-soluble, acid-hydrolyzable, and non-hydrolyzable N, extractable lipids, and by Fourier Transform Infrared (FT-IR) spectrophotometry. In the controlled scale process, the loss of organic matter was approximately 65% higher than in the uncontrolled process. After undergoing initial fluctuations in N fractions during the first two days of composting, by the end of the process, concentrations of water-soluble N decreased while those of acid-hydrolyzable and nonhydrolyzable N increased in the controlled process, whereas in the uncontrolled process, water-soluble N increased, but N in the other two fractions decreased continuously, indicating that the biochemical transformations of organic matter were not completed. Data on extractable lipids and FT-IR spectra suggest that the compost produced from the controlled process was bio-stable after 14 days, while the uncontrolled process was not stabilized after 18 days. In addition, FT-IR data suggest the biological activity during composting centered mainly on the degradation of aliphatic structures while aromatic structures were preserved. The co-composting of the PMS and hardwood sawdust can be successfully achieved if aeration, moisture, and bio available C/N ratios are optimized to reduce losses of N.     

Co-composting of Paper Mill Sludge and Hardwood Sawdust Under Two Types of In-Vessel Processes

Abstract

Recycling of organic residues by composting is becoming an acceptable practice in our society. Co-composting dewatered paper mill sludge (PMS) and hardwood sawdust, two readily available materials in Canada, was investigated using uncontrolled and controlled in-vessel processes. The composted materials were characterized for total C and N, water-soluble, acid-hydrolyzable, and non-hydrolyzable N, extractable lipids, and by Fourier Transform Infrared (FT-IR) spectrophotometry. In the controlled scale process, the loss of organic matter was approximately 65% higher than in the uncontrolled process. After undergoing initial fluctuations in N fractions during the first two days of composting, by the end of the process, concentrations of water-soluble N decreased while those of acid-hydrolyzable and nonhydrolyzable N increased in the controlled process, whereas in the uncontrolled process, water-soluble N increased, but N in the other two fractions decreased continuously, indicating that the biochemical transformations of organic matter were not completed. Data on extractable lipids and FT-IR spectra suggest that the compost produced from the controlled process was bio-stable after 14 days, while the uncontrolled process was not stabilized after 18 days. In addition, FT-IR data suggest the biological activity during composting centered mainly on the degradation of aliphatic structures while aromatic structures were preserved. The co-composting of the PMS and hardwood sawdust can be successfully achieved if aeration, moisture, and bio-available C/N ratios are optimized to reduce losses of N.     

Leaching of heavy metals and alkylphenolic compounds from fresh and dried sewage sludge

Reusing sewage sludge as a soil fertiliser has become a common alternative to disposal. Although this practice has a few benefits, it may contribute to the medium- and long-term contamination of the trophic chain because sewage sludge may contain heavy metals and organic contaminants. As the leaching of contaminants may depend on the sludge pre-treatment, the leaching of heavy metals (Cu, Ni, Pb, Zn and Cr) and alkylphenolic compounds (APCs) (octylphenol (OP), nonylphenol (NP), nonylphenol-mono-ethoxylate (NP₁EO)) was investigated in five fresh and 40 °C dried sewage sludge samples from north-eastern Spain. FT-IR analyses and full-scan GC-MS chromatograms showed that sludge drying changed the nature of organic compounds leading to changes in their solubility. Moreover, sludge drying led to a higher relative contribution of dissolved organic carbon than the particulate organic carbon in the leachates. Leaching of Pb, Zn and Cr was below 5 % in both fresh and dried sludge samples, whereas Cu and Ni leached at rates up to 12 and 43 %, respectively, in some of the dried sludge samples. The leaching yields of OP, NP and NP₁EO ranged from 1.3 to 35 % for fresh samples, but they decreased from 0.8 to 3.4 % in dried samples. The decrease in the leachability of APCs observed in dried sludge samples might be attributed to the fact that these compounds are associated with particulate organic matter, with significantly lower concentration or even absent in dried sludge than in fresh sludge samples. Therefore, it is recommended to dry the sludge before its disposal.     

