Rapid hydropyrolysis of model compounds for epoxy resin oligomers and biomass tar

The rapid hydropyrolysis of model compounds for epoxy resin oligomers and biomass tar was carried out in a hydrogen atmosphere at 1073 K and 973 K. The assumed oligomers were partially pyrolyzed epoxy resin with biomass tar as solvent for the resin. The product distributions obtained from rapid hydropyrolysis of phenol and bisphenol-A are shown. We also discuss the effects of reaction temperature and hydrogen partial pressure on the product yield. In particular, more phenol was produced from bisphenol-A at 973 K than at 1073 K. The yield of methane, which was the final hydropyrolysis product, increased with increasing hydrogen partial pressure, whereas benzene and phenol were believed to behave as intermediate products in the hydropyrolysis reaction. The results suggest that phenol could be obtained with high selectivity from tar by optimizing the reaction conditions.     

Methods for determining the biomass content of waste.

As CO2 emission trading in Europe has been established it is of essential importance to distinguish between biogenic and fossil emissions. Emissions resulting from bio-fuels and biogenous fractions are categorized as climate-neutral. Determination of plants using only fossil or bio-fuels is simple but categorization becomes more difficult for plants using a mix of fossil and bio-fuel such as solid recovered fuels. In the meantime, different methods for solving this problem have been developed. Using different approaches and technologies, all of these methods have the same goal: determining the biomass content (biogenic fraction), for example, in solid recovered fuels or in the off-gas of a mono- or co-incineration plant in order to calculate the biogenic carbon dioxide emissions. In the following article, the most common methods for determining the biogenic fraction of fuels, namely the Selective Dissolution Method, the Balance Method and the 14C-Method will be explained in detail.     

A model for estimation of potential generation of waste electrical and electronic equipment in Brazil

Sales of electrical and electronic equipment are increasing dramatically in developing countries. Usually, there are no reliable data about quantities of the waste generated. A new law for solid waste management was enacted in Brazil in 2010, and the infrastructure to treat this waste must be planned, considering the volumes of the different types of electrical and electronic equipment generated.This paper reviews the literature regarding estimation of waste electrical and electronic equipment (WEEE), focusing on developing countries, particularly in Latin America. It briefly describes the current WEEE system in Brazil and presents an updated estimate of generation of WEEE. Considering the limited available data in Brazil, a model for WEEE generation estimation is proposed in which different methods are used for mature and non-mature market products.The results showed that the most important variable is the equipment lifetime, which requires a thorough understanding of consumer behavior to estimate. Since Brazil is a rapidly expanding market, the “boom” in waste generation is still to come. In the near future, better data will provide more reliable estimation of waste generation and a clearer interpretation of the lifetime variable throughout the years.     

Studies on the pyrolysis behavior of gasification and melting systems for municipal solid waste

 It is important to investigate the pyrolysis processes of municipal solid waste (MSW) in the same way as for any mixture comprised of multiple substances. In this article, a two-reaction model for a variety of MSW mixtures is proposed to predict mass changes due to pyrolysis. In order to formulate the model based on pyrolysis kinetics, we conducted experiments to determine the kinetic model parameters. By thermal analysis of the typical components of MSW, mass changes attributable to the pyrolysis reaction were found at about 350°C for paper, 400°–500°C for plastics, and 200°–400°C for garbage (dry condition). Activation energies were obtained by the Ozawa method based on the mass changes in pyrolysis. Thus, the pyrolysis behavior is formulated as a function of temperature. Then the pyrolysis mass change of the mixture can be predicted by using a weighted sum of the individual components. The model proved useful in experiments with real waste (refuse-derived fuels). Furthermore, the weight yields (pyrolysis gas, tars, solid residues) of the mixture can be calculated by their additive property after measuring the mass balance of each component. Received: May 11, 2001 / Accepted: November 16, 2001     

Sample preparation and biomass determination of SRF model mixture using cryogenic milling and the adapted balance method

