Electrokinetic remediation of heavy metal-contaminated soils under reducing environments

This paper describes the migration of hexavalent chromium, Cr(VI), nickel, Ni(II), and cadmium, Cd(II), in clayey soils that contain different reducing agents under an induced electric potential. Bench-scale electrokinetic experiments were conducted using two different clays, kaolin and glacial till, both with and without a reducing agent. The reducing agent used was either humic acid, ferrous iron, or sulfide, in a concentration of 1000 mg/kg. These soils were then spiked with Cr(VI), Ni(II), and Cd(II) in concentrations of 1000, 500 and 250 mg/kg, respectively, and tested under an induced electric potential of 1 VDC/cm for a duration of over 200 h. The reduction of chromium from Cr(VI) to Cr(III) occurred prior to electrokinetic treatment. The extent of this Cr(VI) reduction was found to be dependent on the type and amount of reducing agents present in the soil. The maximum reduction occurred in the presence of sulfides, while the minimum reduction occurred in the presence of humic acid. The concentration profiles in both soils following electrokinetic treatment showed that Cr(VI) migration was retarded significantly in the presence of sulfides due both to the reduction of Cr(VI) to Cr(III) as well as an increase in soil pH. This low migration of chromium is attributed to: (1) migration of Cr(VI) and the reduced Cr(III) fraction in opposite directions, (2) low Cr(III) migration due to adsorption and precipitation in high pH regions near the cathode in kaolin and throughout the glacial till, and (3) low Cr(VI) migration due to adsorption in low pH regions near the anode in both soils. Ni(II) and Cd(II) migrated towards the cathode in kaolin; however, the migration was significantly retarded in the presence of sulfides due to increased pH through most of the soil. Initial high pH conditions within the glacial till resulted in Ni(II) and Cd(II) precipitation, so the effects of reducing agenets were inconsequential. Overall, this study demonstrated that the reducing agents, particularly sulfides, in soils may affect redox chemistry and soil pH, ultimately affecting the electrokinetic remediation process.     

Removal of Cr6 + and Ni2+ from aqueous solution using bagasse and fly ash

Raw bagasse and fly ash, the waste generated in sugar mills and boilers respectively have been used as low-cost potential adsorbents. Raw bagasse was pretreated with 0.1N NaOH followed by 0.1N CH3COOH before its application. These low-cost adsorbents were used for the removal of chromium and nickel from an aqueous solution. The kinetics of adsorption and extent of adsorption at equilibrium are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental system. The effect of hydrogen ion concentration, contact time, sorbent dose, initial concentrations of adsorbate and adsorbent and particle size on the uptake of chromium and nickel were studied in batch experiments. The Sorption data has been correlated with Langmuir, Freundlich and Bhattacharya and Venkobachar adsorption models. The efficiencies of adsorbent materials for the removal of Cr(VI) and Ni(II) were found to be between 56.2 and 96.2% and 83.6 and 100%, respectively. These results were obtained at the optimized conditions of pH, contact time, sorbent dose, sorbate concentration of 100 mg/l and with the variation of adsorbent particles size between 0.075 and 4.75 mm. The order of selectivity is powdered activated carbon > bagasse > fly ash for Cr(VI) removal and powdered activated carbon > fly ash > bagasse for Ni(II) removal.     

Recycling of ‘waste’ FE(III)/CR(III) hydroxide for the removal of nickel from wastewater: Adsorption and equilibrium studies

Effects of Ni(II) concentration, agitation time, temperature and pH on adsorption of Ni(II) on Fe(III)/Cr(III) hydroxide, a waste by-product from fertilizer industry, have been investigated. The percent adsorption increased from 55 to 69% with increase in temperature from 20 to 40°C and from 32 to 77% with increase in pH from 3.7 to 7.5 and from 38 to 79% with decrease in Ni(II) concentration from 100 to 25 mg/L. The equilibrium data fit well with the Langmuir isotherm and the adsorption capacity was found to be 21.0 mg/g at 30°C. Thermodynamic parameters such as free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were evaluated. The adsorption rate constant was higher at lower concentration of Ni(II) and at higher temperature. Desorption studies show that 70% of Ni(II) can be desorbed from the adsorbent at pH 4.0. The adsorbent was tested using nickel plating industry wastewater and the maximum percent removal was 97.     

