UV/Fenton氧化降解水溶液中甲基叔丁基醚的试验研究

采用UV／Fenton技术对污染水体中的甲基叔丁基醚（MTBE）进行了氧化降解试验。结果表明，在室温条件下，当H2O2为10mmol／L，FC＋为2mmol／L，pH为2．4时，起始摩尔浓度为1mmol／L的MTBE在30min内可去除99％；结果还显示了MTBE的降解分两个阶段，第一阶段是在UV／Fe^2＋／H2O2下的快速降解，第二阶段由于Fe^2＋的大量消耗而降解相对较慢。     

降解甲基叔丁基醚的PM1生物膜培养及性能研究

在pH值7.2～8.5、温度25℃、DO≥5 mg/L的条件下,用含有甲基叔丁基醚（MTBE）的模拟废水对Methylibium petroleiphilum PM1进行富集培养并在陶粒表面挂膜,进而对其特性、性能等进行了研究。填料表面生物膜MTBE降解的序批实验和电镜照片分析均表明陶粒表面已成功附着PM1高效降解菌形成的生物膜。在挂膜后期,当起始MTBE浓度为100～110 mg/L时,经过24 h,MTBE的去除率达到65%以上并基本稳定,其中挥发占4.6%,生物降解起主导的作用。     

甲基叔丁基醚降解菌的驯化与筛选

为了筛选降解甲基叔丁基醚(MTBE)的优势菌种,调查了不同来源土壤土著菌的降解潜力.应用不同的驯化方式以MTBE为惟一碳源,在好氧的条件下,驯化、筛选出高效降解混合菌株,为现场应用打好基础.并从中分离得到6株高降解性的单一菌株,对其进行了初步鉴定,为进一步研究其降解途径做好准备.对单一菌株与混合菌株的降解效果进行了比较.结果表明,混合菌株的降解效果要明显高于单一菌株.     

Chemical oxidative degradation of methyl tert-butyl ether in aqueous solution by Fenton's reagent

Degradation of methyl tert-butyl ether (MTBE) in aqueous solution by Fenton's reagent (Fe2+ and H2O2) was investigated. Effects of reaction conditions on the oxidation efficiency of MTBE by Fenton's reagent were examined in batch experiments. Under optimum conditions, 15 mM H2O2, 2 mM Fe2+, pH 2.8 and room temperature, the initial 1 mM MTBE solution was reduced by 99% within 120 min. Results showed that MTBE was decomposed in a two-stage reaction. MTBE was first decomposed swiftly based on a Fe2+/H2O2 reaction and then decomposed somewhat less rapidly based on a Fe3+/H2O2 reaction. The detection of Fe2+ also supported the theory of the two-stage reaction for the oxidation of MTBE by Fenton's reagent. The dissolved oxygen in the solution decreased rapidly in the first stage reaction, but it showed a slow increase in the second stage with a zero-order kinetics. A reaction mechanism involving two different pathways for the decomposition of MTBE by Fenton's reagent was also proposed. Chemicals including tert-butyl formate, tert-butyl alcohol, methyl acetate and acetone were identified to be the primary intermediates and by-products of the degradation processes.     

Biotic and abiotic transformations of methyl tertiary butyl ether (MTBE)

Background Methyl tertiary butyl ether (MTBE) is a fuel additive which is used all over the world. In recent years it has often been found in groundwater, mainly in the USA, but also in Europe. Although MTBE seems to be a minor toxic, it affects the taste and odour of water at concentrations of < 30 μg/L. Although MTBE is often a recalcitrant compound, it is known that many ethers can be degraded by abiotic means. The aim of this study was to examine biotic and abiotic transformations of MTBE with respect to the particular conditions of a contaminated site (former refinery) in Leuna, Germany. Methods Groundwater samples from wells of a contaminated site were used for aerobic and anaerobic degradation experiments. The abiotic degradation experiment (hydrolysis) was conducted employing an ion-exchange resin and MTBE solutions in distilled water. MTBE, tertiary butyl formate (TBF) and tertiary butyl alcohol (TBA) were measured by a gas chromatograph with flame ionisation detector (FID). Aldehydes and organic acids were respectively analysed by a gas chromatograph with electron capture detector (ECD) and high-performance ion chromatography (HPIC). Results and Discussion Under aerobic conditions, MTBE was degraded in laboratory experiments. Only 4 of a total of 30 anaerobic experiments exhibited degradation, and the process was very slow. In no cases were metabolites detected, but a few degradation products (TBF, TBA and formic acid) were found on the site, possibly due to the lower temperatures in groundwater. The abiotic degradation of MTBE with an ion-exchange resin as a catalyst at pH 3.5 was much faster than hydrolysis in diluted hydrochloric acid (pH 1.0). Conclusion Although the aerobic degradation of MTBE in the environment seems to be possible, the specific conditions responsible are widely unknown. Successful aerobic degradation only seems to take place if there is a lack of other utilisable compounds. However, MTBE is often accompanied by other fuel compounds on contaminated sites and anaerobic conditions prevail. MTBE is often recalcitrant under anaerobic conditions, at least in the presence of other carbon sources. The abiotic hydrolysis of MTBE seems to be of secondary importance (on site), but it might be possible to enhance it with catalysts. Recommendation and Outlook MTBE only seems to be recalcitrant under particular conditions. In some cases, the degradation of MTBE on contaminated sites could be supported by oxygen. Enhanced hydrolysis could also be an alternative. - * The basis of this peer-reviewed paper is a presentation at the 9th FECS Conference on 'Chemistry and Environment', 29 August to 1 September 2004, Bordeaux, France.     

