Novel Fe/glass composite adsorbent for As(V) removal

An effective adsorbent for arsenic removal was synthesized by hydrothermal treatment of waste glass powder (GP), followed by loading Fe(Ⅲ) oxyhydroxide onto the surface of waste glass powder. The ≡Si-O-H group was formed on the surface of GP and the specific surface area of GP powder was slightly increased after hydrothermal treatment. FeOOH was loaded onto the surface of hydrothermally treated waste glass powder (HGP) by the hydrolysis of FeCl3. The formation conditions of FeOOH were also investigated. The...     

铁改性杭锦土吸附剂对水中砷的去除研究

为提高天然杭锦土对水溶液中砷的吸附性能,采用氯化铁（FeCl₃·6H₂O）浸渍天然黏土矿物杭锦土（HJ）,制备表面负载铁氧化物的铁改性杭锦土除砷吸附剂（FHJ）.通过比表面积（BET）和扫描电镜（SEM）分析技术对材料进行表征以观察其微观形貌特点,通过X射线光电子能谱分析（XPS）和傅里叶红外光谱（FTIR）技术测定材料组成及化学基团,以初步探究材料吸附除砷机理.通过批试验考察FHJ投加量、初始pH、共存离子及腐殖酸浓度对FHJ除砷效能的影响.结果表明:①当铁负载比在0~50wt%范围内时,FHJ对溶液中As（Ⅴ）吸附容量随着铁负载比的增加而增加,最佳铁负载比为33wt%,此时铁与杭锦土的理论质量比为1:3.②BET分析结果表明经铁改性后,杭锦土比表面积显著增加,由71.14 m2/g增至158.50 m2/g;SEM分析显示,经改性后杭锦土表面形貌发生明显变化,结合Mapping图表明铁被有效负载到杭锦土表面.③批试验结果表明,As（Ⅴ）去除率随着FHJ投加量的增加而升高;溶液pH对As（Ⅴ）去除率有较大的影响,pH的降低有利于FHJ对砷酸盐的吸附.④FHJ除砷性能受溶液中共存离子CO₃2-、SiO₃2-影响较大,但受Cl-、SO₄2-、NO₃-及腐殖酸影响程度比较小.⑤吸附动力学过程符合准二级动力学模型,Freundlich等温吸附模型可更好地描述FHJ吸附除砷行为（R2=0.999）.⑥XPS分析结果显示,铁氧化物主要以FeOOH和Fe₂O₃的形态负载于杭锦土表面,FTIR表明FeOOH的羟基基团同As（Ⅴ）发生吸附作用,在FHJ除砷过程中,化学吸附是主要的吸附除砷机理.研究显示,铁改性杭锦土除砷效果良好,具有一定的应用潜力.      

基于铁锰泥的除砷吸附剂性能比较及吸附机理

为解决反冲洗铁锰泥粉末吸附剂（BSPA）使用后难以泥水分离问题,将除铁锰水厂生物滤池产生的反冲洗泥制成颗粒吸附剂（GA）和磁性粉末吸附剂（MPA）,并对BSPA、GA和MPA的除砷性能进行了比较,通过SEM、TED、XRD、BET、FTIR等技术对3种材料进行了表征,寻找3种吸附剂之间除砷性能差异的根源.结果表明,BSPA、GA和MPA对As （V）的最大吸附容量分别为40.980,5.048,8.694mg/g,改性后的吸附材料GA和MPA对砷的吸附能力下降.BSPA是一种以纤铁矿为主的无定形结构混合物,并混有针铁矿和结晶度差的水铁矿,GA的XRD图谱中出现石英晶体和少量赤铁矿晶体的衍射峰,而MPA的主要成分为结晶程度较高的磁赤铁矿.3种材料中均存在有利于吸附的含羟基官能团.BSPA、MPA和GA的比表面积分别为253.150,238.660,43.803m²/g.物相改变且结晶程度增加、表面羟基减少和比表面积降低是导致GA和MPA的砷吸附容量比BSPA低的主要因素.     