Removal of Cr(VI) from contaminated soil by electrokinetic remediation

A new process for the removal of hexavalent chromium [Cr(VI)] contaminated soil is described. The process provides for an efficient removal of anionic chemicals from contaminated soils. Chromate anions were removed from the soil to the anodic reservoir by the moving force of electromigration. In this process, the chromate anions that accumulate in the anodic reservoir are simultaneously eliminated by using a column packed adsorbent. The adsorbent (immobilized tannin) used was chemically incorporated into cellulose. Cr(VI) was found to be adsorbed to this adsorbent efficiently. In the electrokinetic process, the pH of the aqueous solution in the anodic reservoir was decreased by the electrolysis of water. In the present study, the pH of the solution in the anodic reservoir is maintained at pH 6 by the addition of an aqueous alkaline solution during the electrokinetic process. The advantage of pH control is that it promotes the release of Cr(VI) from the soil by electromigration, thus permitting the maximum adsorption of Cr(VI) on the immobilized tannin. Simultaneous collection of Cr(VI) from the anodic reservoir leads to the protection from secondary contamination with Cr(VI).     

Optimizing Cr(VI) adsorption on activated carbon produced from heavy oil fly ash

In order to explore the beneficial utilization of heavy oil fly ash (HOFA) generated in the power plants, the present study is intended to optimize the chromium(VI) [Cr(VI)] adsorption on activated carbon produced from HOFA. The raw HOFA obtained from a power plant was washed by nitric/hydrochloric acid and activated at 800 °C with a holding time of 60 min to produce fly ash activated carbon (FAC). Phosphoric acid was used as a chemical agent to improve the surface characteristics of the HOFA during the activation process. Batch adsorption experiments were employed to evaluate the effects of different parameters such as initial Cr(VI) concentration, pH, and FAC dose on the removal of Cr(VI) from aqueous solution. A total of 17 adsorption experimental runs were carried out employing the detailed conditions followed the response surface methodology based on the Box–Behnken design. The results indicate that developed FAC has the potential for removing Cr(VI) from wastewater. Under the test conditions, a maximum of 91.51 % Cr(VI) removal efficiency was achieved.     

Stabilization of As, Cr, Cu, Pb and Zn in soil using amendments--a review

The spread of contaminants in soil can be hindered by the soil stabilization technique. Contaminant immobilizing amendments decrease trace element leaching and their bioavailability by inducing various sorption processes: adsorption to mineral surfaces, formation of stable complexes with organic ligands, surface precipitation and ion exchange. Precipitation as salts and co-precipitation can also contribute to reducing contaminant mobility. The technique can be used in in situ and ex situ applications to reclaim and re-vegetate industrially devastated areas and mine-spoils, improve soil quality and reduce contaminant mobility by stabilizing agents and a beneficial use of industrial by-products. This study is an overview of data published during the last five years on the immobilization of one metalloid, As, and four heavy metals, Cr, Cu, Pb and Zn, in soils. The most extensively studied amendments for As immobilization are Fe containing materials. The immobilization of As occurs through adsorption on Fe oxides by replacing the surface hydroxyl groups with the As ions, as well as by the formation of amorphous Fe(III) arsenates and/or insoluble secondary oxidation minerals. Cr stabilization mainly deals with Cr reduction from its toxic and mobile hexavalent form Cr(VI) to stable in natural environments Cr(III). The reduction is accelerated in soil by the presence of organic matter and divalent iron. Clays, carbonates, phosphates and Fe oxides were the common amendments tested for Cu immobilization. The suggested mechanisms of Cu retention were precipitation of Cu carbonates and oxy-hydroxides, ion exchange and formation of ternary cation-anion complexes on the surface of Fe and Al oxy-hydroxides. Most of the studies on Pb stabilization were performed using various phosphorus-containing amendments, which reduce the Pb mobility by ionic exchange and precipitation of pyromorphite-type minerals. Zn can be successfully immobilized in soil by phosphorus amendments and clays.     

