Persistent organochlorine residues in fish and water birds from the Biobio river,Chile

Concentrations of polychlorinated biphenyls (PCBs), DDT and its metabolites, HCH isomers and hexachlorobenzene (HCB) were determined in fish and birds from different locations in the Biobio river basin (central Chile). Samples collected near the mouth of the river contained high concentrations of PCBs, reflecting the massive use of these xenobiotics in the urban and industrial areas of Concepcion and Talcauano. Samples collected in the central part of the basin contained very high concentrations of lindane that coincide with the widespread use of lindane-based pesticides (purified -HCH) in this area. DDT was distributed homogeneously throughout the basin, except at Laguna Icalma, the source of the river in the Andes. Most PCB residues in fish and birds consisted of congeners between penta- and hepta-chlorobiphenyls. In fish, the predominant congeners were the pentachlorobiphenyl 23445 (IUPAC number 118) and the hexachlorobiphenyl 2234455 (PCB-153); in birds 224455 (PCB-180) prevailed.     

An evaluation of benthic macroinvertebrate biomass methodology

This study shows that biological assessments of water quality status using biomass estimates of wet, dry, and ash-free dry weights and counts of individual organisms from a small, headwater stream in southwestern Ohio provide essentially similar results concerning the impact of a sewage treatment plant discharge. Of the indices of biotic status for the stream segment employed for data evaluation; Diversity Index (D), Community Diversity Index (d), Trophic Condition Index (TCI), and Empirical Biotic Index (EBI), the latter two provided evaluations most consistent with benchmark water chemistry and physics information concerning the trophic status of the stream. In addition, the percent composition of macro-invertebrate taxa by pollutional category; clean water, facultative, and pollution tolerant, as ascribed using TCI and EBI ranges for individual taxa collected in combination of Ekman grab, rock-filled basket sampler and drift net samples, proves adequate for interpretation of biotic status.     

A Metamodeling Approach for Integrated Assessment of Air Quality Policies

A method is proposed to build integrated models (also called Metamodels) aimed at quantifying the economic efficiency of air quality policies. This Metamodeling approach is based on the coupling of two complementary models, that operate at different scales in space and time, and which represent the economic and the physical and chemical processes, respectively. The joint consideration of the physico-chemical and techno-economic structure of the pollution control problems permits a comprehensive evaluation of air pollution abatement strategies. The motivating pollution control problems include urban-regional air quality management through efficient energy and traffic control policies. A pilot study, exploiting data collected in the Geneva canton (Switzerland), is used to demonstrate the potential of the approach.     

Respiratory Suspended Particulate (RSP) Concentration and its Implications to Roadside Workers: A Case Study of Hong Kong

The adsorption behaviour of Diphenylamine (DPAM), napthylamine ( NAM), napthylamine ( NAM)and aniline on pyrolusite and activated carbon has been studied.Pyrolusite shows remarkable sorption capacity for DPAM and NAM as compared to aniline; (the adsorption followed theorder:Activated Carbon: DPAM = NAM > AnilinePyrolusite: DPAM: NAM > NAM> Aniline)The maximum adsorption of NAM occurred in theconcentration range 4–20 g mL^-1 on pyrolusite (95%)and 4–50 g mL^-1 on activated carbon (100%). Theeffect of various doses of activated carbon on the adsorption of NAM confirm Langmuir and Freundlich isotherms where asFreundlich isotherm is obeyed by pyrolusite. The adsorption of NAM on both the absorbents is not affected in presence ofDPAM over a wide range of their initial concentrations (20–60g mL^-1). The desorption studies of NAM onpyrolusite was carried out by batch as well as column processes.Excellent results were obtained when a mixture of n-hexane andisopropanol (91:1) was used as eluent.     

Exposure estimates in assessing helath effects of air pollution

Air pollution has been associated with adverse health effects. Difficulties in interpreting studies of health effects of exposure to air pollution arise in estimating exposure. Until recently, studies of effects of air pollution have relied on pollution exposure measurements obtained from fixed location air pollution stations monitoring outside air (to evaluate compliance with air quality standards, rather than to examine population exposure). However, recent evidence suggests that there are substantial differences between air pollution levels measured at such sites and levels to which people are actually exposed, i.e. personal exposure. The present study examines effects of ambient urban air pollution on persons suffering from asthma, healthy non-asthmatic subjects and school children (in 2 Canadian cities, Toronto and Hamilton). Air pollution exposure is being assessed by data obtained from: (1) conventional abatement oriented fixed location air pollution monitoring stations, (2) an extensive population oriented network, (3) inside and (4) outside structures (homes and schools) as well as (5) personal air pollution samplers. The data indicate variability in these different estimates of exposure which have implications on health effects assessment.     