地下水环境中甲基叔丁基醚运移过程的动力学模型

建立了地下水环境中甲基叔丁基醚(MTBE)运移过程的变系数动力学模型,并对模型进行了验证和参数灵敏度分析.模拟结果表明,地下水流速和阻滞系数对于MTBE的运移过程影响最为显著,而水动力弥散系数的影响较小,忽略其变化不会对预测地下水环境中污染物运移的环境动力学行为造成太大误差.由此得到的结论可定量研究MTBE在地下水环境中的对流.扩散特征,还可为MTBE污染地下水的预测预报、修复治理等研究提供科学依据.     

无铅汽油添加剂甲基叔丁基醚(MTBE)的环境化学行为及其分析方法

本文简要介绍了无铅汽油添加剂MTBE的物理化学性质、环境化学行为、地下水的污染状况和对动物的潜在致癌毒理 ,并对其分析方法作了综述 ,指出了我国开展MTBE有关研究的重要性。     

Microbial degradation of pharmaceuticals in estuarine and coastal seawater

Microbial degradation rates were measured for 19 pharmaceuticals in estuarine and coastal surface water samples. Antipyrine, carbamazepine, cotinine, sulfamethoxazole, and trimethoprim were the most refractory (half-lives, t_1/2 = 35 to >100 days), making them excellent candidates for wastewater tracers. Nicotine, acetaminophen, and fluoxetine were labile across all treatments (t_1/2 = 0.68-11 days). Caffeine, diltiazem, and nifedipine were also and relatively labile in all but one of the treatments (t_1/2 = 3.5-13 days). Microbial degradation of caffeine was further confirmed by production ¹⁴CO₂. The fastest decay of non-refractory compounds was always observed in more sewage-affected Jamaica Bay waters. Degradation rates for the majority of these pharmaceuticals are much slower than reported rates for small biomolecules, such as glucose and amino acids. Batch sorption experiments indicate that removal of these soluble pharmaceuticals from the water column to sediments is a relatively insignificant removal process in these receiving waters.     

中国甲基叔丁基醚污染现状及防治对策研究

甲基叔丁基醚(MTBE)因作为汽油添加剂大量使用而广泛存在于不同环境介质中。通过调研中国部分城市大气、土壤和水体环境介质中的MTBE污染情况,分析了中国目前MTBE的污染现状及影响。结果显示,中国城市区域附近不同环境介质中普遍存在MTBE污染,一般区域MTBE污染程度较轻,加油站周边环境中MTBE污染相对较重。部分加油站区域大气中的MTBE浓度已经超过可接受的健康风险水平;加油站周边地下水中的MTBE检出率较高,对地下水水质安全具有一定威胁。最后,对中国MTBE污染防治工作进行了总结并给出了相关建议。     

甲基叔丁基醚(MTBE)在不同粘性土壤中的吸附特性

土壤对有机物的吸附是污染土壤及地下水原位修复技术中的重要参数.通过静态间歇吸附实验研究了甲基叔丁基醚(MTBE)在不同粘性土壤中的吸附特性.结果表明,MTBE在粘性土壤中的吸附行为均可用线性方程很好描述,粘粒是土壤对MTBE吸附的主要影响因素,吸附常数与土壤粘粒含量呈y=4.382×10-3x-0.817 ×10-3直线关系.对不同温度下的吸附数据分析发现,粘性土壤对MTBE的平衡吸附量随温度的升高而降低,由吸附热力学推导可得等量吸附焓变△H与平衡吸附量无关,且△H＜0,表明该吸附为故热过程.     

Anaerobic biodegradation of methyl tert-butyl ether under iron-reducing conditions in batch and continuous-flow cultures.