Electrochemical remediation of heavy metal contaminated soils

Over the years, many soils have been contaminated with toxic heavy metals as a result of a variety of industrial and military activities. Electrokinetic soil treatment is an emerging technology that could prove to be very effective in the remediation of these sites. “Real-world” heavy metal contaminated (Pb(II), Cd(II), and Cr(III)) soils from three military sites with varying soil properties were subjected to electrokinetic treatment in the laboratory. Metal extractants (chelating agents and acids) were studied and found to be effective in enhancing the electrokinetic process. Results indicated that heavy metal removal efficiencies varied in the three soils tested. In one case, removal efficiencies of 90 percent and 60 percent were obtained for Cd and Cr, respectively, for the nitric acid amended experiments. For another case, over 60 percent of the total Pb in the system was deposited near the cathode for the non-amended and the citric-acid amended tests. Conversely, in the third case, the electrokinetic soil-washing treatment process failed to produce significant removal of any metal contaminant. The discrepancies that exist between the metal removal results of the three soils were attributed to the different physiochemical characteristics of each soil.     

Fabrication of Polypyrrole/Chitosan Nanocomposite Aerogel Monolith for Removal of Cr(VI)

Three-dimensional polypyrrole/chitosan nanocomposite monoliths are fabricated by polymerization of pyrrole in chitosan aqueous solution. The static polymerization of pyrrole monomer and the cross-linking of chitosan by glutaraldehyde occur simultaneously, resulting in the self-assembly of polypyrrole/chitosan nanocomposite aerogel monolith. The addition of methyl orange and glutaraldehyde and the static reaction play key roles in the formation of the self-standing aerogel monolith. The as-prepared monolith with larger specific surface area exhibits much better adsorption capability for Cr(VI) removal in comparison with that prepared without the addition of glutaraldehyde. The adsorption process and adsorption isotherms are found to well follow the pseudo-second-order and Langmuir models, respectively. Furthermore, this polypyrrole/chitosan nanocomposite monolith is stable and recyclable. About 73.5% of the initial adsorption capability is kept after eight adsorption–desorption cycles. The polypyrrole/chitosan nanocomposite monolith can be a promising candidate for the efficient removal of Cr(VI).     

交联壳聚糖季铵盐吸附剂的制备及其对重金属离子的吸附

以壳聚糖为原料、二甲基二烯丙基氯化铵（DMDAAC）为接枝单体、甲醛为预交联剂、环氧氯丙烷为交联剂,通过反相乳液聚合制备出交联壳聚糖季铵盐吸附剂,并将其用于吸附Ni（Ⅱ）和Cr（Ⅵ）。考察了吸附时间、溶液初始浓度、溶液pH等因素对吸附效果的影响。实验结果表明：该吸附剂对Ni（Ⅱ）和Cr（Ⅵ）的吸附过程遵循拟二级动力学方程,吸附等温线符合Langmuir方程;在30 ℃条件下,Ni（Ⅱ）和Cr（Ⅵ）的溶液初始浓度均为1 mmol/L时,该吸附剂吸附Ni（Ⅱ）和Cr（Ⅵ）的最佳溶液pH分别为7和6,对应的平衡吸附量分别为1.18,1.99 mmol/g;该吸附剂可用盐酸再生,重复使用性能良好。     

Smoldering Combustion (STAR) for the Treatment of Contaminated Soils: Examining Limitations and Defining Success

