Validation of a standardized portable fluorescence method for determining trace beryllium in workplace air and wipe samples

Beryllium is widely used in industry for its unique properties; however, occupational exposure to beryllium particles can cause potentially fatal disease. Consequently, exposure limits for beryllium particles in air and action levels on surfaces have been established to reduce exposure risks for workers. Field-portable monitoring methods for beryllium are desired in order to facilitate on-site measurement of beryllium in the workplace, so that immediate action can be taken to protect human health. In this work, a standardized, portable fluorescence method for the determination of trace beryllium in workplace samples, i.e., air filters and dust wipes, was validated through intra- and inter-laboratory testing. The procedure entails extraction of beryllium in 1% ammonium bifluoride (NH(4)HF(2), aqueous), followed by fluorescence measurement of the complex formed between beryllium ion and hydroxybenzoquinoline sulfonate (HBQS). The method detection limit was estimated to be less than 0.02 microg Be per air filter or wipe sample, with a dynamic range up to greater than 10 microg. The overall method accuracy was shown to satisfy the accuracy criterion (A< or = +/-25%) for analytical methods promulgated by the US National Institute for Occupational Safety and Health (NIOSH). Interferences from numerous metals tested (in >400-fold excess concentration compared to that of beryllium) were negligible or minimal. The procedure was shown to be effective for the dissolution and quantitative detection of beryllium extracted from refractory beryllium oxide particles. An American Society for Testing and Materials (ASTM) International voluntary consensus standard based on the methodology has recently been published.     

Development of an extraction method for perchlorate in soils

Perchlorate originates as a contaminant in the environment from its use in solid rocket fuels and munitions. The current US EPA methods for perchlorate determination via ion chromatography using conductivity detection do not include recommendations for the extraction of perchlorate from soil. This study evaluated and identified appropriate conditions for the extraction of perchlorate from clay loam, loamy sand, and sandy soils. Based on the results of this evaluation, soils should be extracted in a dry, ground (mortar and pestle) state with Milli-Q water in a 1 ratio 1 soil ratio water ratio and diluted no more than 5-fold before analysis. When sandy soils were extracted in this manner, the calculated method detection limit was 3.5 microg kg(-1). The findings of this study have aided in the establishment of a standardized extraction method for perchlorate in soil.     

Interlaboratory evaluation of trace element determination in workplace air filter samples by inductively coupled plasma mass spectrometry

Inductively coupled plasma mass spectrometry (ICP-MS) is becoming more widely used for trace elemental analysis in the occupational hygiene field, and consequently new ICP-MS international standard procedures have been promulgated by ASTM International and ISO. However, there is a dearth of interlaboratory performance data for this analytical methodology. In an effort to fill this data void, an interlaboratory evaluation of ICP-MS for determining trace elements in workplace air samples was conducted, towards fulfillment of method validation requirements for international voluntary consensus standard test methods. The study was performed in accordance with applicable statistical procedures for investigating interlaboratory precision. The evaluation was carried out using certified 37-mm diameter mixed-cellulose ester (MCE) filters that were fortified with 21 elements of concern in occupational hygiene. Elements were spiked at levels ranging from 0.025 to 10 μg filter(-1), with three different filter loadings denoted "Low", "Medium" and "High". Participating laboratories were recruited from a pool of over fifty invitees; ultimately twenty laboratories from Europe, North America and Asia submitted results. Triplicates of each certified filter with elemental contents at three different levels, plus media blanks spiked with reagent, were conveyed to each volunteer laboratory. Each participant was also provided a copy of the test method which each participant was asked to follow; spiking levels were unknown to the participants. The laboratories were requested to prepare the filters by one of three sample preparation procedures, i.e., hotplate digestion, microwave digestion or hot block extraction, which were described in the test method. Participants were then asked to analyze aliquots of the prepared samples by ICP-MS, and to report their data in units of μg filter(-1). Most interlaboratory precision estimates were acceptable for medium- and high-level spikes (RSD <25%), but generally yielded greater uncertainties than were anticipated at the outset of the study.     

