Biodegradable Soy-Based Plastics: Opportunities and Challenges

Today's plastics are designed with little consideration for their ultimate disposability or the effect of the resources (feedstocks) used in making them. This has resulted in mounting worldwide concerns over the environmental consequences of such materials when they enter the mainstream after their intended uses. This led to the concept of designing and engineering new biodegradable materials–materials that have the performance characteristics of today's materials but that undergo biodegradation along with other organic waste to soil humic materials. Hence, the production of biodegradable materials from annually renewable agricultural feedstocks has attracted attention in recent years. Agricultural materials such as starches and proteins are biodegradable and environmentally friendly. Soybean is a good candidate for manufacturing a large number of chemicals, including biodegradable plastics, as it is abundantly available and cheap. Soy protein concentrate, isolate, or flakes could be compounded with synthetic biodegradable plastics such as polycaprolactone or poly (lactic acid) to make molded products or edible films or shopping bags and make the environment cleaner and greener.     

Thermal and Mechanical Properties of Plastics Molded from Sodium Dodecyl Sulfate-Modified Soy Protein Isolates

Soybean protein is a potential material for manufacturing of biodegradable plastics. The objective of this investigation was to characterize the thermal and mechanical properties of plastics made from sodium dodecyl sulfate (SDS)-modified soy proteins. Soy protein isolate (SPI) was prepared from defatted soy flour, modified with various concentrations of SDS, and then molded into plastics. The temperatures of denaturation of the modified soy protein increased at low SDS concentration and then decreased at high SDS concentration. At the same SDS concentration, the plastics molded from the modified soy proteins showed a similar temperature of denaturation, but a lower enthalpy of denaturation compared to the modified soy protein. Young's modulus of the plastics decreased as SDS concentration increased, and the tensile strength and strain at break of the plastics reached a maximum value at 1% SDS modification. Two glass transition temperatures were identified corresponding to the 7S and 11S globulins in SPI by dynamic mechanical analysis, and they decreased as SDS concentration increased. The SDS modification increased the water absorption of the plastics.     

Bioabsorbable soy protein plastic composites: Effect of polyphosphate fillers on water absorption and mechanical properties

The use of synthetic and natural bioabsorbable plastics has been severely limited due to their low stiffness and strength properties as well as their strong tendency to absorb moisture. This research focused on the development of bioabsorbable polyphosphate filler/soy protein plastic composites with enhanced stiffness, strength, and water resistance. Bioabsorbable polyphosphate fillers, biodegradable soy protein isolate, plasticizer, and adhesion promoter were homogenized and compression-molded. Physical, mechanical, and water absorption testing was performed on the molded specimens. Results showed improvements in stiffness, strength, and water resistance with increasing polyphosphate filler content up to 20% by weight. Application of a coupling agent produced further mechanical property enhancements and a dramatic improvement in water resistance, interpreted by an interfacial chemical bonding model. Examination of the fracture surfaces of the materials revealed that the addition of the polyphosphate fillers changed the failure mode from brittle to pseudo-ductile. These results suggest that these materials are suitable for many load-bearing applications in both humid and dry environments where current soy protein plastics are not usable.     

Processing and Characterization of Glycerol-Plasticized Soy Protein Plastics Reinforced with Citric Acid-Modified Starch Nanoparticles

Citric acid-modified starch nanoparticles with an average size of 82 nm were prepared through precipitation from gelatinized starch solution by ethanol and further modification with citric acid. When being incorporated in glycerol-plasticized soy protein plastics, citric acid-modified starch nanoparticles displayed dramatic reinforcing effect. The resulted nanocomposite plastics exhibited improvement in mechanical performance. Also, the water uptake decreased, indicating an increase of water resistance. The modified starch nanoparticles had a good compatibility with soy protein matrix. Possessing a relative hydrophobic surface, the filler would prefer to interact with protein-rich domains in glycerol-plasticized soy protein. The work provided a green approach of biodegradable materials based on naturally occurring biopolymers.     