Modified activated carbon with interconnected fibrils of iron-oxyhydroxides using Mn2 + as morphology regulator, for a superior arsenic removal from water

The arsenic removal efficiency of iron-modified activated carbons depends greatly on the number of available iron oxide surface sites, which are given by the surface area of the anchored particles. In this sense, aiming the generation of an adsorbent with superior arsenic adsorption capacity, we developed a protocol to anchor interconnected fibrils of iron oxyhydroxides, using Mn^2 + as a morphology regulator. The protocol was based on a microwave-assisted hydrothermal method, using bituminous based activated carbon and both Fe^2 + and Mn^2 + ions in the hydrolysis solution. The elemental analysis of modified carbons revealed that Mn does not anchor to the carbon. However, when Mn is included in the hydrolysis solution, the iron content in the activated carbon increased up to 3.5?wt%, without considerable decreasing the adsorbent surface area. Under specific hydrothermal conditions, the Mn^2 + promoted the formation of iron oxide nanoparticles shaped as interconnected fibrils. This material showed a superior arsenic adsorption capacity in comparison to similar iron modified activated carbons (5?mg As/g carbon, at 2?mg As/L), attributed to the increase in quantity and availability of active sites located on the novel interconnected fibrils of iron oxyhydroxides nanostructures.     

载铁(β-FeOOH)球形棉纤维素吸附剂去除地下水As(Ⅴ)的研究

制备了一种载铁(β- FeOOH)球形棉纤维素吸附剂,球珠孔隙度大,强度好,活性成分铁的载入量可高达360mg/mL ,(质量分数达50%) ,活性好.研究表明,当铁含量为220mg/mL时,该吸附剂对As(V)的最大吸附量为15.6mg/mL(33.2mg/g) ,Langmuir和Freundlich方程能很好地描述吸附等温线.吸附速度较快,10h可达到吸附平衡,吸附动力学符合Lagergren二级方程.SiO₃^2- ,SO₄^2-,Cl^-干扰离子均不影响砷的去除.柱吸附实验表明,空床停留时间为5.9min ,进水As(V)浓度为500μg/L时,As(V)的穿透体积为5000BV .吸附剂可以用1.5mol·L^-1 NaOH再生,洗脱和再生效率可达90%以上.活性成分β-FeOOH形态稳定,柱操作和再生时铁无溶出.吸附剂制备方法简单,新颖,对地下水和饮用水砷去除具有较好的应用前景.     

活化赤泥去除猪场废水生化处理出水中的磷和重金属

以铝矿工业废渣赤泥为原材料,采用焙烧活化方法进行活化处理,并将其用于畜禽废水生化处理出水中磷和重金属的吸附去除.同时,研究考察了吸附剂除磷、除重金属的能力以及投加量、pH值和反应时间对去除效果的影响.结果表明,赤泥和活化赤泥对磷、铜、锌、砷吸附规律符合Langmuir吸附等温方程;焙烧改性后,赤泥对磷、铜、锌、砷的去除能力显著提高,900℃焙烧活化饱和吸附量可分别由46.26、18.18 、15.45、18.83 mg·g-1提高至149.00、65.17、99.20、27.51 mg·g-1;pH显著影响除磷、除重金属的效果,高pH条件有利于磷、铜、锌、砷的去除;赤泥和活化赤泥除磷、铜、锌、砷的作用机理包含金属氧化物表面的表面络合作用机理,其对砷和磷的去除机理还包括共沉淀作用.     

天然菱铁矿改性及强化除砷研究

我国高砷地下水分布广泛,经济、高效地饮用水除砷技术受到广泛关注.静态批实验采用资源丰富、价格便宜的天然菱铁矿为主要原材料,考虑灼烧温度、时间及添加黏合剂等因素确定最优改性条件使除砷效果达到最佳.结果表明,在加铝量为10 mg.g-1、350℃下恒温灼烧90 min后造粒达到强度要求并除砷效果较优.25℃、固液比为0.5 g∶50 mL、As(Ⅲ)和As(Ⅴ)初始浓度为5 mg.L-1时,吸附后溶液中残留As浓度均<10μg.L-1.静态吸附批实验结果表明,25℃时,接触反应时间为12 h可达到吸附平衡,吸附过程较好地符合Lagergren假二级吸附速率方程;最优改性天然菱铁矿对砷的吸附规律可用Langmuir和Freundlich等温吸附模型很好地描述,As(Ⅲ)、As(Ⅴ)饱和吸附容量分别可以达到1 039、1 026μg.g-1.结合XRD、SEM等研究方法和比表面及孔结构分析初步探讨天然菱铁矿改性以及除砷的主要机制.分析表明,改性后天然菱铁矿比表面积大幅度增大,孔径减小,且在表面活化生成一层圆球状的含Fe(Ⅱ)和Fe(Ⅲ)的化合物.改性天然菱铁矿是一种值得进一步研究并实际应用的除砷材料.     