Investigation of trace elements in agricultural soils by BCR sequential extraction method and its transfer to wheat plants

In this study, soil samples were collected from Edirne, Turkey in both summer and winter seasons and subjected to the modified Community Bureau of Reference (BCR) sequential extraction procedure in order to investigate the chemical partitioning of metals in soils and to predict heavy metals uptake by wheat grains which grown at the same soils. The samples were subjected to a three stage extraction procedure proposed by the BCR. The three phases that were separated out in the following order: (1) carbonate, exchangeable, (2) Fe?CMn oxides, and (3) organic matter. Metal concentrations of soil fractions and grain samples were determined by inductively coupled plasma atomic emission spectroscopy. The wheat samples were prepared to analysis using microwave acid digestion procedure. The pseudo-total concentrations of metals were determined after aqua regia digestion. The analytical accuracy of the method was evaluated by using the Standard Reference Materials (BCR 142R Light Sandy Soil, NIST 2711 Montana Soil, and NIST 2704 Buffalo River Sediment). The sum of the metal contents obtained from the modified BCR sequential extraction procedure and pseudo-total metal contents for soil samples were used to calculate recovery values. In order to evaluate the bioavailability of metals, the relationships between the wheat-metal and soil-extractable metal concentrations were compared.     

Flow-injection analysis with fluorescence detection for the determination of trace levels of ammonium in seawater

A method using flow-injection, gas-diffusion, derivatisation and then fluorescent detection has been established for ammonium ion determination in seawater. The fluorescent derivative formed by reacting ortho-phthaldialdehyde (OPA) and sulfite with ammonia gives high sensitivity while removing potential interferences. This is required to measure the low concentrations of ammonium often seen in the open ocean. The experimental conditions (flow-rate, reagent concentrations, membrane configurations, etc.) were manipulated to improve performance. For a sample throughput of 30 samples h(-1), the limit of detection was 7 nM, the coefficient of variation was 5.7% at 800 nM, and the calibration curve was linear to at least 4 micromol L(-1). Interferences were minimised by a gaseous diffusion step. Volatile small molecular-weight amines as interferents were discriminated against by this method. They neither passed through the membrane as efficiently as ammonia, nor reacted as readily with OPA when sulfite was the reductant. Contamination by ammonia from laboratory and shipboard sources complicates application of the method to natural waters, especially measurement of low concentrations (<100 nM) in open-ocean waters. Steps to overcome contamination are described in detail. Some results are presented for ammonium determination in Southern Ocean and Huon Estuary (Tasmania) waters.     

Optimization of a multielement sequential extraction method employing an experimental design approach for metal partitioning in soils and sediments

The optimisation of a simple multielement extraction method employing an experimental design approach is described. The method uses centrifugation to pass one extractant solution at varying pH through a contaminated soil sample. The nature and concentration of the acid, rate of centrifugation and time, number of sequential leachates and the ratio of extractant volume: sample weight have been studied in order to obtain the optimum conditions for extraction. A fractional factorial experimental design was performed, and the results were used to identify significance which was then evaluated by carrying out a central composite experimental approach. Once optimum conditions had been obtained, sequential leaches were analysed by ICP-AES and chemometrics were employed to identify the composition of each component. Comparisons have been made with previous studies and tentative assignments, based on well defined separated fractions and percentage compositions for individual elements, used to identify the different physico-chemical components in the sample.     