Study on chlorine removal from mixture of waste plastics

The recycling of waste plastics that include plastics that contain chlorine, such as polyvinyl chloride, is difficult because the chlorine leads to the corrosion of equipment. Then, the dechlorination method of waste plastics containing chlorine (CCWP) that consists of a series of melt process and hot water process was examined. CCWP was put into the melt process with coal tar (HOB) and converter dust (CD) to inhibit the diffusion of the chlorine-containing gas. The results indicated that iron oxide of the principal element of CD combines with chlorine eliminated from CCWP, and forms water-soluble iron chloride on the melt process. HOB dissolves or adsorbs a part of the chlorine during the melt process, and inhibits the diffusion of the chlorine-containing gas. Approximately 98% of the chlorine in the CCWP reacts with CD and forms iron chloride, which can be extracted on the hot water process.     

The Effect of Aqueous Urea on the Processing, Structure and Properties of CGM

Corn gluten meal (CGM) is potentially a cost-effective raw material for producing a bioderivable thermoplastic. However, CGM disintegrates to a powder subsequent to processing with polar plasticisers, such as water. The hypothesis of this study was that aqueous urea could be used to denature protein within CGM and therefore encourage protein?Cprotein interactions leading to consolidated bioplastics when using water as a plasticiser. To assess this, the effects of aqueous urea on structure and properties of CGM with particular focus on storage were assessed. Processing of CGM with aqueous urea produced consolidated materials. FTIR analysis showed secondary structure was modified during processing, leading to increased amounts of ??-helices and random coils and reduction of the amount of intermolecular ??-sheets and turns. Above 6?wt% free water, the plasticising efficiency of water in processed CGM increased as the amount of denatured proteins increased. Below 6?wt% free water, protein secondary structure did not have a significant influence on thermal and flexural properties. It was found that storage environment and urea concentration influenced the rate of drying, however, the final water content was constant relative to CGM, and not urea. The materials were resistant to cracking at urea concentrations above 8?M, provided the mass loss during storage did not exceed 15?wt%.     

Sustainable Bio-Composites from Renewable Resources: Opportunities and Challenges in the Green Materials World

Sustainability, industrial ecology, eco-efficiency, and green chemistry are guiding the development of the next generation of materials, products, and processes. Biodegradable plastics and bio-based polymer products based on annually renewable agricultural and biomass feedstock can form the basis for a portfolio of sustainable, eco-efficient products that can compete and capture markets currently dominated by products based exclusively on petroleum feedstock. Natural/Biofiber composites (Bio-Composites) are emerging as a viable alternative to glass fiber reinforced composites especially in automotive and building product applications. The combination of biofibers such as kenaf, hemp, flax, jute, henequen, pineapple leaf fiber, and sisal with polymer matrices from both nonrenewable and renewable resources to produce composite materials that are competitive with synthetic composites requires special attention, i.e., biofiber–matrix interface and novel processing. Natural fiber–reinforced polypropylene composites have attained commercial attraction in automotive industries. Natural fiber—polypropylene or natural fiber—polyester composites are not sufficiently eco-friendly because of the petroleum-based source and the nonbiodegradable nature of the polymer matrix. Using natural fibers with polymers based on renewable resources will allow many environmental issues to be solved. By embedding biofibers with renewable resource–based biopolymers such as cellulosic plastics; polylactides; starch plastics; polyhydroxyalkanoates (bacterial polyesters); and soy-based plastics, the so-called green bio-composites are continuously being developed.     