Emissions of polychlorinated biphenyls (PCBs) from sludge drying beds to the atmosphere in Chicago

Ambient air PCB concentrations in the Lake Calumet region in Southeast Chicago have been found to be significantly higher than in nearby non-urban areas. This area is highly industrialized and also contains municipal sludge drying facilities and landfills. In an effort to quantify the importance of the sludge drying facilities to the elevated concentrations, upwind/downwind air samples from the Calumet East sludge drying bed were obtained between April and October 2002. For these samples, the downwind minus upwind (downwind-upwind) concentration varied from 0.33 to 1.27ngm(-3) for non-northeast (NE) direction winds suggesting sludge drying is a source of PCBs to the atmosphere. However, the upwind concentrations were higher than the downwind for winds from the NE of the sampling site suggesting more significant source(s), possibly Lake Calumet or the so called "Cluster site" NE of the sludge drying beds. Flux chamber experiments carried out during the sampling period measured average PCB fluxes of 210ngm(-2)h(-1) (range 43-910ngm(-2)h(-1)) which resulted in an overall flux of 0.005kgday (d)(-1) ( approximately 2kgyr(-1)). A developed regression equation between moisture content and sludge concentration estimated higher PCB losses of 0.26kgd(-1) ( approximately 95kgyr(-1)). Although these two approaches yielded different values, they both indicate that the emission from the Calumet East sludge drying beds were of minimal importance when compared to the total estimated amount of 2-70kgd(-1) (700-2100kgyr(-1)) of PCBs entering the Chicago atmosphere.     

深圳市污水处理厂剩余污泥干化特性研究

对深圳市污水处理厂旱季和雨季的剩余污泥泥质进行了分析,并采用桨叶式污泥干化机对剩余污泥的干化特性及干化过程中的污染物排放特性进行了研究.结果表明,相对于雨季剩余污泥,旱季剩余污泥的干化速率总体更高,旱季剩余污泥在含水率由80％降至60％的干化阶段,干化速率比雨季剩余污泥约高1倍,而当含水率低于60％后,两者的干化速率基...     

The evaluation of stability during the composting of different starting materials: comparison of chemical and biological parameters

Three blends formed by: (i) food processing waste (CP(FP)), (ii) waste water sewage sludge (CP(WW)), and (iii) their mixture (CP(FP+WW)), blended with tree pruning as bulking agent, were composted over 3 months. During composting the blends were monitored for the main physical-chemical characteristics: temperature, oxygen saturation level (O(2)%), pH, total and volatile solids, total organic carbon, and organic nitrogen (N(org)). In addition to the main parameters, the dissolved organic carbon (DOC), the inorganic nitrogen and the Oxygen Uptake Rate (OUR) were monitored. All the mixtures easily reached a peak temperature around 70°C, related to the lowest O(2)%. After 90 d, CP(FP), CP(FP+WW), and CP(WW) showed an organic matter mineralization of 43%, 35% and 33%, respectively; CP(FP) fitted an exponential model while both CP(FP+WW), and CP(WW) fitted a logistic model. During composting an OUR reduction of 79%, 78% and 73% was registered in CP(FP), CP(FP+WW), and CP(WW), respectively; the OUR successfully fitted the adopted exponential model and well reflected the stabilization process in time. The N(org) recovery at the end of the process was positive only in CP(WW) (11.6%). The DOC significantly decreased during the composting process but did not successfully fit any model. The mineral nitrogen did not follow the typical pattern with NH(4)(+) disappearance and NO(3)(-) accumulation. Strong NO(3)(-) losses were evident in all blends, while NH(4)(+) accumulations were detectable only in CP(FP), and CP(FP+WW). The NH(4)(+)/NO(3)(-) ratio did not satisfactorily reflect the composting process over time. The comparison of the first order (exponential) and logistic (sigmoidal) models applied to the OUR and OM course highlights the role of mineral nitrogen as limiting factor during composting of the more stabilized sludge.     

Organic Contaminants from Sewage Sludge Applied to Agricultural Soils. False Alarm Regarding Possible Problems for Food Safety? (8 pp)