Application of remote sensing to exposure monitoring

Although exposure assessments cannot be completed remotely, remote sensing techniques provide an invaluable adjunct in exposure monitoring programs. Exposure can be defined as the summation over time, in all media, of the amount of a pollutant available at the exchange boundaries of the receptor during a specified period. This paper describes a few remote monitoring techniques that provide direct measurement input into an exposure assessment and several that furnish quantitative or qualitative information leading to decisions regarding how to monitor, such that the source-exposure-dose relationships can be fully defined. Two general classes of remote sensing systems are included in this discussion-passive and active. Passive systems depend on a measurement of the energy reflected or emitted by a target and active systems use an energy source, e.g., a laser to perform the environmental interrogation. Airborne as well as ground-based remote monitoring measurements or systems are also considered in this paper.     

Monitoring of the functioning of ecosystems

The theoretical basis, the content and the possible applications of the program Monitoring of ecosystems are considered. A functional definition of ecosystem is proposed, and some features of ecosystems are defined on this basis. The program Monitoring of ecosystems is visualized as a large-scale program of simple measurements of the rates of the main ecosystem processes. The expected results can be utilized in two ways: (1) a comparative knowledge of ecosystem functioning provides the fundamentals of geography of ecosystems, and (2) the constant, repeatable evaluation of a given ecosystem function provides a basis for its rational management.     

Sampling to differentiate between pulse and press perturbations

There is great inconsistency in the use of the terms pulse and press when describing types of perturbations. This is due primarily to a failure to distinguish between the cause and the effect of the perturbation in question. The cause and effect may be either short- or long-term and clearly one may be short-term and the other long-term. Distinction between these two types of disturbance is crucial for management to prevent further impact. Thus, it is important to describe separately these two aspects of a perturbation. Here, we define a protocol for sampling perturbations which enables the cause and effect to be distinguished between short- or long-term. Existing (i.e., already established) assemblages and newly-established assemblages are sampled and compared among disturbed and control locations. Existing assemblages may have been affected by past (pulse) disturbances and/or ongoing (press) disturbances, whereas the establishment of new assemblages can only be influenced by ongoing disturbances. We describe the procedures for assessing impacts of estuarine marinas as an illustration of the issues to be considered in any habitat. Settlement plates and defaunated sediment are suggested for sampling the establishment of new assemblages in aquatic environments.     

Polychlorinated biphenyls, organochlorine pesticides and chlorobenzenes content of livers from Atlantic cod (Gadus morhua) caught off Halifax Nova Scotia

The mean levels ± s.d., (ranges) of organochlorines, pesticides, chlorobenzenes and polychlorinated biphenyl were determined in the livers of 100 Atlantic cod (Gadus morhua) caught off the east coast of Canada in 1980 and were as follows: PCB 1.71±0.90 (0.24–4.33); p,p-DDE 0.28±0.15 (0.01–0.84); p,p-DDD 0.10±0.09 (trace-0.84); p,p-DDT 0.15±0.09 (ND-0.58); -HCH 0.06±0.02 (trace-0.10); -HCH (ND-trace); heptachlor 0.02±0.01 (ND-0.04); heptachlor epoxide 0.15±0.37 (ND-2.16); dieldrin 0.06±0.11 (ND-0.71); hexachlorobenzene 0.02±0.01 (trace-0.05) mg kg^–1 (wet wt.). The levels of these compounds in 1980 have not changed over the previous eight years with the exception of PCB and the DDT group where there appears to be a general decline between 1972 and 1975 with no significant change thereafter.     

Monitoring the condition of the Canadian forest environment: The relevance of the concept of ‘ecological indicators’