Improved method for the formation of recycled resins from depolymerized products of waste fiber-reinforced plastics: simple and effective purification of recovered monomers by washing with water

The synthesis of recycled plastics from recovered monomeric materials obtained from the depolymerization reaction of fiber-reinforced plastics (FRP) was examined. The depolymerization reaction of FRP in the presence of N,N-dimethylaminopyridine (DMAP) smoothly yielded the corresponding monomers, which mainly consisted of dimethyl phthalates. The polymerization reaction with this monomer failed to form the corresponding unsaturated polyesters due to contamination by N-methyl-4-pyridone, a decomposition product of DMAP. An efficient purification of the recovered monomer was achieved by washing with water, and the purified monomer successfully yielded the corresponding polymers. A hardness test revealed that the polymers were as hard as the polyester made from virgin materials. The present modification provides a practical method for the preparation of recycled plastics from depolymerized plastics.     

Processing and Physical Properties of Plastics Made from Soy Protein Polyester Blends

Blending soy protein with polyesters using a polyvinyllactam as a compatibilizer successfully made soy protein-based plastics. The polyesters used to produce blends included polycaprolactone (PCL) and Biomax (a commercial biodegradable polyester). The blends were processed by compounding extrusion and injection molding. Blends containing soy protein/Biomax-poly(vinyl alcohol) had tensile strengths ranging from 16–22 MPa, with samples containing larger percentages of the synthetic polymer exhibiting greater strengths. Blends made from soy protein, Biomax, and PCL had tensile strengths ranging from 27–33 MPa. All the blends had high Young's moduli but demonstrated brittle characteristics as evident from their low elongations at break, ranging from 1.8–3.1%. Plastics made from soy protein/polyester blends exhibited low water absorption and had good stability under ambient conditions relative to the plastics made from soy protein alone. Blends made from soy protein flour produced plastics with the lowest water absorption.     

Effects of Storage Time on Properties of Soybean Protein-Based Plastics

Soybean protein has been considered as a potential biodegradable polymer in the manufacture of plastics. The purpose of this investigation was to characterize the effect of storage time on thermal and mechanical properties of soybean protein isolate (SPI) plastics. SPI was separated from defatted soy flour, modified with 1M or 2M urea, or plasticized with glycerol, and compression molded into plastics. Plastic made from SPI alone was used as a control. For all SPI plastics, glass transition temperatures and dynamic storage modulus increased and loss tangent decreased during storage. Excess enthalpy of relaxation of all SPI plastics had an exponential relationship with storage time, indicating a fast aging rate at the beginning of storage. All SPI plastics tended to be stiff and brittle during storage. The plastics with glycerol had the slowest aging rate and were fairly stable after 60 days, with about 8.8 MPa tensile strength and 168% strain at break. Plastics with the 2M urea-modification SPI also had a slow aging rate and became relative stable after 60 days, with about 10 MPa tensile strength and 72% elongation.     

Identification and thermomechanical characterization of polymers recovered from mobile phone waste

The plastic components from waste mobile phones were sorted and characterized using visual, spectroscopic and thermal methods. The sustainable strength of the recovered plastics was investigated by comparing their mechanical and thermal properties with commercially used reference materials. The results revealed that the recovered polymers have significant potential to be reused. However, some properties, such as impact strength and tensile modulus, are significantly low compared to virgin materials and need further improvement. The samples were also tested for brominated flame retardants (BFRs) using gas chromatography–mass spectrometry technique, and the results indicated the absence of BFR in recovered plastics; hence, these can be processed without any risk of BFR toxicity.     

Application of a gas-solid fluidized bed separator for shredded municipal bulky solid waste separation

A laboratory-scale gas-solid fluidized bed separator able to separate fractions of 5.6-50mm was used for separation of shredded municipal bulky waste (SBW) into combustibles and incombustibles. In batch-scale tests, it was found that accumulation of SBW in the bottom of the bed significantly reduced the separation efficiency. In this study, stirring was shown to be effective in preventing this accumulation. Flexible sheet materials such as paper and film plastics also significantly decreased the separation efficiency. In batch-scale tests, an overall efficiency of 90% was obtained when flexible materials such as film plastics and paper were excluded from the feed SBW. In continuous feeding tests, purities of the float and sink fractions attained 95% and 86% efficiencies, respectively, with an overall efficiency of 79%. The effect of feedstock shape on separation efficiency was also investigated. This study revealed that large particles can be properly separated on the basis of density, while the shape of the material significantly influenced behavior in the fluidizing bed.     