铬菁R分光光度法测定水和废水中痕量铍的方法评价

在方法研究的基础上 ,组织全国六个实验室对铬菁 R分光光度法测定水和废水中铍进行了方法验证。对统一标准样品、环境地表水、实际含铍废水进行了分析。以协作试验所得数据评价本方法的灵敏度、精密度、准确度和适用性     

Selection and evaluation of sequential extraction procedures for the determination of phosphorus forms in lake sediment

In order to achieve comparable measurements in the determination of phosphate forms in freshwater sediments, the Standards, Measurements and Testing Programme (formerly BCR) of the European Commission has launched a project the first step of which was to select and evaluate collaboratively existing extraction procedures. This was carried out through expert consultations and a literature survey, and was followed by the organisation of a first interlaboratory study for the evaluation of four sequential extraction schemes, one of which was selected as the most promising method for achieving comparability. This scheme, a modified version of the Williams protocol, was further tested in a second interlaboratory study. The so-called SMT extraction scheme seems promising and will provide, in the near future, a valuable tool for water managers in the field of lake restoration. It will be particularly helpful in estimating the stock of P potentially available, hence the risk of eutrophication due to internal P release.     

A combination of micro-porous membrane liquid-gas extraction and solid-phase trapping for ultra trace determination of benzene in urine

A method was developed for the determination of benzene in urine. The sample was pumped through the donor channel of a membrane extraction unit with a micro-porous membrane, separating the donor channel from an identical acceptor channel purged with nitrogen. The analyte reached the acceptor channel by diffusion through the membrane and was then swept by the carrier to a solid sorbent tube, where it was trapped. The analyte was subsequently thermally desorbed and analyzed by gas chromatography (GC) with mass selective detection (MS). After optimization, the recovery was close to quantitative, or 95%. Purging the membrane unit with pure water in between the samples eliminated any memory effects. The linearity was good in the concentration range examined (20-4000 ng l(-1)), with a correlation coefficient of 0.9996. The repeatability at 50 ng l(-1) and 400 ng l(-1) was 1.4% and 1.2%, respectively. The limit of detection was 12 ng l(-1) and the limit of quantification 35 ng l(-1). This enables assessment of benzene exposures of occupationally exposed subjects, of smokers and the majority of the general population. The developed method can be easily automated.     

Interlaboratory comparability of copper complexation capacity determination in natural waters

The results of a test of interlaboratory comparability for the determination of copper complexation capacity and copper-ligand complex formation constant are presented. Eight water samples comprising, six natural waters, a synthetic ligand solution and a blank solution were analysed by seven laboratories using their own methods of complexation titration. Given the wide variation that might have been possible, relatively good comparability was demonstrated amongst the variety of methods for determining copper complexation capacity. The complexation capacity data largely satisfied the predefined criterion of agreement to within 50%. This provides support for the use of metal speciation criteria in the regulation of copper in the environment. Data for the determination of complex formation constants were of poorer comparability, ranging between 10(7) and 10(12) for the same water.     

砷钼杂多酸─罗丹明6G荧光猝灭法测定痕量砷

探讨了在聚乙烯醇存在下，砷钼杂多酸──罗丹明６Ｇ荧光猝灭法测定痕量砷的条件，其λ_（ｅｍ）位于５６０ｎｍ，Ａｓ（Ｖ）量在２～６０ｎｇ／ｍＬ范围内与荧光猝灭值成线性关系。方法可用于环境水样中痕量砷的测定。     

原子荧光度法测定城市污泥总砷的不确定度评定

根据《测量不确定度评定与表示》（JJF1059—1999）,建立了原子荧光度法测定污泥泥质中砷不确定度的数学模型,分析了测试过程中不确定度的来源,并对各不确定度分量进行评定及合成,并计算得出合成不确定度和扩展不确定度。本次测量的合成相对不确定度值为0．023,其中由消化样浓度引起的相对合成不确定度为0．021;最大的不确定度分量是样品消化重复测定的不确定度,分量值为O．0152。本次测定结果为19．97±0．92mg／kg,k=2（置信水平约为95％）。     

Interlaboratory trial to determine the analytical state-of-the-art of bromate determination in drinking water

The new European Directive for water intended for human consumption has established a regulatory level for bromate at 10 microg L(-1). This Maximum Admissible Concentration requires analytical methods with detection limits of a least 2.5 microg L(-1). A project funded by the Standards, Measurements and Testing Programme of the European Commission has enabled the improvement and/or development of methods for the determination of bromate at such concentration levels. This collaborative work was concluded by the organisation of an interlaboratory trial involving 26 European laboratories, which enabled the testing of both a draft ISO Standard method and alternative methods. This paper presents the results of this interlaboratory trial, along with results of a bromate stability study. The progress made with respect to the analytical state-of-the-art for bromate will greatly benefit the quality of measurements carried out in water quality monitoring.     