The Canadian forest environment is characterized by high spatial and temporal variability, especially in the west. Our forests vary according to climate, landform, and surficial geology, and according to the type, intensity, extent of, and the time since the last disturbance. Most Canadian forests have had a history of repeated acute, episodic disturbance from fire, insects, wind, diseases and/or logging, with a frequency of disturbance varying from a few decades to many centuries. These sources of variability have resulted in a complex and continually changing mosaic of forest conditions and stages of successional development.Monitoring the quality of this dynamic forested landscape mosaic is extremely difficult, and in most cases the concept of a relatively simple index of forest ecosystem quality or condition (i.e. an ecological indicator) is probably inappropriate. Such ecological indicators are better suited for monitoring chronic anthropogenically induced disturbances that are continuous in their effect (e.g. acid rain, heavy metal pollution, air pollution, and the greenhouse effect) in ecosystems that, in the absence of such chronic disturbance, exhibit very slow directional change (e.g. lakes, higher order streams and rivers). Monitoring the effects of a chronic anthropogenic disturbance to forest ecosystems to determine if it is resulting in a sustained, directional alteration of environmental quality will require a definition of the expected pattern of episodic disturbance and recovery therefrom (i.e. patterns of secondary succession in the absence of the chronic disturbance). Only when we have such a temporal fingerprint of forest ecosystem condition for normal patterns of disturbance and recovery can we determine if the ecosystem condition is being degraded by chronic human-induced alteration of the environment. Thus, degradation is assessed in terms of deviations from the expected temporal pattern of conditions rather than in terms of an instantaneous assessment of any particular condition. The concept of ecological rotation (the time for a given ecosystem to recover from a given disturbance back to some defined successional condition) is useful in the definition of these temporal fingerprints. This requires information on the intensity of disturbance, the frequency of disturbance, and the rate of successional recovery. Only when all three of these are known or estimated can statements be made as to whether the ecosystem is in a longterm sustainable condition or not.The somewhat overwhelming complexity of this task has led forest ecologists to use ecosystem-level computer simulation models. Appropriately structured and calibrated models of this type can provide predictions of the overall temporal patterns of ecosystem structure and functions that can be expected to accompany a given frequency and character of episodic disturbance. Such models can also be used to examine the long-term consequences of chronic disturbances such as acid rain and climatic change. Predictive ecosystem-level models should be used in conjunction with some method of stratifying the inherent spatial biophysical variability of the forest environment, such as the biogeoclimatic classification system of British Columbia.     

Monitoring the biotic aspects of our environment as a policy instrument

As all environmental programs also programs monitoring the biotic aspects of our environment (dealt with in this article) should contribute to a more effective and efficient environmental policy. These programs have to function therefore (as no other type of environmental information does, according to the authors) as cheap and efficient early warning and early control systems, providing decision makers with important and reliable monitoring results.How these monitoring programs should function in the decision making process is illustrated in abstract in this article by a simple control system with feedback (as shown in Figures 1, 2 and 3).The monitoring programs dealt with in this article should enable us to detect and forecast changes in the most important biotic aspects of our environment and-by continuous monitoring-to control whether the use of policy instruments has been effective or not in averting or diminishing unwanted changes (problems).Two options of decision makers with respect to monitoring results are shown (either to disregard unwanted changes as a problem or to accept these changes as a problem and to do something about them). To contribute to an effective and efficient environmental policy monitoring results therefore have to be important and reliable enough to react upon.The question is raised which biotic aspects in our environment are (or have to be considered as) important (because of their own value, as indicators and/or as biotic conditions) and how reliable monitoring results can (have to) be obtained.It is discussed how environmentalists could try to make it more difficult for decision makers to duck the problems (by monitoring only important aspects and by using only perfectly clear targets and standards) and how they could try at the same time to make it easier for them to take action (by setting up integrated environmental monitoring programs in order to find out how desired and undesired changes can be influenced). The role of active publicity is stressed in this connection.     

Application of CFD Methods for Modelling in Air Pollution Problems: Possibilities and Gaps

Different urban air pollution problems deal with complex structure of air flows and turbulence. For such problems the Computer Fluid Dynamics (CFD) methods become widely used. However, this approach despite a number of advantages has some problems. Experience of use of CFD tools for development of models and suggestions of their applications for a local scale air pollution over a complex terrain and stable stratification are discussed in this paper, including: Topography and complex geometry: choose of the co-ordinate system and computer grid; Turbulence closure for air pollution modelling: modified k- model for stable stratified ABL; Boundary conditions for vertical profiles of velocity for stable-stratified atmosphere; Effects of the radiation and thermal budget of inclined surfaces to dispersion of pollutants; Artificial sources of air dynamics and circulation.Some examples of CFD applications for air pollution modelling for a flat terrain, mountainous area, mining open cast and indoor ventilation are discussed. Modified k- model for stably-stratified ABL is suggested. Due to the isotropic character of the k- model a combination of it in vertical with the sub-grid turbulence closure in horizontal can be more suitable for ABL. An effective scheme of boundary conditions for velocity profiles, based on the developed similarity theory for stable-stratified ABL, is suggested. Alongside with the common studies of atmospheric dispersion, the CFD methods have also demonstrated a good potential for studying anthropogenic and artificial-ventilation sources of air dynamic and circulation in local-scale processes of air pollution.     