Bio-Based Polymers and End-of-Life Vehicles

As new materials, such as bio-based plastics and composites, are introduced in vehicles for their improved environmental performance, it is necessary to understand how to efficiently recover these biodegradable materials. This paper provides an overview of the end-of-life phase for automobiles, focusing on the dismantling and shredding processes, and the recovery of materials. Targeted unit operations, such as dismantling of components from vehicles and pretreatment prior to shredding, along with design-for-environment principles, should enable the efficient recovery of materials at the end-of-life phase compared with popularly conceived all-in-one-approaches because of the diverse arrangement of material components.     

Synthesis of3H- polyethylene and its use for fate studies on degradable plastics

Determining the fate of xenobiotic materials in the environment can be aided by the use of radioactive isotope technology. Previous research on the degradation of polymers such as polyethylene (PE) was aided by the utilization of radiotracers. In order to study the environmental fate of degradable (PE/starch) plastics, we synthesized³H-labeled PE. Results of soil incubation studies indicate that only minimal degradation of the PE component, as indicated by the production of water-soluble metabolites, occurred during 2 years of incubation in soil. Despite the minimal degradation, the³H label did not allow for detection of the degradation products. In addition, the³H-PE was particularly useful for tracing the fate of degradable plastics after consumption by terrestrial isopods. The detection of aqueous-soluble radioactivity in isopod frass was used to indicate degradation of the plastic film.     

Thermoplastic Blends from Albumin and Zein: Plastic Formation and Mechanical Properties Including Modeling

The use of proteins in blending with traditional polymers in the formation of thermoplastics can produce plastics with properties that are superior to traditional petroleum-based plastics. We investigated the physical and thermal properties of albumin and zein thermoplastic blends plasticized with glycerol and mixed with varying amounts of low-density polyethylene (LDPE). Several mechanical models were utilized to determine how tensile properties will be altered when varying amounts of protein/LDPE were added into the thermoplastic blend. When analyzed for thermal properties, we found that as the amount of LDPE in the thermoplastic blend increased, the resulting plastic possessed thermal properties that were more similar to pure LDPE plastics. In terms of mechanical properties, comparison between the experimental data and model predictions points to a synergistic effect between albumin and LDPE that leads to higher modulus, while a potential lack of compatibility between zein and LDPE leads to a plastic with lower modulus. Based on our results, the use of albumin and zein proteins when blended with LDPE in the production of thermoplastics has potential use in the areas of medical and food packaging applications.     

Modification of Soy Protein Plastic with Functional Monomer with Reactive Extrusion

Chemical modification of soy protein with monomers such as maleic anhydride, glycidyl methacrylate and styrene was accomplished using reactive extrusion technology. Thermal and mechanical properties of the modified soy protein plastics were characterized with differential scanning calorimetry (DSC), a dynamic mechanical analyzer (DMA) and a United Testing System load frame. It was found that the denaturation temperature and the glass transition temperature of soy protein plastic changed. In addition, the tensile properties of modified soy protein plastic improved. Attenuated total reflection Fourier transform infrared (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS) were used to characterize the structure of modified soy proteins. A suggestion of the interaction between soy protein and functional group in functional polymers is given. Through the in-situ interaction between the polymer and soy protein plastic, the mechanical properties of the soy protein plastic can be adjusted and controlled.     