The feasibility of biodegradation of the fuel oxygenate methyl tert-butyl ether (MTBE) under iron-reducing conditions was explored in batch and continuous-flow systems. A porous pot completely-mixed reactor was seeded with diverse cultures and operated under iron-reducing conditions. For batch studies, culture from the reactor was transferred anaerobically to serum bottles containing either MTBE alone or MTBE with ethanol (EtOH) and excess electron acceptor. In the continuous-flow reactor, MTBE conversion to tert-butyl alcohol (TBA) was observed after 181 days of operation, and stable removal was achieved throughout the remainder of the study. Simultaneously, both the MTBE only and the MTBE and EtOH iron-reducing batch serum bottles also began to degrade MTBE. Bottles were respiked and the degradation rate was determined to be 2.36 +/- 0.10 x 10(-4) mmol MTBE/min-kgVSS. The EtOH present with MTBE degraded faster (7.76 +/- 0.08 x 10(-3) mmol EtOH/min-kg VSS) but did not have a noticeable effect on the rate of MTBE degradation. No evidence of TBA degradation was observed by the iron-reducing cultures. Stoichiometry of iron utilization was determined from the iron balance of the continuous-flow reactor, and it was found that the bulk of the electron acceptor was required for energy and maintenance with little remaining for cell synthesis. This is consistent with a yield coefficient of less than 0.1. Molecular analysis of the iron-reducing culture by denaturing gradient gel electrophoresis indicated that uncultured strains of delta-Proteobacteria were dominant in the reactor.     

Simultaneous decontamination of hexavalent chromium and methyl tert-butyl ether by UV/TiO2 process

Hexavalent chromium and methyl tert-butyl ether (MTBE) are two important environmental pollutants. Simultaneous decontamination of Cr(VI) and MTBE was studied by UV/TiO2 process. The influences of pH and the concentrations of pollutants on the kinetics of the photocatalytic reactions were evaluated. Dark adsorption tests showed that the acidic pH favored the adsorption of Cr(VI) while neutral pH favored the adsorption of MTBE. Under UV irradiation, Cr(VI) reduction was observed in Cr(VI)/TiO2 system, and MTBE oxidation was observed in MTBE/TiO2 system. The system containing Cr(VI) and MTBE by UV/TiO2 process demonstrated the synergistic effect between oxidation of MTBE and reduction of Cr(VI). The results demonstrated that two pollutants Cr(VI) and MTBE could be eliminated simultaneously by UV/TiO2 process. tert-Butyl formate, tert-butyl alcohol and acetone were identified as primary degradation products of MTBE by gas chromatography-mass spectrometry in the degradation of MTBE by UV/TiO2 process.     

Biofilm formation and microbial activity in a biofilter system in the presence of MTBE, ETBE and TAME

Emerging water contaminants derived from unleaded gasoline such as methyl tert-butyl ether (MTBE), ethyl tert-butyl ether (ETBE) and tert-amyl methyl ether (TAME), are in need of effective bioremediation technologies for restoring water resources. In order to design the conditions of a future groundwater bioremediating biofilter, this work assesses the potential use of Acinetobacter calcoaceticus M10, Rhodococcus ruber E10 and Gordonia amicalis T3 for the removal of MTBE, ETBE and TAME in consortia or as individual strains. Biofilm formation on an inert polyethylene support material was assessed with scanning electron microscopy, and consortia were also analysed with fluorescent in situ hybridisation to examine the relation between the strains. A. calcoaceticus M10 was the best coloniser, followed by G. amicalis T3, however, biofilm formation of pair consortia favoured consortium M10-E10 both in formation and activity. However, degradation batch studies determined that neither consortium exhibited higher degradation than individual strain degradation. The physiological state of the three strains was also determined through flow cytometry using propidium iodide and 3′-dihexylocarbocyanine iodide thus gathering information on their viability and activity with the three oxygenates since previous microbial counts revealed slow growth. Strain E10 was observed to have the highest physiological activity in the presence of MTBE, and strain M10 activity with TAME was only maintained for 24 h, thus we believe that biotransformation of MTBE occurs within the active periods established by the cytometry analyses. Viable cell counts and oxygenate removal were determined in the presence of the metabolites tert-butyl alcohol (TBA) and tert-amyl alcohol (TAA), resulting in TBA biotransformation by M10 and E10, and TAA by M10. Our results show that A. calcoaceticus M10 and the consortium M10-E10 could be adequate inocula in MTBE and TAME bioremediating technologies.     