Comparison of leaching tests for the study of trace metals remobilisation in soils and sediments

Several leaching tests were applied and compared to study metal remobilisation on various unpolluted and contaminated soils and on several contaminated sediments. The trace elements considered were Cd, Cr, Cu, Ni, Pb and Zn, and leaching tests consisted of the application of reagents with contrasting characteristics and strengths in order to assess the information provided. An extraction with aqua regia permitted the estimation of the pseudo-total metal content in the sample. Mild extractants such as H2O, CaCl2 and NaNO3 showed low and similar leaching capacities. Acid (CH3COOH) and complexing (EDTA) agents were more effective in remobilising trace metals from soils and sediments. Cd and Zn showed similar extraction characteristics under both extractant solutions, whereas Cu and Pb were more sensitive to complexation, and Ni and Cr to acidification processes. Sequential chemical extractions provided additional information on the association of the trace elements with the different soil and sediment phases. Cd and Zn showed the highest mobility, Pb was associated to reducible solid phases, Cu and Ni to oxidisable phases, and Cr remained mostly in the residual fraction. The results obtained in this paper provided valuable information for choosing a leaching test, which is an instrument of environmental analysis for the estimation of trace metal mobility.     

Concentration of trace metals in sediments and soils from protected lands in south Florida: background levels and risk evaluation

A comprehensive environmental evaluation was completed on 20 metals: two reference metals (Fe, Al) and several minor trace metals (As, Ba, Co, Cr, Cu, Mn, Ni, Pb, V, and Zn) for surface soils and sediments collected from 50 sites in Everglades National Park (ENP), the coastal fringes of Biscayne National Park (BNP), and Big Cypress National Preserve. Samples were prepared by acid digestion (EPA3050) and analyzed by ICP/MS detection (EPA6020). Although no widespread contamination was detected across the two parks and one preserve, there were some specific areas where metal concentrations exceeded Florida’s ecological thresholds, suggesting that some metals were of concern. A screening-level evaluation based on a proposed effect index grouped trace metals by their potential for causing negligible, possible, and probable effects on the biota. For example, Cu in BNP and Cr and Pb in ENP were considered of concern because their adverse effect likelihood to biota was assessed as probable; consequently, these trace metals were selected for further risk characterization. Also, stations were ranked based on a proposed overall contamination index that showed that: site BB10 in BNP and sites E3 and E5 in ENP had the highest scores. The first site was located in a marina in BNP, and the other two sites were along the eastern boundary of ENP adjacent to current or former agricultural lands. An assessment tool for south Florida protected lands was developed for evaluating impacts from on-going Everglades restoration projects and to assist State and Federal agencies with resource management. The tool consists of enrichment plots and statistically derived background concentrations based on soil/sediment data collected from the two national parks and one preserve. Finally, an equally accurate but much simplified approach is offered for developing enrichment plots for other environmental settings.     

Multi-residue determination of pharmaceuticals in sludge and sludge enriched soils using pressurized liquid extraction, solid phase extraction and liquid chromatography with tandem mass spectrometry

An analytical method to determine a selection of 27 frequently prescribed and consumed pharmaceuticals in biosolid enriched soils and digested sludges is presented. Using a combination of pressurized liquid extraction, solid phase extraction and liquid chromatography with tandem mass spectrometry, it was possible to detect all analytes in each sample type at the low-sub ng g(-1) level. Solid phase extraction efficiencies were compared for 6 different sorbent types and it was found that Waters Oasis HLB cartridges offered enhanced selectivities with 20 analytes showing final method recoveries > or =60% in both soils and digested sludges. The method was validated for linearity, range, precision and limits of detection in both sample matrices. All analytes were then determined in sludge enriched soils as well as the precursor thermally dried sludge fertilizer produced from a primary wastewater treatment plant. Levels of the antibacterial agent triclosan were found to exceed 20 microg g(-1) in digested sludge and 5 microg g(-1) in thermally dried sludge cake. Significant traces of carbamazepine and warfarin were also detected in the above samples.     