载钠硅碳羟基磷灰石的制备及其对水中As(Ⅴ)的吸附特性

由于自然和人为活动导致自然水体和土壤被As（砷）污染,严重危及生态环境并已受到广泛关注.为实现更大程度地去除含As废水的新型吸附材料,以废弃蛋壳为原材料,采用超声波法制备多孔状且较大比表面积的Na-Si-CHAP[Ca_10-xNa_x（PO₄）_6-y-z（SiO₄）_z（CO₃）_y（OH）_2-α,载钠硅碳羟基磷灰石],深入分析去除含As（Ⅴ）废水的吸附特性.通过BET比表面积、扫描电镜（SEM）、EDX（能量色散X射线光谱）、X-射线衍射（XRD）等手段对样品进行表征,并进一步探讨了pH、吸附时间、初始ρ[As（Ⅴ）]以及反应温度等因素对吸附效果的影响.结果表明:在pH为6.0、作用时间为60 min、反应温度为313 K等优化条件下,0.2 g Na-Si-CHAP对100 mL 30 mg/L含As（Ⅴ）废水的去除率和平衡吸附容量分别为96.53%和14.48 mg/g.Langmuir等温吸附模型较好地拟合了吸附试验数据,313 K下相关系数（r2）高达0.998 0,饱和吸附容量达46.73 mg/g,明显高于其他同类材料;准二级动力学模型可较好地描述该吸附行为,相关系数高达0.999 9;热力学参数△G（吉布斯自由能变）、△H（焓变）和△S（熵变）的计算值显示,该吸附过程为自发吸热过程.研究显示,Na-Si-CHAP作为一种吸附剂,对含As（Ⅴ）的去除效果明显优于同类材料.      

磁性吸附材料CuFe2O4吸附砷的性能

根据Cu(Ⅱ)和Fe(Ⅲ)都对砷有较强的亲和性,制备了同时含有Cu(Ⅱ)和Fe(Ⅲ)的、可用磁分离方法进行分离回收的磁性吸附材料CuFe₂O₄,并对其进行了表征及吸附砷的性能研究.结果表明,该吸附剂对砷的吸附能力与溶液pH有关,在弱酸性及中性条件下,吸附砷的能力最强,而对As(V)的吸附能力比对As(Ⅲ)更强些,在平衡浓度为10μg/L时,其吸附容量可达10mg/g左右,可以很容易地将水中浓度为1～20mg/L的As(V)降到10μg/L以下.实验考察了几种无机阴离子对吸附砷的影响,表明较高浓度(砷浓度的20倍)的硫酸盐对As(Ⅲ)和As(V)的吸附均有一定影响,盐酸盐及磷酸盐则影响不明显;负载的As(V)可较容易地用0.1mol/L NaOH洗脱下来,使吸附剂再生,而As(Ⅲ)则难以洗脱,这与2种价态砷的吸附机理不同有关.     