Goal, Scope and Background Sewage sludge produced in wastewater treatment contains large amounts of organic matter and nutrients and could, therefore, be suitable as fertiliser. However, with the sludge, besides heavy metals and pathogenic bacteria, a variety of organic contaminants can be added to agricultural fields. Whether the organic contaminants from the sludge can have adverse effects on human health and wildlife if these compounds enter the food chain or groundwater still remains a point of controversial discussion. Main Features This paper presents an overview on the present situation in Europe and a summary of some recent results on the possible uptake of organic contaminants by crops after addition to agricultural fields by sewage sludge. Results Greenhouse experiments and field trials were performed to study the degradation and uptake of organic micro-contaminants in sludge-amended agricultural soil in crops, such as barley and carrots grown in agricultural soil amended with anaerobically-treated sewage sludge from a wastewater treatment plant, but studies hitherto have revealed no immediate risks. Common sludge contaminants such as linear alkylbenzene sulphonates (LAS), nonylphenol ethoxylates (NPE), polycyclic aromatic hydrocarbons (PAH), bis(diethylhexyl) phthalate (DEHP), showed neither accumulation in soil nor uptake in plants. Discussion It is assumed that the annual amount of sewage sludge produced in Europe will increase in the future, mainly due to larger amounts of high quality drinking water needed by an increasing population and due to increasing demands for cleaner sewage water. Application of sewage sludge to agricultural soils is sustainable and economical due to nutrient cycling and disposal of sewage sludge. However, this solution also involves risks with respect to the occurrence of organic contaminants and other potentially harmful contents such as pathogens and heavy metals present in the sludge. There have been concerns that organic contaminants may accumulate in the soil, be taken up by plants and thereby transferred to humans via the food chain. Results obtained so far revealed, however, no immediate risk of accumulation of common organic sludge contaminants in soil or uptake in plants when applying sewage sludge to agricultural soil. With very high dosages of sewage sludge, there may be a risk for accumulation of very apolar contaminants, such as DEHP, to the soil. Conclusions Any conclusions on the safe use of sewage sludge in agriculture have to be drawn carefully, as the studies performed until now have been limited. Further studies are required, and before final statements can be drawn, it is imminent to study a larger variety of common crops and the effect sewage sludge application may have on a possible accumulation of organic contaminants in the crops. Furthermore, a larger variety of organic contaminants need to be studied and special focus should be given to contaminants newly introduced into the environment. Besides investigating possible plant uptake of organic contaminants, the fate of these compounds in soil after sludge application need to be monitored too. Here, special attention has to begiven to studies on degradation and the formation of degradation products, to weathering and to leaching effects on groundwater, to the application of different crops on the same field (crop rotation), to the use of full-width tillage and strip tillage, and to long term application of sewage sludge on the soil. Recommendations and Perspectives There are environmental, political as well as economical incentives to increase the agricultural application of sludge. However, such usage should be performed with care as there are also ways in which sludge fertilisation could harm the environment and human health. Recently, a new European COST Action (859) has been established covering the field of food safety and improved food quality. Part of the Action is dealing with the application of sewage sludge in agriculture. Before any political and economical measures can be taken, the pros and cons have to be sufficiently investigated on a scientific level first. ESS-Submission Editor: Prof. Elena Maestri (elena.maestri@unipr.it)     

Analysis of 4-nonylphenols, phthalates, and polychlorinated biphenyls in soils and biosolids

When sewage sludge is added to agricultural land, organic chemicals contaminants are also added. The fate of these chemicals, particularly those shown to have oestrogenic potential, has received much research and regulatory interest in recent years. A method was developed for the analysis of 4-nonylphenols, phthalates, and PCB congeners in soils, mesophilic anaerobially digested dewatered (MADD) sewage sludge, and MADD sludge-amended soil. After Soxhlet-extraction, the 4-nonylphenols and phthalates were separated from the PCBs on an isolute cyanopropyl SPE cartridge and analysed by GC-MS directly. The PCBs were acid treated on a Bakerbond PCB-A cartridge, then passed through a gel filtration column of Biobeads SX-3 resin, before GC-MS analysis. The method was successfully validated and then used for routine analysis, where average recoveries of the surrogate standards were 83+/-17% (4-n-heptylphenol), 96+/-11% (dimethyl-tere-phthalate), 101+/-12% (dibenzyl-phthalate), and 79+/-13% (PCBs 6, 54, 104, 155, and 198).     