Sources, distribution and behaviour of methyl tert-butyl ether (MTBE) in the Tamar Estuary, UK

Negligible information is currently available concerning levels of the fuel additive methyl tert-butyl ether (MTBE) in European estuaries or coastal environments. MTBE was measured at selected potentially contaminated harbours and marinas, and throughout an axial transect of the Tamar Estuary, UK. Headspace solid-phase microextraction was used in combination with GC-MS for its determination. MTBE was detected in water samples from all stations at concentrations ranging from a few ng/l to a maximum of 194 ng/l (in a semi-enclosed harbour). Elevated levels were generally associated with motor vehicle and boating activities. The Tamar road and rail bridges provided a major input to the lower estuary, downstream of which conservative mixing appeared depressed, probably through volatilisation and possibly through salting-out. The selected analytical system (using a Carboxen/PDMS fiber) proved both rapid and highly sensitive (with a detection limit of 6 ng/l). During method development, salinity was shown to have a major influence in controlling the extraction efficiency and it was found necessary to adjust salinity in all samples (to 75% saturation) prior to extraction. From these tests, we (for the first time) estimated the Setschenow ("salting-out") constant of MTBE to be 0.11 l/mol.     

Comparative and combined toxicities of toluene and methyl tert-butyl ether to an Asian earthworm Perionyx excavatus

An earthworm assay was used to assess the toxicity of two main gasoline components. Ecotoxicities of toluene and methyl tert-butyl ether (MTBE) were compared for Asian earthworm Perionyx excavatus separately and in combination. Sum of toxic unit (TU) at 50% mortality for the mixture (LC50mix) was estimated from the dose (TU-based)-response relationships by the Trimmed Spearman-Karber method. Toluene was shown to be about five and two times more toxic to P. excavatus than MTBE in filter paper contact test and natural soil tests, respectively. This is primarily due to the adsorption of toluene to soil particles, leading to less bioavailability of toluene to the earthworm in soil. The combined effect of toluene and MTBE was investigated using toxic unit model, and it was found to be almost additive and synergistic responses to P. excavatus in filter paper contact test and soil tests, respectively. The combined effect of toluene and MTBE in filter paper contact test was not consistent with the results in soil toxicity tests. This phenomenon may be associated with the interaction of soil salts with pollutants. Treatment with toluene and MTBE also affected the behavior and morphology of P. excavatus. It indicates that the VOCs induce metabolic and functional damages in earthworms. Combined effects of gasoline components should be taken into account to soil risk assessment.     

Electrocatalytic oxidation of methyl tert-butyl ether (MTBE) in aqueous solution at a nickel electrode

This study utilized the electrocatalytic characteristics of nickel electrode to perform degradation of methyl tert-butyl ether (MTBE) in aqueous solution. Lab experiments were conducted in a spiltless bath type cell equipped with a nickel electrode as working electrode, a platinum wire as counter electrode, and an Ag/AgCl electrode as reference electrode. Effects of controlled potential, supporting electrolyte, and solution pH on the efficiency of MTBE removal were examined under the control of the constant-potential conditions. Experiment results showed that the optimum electrolytic condition was operated at 0.35 V in a 1M KOH electrolyte solution, and the initial 20 mgl(-1) MTBE was reduced by 73% within 180 min under the optimum control. As using 1M Na2SO4 and 1M KCl as electrolyte, the efficiency of MTBE removal dropped to 60% and 50% under the similar controls. Comparing with various pH controls, the strong basic condition is favorable for electrocatalytic oxidation of MTBE in the Ni-electrolytic system. The efficiency of MTBE removal showed a rising trend with increasing initial pH of the solution. The formation of a redox NiOOH/Ni(OH)2 layer on the anode surface, which was observed on the SEM image, can explain that nickel plays a mediator role on improving electrocatalytic oxidation of MTBE at 0.35 V in a strong basic condition. The by-products of MTBE degradation were identified as acetone and CO(2) by GC/MS, and the distributions of carbon atoms in acetone, CO2, and MTBE were found 22%, 51%, and 27% through the optimum control of electrochemical oxidation.     

Effect of chlorides and sulfates on the performance of a Fe3+/H2O2 Fenton-like system in the degradation of methyl tert-butyl ether and its byproducts.

The effect of chloride and sulfate ions on the oxidation of methyl tert-butyl ether (MTBE) and its degradation products in a Fenton-like system was studied. Although both chloride and sulfate ions inhibited the decomposition of H202, chlorides were found to be the more effective inhibitor of MTBE degradation. In the presence of sulfates, MTBE decomposition can be attributed to oxidation not only by hydroxyl radicals, but also likely by SO4*- species. In the presence of chloride ions, it is possible that the dichloride radical is formed, which is less reactive than OH*. In the system under investigation, t-butyl alcohol was found to be the major byproduct, followed by t-butyl formate and acetone. The degradation rates of all intermediates and their inhibition in the presence of inorganic ions are similar to those obtained for MTBE, although their distributions are related to the concentrations of inorganic salts added.     

