TCLP法评价钢铁工业区周边土壤重金属生态环境风险

采用土壤随机布点法,采集某钢铁工业区周边34个土壤样品,利用美国TCLP法对钢铁工业区周边土壤重金属（Cu、 Zn、 Pb、 Cd）有效态进行实验分析和生态风险评价。结果表明, Cu、 Zn、 Pb、 Cd有效态含量分别在0.87~57.7 mg/kg、5.20~1338 mg/kg、1.09~379 mg/kg、1.15×10-3~69.9×10-3 mg/kg之间,钢铁工业区土壤不同程度地受到重金属的污染,其中以Zn污染最为严重。内梅罗污染指数评价中,处于安全水平的点位仅占17.6%,受到污染的点位占55.9%。其中,轻污染占20.6%,中污染占2.9%,重污染占32.4%。     

Dissolution of trace element contaminants from two coastal plain soils as affected by pH

Trace element mobility in soils depends on contaminant concentration, chemical speciation, water movement, and soil matrix properties such as mineralogy, pH, and redox potential. Our objective was to characterize trace element dissolution in response to acidification of soil samples from two abandoned incinerators in the North Carolina Coastal Plain. Trace element concentrations in 11 soil samples from both sites ranged from 2 to 46 mg Cu kg(-1), 3 to 105 mg Pb kg(-1), 1 to 102 mg Zn kg(-1), 3 to 11 mg Cr kg(-1), < 0.1 to 10 mg As kg(-1), and < 0.01 to 0.9 mg Cd kg(-1). Acidified CaCl2 solutions were passed through soil columns to bring the effluent solution to approximately pH 4 during a 280-h flow period. Maximum concentrations of dissolved Cu, Pb, and Zn at the lowest pH of an experiment (pH 3.8-4.1) were 0.32 mg Cu L(-1), 0.11 mg Pb L(-1), and 1.3 mg Zn L(-1) for samples from the site with well-drained soils, and 0.25 mg Cu L(-1), 1.2 mg Pb L(-1), and 1.4 mg Zn L(-1) for samples from the site with more poorly drained soils. Dissolved Cu concentration at pH 4 increased linearly with increasing soil Cu concentration, but no such relationship was found for Zn. Dissolved concentrations of other trace elements were below our analytical detection limits. Synchrotron X-ray absorption near edge structure (XANES) spectroscopy showed that Cr and As were in their less mobile Cr(III) and As(V) oxidation states. XANES analysis of Cu and Zn on selected samples indicated an association of Cu(II) with soil organic matter and Zn(II) with Al- and Fe-oxides or franklinite.     

Germination,Growth, and Nodulation of Sesbania rostrata Grown in Pb/Zn Mine Tailings

Sesbania rostrata in pure and amended Pb/Zn tailings. About 90% of seeds of S. rostrata germinated in pure Pb/Zn tailings, which contained high concentrations of Pb, Zn, Cu, and Cd. Although seedling growth suffered from the adverse environment of Pb/Zn tailings, they became established on tailings stands, in the greenhouse, as well as on the actual tailings dam, and completed their life cycle in 4 months. Dry matter production and nitrogen accumulation was 3200 kg/ha and 69.4 kg/ha, respectively in the actual tailings dam. Applying inorganic fertilizer to Pb/Zn tailings led to no obvious improvement in growth and nodulation of S. rostrata, while tailings amended by river sediment or domestic refuse rich in organic matter improved the growth and nodulation of the species. Azorhizobium caulinodans survived and formed N-fixing stem and root nodules in S. rostrata grown in pure Pb/Zn tailings with a nodule biomass exceeding 300 mg fresh matter per plant.     