The biogenic fraction of a simple solid recovered fuel (SRF) mixture (80 wt% printer paper/20 wt% high density polyethylene) is analyzed with the in-house developed adapted balance method (aBM). This fairly new approach is a combination of combustion elemental analysis (CHNS) and a data reconciliation algorithm based on successive linearisation for evaluation of the analysis results. This method shows a great potential as an alternative way to determine the biomass content in SRF. However, the employed analytical technique (CHNS elemental analysis) restricts the probed sample mass to low amounts in the range of a few hundred milligrams. This requires sample comminution to small grain sizes (<200 μm) to generate representative SRF specimen. This is not easily accomplished for certain material mixtures (e.g. SRF with rubber content) by conventional means of sample size reduction.This paper presents a proof of principle investigation of the sample preparation and analysis of an SRF model mixture with the use of cryogenic impact milling (final sample comminution) and the adapted balance method (determination of biomass content). The so derived sample preparation methodology (cutting mills and cryogenic impact milling) shows a better performance in accuracy and precision for the determination of the biomass content than one solely based on cutting mills. The results for the determination of the biogenic fraction are within 1–5% of the data obtained by the reference methods, selective dissolution method (SDM) and ¹⁴C-method (¹⁴C-M).     

GIS-based modelling for the estimation of municipal solid waste generation and collection

In the present paper, an innovative model for the estimation of municipal solid waste generation and collection is proposed. This model is part of an extended solid waste management system and uses a spatial Geodatabase, integrated in a GIS environment. It takes into consideration several parameters of waste generation, such as population density, commercial activities, road characteristics and their influence on the location and allocation of waste bins. Ground-based analysis was applied for the estimation of the inter-relations between the aforementioned factors and the variations in waste generation between residential and commercial areas. Therefore, the proposed model follows a unified categorization approach for residential and commercial activities and focuses on the dominant factors that determine waste generation in the area under study. The most important result of the research work presented in the current paper is an accurate estimation of the optimal number of waste bins and their allocation. A new methodology and an appropriate algorithm have been developed for this purpose in order to facilitate routing and waste collection. By using these results, municipalities aware of social, economical and environmental factors, related to waste management, can achieve optimal usage of their resources and offer the best possible services to their citizens.     

Increase of Ozone Concentration in an Inland Basin During the Period of Nocturnal Thermal High

Since ground level ozone concentrations in the basin on one day before the occurrence of unusually high air temperature with nocturnal thermal high showed a typical urban type of a maximum ozone concentration at 1300 LST and a minimum at night. However, a maximum ozone concentration under extremely high air temperature of 39.2 °C was detected at 1700 LST or 1800 LST at two environmental monitoring sites, which was 4 or 5 hr delayed from the typical occurrence time, 1300 LST. Its maximum value showed about 50 or 70% increase of the concentration more than the typical maximum value and its concentration gradually decreased until 2100 LST. After 1200 LST until 1800 LST, air temperature was maintained over 35 °C and the high temperature made a great contribution to the increase of O₃ for several hours. The deviated occurrence time of a maximum ozone concentration is mainly attributed to meteorological and topographic effects – shifted occurrence time of maximum air temperature, shrunken atmospheric boundary layer depth and wind. While daytime O₃ concentration due to photochemical production of O₃ from NO₂ increased, NO₂ concentration decreased, with their reverse respondent patterns each night. A secondary maximum concentration of O₃ at 2300 LST or 2400 LST is due to a much shallower depth of nocturnal surface inversion layer with daytime producing more O₃ than that of the daytime convective boundary layer, resulting in the increase of ozone concentration, though the reduction of ozone occurred under the reversal process of O₃ into NO₂.     

A preliminary investigation into the physical and chemical properties of biomass ashes used as aggregate fillers for bituminous mixtures

Fly and bottom ashes are the main by-products arising from the combustion of solid biomass. Since the production of energy from this source is increasing, the processing and disposal of the resulting ashes has become an environmental and economic issue. Such ashes are of interest as a construction material because they are composed of very fine particles similar to fillers normally employed in bituminous and cementitious mixtures. This research investigates the potential use of ash from biomass as filler in bituminous mixtures. The morphological, physical and chemical characteristics of 21 different ashes and two traditional fillers (calcium carbonate and “recovered” plant filler) were evaluated and discussed. Leaching tests, performed in order to quantify the release of pollutants, revealed that five ashes do not comply with the Italian environmental re-use limits. Experimental results show a wide range of values for almost all the investigated properties and a low correlation with biomass type in terms of origin and chemical composition. Furthermore, sieving and milling processes were found to improve the properties of the raw material in terms of grading and sample porosity. The effectiveness of these treatments and the low content of organic matter and harmful fines suggest that most of the biomass ashes investigated may be regarded as potential replacements for natural filler in bituminous mixtures.     