Smoldering combustion, commercially available as the Self‐sustaining Treatment for Active Remediation (STAR) technology, is an innovative technique that has shown promise for the remediation of contaminant source zones. Smoldering combustion is an exothermic reaction (net energy producing) converting carbon compounds and an oxidant (e.g., oxygen in air) to carbon dioxide, water, and energy. Thus, following ignition, the smoldering combustion reaction can continue in a self‐sustaining manner (i.e., no external energy or added fuel input following ignition) as the heat generated by the reacting contaminants is used to preheat and initiate combustion of contaminants in adjacent areas, propagating a combustion front through the contaminated zone provided a sufficient flux of air is supplied. The STAR technology has applicability across a wide‐range of hydrocarbons in a variety of hydrogeologic settings; however, there are limitations to its use. Impacted soils must be permeable enough to allow a sufficient flux of air to the combustion front and there exists a minimum required concentration of contaminants such that the soils contain sufficient fuel for the reaction to proceed in a self‐sustaining manner. Further limitations, as well as lessons learned and methods to mitigate these limitations, are presented through a series of case studies. In summary, the successful implementation of STAR will result in >99 percent reduction in contaminant concentrations in treated areas, limited residual contaminant mass, reduced groundwater contaminant mass flux which can be addressed through monitored natural attenuation; and an enhanced site exit strategy, reduced lifecycle costs, and reduced risk. ©2016 Wiley Periodicals, Inc.     

Removal of Cr(VI) Ions from Aqueous Solutions Using Poly 3-Methyl Thiophene Conducting Electroactive Polymers

This paper deals with a new application of poly 3-methyl thiophene synthesized chemically onto sawdust (termed as P3MTh/SD) as an effective adsorbent for removal of Cr(VI) ions from aqueous solutions using column system. Chemical synthesis of poly 3-methyl thiophene was performed by addition of ferric chloride (in chloroform) as oxidant to sawdust which had previously been soaked in monomer solution. All the sorption experiments were conducted using dynamic or column system at room temperature. The effect of important parameters such as pH and initial concentration on uptake of Cr(VI) was investigated. In order to find out the possibility of the regeneration and reuse of the exhausted adsorbent, desorption studies were also performed. The currently introduced adsorbent was found to be an efficient adsorbent for removal of highly toxic and hazardous Cr(VI) ions from aqueous solutions. As our breakthrough analysis has indicated, each gram of P3MTh/SD is able to remove more than 95% of Cr(VI)ions from 300 mL of Cr(VI) polluted solution with the initial concentration of 25 mg L⁻¹ in column system. Sorption/desorption of Cr(VI) ions was found to be a highly pH dependent processes.     

Insufficient source area remediation results in the rebound of TCE breakdown products in groundwater

In the early 1990s, a soil removal action was completed at a former disposal pit site located in southern Michigan. This action removed waste oil, cutting oil, and chlorinated solvents from the unsaturated zone. To contain groundwater contaminant migration at the site, a groundwater pump‐and‐treat system comprised of two extraction wells operating at a combined flow of 50 gallons per minute, carbon treatment, and a permitted effluent discharge was designed, installed, and operated for over 10 years. Groundwater monitoring for natural attenuation parameters and contaminant attenuation modeling demonstrated natural attenuation of the contaminant plume was adequate to attain site closure. As a result of incomplete contaminant source removal, a rebound of contaminants above the levels established in the remedial action plan (RAP) has occurred in the years following system shutdown and site closure. Groundwater concentrations have raised concerns regarding potential indoor air quality at adjacent residential properties constructed in the past 9 to 10 years. The only remedial option available in the original RAP is to resume groundwater pump‐and‐treat. To remediate the source area, an alternate remediation strategy using an ozone sparge system was developed. The ozone sparge remediation strategy addresses the residual saturated zone contaminants beneath the former disposal pit and reestablishes site closure requirements without resumption of the pump‐and‐treat system. A pilot study was completed successfully; and the final system design was subsequently approved by the Michigan Department of Environmental Quality. The system was installed and began operations in July 2010. As of the January 2011 monitoring event, the system has shown dramatic improvement in site contaminant concentrations. The system will continue to operate until monitoring results indicate that complete treatment has been obtained. The site will have achieved the RAP objectives when the system has been shut down and meets groundwater residential criteria for four consecutive quarters. © 2011 Wiley Periodicals, Inc.     