湘中某工业区农田重金属污染的初步研究

通过2年的定点调查,研究了湘中某工业区附近农田土壤、糙米中重金属含量状况;并对重金属在水稻植株中的含量分布,以及影响糙米中重金属含量的土壤因素进行了探讨。     

湘江株洲段表层水重金属含量及存在形态分布研究

以国家Ⅲ类水质限值为标准,总体来讲,湘江株洲段河水中Cu、Pb、Zn和Cd的总量均不超标,Cd的污染较重。霞湾断面的污染最重,清水塘工业区铅锌冶炼和化工企业是其污染的主要来源。采用化学分析的方法,对湘江株洲段水体中的Cu、Pb、Zn和Cd进行了形态分析,Cu、Zn溶解态在各断面均大于50%;Pb、Cd的形态在不同的断面其所占比例不一样。监测了各水质参数,pH大都在7.5左右,Eh在200~300mv之间,为氧化的环境,COD大部分断面均在15~20mg/L以下。     

Concentration and chemical speciation for the determination of Cu,Zn, Ni,Pb and Cd from refuse dump soils using the optimized BCR sequential extraction procedure

The optimized BCR sequential extraction procedure (proposed by the Standards, Measurements and Testing Programme (SM&T) of the European Union) was applied to seven topsoil samples from refuse dump sites for the determination of Cu, Zn, Ni, Pb and Cd. The metals were partitioned into four operationally defined chemical fractions: acid extractable, reducible, oxidizable and residual, and analysed using flame atomic absorption spectrophotometry, FAAS. The results were compared with total metal concentrations obtained using HNO₃, HClO₄ and HF digestion procedures. Results for total metal analysis ranged from - 15.55 to 43.45 for Cu, 37.15 to 222.35 for Zn, 5.15 to 12.10 for Ni, 10.30 to 93.05 for Pb and 0.35 to 3.75 for Cd in μgg⁻¹ dry weight. The results of the partitioning study showed that zinc prevailed in the more soluble fractions and was distributed between the acid-extractable (32.4%) and the reducible (40.3%) fractions, whereas Pb was distributed mainly in the reducible fraction. Copper and nickel were predominantly associated with the reducible and residual fractions - 53.4, 33.3 and 51.1, 24.1% respectively. The ranking of the four fractions for the partitioning of cadmium was: reducible > residual > oxidizable > acid extractable. The percentage recovery for all metals when comparing total metal concentration with the fractional sum of the optimized BCR procedure, were of the order: Zn(93%) > Pb(83%) > Cu(78) > Cd > (68%) > Ni(63%).     

Trace element concentrations in soil, corn leaves, and grain after cessation of biosolids applications

From 1974 to 1984, 543 Mg ha(-1) of biosolids were applied to portions of a land-reclamation site in Fulton County, IL. Soil organic C increased to 5.1% then decreased significantly (p < 0.01) to 3.8% following cessation of biosolids applications (1985-1997). Metal concentrations in amended soils (1995-1997) were not significantly different (p > 0.05) (Ni and Zn) or were significantly lower (p < 0.05) (6.4% for Cd and 8.4% for Cu) than concentrations from 1985-1987. For the same biosolids-amended fields, metal concentrations in corn (Zea mays L.) either remained the same (p > 0.05, grain Cu and Zn) or decreased (p < 0.05, grain Cd and Ni, leaf Cd, Cu, Ni, Zn) for plants grown in 1995-1997 compared with plants grown immediately following termination of biosolids applications (1985-1987). Biosolids application increased (p < 0.05) Cd and Zn concentrations in grain compared with unamended fields (0.01 to 0.10 mg kg(-1) for Cd and 23 to 28 mg kg(-1) for Zn) but had no effect (p > 0.05) on grain Ni concentrations. Biosolids reduced (p < 0.05) Cu concentration in grain compared with grain from unamended fields (1.9 to 1.5 mg kg(-1)). Biosolids increased (p < 0.05) Cd, Ni, and Zn concentrations in leaves compared with unamended fields (0.3 to 5.6 mg kg(-1) for Cd, 0.2 to 0.5 mg kg(-1) for Ni, and 32 to 87 mg kg(-1) for Zn), but had no significant effect (p > 0.05) on leaf Cu concentrations. Based on results from this field study, USEPA's Part 503 risk model overpredicted transfer of these metals from biosolids-amended soil to corn.     