Hydrothermal treatment and characterization of model food garbage,focusing on the effect of additional foreign matter on internal temperature,pressure and products

Hydrothermal treatment of model food garbage focusing on the effects of additional foreign matter has been performed in subcritical conditions as a pretreatment for the next step, i.e., the bio-processing and production of liquid feed or fertilizer. Using the hydrothermal technique, we studied the temporal change in internal temperature and pressure in a reactor on the elapsed heating time to check the equipment safety in terms of temperature and pressure. The gaseous and water-soluble liquid was also characterized to investigate the feasibility of retrieving valuable chemicals and emitting environmentally hazardous substances. From the changes in the internal temperature and pressure curve, the maximum temperature and pressure were 196 °C and 1.42 MPa for 30-min elapsed heating time, which was below the predefined temperature limits of 200 °C and pressure of 1.55 MPa. No such irregular behavior was observed in the temperature and pressure curve except that it was a little different for the foreign matter detergent, which also was within the limits. The qualitative and quantitative analysis of end products showed that the emitted malodorous substances and chemicals were further below the threshold levels for Japan.     

A mathematical model for the anaerobic treatment of Baker's yeast effluents

Baker's yeast fermentation produces high strength wastewaters containing high concentrations of organic materials that cannot easily be degraded by biological processes. A two-stage (anaerobic-aerobic) treatment system has been used in order to treat this effluent efficiently. Most of the COD reduction takes place during the anaerobic degradation. The objective of this study was to generate a simple mathematical model for the anaerobic stage. The model, which is based on the elimination of COD, assumes that only three consecutive reactions namely hydrolysis, acidogenesis and methanogenesis are significant. In the laboratory-scale experiments, feed strength was increased from 3600 to 14,000 mg O2 l-1 in a batch reactor. Three reaction rate constants were found as 0.08, 0.004, 0.06 h-1 by analyzing data from the laboratory experiments. The model was tested and found to be congruent with the daily operation data, which were collected from the Pakmaya Baker's Yeast Kocaeli Factory Plant. This plant contains three Upflow Anaerobic Sludge Blanket reactors, which are run in series. The rate constants of the hydrolysis and methanogenesis were similar to the batch experiment case.     

A model for evaluating the social performance of construction waste management

It has been determined by existing literature that a lot of research efforts have been made to the economic performance of construction waste management (CWM), but less attention is paid to investigation of the social performance of CWM. This study therefore attempts to develop a model for quantitatively evaluating the social performance of CWM by using a system dynamics (SD) approach. Firstly, major variables affecting the social performance of CWM are identified and a holistic system for assessing the social performance of CWM is formulated in line with feedback relationships underlying these variables. The developed system is then converted into a SD model through the software iThink. An empirical case study is finally conducted to demonstrate application of the model. Results of model validation indicate that the model is robust and reasonable to reflect the situation of the real system under study. Findings of the case study offer helpful insights into effectively promoting the social performance of CWM of the project investigated. Furthermore, the model exhibits great potential to function as an experimental platform for dynamically evaluating effects of management measures on improving the social performance of CWM of construction projects.     

Application of the dynamic model of Saeman to an industrial rotary kiln incinerator: Numerical and experimental results

In order to simulate granular materials structure in a rotary kiln under the steady-state regime, a mathematical model has been developed by Saeman (1951). This model enables the calculation of the bed profiles, the axial velocity and solids flow rate along the kiln. This model can be coupled with a thermochemical model, in the case of a reacting moving bed. This dynamic model was used to calculate the bed profile for an industrial size kiln and the model projections were validated by measurements in a 4 m diameter by 16 m long industrial rotary kiln. The effect of rotation speed under solids bed profile and the effect of the feed rate under filling degree were established. On the basis of the calculations and the experimental results a phenomenological relation for the residence time estimation was proposed for the rotary kiln.     