好氧微生物降解林丹过程中碳-氯二维稳定同位素的分馏特性

六氯环己烷 (HCH) 是一种持久性污染物,环境存量较大时会造成污染,定量研究其在环境中的迁移转化过程具有重要意义。研究了3种好氧微生物Sphingobium quisquiliarum P25、Sphingobium ummariense RL-3和Sphingobium sp. F2降解γ-HCH (林丹) 的过程,应用单体稳定同位素分析技术 (CSIA) 探究了不同微生物对HCH的降解效果,及其对HCH转化与迁移行为的影响。结果表明：1) 3种微生物降解γ-HCH的过程符合一级反应动力学原理;2) 降解过程中碳分馏系数 (ε_C) 分别为−(4.3±0.4)‰,−(1.6±0.1) ‰和−(5.7±0.5) ‰,氯同位素分馏系数 (ε_Cl) 分别为−(1.1±0.6) ‰,−(1.5±0.2) ‰和−(1.5±0.4)‰;3) 二维同位素分馏系数 (Λ_C-Cl) 分别为(3.0±0.3),(1.1±0.1)和(2.7±0.2)。本研究结果可为应用单体稳定同位素分析技术解析复杂环境中HCH的迁移转化过程并评估HCH污染场地修复效果提供参考。     

Combined application of conservative transport modelling and compound-specific carbon isotope analyses to assess in situ attenuation of benzene, toluene, and o-xylene

In recent years, compound specific isotope analyses (CSIA) have developed into one of the most powerful tools for the quantification of in situ biodegradation of organic contaminants. In this approach, the calculation of the extent of biodegradation of organic contaminants in aquifers is usually based on the Rayleigh equation, and thus neglects physical transport processes such as dispersion that contribute to contaminant dilution in aquifers. Here we combine compound specific isotope analyses with a conservative transport model to study the attenuation of aromatic hydrocarbons at a former gasworks site. The conservative transport model was first used to simulate concentration reductions caused by dilution at wells downgradient of a BTEX source. In a second step, the diluted concentrations, together with the available stable carbon isotope ratios and carbon fractionation factors for benzene, toluene and o-xylene were applied in the Rayleigh equation to quantify the degree of biodegradation at each of those wells. At the investigated site, where other attenuation processes such as sorption and volatilisation were proven to be negligible, the combined approach is recommended for benzene, which represents a compound for which the effect of biodegradation is comparable to or less than the effect of dilution. As demonstrated for toluene and o-xylene, the application of the Rayleigh equation alone is sufficient if dilution can be proved to be insignificant in comparison to biodegradation. The analysis also suggests that the source width and the position of the observation wells relative to the plume center line are significantly related to the degree of dilution.     

Persistence of methyl <Emphasis Type="Italic">tertiary</Emphasis> butyl ether (MTBE) against metabolism by Danish vegetation

BACKGROUND: Methyl tertiary butyl ether (MTBE) is the second most highly produced industrial chemical in the US and a frequent groundwater pollutant. At the same time, MTBE is quite persistent to biotic and abiotic decomposition. The goal of this study was to find plant species that could degrade MTBE and might be used in phytoremediation. METHODS: Excised roots and leaves (0.3 g) from more than 24 Danish plant species out of 15 families were kept in glass vessels with 25 ml spiked aqueous solution for 2 to 4 days. MTBE concentrations were 1 to 5 mg/L. Samples were taken directly from the solution with a needle and injected to a purge and trap unit. MTBE and the main metabolite, TBA, were measured by GC/FID. RESULTS AND DISCUSSION: Solutions with roots of poplar (Populus robusta) and a willow hybrid (Salix viminalis x schwerinii) produced TBA in trace amounts, probably stemming from bacteria. Significant MTBE reduction (> 10%) was not observed in any of the tests. Leaves from none of the species (trees, grasses and herbs) reduced the concentration of MTBE in the solution and no TBA, nor any other known metabolite of MTBE, was detected. CONCLUSION: It was not possible to find plants capable of efficiently degrading MTBE. This gives rise to the conclusion that plants probably cannot degrade MTBE at all, or only very slowly. RECOMMENDATIONS AND OUTLOOK: For phytoremediation projects, this has, as consequence, that the volatilization by plants (except with genetically engineered plants) is the only relevant removal process for MTBE. For risk assessment of MTBE, degradation by the plant empire is not a relevant sink process.