The characterization of total and leachable metals in foundry molding sands

Waste molding sands from the foundry industry have been successfully used as a component in manufactured soils, but concern over metal contamination must be addressed before many states will consider this beneficial use. Since there is little data available on this topic, the purpose of this study was to characterize total and leachable metals from waste molding sands. A total elemental analysis for Ag, Al, As, B, Ba, Be, Cd, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, Sb, V, and Zn was conducted on 36 clay-bonded and seven chemically bonded molding sands. Total metal concentrations in the molding sands were similar to those found in agricultural soils. The leaching of metals (i.e. Ag, As, Ba, Be, Cd, Cr, Cu, Ni, Pb, Sb, and Zn) was assessed via the toxicity characteristic leaching procedure (TCLP), synthetic precipitation leaching procedure (SPLP), and ASTM water leach test. Based on the TCLP data, none of the 43 molding sands would meet the Resource Conservation and Recovery Act (RCRA) characteristic for toxicity due to high Ag, As, Ba, Cd, Cr, and Pb. Compared to the TCLP results, the metal concentrations were generally lower in the SPLP and ASTM extracts, which is likely related to the buffering capacity of the extraction fluids.     

Source-separated municipal solid waste compost application to Swiss chard and basil

A growth room experiment was conducted to evaluate the bioavailability of Cu, Mn, Zn, Ca, Fe, K, Mg, P, S, As, B, Cd, Co, Cr, Hg, Mo, Na, Ni, Pb, and Se from a sandy loam soil amended with source-separated municipal solid waste (SSMSW) compost. Basil (Ocimum basilicum L.) and Swiss chard (Beta vulgaris L.) were amended with 0, 20, 40, and 60% SSMSW compost to soil (by volume) mixture. Soils and compost were sequentially extracted to fractionate Cu, Pb, and Zn into exchangeable (EXCH), iron- and manganese-oxide-bound (FeMnOX), organic-matter (OM), and structurally bound (SB) forms. Overall, in both species, the proportion of Cu, Pb, and Zn levels in different fractions followed the sequence: SB > OM > FeMnOX > EXCH for Cu; FeMnOX = SB > OM > EXCH for Pb; and FeMnOX > SB = EXCH > OM for Zn. Application of SSMSW compost increased soil pH and electrical conductivity (EC), and increased the concentration of Cu, Pb, and Zn in all fractions, but not EXCH Pb. Basil yields were greatest in the 20% treatment, but Swiss chard yields were greater in all compost-amended soils relative to the unamended soil. Basil plants in 20 or 40% compost treatments reached flowering earlier than plants from other treatments. Additions of SSMSW compost to soil altered basil essential oil, but basil oil was free of metals. The results from this study suggest that mature SSMSW compost with concentrations of Cu, Pb, Mo, and Zn of 311, 223, 17, and 767 mg/kg, respectively, could be used as a soil conditioner without phytotoxic effects on agricultural crops and without increasing the normal range of Cu, Pb, and Zn in crop tissue. However, the long-term effect of the accumulation of heavy metals in soils needs to be carefully considered.     

Sorption of hazardous metals from single and multi-element solutions by saltbush biomass in batch and continuous mode: interference of calcium and magnesium in batch mode