CTAB改性地聚合物同时去除Cu(II)和Cr(VI)

地聚合物（Geopolymer,简称GP）是由含硅铝酸盐的偏高岭土（Metakaolin,简称MK）或固体废料（如粉煤灰）经碱性激活制备的立体网状结构无机聚合物,对大部分重金属阳离子有良好的吸附作用,但对以阴离子形态存在的重金属吸附效果很差.本研究以偏高岭土为主要原料制备GP,同时用CTAB进行改性,研究其化学组成变化及对典型以阴、阳离子形态存在的重金属Cr（VI）和Cu（II）的同时吸附作用.结果表明,pH为5、吸附时间为24 h、初始浓度为50 mg·L^-1、吸附剂投加量为1 g·L^-1时,CTAB-GP对Cu（II）的去除率达到98.6%,Cr（VI）的最高去除率为25.6%,同时还发现溶液中Cu（II）的存在对吸附Cr（VI）有较大促进作用.整体来看,两种金属混合吸附时很好地符合二级动力学规律,单溶质吸附很好地符合Langmuir和Freundlich等温式,Cu（II）和Cr（VI）的理论最大吸附量分别为147.1 mg·g^-1和63.1 mg·g^-1.XRD、FTIR和BET表征分析结果表明,CTAB-GP中即使存在季铵盐阳离子,但依然属于地聚合物.CTAB-GP可以不牺牲对重金属阳离子吸附性能的同时吸附阴离子,优于常规地聚合物,鉴于CTAB-GP的这种特性,其在重金属污染防治中显示出极大的应用前景.     

Sequestration of toxic Pb(Ⅱ) ions by chemically treated rubber(Hevea brasiliensis) leaf powder

Rubber leaf powder(an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(Ⅱ) ions from aqueous solution was evaluated.The interactions between Pb(Ⅱ) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared(FT-IR) spectroscopy,scanning electron microscopy(SEM) coupled with X-ray energy dispersive spectroscopy(EDX).The effects of several important parameters which can affect adsorption capacity such as pH,adsorbent dosage,initial lead concentration and contact time were studied.The optimum pH range for lead adsorption was 4-5.Even at very low adsorbent dosage of 0.02 g,almost 100% of Pb(Ⅱ) ions(23 mg/L) could be removed.The adsorption capacity was also dependent on lead concentration and contact time,and relatively a short period of time(60-90 min) was required to reach equilibrium.The equilibrium data were analyzed with Langmuir,Freundlich and Dubinin-Radushkevich isotherms.Based on Langmuir model,the maximum adsorption capacity of lead was 95.3 mg/g.Three kinetic models including pseudo first-order,pseudo second-order and Boyd were used to analyze the lead adsorption process,and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.     

Sequestration of toxic Pb（II） ions by chemically treated rubber （Hevea brasiliensis ） leaf powder

Rubber leaf powder (an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(II) ions from aqueous solution was evaluated. The interactions between Pb(II) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) coupled with X-ray energy dispersive spectroscopy (EDX). The effects of several important parameters which can affect adsorption capacity such as pH, adsorbent dosage, initial lead concentration and contact time were studied. The optimum pH range for lead adsorption was 4–5. Even at very low adsorbent dosage of 0.02 g, almost 100% of Pb(II) ions (23 mg/L) could be removed. The adsorption capacity was also dependent on lead concentration and contact time, and relatively a short period of time (60–90 min) was required to reach equilibrium. The equilibrium data were analyzed with Langmuir, Freundlich and Dubinin-Radushkevich isotherms. Based on Langmuir model, the maximum adsorption capacity of lead was 95.3 mg/g. Three kinetic models including pseudo first-order, pseudo second-order and Boyd were used to analyze the lead adsorption process, and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.     

铜渣与含砷污酸反应行为及除砷机理

分析铜渣组成结构和形貌特性的基础上,研究了铜渣与含砷污酸反应行为及脱砷规律,阐明了反应动力学过程,揭示了铜渣除砷机理.结果表明：在铜渣用量为0.2g/mL,反应温度为23℃,反应时间为24h的最优条件下,铜渣的最大去除容量达到25.89mg/g,除砷率达到99.56%,并且除砷后铜渣的砷浸出浓度低于5mg/L的危险废弃物界定限值,属于一般固体废弃物.铜渣除砷过程符合拟二级动力学模型,该过程受铁离子释放速度限制,离子交换吸附和化学沉淀方式同步进行实现了砷的脱除,两种方式的结合有利于砷的稳定化.铜渣与污酸反应释放大量的铁离子,通过离子交换吸附与砷酸根离子发生沉淀反应,形成较为稳定的砷酸盐及其衍生化合物,进而达到除砷目的.铜渣表现出优越的除砷性能,为重有色冶炼污酸处置提供了一种高效和低成本的方法.     