Interlaboratory evaluation of endotoxin analyses in agricultural dusts--comparison of LAL assay and mass spectrometry

Endotoxin exposure is associated with wheeze and asthma morbidity, while early life exposure may reduce risk of allergy and asthma. Unfortunately, it is difficult to compare endotoxin results from different laboratories and environments. We undertook this study to determine if lipopolysaccharide (LPS) extraction efficiency could account for differences among laboratories. We generated and collected aerosols from chicken and swine barns, and corn processing. We randomly allocated side-by-side filter samples to five laboratories for Limulus assay of endotoxin. Lyophilized aliquots of filter extracts were analyzed for 3-hydroxy fatty acids (3-OHFAs) as a marker of LPS using gas chromatography-mass spectrometry. There were significant differences in endotoxin assay and GC-MS (LPS) results between laboratories for all dust types (p < 0.01). Patterns of differences between labs varied by dust type. Relationships between assay and GC/MS results also depended on dust type. The percentages of individual 3-OHFA chain lengths varied across labs (p < 0.0001) suggesting that each lab recovered a different fraction of the LPS available. The presence of large amounts of particle associated LPS and absence of a freezing thawing cycle were associated with lower correlations between LPS and bioactivity, consistent with an absence of Limulus response to cell-bound endotoxin. These data suggest that extraction methods affect endotoxin measurements. The LAL methods may be most suitable when comparing exposures within similar environments; GC-MS offers additional information helpful in optimizing sample treatment and extraction. GC-MS may be of use when comparing across heterogeneous environments and should be considered for inclusion in future studies of human health outcomes.     

Synchrotron X-ray fluorescence and trace metals in the cementum rings of human teeth

Synchrotron micro X-ray fluorescence has been used to study differences in the trace element concentration between the dentine and cementum rings of human teeth. The results show that metals such as zinc are concentrated in the cementum rings. This suggests that if the rings are deposited annually a temporal record of metal exposure may be extracted from this material.     

Autoclave decomposition method for metals in soils and sediments

Leaching of partially leached metals (Fe, Mn, Cd, Co, Cu, Ni, Pb, and Zn) was done using autoclave technique which was modified based on EPA 3051A digestion technique. The autoclave method was developed as an alternative to the regular digestion procedure passed the safety norms for partial extraction of metals in polytetrafluoroethylene (PFA vessel) with a low constant temperature (119.5° ± 1.5°C) and the recovery of elements were also precise. The autoclave method was also validated using two Standard Reference Materials (SRMs: Loam Soil B and Loam Soil D) and the recoveries were equally superior to the traditionally established digestion methods. Application of the autoclave was samples from different natural environments (beach, mangrove, river, and city soil) to reproduce the recovery of elements during subsequent analysis.     

Comparison of a matrix solid phase dispersion and a classical extraction method for the determination of chlorinated pesticides in fish muscle

A new multiresidue extraction technique was used to determine incurred chlorinated hydrocarbon pesticide residues in various fish species sampled at 2 locations along the Tensas River in Louisiana. Residue levels of total DDT (combined DDT, DDE, and DDD levels) in fish muscle fillets from paired samples ranged from 0.2 to 3.9 ppm on a wet weight basis. These findings were compared to those of another laboratory that used a different protocol to isolate the residues from the fish muscle fillets. This latter protocol typifies the more complicated, time-consuming protocols used by governmental agencies for screening purposes. Results demonstrated that the new extraction technique reduced analysis time, solvent waste, and cost per sample without affecting the quality of residue detection and measurement.