Batch studies were performed to determine the interference of calcium (Ca) and magnesium (Mg) on the sorption of Cu(II), Cd(II), Cr(III), Cr(VI), Pb(II), and Zn(II) [from CuSO(4), K(2)Cr(2)O(7), Pb(NO(3))(2), Cr(NO(3))(3), ZnCl(2), and Cd(NO(3))(2)] by saltbush (Atriplex canescens) biomass. The results demonstrated that Ca and Mg at concentrations of at least 20 times higher than the concentration of most of the target metals did not interfere with the metal binding. The data show that the batch binding capacity from a multimetal solution at pH 5.0 was (micromol/g) about 260 for Cr(III) and Pb, and about 117, 54, and 49 for Cu, Zn, and Cd, respectively. The use of 0.1M HCl allowed the recovery of 85-100% of the bound Cu, Cr(III), and Pb, and more than 37% of the bound Cd and Zn. The column binding capacity for Pb was about 49 micromol/g from both the single and multimetal solutions, while it was, respectively about 35 and 23 micromol/g for Cr(III). The binding capacity for Cu and Zn from the single and multimetal column experiments was 35 micromol/g and less than 10 micromol/g, respectively. The stripping data from the single column experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and Zn, 90% and 74% of the bound Pb and Cr(VI), respectively, and less than 25% of the bound Cd and Cr(III), while the stripping from the multimetal experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and about 74%, 54%, 43%, and 40% of the bound Pb, Zn, Cd, and Cr(III), respectively.     

Assessment of the Effectiveness of Environmental Dredging in South Lake,China

Environmental dredging is a primary remedial option for removal of the contaminated material from aquatic environment. Of primary concern in environmental dredging is the effectiveness of the intended sediment removal. A 5-year field monitoring study was conducted to assess the effectiveness of the environmental dredging in South Lake, China. The concentrations of total nitrogen (TN), total phosphors, and heavy metals (Zn, Pb, Cd, Cu, Cr, Ni, Hg, and As) before and after dredging in sediment were determined and compared. Multiple ecological risk indices were employed to assess the contamination of heavy metals before and after dredging. Our results showed that the total phosphorus levels reduced 42% after dredging. Similar changes for Hg, Zn, As Pb, Cd, Cu, Cr, and Ni were observed, with reduction percentages of 97.0, 93.1, 82.6, 63.9, 52.7, 50.1, 32.0, and 23.6, respectively, and the quality of sediment improved based on the criterion of Sediment Quality Guidelines by USEPA and contamination degree values (C_d) decreased significantly (paired t-test, p < 0.05). Unexpectedly, the TN increased 49% after dredging compared to before dredging. Findings from the study demonstrated that the environmental dredging was an effective mechanism for removal of total phosphorus and heavy metals from South Lake. Nevertheless, the dredging was ineffective to remove total nitrogen from sediment. We conclude that the reason for the observed increase in TN after dredging was likely ammonia release from the sediment impairing the dredging effectiveness.     

Heavy metal release from contaminated soils: comparison of column leaching and batch extraction results

Heavy metals in soils may adversely affect environmental quality. In this study, we investigated the release of Zn, Cd, Pb, and Cu from four contaminated soils by column leaching and single and sequential batch extractions. Homogeneously packed soil columns were leached with 67 mL/g 10(-2) M CaCl2 to investigate the exchangeable metal pool and subsequently with 1400 mL/g 10(-2) M CaCl2 adjusted to pH 3 to study the potential of metal release in response to soil acidification. In two noncalcareous soils (pH 5.7 and 5.1), exchange by Ca resulted in pronounced release peaks for Zn and Cd that were coupled to the exchange of Mg by Ca, and 40 to 70% of total Zn and Cd contents were rapidly mobilized. These amounts compared well with exchangeable pools determined in single and sequential batch extractions. In two soils with near-neutral pH, the effluent concentrations of Zn and Cd were several orders of magnitude lower and no pronounced elution peaks were observed. This behavior was also observed for Cu and Pb in all four soils. When the soils were leached at pH 3, the column effluent patterns reflected the coupling of CaCO3 dissolution (if present) and other proton buffering reactions, proton-induced metal release, and metal-specific readsorption within the soil column. Varying the flow rate by a factor of five had only minor effects on the release patterns. Overall, Ca exchange and subsequent acidification to pH 3 removed between 65 and 90% of total Zn, Cd, Pb, and Cu from the four contaminated soils.     