Modification of a magnetic carbon composite for ciprofloxacin adsorption

A magnetic carbon composite, Fe₃O₄/C composite, was fabricated by one-step hydrothermal synthesis, modified by heat treatment under an inert atmosphere (N₂), and then used as an adsorbent for ciprofloxacin (CIP) removal. Conditions for the modification were optimized according to the rate of CIP removal. The adsorbent was characterized by Fourier transform infrared spectroscopy, X-ray diffraction measurements, vibrating-sample magnetometry, scanning electron microscopy, transmission electron microscopy, and N₂ adsorption/desorption isotherm measurements. The results indicate that the modified adsorbent has substantial magnetism and has a large specific area, which favor CIP adsorption. The effects of solution pH, adsorbent dose, contact time, initial CIP concentration, ion strength, humic acid and solution temperature on CIP removal were also studied. Our results show that all of the above factors influence CIP removal. The Langmuir adsorption isotherm fits the adsorption process well, with the pseudo second-order model describing the adsorption kinetics accurately. The thermodynamic parameters indicate that adsorption is mainly physical adsorption. Recycling experiments revealed that the behavior of adsorbent is maintained after recycling for five times. Overall, the modified magnetic carbon composite is an efficient adsorbent for wastewater treatment.     

脱硫石膏基羟基磷灰石对Cu2+吸附性能的研究

以燃煤电厂废弃物脱硫石膏(FGD)为主要原料,利用水热合成法制备羟基磷灰石(FGD-HA),利用XRD和SEM对FGD-HA的物相组成和微观形貌进行了分析和观察.通过静态吸附实验研究了吸附动力学、吸附等温线以及吸附热力学.结果表明,伪二级动力学模型相关系数为0.9998,是描述FGD-HA吸附Cu2+的最佳动力学模型,Cu2+在FGD-HA上的吸附平衡符合Langmuir等温线模型(R2=0.9846),热力学表明此吸附是自发吸热的过程.利用响应面分析法对Cu2+的吸附条件进行优化,得出投加量3.11g/L、pH值4.96、温度22.09℃、Cu2+初始浓度24.75mg/L为最佳吸附条件,此条件下Cu2+去除率预测值为100%,相同条件下开展的验证实验结果为97.4%,与预测值相接近说明模型的选择是实际可行的.     

基于铁锰泥的除砷颗粒吸附剂制备及其比较

地下水除铁除锰滤池反冲洗铁锰泥具有良好的除砷效果,但因其粉末形态不易固液分离,本文采用高温烘焙法和包埋法以铁锰泥为原料制备颗粒吸附剂,其中包埋法采用烘干和冻干两种干燥方法制粒.结果表明,3种颗粒吸附剂:高温烘焙颗粒吸附剂(GA)、包埋烘干吸附剂(H-GA)和包埋冻干吸附剂(D-GA),表面粗糙,比表面积分别为43. 830、110. 30和129. 18 m~2·g~(-1).吸附实验表明,H-GA和D-GA对砷的吸附远大于GA,GA、H-GA和D-GA最大吸附量分别为5. 05、14. 95和13. 45 mg·g~(-1). Langmuir模型能更好地拟合H-GA和D-GA对砷的吸附,Freundlich模型更好地拟合GA的吸附过程,准一级动力学和准二级动力学模型均能拟合3种吸附剂的动力学数据.酸性环境更有利于砷的吸附.包埋法制备的颗粒吸附剂H-GA和D-GA保留了铁锰泥原始结构,比表面积也远大于GA,因此吸附效果比GA好.两种干燥方式烘干和冻干对吸附没有明显影响.     