花生壳活性炭吸附溶液中的铀

以农林废弃物花生壳为原料、氢氧化钾为活化剂、微波为热源,制备了花生壳活性炭。以花生壳活性炭为吸附剂吸附溶液中的U(VI),考察了初始U(VI)质量浓度、活性炭加入量、溶液pH、吸附时间对U(VI)去除效果的影响。实验结果表明,在溶液中初始U(VI)质量浓度为30mg/L、活性炭加入量为0.5g/L、溶液pH为5.5、吸附时间为150min的较佳条件下,活性炭对U(VI)的吸附量为56.37mg/g,U(VI)去除率为93.94％。     

Synthesis of Ion-Imprinted Alginate Based Beads: Selective Adsorption Behavior of Nickel (II) Ions

Ni(II) imprinted and non-imprinted bioadsorbent alginate beads were prepared, and utilized in the selective adsorption of Ni(II) ions. The optimum adsorption capacity were 6.00 mmol g^?1 at 500 ppm initial metal ion concentration at pH 7 for Ni(II) imprinted alginate beads (IIP). The equilibrium data were applied to Langmuir and Freundlich adsorption isotherms, and it fitted both isotherm models. Thermodynamic parameters showed favorable and endothermic nature of adsorption. Ni(II) imprinted bead showed the strong ability to selective adsorption from Cu(II), Co(II) and Zn(II) ions. In conclusion, Ni(II) ion imprinted alginate beads could be used repeatedly without any significant reduce of adsorption capacity.     

Magnetic Cr(VI) Ion Imprinted Polymer for the Fast Selective Adsorption of Cr(VI) from Aqueous Solution

In this study, a novel magnetic Cr(VI) ion imprinted polymer (Cr(VI)-MIIP) was successfully synthesized and used as a selective sorbent for the adsorption of Cr(VI) ions from aqueous solution. It can be synthesized through the combination of an imprinting polymer and magnetic nanoparticles. The high selectivity achieved using MIIP is due to the specific recognition cavities for Cr(VI) ions created in Cr(VI)-MIIP. Also, the magnetic properties that could be obtained using magnetic nanoparticles, helps to separate adsorbent with an external magnetic field without either additional centrifugation or filtration procedures. The magnetic Fe₃O₄ nanoparticles (MNPs) were synthesized using an improved co-precipitation method and modified with tetraethylorthosilicate (TEOS) before imprinting. The magnetic Cr(VI) ion imprinted polymer was prepared through precipitation copolymerization of 4-vinylpyridine as the complexing monomer, 2-hydroxyethyl methacrylate as a co-monomer, the Cr⁶⁺ anion as a template, and ethylene glycol dimethacrylate (EGDMA) as a cross-linker in the presence of modified magnetite nanoparticles. This novel synthesized sorbent was characterized using different techniques. Batch adsorption experiments were performed to evaluate the adsorption conditions, selectivity, and reusability. The results showed that the maximum adsorption capacity was 39.3 mg g^?1, which was observed at pH 3 and at 25?°C. The equilibrium time was 20 min, and the amount of adsorbent which gave the maximum adsorption capacity was 1.7 g L^?1. Isotherm studies showed that the adsorption equilibrium data were fitted well with the Langmuir adsorption isotherm model and the theoretical maximum adsorption capacity was 44.86 mg g^?1. The selectivity studies indicated that the synthesized sorbent had a high single selectivity sorption for the Cr(VI) ions in the presence of competing ions. Thermodynamic studies revealed that the adsorption process was exothermic (\(\Delta H\)?<?0) and spontaneous (\(\Delta G\)?<?0). In addition, the spent MIIP can be regenerated up to five cycles without a significant decrease in adsorption capacity.     