A study on evaluation of probable sources of heavy metal pollution in groundwater of Kalpakkam region, South India

This study investigates the heavy metal pollution vulnerability of the groundwater in the coastal aquifers of Kalpakkam region in the state of Tamilnadu, India. Integrated-approach includes pollution evaluation indices, principal component analysis (PCA), and correlation matrix (CM) to evaluate the intensity and source of pollution in groundwater. The data have been used for the calculation of heavy metal pollution index (HPI) and degree of contamination (C _d). The mean metal levels in groundwater followed a descending order as: Zn?>?Ba?>?Fe?>?Al?>?Se?>?Mn?>?Cu?>?Ni?>?Pb?>?Cr?>?Mo?>?As?>?Cd?>?Sb?>?Be. The concentrations of Fe, Cd, Zn, Se, Ba, Mn, Ni, Pb, and Al in some of the groundwater samples exceed the maximum admissible concentration (MAC). The HPI and C _d yield different results despite significant correlations between them. The following elemental associations were obtained from PCA and CM: Fe?CMn?CNi?CCr?CPb?CCd?CZn?CBe?CAl, Cu?CAs, Sb?CAs, Al?CBa and Se?CMo, which could be linked to anthropogenic sources (i.e., processes of tannery and dying industries with some contribution from the landfill leachate and municipal sewage). GIS-based factor score maps suggest that the activities of tannery industries and landfill leachate are pervasive processes in the area. This study has provided the evidence that effluents discharged from the tannery and auxiliary industries and landfill leachate are the main sources of heavy metal pollution in the groundwater. The high metal concentrations observed in the groundwater may have serious public health and potential environmental hazard implications.     

Dual-function growth medium and structural soil for use as porous pavement

Permeable grass-covered surfaces can reduce the quantity of storm water runoff and filter out potentially harmful chemicals. The objective of this study was to develop permeable structural soils that sustained healthy turf growth and filtered heavy metals from contaminated pavement runoff. The basic soil medium was a 50:50 mixture (v/v) of expanded shale (ExSh) and quartz sand (QS). The ExSh component consisted of (i) large-diameter particles (3-6 mm), (ii) small-diameter particles (1-3 mm), or (iii) a 50:50 mixture (v/v) of the two. The basic blends were mixed with 0, 10, and 20% sphagnum peat moss (v/v) and 0, 10, and 20% natural zeolites (v/v) and placed in 15-cm-diameter pots in a greenhouse. Bermudagrass plugs were planted in each pot. The addition of sphagnum peat moss to the basic ExSh/QS blend increased bermudagrass growth and improved plant response to added fertilizer. Zeolites had no significant effect on plant growth in the absence of sphagnum peat moss. Growing mediums that contained 10 to 20% sphagnum peat moss and 10 to 20% zeolites consistently produced more bermudagrass biomass than the unamended ExSh/QS mixture. Changing the ratio of small- to large-diameter ExSh in the basic medium did not affect bermudagrass yield. Very low amounts of Cd, Cu, Pb, and Zn were recovered in leachate after the addition of 10 mg metal per pot, suggesting that most heavy metals (>99%) were retained in the growing mediums. Zeolites reduced the amount of Cd and Pb in leachate water, but not Cu or Zn.     

Heavy metals distribution in an Iowa suburban landscape

This study investigated the degree to which human activities through urbanization influence heavy metal concentrations in a suburban landscape in Ankeny, IA. Residential areas from different years in nine time periods of development were identified from aerial photos. Soil cores were collected from the center of the front yard of 10 randomly selected homes. Cores were subdivided into 0- to 5-, 5- to 10-, and 10- to 20-cm increments from a composite of five cores. The soils were analyzed for organic C, pH, and total Cd, Co, Cr, Cu, Ni, Pb, and Zn. Results showed that organic C increased and pH decreased with time, and that there was a general decreasing trend in heavy metal concentrations from the pre-1939 period until 1983-1990, after which there was a sharp increase in the concentrations of most of the metals. The mean Cu concentration ranged from 21 mg kg(-1) for the pre-1939 time period of development to 14.9 mg kg(-1) for the recent period of development (2003-2005). Nickel concentrations increased significantly with depth with means of 21.3 mg kg(-1) at depth 0 to 5 cm, 22.5 mg kg(-1) at depth 5 to 10 cm, and 23.0 mg kg(-1) at depth 10 to 20 cm. The concentrations of heavy metals were significantly intercorrelated, except Zn, suggesting their coexistence as mineral constituents or common contamination source. The concentrations of Cu and Pb in some locations could be due to anthropogenic inputs or higher organic matter content in soils adjacent to older homes. There appears to have been a source that caused an increase in Cd, Cr, Co, Cu, Pb, and Ni concentrations in soil adjacent to homes built between 1983 and 1990.     