A FRAMEWORK FOR THE ULTIMATE ENVIRONMENTAL INDEX – Putting Atmospheric Change Into Context With Sustainability

Assessing the major atmospheric issues – acidic deposition, climatechange, ozone depletion, smog, hazardous airpollutants and suspended particulate matter – together rather than individually provides many advantages. But to be successful, this integration requires a common method for relating theseissues to one another. This is a scientific question.In order to successfully resolve the atmospheric issues (a policy question) requires communication of the relevant science to non-scientists in plain language. Non-scientists need to be part of the development of the structure of the communications vehicle. The objective for multi-issueassessment, and thus for the development of an index to trackthe state of the environment in an integrated way, is of courserelated to the desire to achieve environmentally sustainable development.Sustainability can be represented by a 3-legged stool and is an aptsymbol of the struggle of Canadians to balance their ecological,economic and social needs. Although the environment is the basisof all life, humankind has created society and has defined how thatsociety will function (the economy). The three legs of the stool(ecosystem, economy, society) represent the three parts of thesustainability balance. The seat of the stool represents thegovernance process and the three legs are deeply embedded in thisgovernance process because it is the governance which ensures thestability of the system over time. The challenge then is to measure the stability of the stool in a waywhich all can understand. This measure of sustainability must respondto individual and collective actions which improve or degrade the environment. This paper presents such a framework for a sustainability index andoutlines the next steps that need to be taken.The framework starts from the premise that ecosystem, economy andsociety are equal parts of sustainability. Ecosystem indices arerepresentative measures of the state of the environment while economicindices are representative measures of the state of the economy. Socialindices in some way have to measure the state of society. The trick,for a successful sustainability index, will be to ensure that the importantaspects of the ecosystem, the economy and society, are included. The overall index must berelatively stable but must be responsive to changes.     

Establishing a standard Sonoran Reference Plant and its application in monitoring industrial and urban pollution throughout the Sonoran Desert

Using analyses from honey mesquite (Prosopis glandulosa) leaves from nearly pristine locations in Arizona, an inorganic plant concentration standard is proposed for use as a Sonoran Reference Plant (SRP). Such a standard can be used as a monitoring device for different anthropogenic pollution sources throughout the Sonoran Desert. To test the application of the SRP, honey mesquite leaves were collected at different sites in southern Arizona and their chemical fingerprints compared to SRP. Sources of element origin were identified through factor analysis and correlation matrices. A terrestrial factor was found in leaves from all sites. Anthropogenic factors varied for different sites. Mesquite leaves accumulated significant amounts of elements originating from copper smelters (As, Sb) and urban pollution (La, Sm, Ce, V). These pollutants are small-sized and have been linked to human lung diseases. Mesquite is a deciduous tree; the yearly comparison of mesquite leaf element concentration spectra to the SRP standard can be used to determine seasonal improvement or deterioration of environmental quality in a particular area.     

Soil-Water Partitioning and Desorption Hysteresis of Volatile Organic Compounds from a Louisiana Superfund Site Soil

The adsorption and desorption of three volatile organic compounds (1,2- dichloroethane, 1,1,2- trichloroethane and 1,1,2,2-tetrachloroethane) from a previously uncontaminated clayey soil sample from a Superfund site in North Baton Rouge,Louisiana was studied. In the linear range of the adsorption isotherm, the partition constants were not affected by the presence of the co-solutes. The adsorption isotherms over a wide concentration range on the soil followed the nonlinearFreundlich isotherm. The desorption of the compounds showedsignificant hysteresis at all concentrations studied. Approximately 20 to 70% of the adsorbed mass of organic compounds resisted the desorption even after five months ofsuccessive desorption steps. The desorption of four compounds(1,2-dichloroethane, 1,1,2-trichloroethane, 1,4-dichlorobenzeneand hexachlorobutadiene) from a contaminated soil sample fromthe same site was also studied. The aqueous concentration declined as the successive desorption steps progressed. For hexachlorobutediene the desorption can be visualized as occurring in two stages. The first stage involved a loosely bound or reversible fraction and the second stage involveda tightly bound or resistant fraction.     