A conceptual study on the bio-wall technology: Feasibility and process design

In-situ bioremediation is a process by which contaminants in subsurface environments are biologically eliminated or mineralized; however, it is often difficult to implement. Microbes sparsely distributed in deep soils are incapable of degrading a chemical rapidly; furthermore, fine-pore structures of soils tend to retard the penetration and propagation of these microbes and hinder oxygen transfer. The latter is particularly detrimental to the aerobic growth of microbes, which is often essential for bioremediation. Measures intended to promote bioremediation, such as the addition of surfactants for enhancing dissolution and the application of genetically engineered microbes for accelerating the biodegradation of contaminants, are almost impossible to adopt. This is attributable to the fact that various facets of the bioremediation process (e.g., the distribution of dissolved contaminants, nutrients, and oxygen, and the concentration of microbes) cannot be readily manipulated. This article proposes a novel technology, namely, bio-wall. This technology resorts to an in-situ constructed medium with porosity and organic content greater than those of the original soil for promoting the adsorption and retention of microbes and the biodegradation of contaminants. Moreover, oxygen and nutrients are supplied to the bio-wall to facilitate microbialgrowth. The results of conceptual design study and simulation have revealed that the technology is indeed feasible and, under certain environmental conditions, cost-effective. Particularly noteworthy is the fact that bio-wall can prevent contaminant migration through the enhancement of the biodegradation rate and reduction of the plume-distance, both by several orders of magnitude.     

Chloroethene dechlorination in acidic groundwater: Implications for combining fenton's treatment with natural attenuation

A sulfuric acid leak in 1988 at a chloroethene‐contaminated groundwater site at the Naval Air Station Pensacola has resulted in a long‐term record of the behavior of chloroethene contaminants at low pH and a unique opportunity to assess the potential impact of source area treatment technologies, which involve acidification of the groundwater environment (e.g., Fenton's‐based in situ chemical oxidation), on downgradient natural attenuation processes. The greater than 75 percent decrease in trichloroethene (TCE) concentrations and the shift in contaminant composition toward predominantly reduced daughter products (dichloroethene [DCE] and vinyl chloride [VC]) that were observed along a 30‐m groundwater flow path characterized by highly acidic conditions (pH = 3.5 ± 0.4) demonstrated that chloroethene reductive dechlorination can continue to be efficient under persistent acidic conditions. The detection of Dehalococcoides‐type bacteria within the sulfuric acid/chloroethene co‐contaminant plume was consistent with biotic chloroethene reductive dechlorination. Microcosm studies conducted with ¹⁴C‐TCE and ¹⁴C‐VC confirmed biotic reductive dechlorination in sediment collected from within the sulfuric acid/chloroethene co‐contaminant plume. Microcosms prepared with sediment from two other locations within the acid plume, however, demonstrated only a limited mineralization to ¹⁴CO₂ and ¹⁴CO, which was attributed to abiotic degradation because no significant differences were observed between experimental and autoclaved control treatments. These results indicated that biotic and abiotic mechanisms contributed to chloroethene attenuation in the acid plume at NAS Pensacola and that remediation techniques involving acidification of the groundwater environment (e.g., Fenton's‐based source area treatment) do not necessarily preclude efficient chloroethene degradation. © 2007 Wiley Periodicals, Inc.     

The Hidden Potential of Mass‐based Treatment: A Method for Preventing Rebound

A major challenge for in situ treatment is rebound. Rebound is the return of contaminant concentrations to near original levels following treatment, and frequently occurs because much of the residual nonaqueous phase liquid (NAPL) trapped within the soil capillaries or rock fractures remains unreachable by conventional in situ treatment. Fine‐textured strata have an especially strong capacity to absorb and retain contaminants. Through matrix diffusion, the contaminants dissolve back into groundwater and return with concentrations that can approach pretreatment levels. The residual NAPL then serves as a continuing source of contamination that may persist for decades or longer. A 0.73‐acre (0.3‐hectare) site in New York City housed a manufacturer of roofing materials for approximately 60 years. Coal tar served as waterproofing material in the manufacturing process and releases left behind residual NAPL in soils. An estimated 47,000 pounds (21,360 kg) of residual coal tar NAPL contaminated soils and groundwater. The soils contained strata composed of sands, silty sands, and silty clay. A single treatment using the RemMetrik^® process and Pressure Pulse Technology^® (PPT) targeted the contaminant mass and delivered alkaline‐activated sodium persulfate to the NAPL at the pore‐scale level via in situ treatment. Posttreatment soil sampling demonstrated contaminant mass reductions over 90 percent. Reductions in posttreatment median groundwater concentrations ranged from 49 percent for toluene to 92 percent for xylenes. Benzene decreased by 87 percent, ethylbenzene by 90 percent, naphthalene by 80 percent, and total BTEX by 91 percent. Mass flux analysis three years following treatment shows sustained reductions in BTEX and naphthalene, and no rebound. ©2015 Wiley Periodicals, Inc.     