Geochemical partitioning of copper, lead, and zinc in benthic, estuarine sediment profiles

The geochemical partitioning of copper (Cu), lead (Pb), and zinc (Zn) was examined in benthic sediment profiles (0- to 20-cm depth interval) composed of relatively coarse (65-90% sand-sized particles), noncohesive, suboxic material (Eh +120 to +260 mV). Total Cu, Pb, and Zn concentrations ranged from 8.3 to 194, 16.3 to 74.8, and 30.1 to 220 mg/kg, respectively, and were related to vertical trends in sediment texture. The observed distribution coefficients describing solid-solution partitioning were in the range of 100 to 1000 L/kg. The geochemical partitioning of solid-phase Cu, Pb, and Zn between six operationally defined fractions was examined with a sequential extraction scheme. The association of Cu, Pb, and Zn with amorphous oxides, crystalline oxides, and organic matter was linearly dependent on the abundance of each respective phase. For retention by amorphous oxide minerals, the observed stoichiometry ranged from 5.2 to 23.7 mg/g for Cu, 12.8 to 21.5 mg/g for Pb, and 23.1 to 85.7 mg/g for Zn. Corresponding values for association with crystalline oxides were an order of magnitude less than those for amorphous oxides, indicating a lesser affinity of trace metals for crystalline oxides. The stoichiometric relationships describing association with organic matter ranged from 17.6 to 54.0 mg/g for Cu, 6.1 to 9.6 mg/g for Pb, and 6.4 to 16.4 mg/g for Zn. The results from this study provide an insight into processes controlling trace metal partitioning in coarse-textured, suboxic, estuarine sediments.     

Use of cattails in treating wastewater from a Pb/Zn mine

This article describes the use of a combined treatment system, which includes an aquatic treatment pond withTypha latifolia Linn. (Typhaceae) as the dominant species and a stabilization pond, to treat the wastewater from a Pn/Zn mine at Shaoguan, Guangdong Province, China. In 1983, it was noted thatT. latifolia bloomed in areas affected by the wastewater emitted from the mine, hence a combined purification system was subsequently built. The influent contained high levels of total suspended solids (4635 mg/liter), chemical oxygen demand (14.5 mg/liter) as well as Pb (1.6 mg/liter) and Zn (1.9 mg/liter). The results of the effluent after treatment showed that the total suspended solids, chemical oxygen demand, Pb, and Zn had been reduced by 99%, 55%, 95%, and 80% respectively. The results of plant tissue analysis indicled thatT. latifolia assimilated significant amounts of Pb and Zn, especially in the root portion. During 1986 several species of algae and fish were present in the pond, usually with a higher density in areas containing lower metal concentrations in the water. Paper was presented in part at the conference “The Use of Constructed Wetlands in Water Pollution Control” held 24–28 September 1990, Cambridge, UK.     

Effect of liming on the distribution of heavy metals in untreated industrial sewage sludge produced in Pakistan for the cultivation of <Emphasis Type="Italic">Sorghum bicolor</Emphasis> (L.)