Effect of turning frequency on co-composting pig manure and fungus residue

Composting of agricultural wastes not only can reduce environmental pollution caused by improper disposal, but also can recycle agricultural wastes and transform them into highly valuable products, such as fertilizers or soil conditioners, for agricultural applications. However, the composting process and final product are easily affected by the limited oxygen supply that results from insufficient aeration, especially in the center of a large-scale windrow. Hence, a pilot-scale experiment was conducted to investigate the effects of the turning frequency on the composting efficiency and compost quality of used pig manure and fungus residue. Physical and chemical characteristics were measured over the course of 63 days of composting. The data indicate that higher temperatures and more rapid moisture removal generally result from a turning treatment of once every 2–4 days than in fewer, or no, turning treatments. The total nitrogen, total phosphorus, and total potassium contents increased in all windrows as the organic matter content decreased, but both the increases and decrease were greater in windrows that were turned more frequently. The reduction of the organic matter mass by 53.7–66.0% for a turning of once every 2–8 days is significantly higher than that for the static windrow (39.1%). Although there is an increase in nitrogen mass loss with an increased turning frequency, lower nitrogen mass losses (12.7–25.7%) in all treatments were noted compared with previous studies. A final compost product with less moisture, less weight, higher nutrient content (N, P, and K), and greater stability was obtained in windrows with turning frequencies of once every 2–4 days, which is recommended when composting pig manure and fungus residue.

Implications: Composting of agricultural wastes not only can reduce environmental pollution caused by improper disposal, but recycling of agricultural wastes transforms them into highly valuable products, such as fertilizers or soil conditioners, for agricultural applications. However, the composting process and final product are easily affected by the limited oxygen supply that results from insufficient aeration, especially in the center of a large-scale windrow. Hence, a pilot-scale experiment was conducted to investigate the effects of the turning frequency on the composting efficiency and compost quality of used pig manure and fungus residue, so as to capture an operational technique suitable for the effective co-composting pig manure and edible fungi residue for a large-scale composting plant.     

Fate of PCBs, PAHs and their source characteristic ratios during composting and digestion of source-separated organic waste in full-scale plants

Composting and digestion are important waste management strategies. However, the resulting products can contain significant amounts of organic pollutants such as polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs). In this study we followed the concentration changes of PCBs and PAHs during composting and digestion on field-scale for the first time. Concentrations of low-chlorinated PCBs increased during composting (about 30%), whereas a slight decrease was observed for the higher chlorinated congeners (about 10%). Enantiomeric fractions of atropisomeric PCBs were essentially racemic and stable over time. Levels of low-molecular-weight PAHs declined during composting (50-90% reduction), whereas high-molecular-weight compounds were stable. The PCBs and PAHs concentrations did not seem to vary during digestion. Source apportionment by applying characteristic PAH ratios and molecular markers in input material did not give any clear results. Some of these parameters changed considerably during composting. Hence, their diagnostic potential for finished compost must be questioned.     

Changes of polycyclic aromatic hydrocarbons during composting of sewage sludges with chosen physico-chemical properties and PAHs content

The aim of the experiment was to determine changes in the PAH content during sewage sludge composting. The extent was evaluated to which sewage sludge properties influences on PAHs losses during composting. Five municipal sewage sludges were studied from sewage treatment plants located in the south-east of Poland, i.e. in Stalowa Wola, Kra?nik, Lublin, Zamo?? and Bi?goraj. The treatment plants selected were characterised by their differentiation with catchments area as well as the industrial character of the areas. Sludge composting was carried out in aerobic conditions in plastic containers for a period of 76 days. The content of 14 polycyclic aromatic hydrocarbons (PAHs) and some physical-chemical (TOC, Nt, TOC/Nt, CEC, BS, TEB, pH, available potassium and phosphorus, total forms of cations) sewage sludge properties were monitored. In the present study correlations between PAHs losses (during various phases of composting) and physical-chemical properties of sewage sludges and composts were also evaluated. The sewage sludges were characterised both by differentiated properties and by PAH content. The total PAH content (the sum of 14 PAHs from the EPA List with exception of naphthalene and acenaphthene) in the sludges ranged from 3674 to 11236 microg kg(-1). Four- and three-ring compounds were predominant in the sewage sludges. Almost all of the sludges were characterised by differentiated content levels of both individual PAHs groups and PAHs sum. After 76 days of composting, a significant lowering of the PAH content was observed in all sludges as compared to the beginning of the experiment. The range of total observed PAH losses was from 15.8% to 48.6%, depending on the sewage sludge. The largest lowering of the PAH content was observed in the sludge with the lowest concentration of the xenobiotics studied. The largest losses in individual PAHs were observed in the case of five- and six-rings compounds, and were probably related to strong pollutant binding by other components of the sewage sludge. The few significant relationships showed that PAH losses during composting were only slightly determined by the analysed physical-chemical properties.