Re‐evaluation of treatment approach for a site contaminated with Freon‐113 and 1,1,1‐trichloroethane

This study demonstrates a remedial approach for completing the remediation of an aquifer contaminated with 1,1,2‐trichlorotrifluoroethane (Freon‐113) and 1,1,1‐trichloroethane (TCA). In 1987, approximately 13,000 pounds of Freon‐113 were spilled from a tank at an industrial facility located in the state of New York. The groundwater remediation program consisted of an extraction system coupled with airstripping followed by natural attenuation of residual contaminants. In the first phase, five recovery wells and an airstripping tower were operational from April 1993 to August 1999. During this time period over 10,000 pounds of CFC‐13 and 200 pounds of TCA were removed from the groundwater and the contaminant concentrations decreased by several orders of magnitude. However, the efficiency of the remediation system to recover residual Freon and/or TCA reduced significantly. This was evidenced by: (1) low levels (< 10 ppb) of Freon and TCA captured in the extraction wells and (2) a slight increase of Freon and/or TCA in off‐site monitoring wells. A detailed study was conducted to evaluate the alternative for the second‐phase remediation. Results of a two‐year groundwater monitoring program indicated the contaminant plume to be stable with no significant increase or decrease in contaminant concentrations. Monitored geochemical parameters suggest that biodegradation does not influence the fate and transport of these contaminants, but other mechanisms of natural attenuation (primarily sorption and dilution) appear to control the fate and transport of these contaminants. The contaminants appear to be bound to the soil matrix (silty and clay units) with limited desorption as indicated by the solid phase analyses of contaminant concentrations. Results of fate and transport modeling indicated that contaminant concentrations would not exceed the action levels in the wells that showed a slight increase in contaminant concentrations and in the downgradient wells (sentinel) during the modeled timeframe of 30 years. This feasibility study for natural attenuation led to the termination of the extraction system and a transaction of the property, resulting in a significant financial benefit for the original site owner. © 2003 Wiley Periodicals, Inc.     

Utilisation of Supernatants of Pure Cultures of Streptomyces thermocarboxydus NH50 to Reduce Chromium Toxicity and Mobility in Contaminated Soils

Chromium is a heavy metal used in various industrial sectors. Improper handling and storage of chromium-laden effluents or wastes can lead to the pollution of the environment. The most toxic form is the more mobile one: hexavalent chromium Cr(VI). The reduction of Cr(VI) results in the immobilisation of chromium into its less toxic trivalent form Cr(III). This phenomenon may prevent the contamination of groundwater when the soil in the vadose zone is contaminated. Many bacteria have been isolated from contaminated soils and described to reduce Cr(VI) into Cr(III). A new Cr(VI)-reducing strain, identified as a Streptomyces thermocarboxydus,has been isolated and studied in our laboratories for its ability to reduce Cr(VI). This aerobic bacterium, in contrast to other genera described which mediate reduction via enzymes, produces reducing agents into the culture supernatants. Cr(VI) reduction by these substances is accelerated by the presence of small concentration of cupric ions (Cu²⁺). The reducing agent(s) can be easily recovered from the bacterial cultures and used as cell-free solution to treat contaminated soils by an in situ or ex situ processes.