The recycling of sewage sludge on agriculture land represents an alternative, advantageous, disposal of this waste material. The aim of the present study was to evaluate the feasibility of using industrial sewage sludge, produced in Pakistan, as a fertiliser. Agricultural soil amended with 25% (w/w) sewage sludge with or without lime treatment was used for growing a variety of sorghum (PARC-SS-1). The mobility of the heavy metals (HMs) (Cd, Cu, Cr, Ni, Pb and Zn) and metalloid (As) in the untreated industrial waste water sewage sludge (UIWS) samples were assessed by applying a modified BCR (Community Bureau of Reference) sequential extraction procedure. The single extraction procedure comprised of the application of mild extractant (CaCl₂) and water for the estimation of the proportion of easily soluble metal fractions. The precision and accuracy of BCR was evaluated by using a certified reference material of soil amended with sewage sludge BCR 483. The plant available metal contents, as extracted by the deionised water and 0.01 M CaCl₂ solution and exchangeable fraction of BCR sequential, decreased with lime application in the range of 10–44% for As, Cr, Ni, Pb and Zn, except in the cases of Cd and Cu, where their mobility was increased by 10% and 24%, respectively. Sludge amendment enhanced the dry weight yield of sorghum and the increase was more obvious after liming up to 25%. The uptake of HMs were lower in test samples (3.2–21.8%), except for Cu and Cd, which was higher (4%), while they were below the permissible limit of these metals. The present experiment demonstrates that liming was important in factors facilitating the growth of sorghum in sludge-amended soil.     

In situ stabilization of soil lead using phosphorus and manganese oxide: influence of plant growth

In situ stabilization of Pb contaminated soils can be accomplished by adding P and Mn(IV) oxide. However, the long-term efficacy of in situ stabilization under continual P removal through plant growth is unknown. Moreover, the effects these treatments have on phytoavailability of other metals (Cd and Zn) commonly associated with Pb in soil are not well understood. Greenhouse experiments using sudax [Sorghum vulgare (L.) Moench] and Swiss chard [Beta vulgaris (L.) Koch] were carried out to evaluate the effects of plant growth on soil Pb bioavailability to humans after addition of P and other amendments, and the effects of these treatments on Pb, Cd, and Zn phytoavailability in three metal-contaminated soils. Eight treatments were used: zero P; 2500 mg of P as triple superphosphate (TSP); 5000 mg of P as TSP or phosphate rock (PR); 5000 mg of Mn oxide/kg; and combinations of Mn oxide and P as TSP or PR. The addition of P and/or Mn oxide significantly reduced bioavailable Pb, as measured by the physiologically based extraction test (PBET), in soils compared with the control even after extensive cropping. The PBET data also suggested that removal of P from soluble P sources by plants could negate the beneficial effects of P on bioavailable Pb, unless sufficient soluble P was added or soluble P was combined with Mn oxide. In general, Ph, Cd, and Zn concentrations in shoot tissues of sudax and Swiss chard were reduced significantly by TSP and did not change with the addition of PR. The combination of PR and Mn oxide significantly reduced Pb concentrations in plants compared with the control.     

Heavy metal distribution and chemical speciation in tailings and soils around a Pb-Zn mine in Spain

Soil pollution by lead, zinc, cadmium and copper was characterized in the mine tailings and surrounding soils (arable and pasture lands) of an old Spanish Pb-Zn mine. Sixty soil samples were analyzed, determining the total metal concentration by acid digestion and the chemical fractionation of Pb and Zn by the modified BCR sequential extraction method. Samples belonging to mine waste areas showed the highest values, with mean concentrations of 28,453.50 mg kg(-1) for Pb, 7000.44 mg kg(-1) for Zn, 20.57 mg kg(-1) for Cd and 308.48 mg kg(-1) for Cu. High concentrations of Pb, Zn and Cd were found in many of the samples taken from surrounding arable and pasture lands, indicating a certain extent of spreading of heavy metal pollution. Acidic drainage and wind transport of dust were proposed as the main effects causing the dispersion of pollution. Sequential extraction showed that most of the Pb was associated with non-residual fractions, mainly in reducible form, in all the collected samples. Zn appeared mainly associated with the acid-extractable form in mine tailing samples, while the residual form was the predominant one in samples belonging to surrounding areas. Comparison of our results with several criteria reported in the literature for risk assessment in soils polluted by heavy metals showed the need to treat the mine tailings dumped in the mine area.