Removal of phosphate by Fe-coordinated amino-functionalized 3D mesoporous silicates hybrid materials

Phosphate removal from aqueous waste streams is an important approach to control the eutrophication downstream bodies of water. A Fe(III) coordinated amino-functionalized silicate adsorbent for phosphate adsorption was synthesized by a post-grafting and metal cation incorporation process. The surface structure of the adsorbent was characterized by X-ray di raction, N2 adsoropion/desoprotion technique, and Fourier transform infrared spectroscopy. The experimental results showed that the adsorption equilibrium data were well fitted to the Langmuir equation. The maximum adsorption capacity of the modified silicate material was 51.8 mg/g. The kinetic data from the adsorption of phosphate were fitted to pseudo second-order model. The phosphate adsorption was highly pH dependent and the relatively high removal of phosphate fell within the pH range 3.0–6.0. The coexistence of other anions in solutions has an adverse e ect on phosphate adsorption; a decrease in adsorption capacity followed the order of exogenous anions: F?? > SO2?? 4 > NO??3 > Cl??. In addition, the adsorbed phosphate could be desorbed by NaOH solutions. This silicate adsorbent with a large adsorption capacity and relatively high selectivity could be utilized for the removal of phosphate from aqueous waste streams or in aquatic environment.     

CTAC改性活性炭去除水中砷(V)的柱实验吸附和再生研究

为了开发一种能有效去除水中砷的吸附材料, 研究了十六烷基三甲基氯化铵(CTAC)改性活性炭后, 活性炭对水中五价砷As(V)的去除效果.研究中利用动态小柱实验(Rapid small-scale column test, RSSCT)探讨了CTAC改性后活性炭对砷的吸附能力、影响吸附能力的因素和活性炭再生方法.结果表明, CTAC改性能有效提高活性炭对As(V)的吸附.活性炭对As(V)的吸附受溶液pH、空床接触时间、进水中砷浓度及水中其他离子存在的影响.另外, 1 mol·L^-1的盐酸能有效对吸附穿透后的活性炭进行再生,再生后的活性炭可以重复使用.同时,柱实验中对出水CTAC的检测结果表明, CTAC和活性炭的结合非常稳定.     

Efficient capture of aqueous humic acid using a functionalized stereoscopic porous activated carbon based on poly(acrylic acid)/food-waste hydrogel

Stereoscopic porous carbons have shown good potential in humic acid (HA) removal. In this work, a novel stereoscopic porous activated carbon (SPAC) was designed and synthesized via the self-assembly of a hydrogel based on food waste during in-situ polymerization, vacuum drying, carbonization, and activation. Then, the SPAC was functionalized with 3-aminopropyltriethoxysilane (APTES) and the adsorption behavior of the modified SPAC (SPAC-NH₂) was studied systematically. The effects of pH, contact time, initial concentration of HA, and adsorbent dose were investigated, showing that optimal HA removal efficiency (> 98.0%) could be achieved at an initial HA concentration of 100?mg/L. The experimental adsorption isotherm data was fitted to the Langmuir model with a maximum adsorption capacity of 156.0?mg?HA/g SPAC-NH₂. Analysis of the mechanism indicated that the removal of HA was mainly realized through the amidization reaction between the COOH groups of HA and the NH₂ groups of APTES. All of the above results showed that SPAC-NH₂ powder is an efficient, eco-friendly, and reusable adsorbent which is suitable for the removal of HA from wastewater.     

Removal of arsenate and arsenite from aqueous solution by waste cast iron

The removal of As(III) and As(V) from aqueous solution was investigated using waste cast iron, which is a byproduct of the iron casting process in foundries. Two types of waste cast iron were used in the experiment: grind precipitate dust (GPD) and cast iron shot (CIS). The X-ray diffraction analysis indicated the presence of Fe0 on GPD and CIS. Batch experiments were performed under different concentrations of As(III) and As(V) and at various initial pH levels. Results showed that waste cast iron was effective in the removal of arsenic. The adsorption isotherm study indicated that the Langmuir isotherm was better than the Freundlich isotherm at describing the experimental result. In the adsorption of both As(III) and As(V), the adsorption capacity of GPD was greater than CIS, mainly due to the fact that GPD had higher surface area and weight percent of Fe than CIS. Results also indicated the removal of As(III) and As(V) by GPD and CIS was influenced by the initial solution pH, generally decreasing with increasing pH from 3.0 to 10.5. In addition, both GPD and CIS were more effective at the removal of As(III) than As(V) under given experimental conditions. This study demonstrates that waste cast iron has potential as a reactive material to treat wastewater and groundwater containing arsenic.