Utilization of amorphous rice husk ash for the synthesis of ZSM-5 zeolite under low temperature

The present study deals with the production and characterization of ZSM-5 zeolite under low temperature using amorphous rice husk ash as an alternative cheap silica source. Rice husk was combusted at various temperatures for the production of amorphous silica. The resulted amorphous silica ash was then utilized without any other treatment as a starting material for the synthesis of ZSM-5 zeolite using low temperature and under atmospheric pressure. For comparison, the high-temperature synthetic approach, the hydrothermal treatment under high temperature and autogenous pressure with the autoclave process, was also applied for the synthesis of ZSM-5 zeolite. The low-temperature method led successfully to the synthesis of highly siliceous zeolite of type ZSM-5. The produced materials were characterized using a variety of analytical techniques, including X-ray diffraction, Fourier transformation infrared spectroscopy, thermogravimetry–differential thermogravimetry analyses, scanning electron microscopy, electron dispersion X-ray analysis and nitrogen porosimetry. The results show that the utilization of an industrial by-product in abundance as a starting material can lead through a simple inexpensive technique to the synthesis of a high value added microporous material with many potential applications.     

Development of a model for the evaluation of compost supply–demand dynamics: theory and case study in an area of Rabat region,Morocco

Journal of Material Cycles and Waste Management - Compost Supply–Demand (CSD) dynamics is one of the important aspects to consider when assessing composting plants’ sustainability....     

High solids co-digestion of food and landscape waste and the potential for ammonia toxicity

A pilot-scale study was completed to determine the feasibility of high-solids anaerobic digestion (HSAD) of a mixture of food and landscape wastes at a university in central Pennsylvania (USA). HSAD was stable at low loadings (2 g COD/L-day), but developed inhibitory ammonia concentrations at high loadings (15 g COD/L-day). At low loadings, methane yields were 232 L CH₄/kg COD fed and 229 L CH₄/kg VS fed, and at high loadings yields were 211 L CH₄/kg COD fed and 272 L CH₄/kg VS fed. Based on characterization and biodegradability studies, food waste appears to be a good candidate for HSAD at low organic loading rates; however, the development of ammonia inhibition at high loading rates suggests that the C:N ratio is too low for use as a single substrate. The relatively low biodegradability of landscape waste as reported herein made it an unsuitable substrate to increase the C:N ratio. Codigestion of food waste with a substrate high in bioavailable carbon is recommended to increase the C:N ratio sufficiently to allow HSAD at loading rates of 15 g COD/L-day.     

MSW stabilization in an anaerobic bioreactor landfill and evaluation of in-situ leachate treatment potential with the help of quadric model

Journal of Material Cycles and Waste Management - Recirculation of the leachate using bioreactor technology for in-situ treatment of leachate is an efficient method for reducing the contaminants...     

A computer simulation model for fleet sizing for the marine division of the New York City department of sanitation

The Marine Division of the New York City Department of Sanitation (DOS) operates a fleet of tugboats and barges for the transport of refuse from New York City to Fresh Kills Landfill on Staten Island. In the early 1980s, DOS was faced with a situation whereby many of its barges were aged and decrepit, yet workload was scheduled to increase as another major landfill was shut down. With major barge investment decisions on the horizon, DOS commissioned the development of the Barge Operations Systems Simulator (BOSS), for assistance in the task of fleet sizing. This paper reports on the development and use of the BOSS model.     

Behaviour of Rice-Byproducts and Optimizing the Conditions for Production of High Performance Natural Fiber Polymer Composites

This present study deals with evaluating some available rice by-products, such as rice straw and rice husks, as a fiber component in manufacturing of high performance natural fiber polymer composites (NFPC). The utilization of these undesirable wastes will contribute to the reduction of the environmental impact of waste disposal by burning. Two matrices (thermoset and thermoplastic) were used. Optimization of manufacture conditions of polyester-based thermosetting polymer composites was carried out through examine the effects of fibers to polymer ratio, amounts of catalyzed and initiator, fraction size of fibers and substituting one fibers by another, as well as time, temperature and pressure of pressing. The possibility of styrene containing polyester solution on improving the fiber interface via in situ grafting and enhancing the strength and water resistance of the produced NFPC was also evaluated, in comparison with that produced from using thermoplastic matrix (polypropylene) in presence of coupling agent. The production of this valuable product (NFPC) by this simple procedure, which not needs special devices (twin extrusion with heater), and chemicals to improve the compatibility between fibers and polymer matrix, will ensure reasonable profits and direct impacts on the Egyptian economy in general and rice growers in particular.