Insecticide Contamination of Jamaican Environment. V. Island-Wide Rapid Survey of Residues in Surface and Ground Water

Residues of organochlorines and organophosphates were determined by gas chromatography in water and sediment from 26 locations in 17 major rivers, 7 natural springs and 13 wells across Jamaica. Samples were collected on only one occasion between May and July, 1994. Residues of endosulfan were detected in all but three rivers; -endosulfan in 15 samples of sediment (0.9–108.1, mean = 28.93, S.E. = 7.198 g kg-1) and 13 of water (0.01–0.35, mean = 0.11, S.E. = 0.035 g L-1), -endosulfan in 5 sediment (15.29–49.35, mean = 30.56, S.E. = 7.132 g kg-1) and 12 water (0.05–0.31, mean = 0.14, S.E. = 0.031 g L-1) samples, and endosulfan sulphate in waters of three rivers (0.003–0.244 g L-1). Chlorpyrifos was present in 9 sediment (0.423-135.2, mean = 18.38, S.E. = 10.699 g kg-1) and two water (0.001–0.022 g L-1) samples, diazinon and ethoprophos in the sediment of one river each. Mean levels (g L-1) of and isomers and sulphate of endosulfan were 0.16 (S.E. = 0.057), 0.12 (S.E. = 0.036) and 0.15 (S.E. = 0.089), respectively, in four of the seven springs and 0.23 (S.E. = 0.052), 0.11 (S.E. = 0.029) and 0.26 (S.E. = 0.088), respectively, in seven of the thirteen wells monitored.     

Determination of Endosulfans in Soil/Sediment Samples from Point Mugu, Oxnard, California Using Capillary Gas Chromatography/Mass Selective Detection (GC/MSD)

The extent of contamination by endosulfans in soil samples collected from the Point Mugu watershed near Oxnard, California was determined using capillary gas chromatography/mass selective detection (GC/MSD). The study was designed to detect three organochlorinated pesticides: endosulfan , endosulfan and endosulfan sulfate. Thirteen sets of two soil samples each were taken from various sites in the region. Our results show that the endosulfan levels in these soils range from trace amounts to nearly 30 ppm, with endosulfan being the most abundant and endosulfan sulfate the least. Two sites of the study, Hueneme and Revolon and Farm and Revolon, showed high amounts of endosulfans and , with concentrations between 20 and 30 ppm. The majority of the other sites studied in this research produced concentrations of less than 10 ppm for each of the three endosulfans monitored. At five areas in particular, Pleasant Valley and Creek, Laguna and Creek, Etting and Creek, Road and Creek and Hueneme and Creek, less than 2 ppm or only trace amounts of endosulfans , and sulfate were detected.     

Comparative Studies on the Usefulness of Seven Ecological Indices for the Marine Coastal Monitoring Close to the Shore on the Swedish East Coast

The simultaneous behaviour of seven ecological indices(Hurlberts, Margalefs, Menhinicks, Shannons,species number, Jaccards and saprobic index) wasstudied based on phytoplankton data close to the shoreon the East coast of Sweden during the summer 1998.The sampling stations had a similar eutrophicationlevel and were located in bays. Standard phytoplanktondatabases were used in calculating the indices, whichwere later compared using cluster analysis.Hurlberts, Margalefs, Menhinicks, Shannons andspecies number indices, as measure of communitydiversity, produced similar trends which oftendiffered from those based on Jaccards index ofsimilarity. However, the simultaneous use of theseindices was found meaningful as a possible part of themonitoring close to the shore. The application of asaprobic index lead to erroneous conclusions in thestudied case.     

Thermal impact evaluation for brunner Island steam electric station: Toward a more realistic assessment

A realistic approach to thermal impact assessment is presented which employs a two-dimensional thermal plume model, a large data base for river flow and temperature, and accounts for nonuniform spatial distribution of habitats and seasonal differences in fish behavior. The end result portrays real effects of the thermal impact rather than an artificially constructed worst-case scenario.     

Field Study of Wind and Traffic to Test a Street Canyon Pollution Model

In the U.K., local authorities have new duties to review and assess air quality. Dispersion models are important tools in this process. The performance of a street canyon model, AEOLIUS, in calculating carbon monoxide (CO) concentrations in urban areas is discussed. A field experiment was conducted in a busy street canyon in Leek, Staffordshire. Wind speed and direction were measured at three heights adjacent to the street. The canyon's CO concentrations and traffic counts were recorded. Predicted concentrations of CO, calculated using AEOLIUS, were compared with the observed values. The concept of a roof-top wind is discussed, as are the consequences of using wind measurements from outside the town. Choice of wind measurement location and height of the anemometer above the canyon had a pronounced effect on calculating the roof-top wind. Two methods of deriving a street level wind speed from a roof-top wind speed gave results that differ by up to a factor of two. AEOLIUS had variable skill at predicting CO concentrations depending on the roof-top wind direction: possible reasons for this variability are explored. A sensitivity study of the model showed that vehicle emissions have the greatest impact on predicted concentrations. Implications for local air quality management are discussed.