Mechanical, Thermal and Water Absorption Properties of Kenaf-Fiber-Based Polypropylene and Poly(Butylene Succinate) Composites

The use of composites made from non-biodegradable conventional plastic materials (e.g., polypropylene, PP) is creating global environmental concern. Biodegradable plastics such as poly(butylene succinate) (PBS) are sought after to reduce plastic waste accumulation. Unfortunately, these types of plastics are very costly; therefore, natural lignocellulosic fibers are incorporated to reduce the cost. Kenaf fibers are also incorporated into PP and PBS for reinforcing purposes and they have low densities, high specific properties and renewable sourcing. However without good compatibilization, the interfacial adhesion between the matrix and the fibers is poor due to differences in polarity between the two materials. Maleic anhydride-grafted compatibilizers may be introduced into the system to improve the matrix-fiber interactions. The overall mechanical, thermal and water absorption properties of PP and PBS composites prepared with 30 vol.% short kenaf fibers (KFs) using a twin-screw extruder were being investigated in this study. The flexural properties for both types of composites were enhanced by the addition of compatibilizer, with improvements of 56 and 16 % in flexural strength for the PP/KF and PBS/KF composites, respectively. Good matrix-fiber adhesion was also observed by scanning electron microscopy. However, the thermal stability of the PBS/KF composites was lower than that of the PP/KF composites. This result was confirmed by both DSC and TGA thermal analysis tests. The water absorption at equilibrium of a PBS composite filled with KFs is inherently lower than of a PP/KF composite because the water molecules more readily penetrate the PP composites through existing voids between the fibers and the matrix. Based on this research, it can be concluded that PBS/KF composites are good candidates for replacing PP/KF composites in applications whereby biodegradability is essential and no extreme thermal and moisture exposures are required.     

Carbon materials-catalyzed hydroliquefaction of flame-retardant plastics in organic solvents

Flame-retardant plastics, such as desktop and laptop personal computer bodies, could be completely liquefied by carbon materials-catalyzed hydroliquefaction in tetralin without using H₂ as a hydrogen source. Active carbons with larger surface areas (1450–3450 m²/g) acted as superior catalysts in transferring tetralin hydrogens to plastics. On the other hand, carbon blacks and fullerene-rich soot were less active catalysts. Graphite and mesocarbon microbeads did not show any catalytic effects. Benzene, toluene, and ethylbenzene were obtained as recyclable hydrocarbons; their total amounts varied from 4 wt% to 12 wt% depending on the types of plastics and the carbon materials used. Organic bromides such as polybromodioxins were not contained in the gases and oils of the product. Received: July 19, 2000 / Accepted: September 17, 2000     

Production and degradation of polyhydroxyalkanoates in waste environment

Polyhydroxyalkanoates (PHAs) are energy/carbon storage materials accumulated under unfavorable growth condition in the presence of excess carbon source. PHAs are attracting much attention as substitute for non-degradable petrochemically derived plastics because of their similar material properties to conventional plastics and complete biodegradability under natural environment upon disposal. In this paper, PHA production and degradation in waste environment as well as its role in biological phosphorus removal are reviewed. In biological phosphorus removal process, bacteria accumulating polyphosphate (poly P) uptake carbon substrates and accumulate these as PHA by utilizing energy from breaking down poly P under anaerobic condition. In the following aerobic condition, accumulated PHA is utilized for energy generation and for the regeneration of poly P. PHA production from waste has been investigated in order to utilize abundant organic compounds in waste water. Since PHA content and PHA productivity that can be obtained are rather low, PHA production from waste product should be considered as a coupled process for reducing the amount of organic waste. PHAs can be rapidly degraded to completion in municipal anaerobic sludge by various microorganisms. ©     

工业贮池防腐材料及其施工性能

总结了常用的工业贮池防腐蚀处理方法、防腐蚀材料的性能及施工过程和要点,比较了玻璃钢衬里、玻璃鳞片与乙烯基酯树脂混合衬里和耐酸块材砌筑等防腐蚀处理工艺的工艺条件,并介绍了玻璃钢衬里工艺中所用树脂的类型及性能.