Heat of absorption of CO2 in aqueous ammonia and ammonium carbonate/carbamate solutions

A reaction calorimeter was used to determine the enthalpies of absorption of CO₂ in aqueous ammonia and in aqueous solutions of ammonium carbonate at temperatures of 35–80 °C. The heat of absorption of CO₂ with 2.5 wt% aqueous ammonia solution was found to be about 70 kJ/mol CO₂, which is lower than that with MEA (around 85 kJ/mol) at 35 and 40 °C. The value decreases with increased loading, but not to as low a value as expected by the carbonate–bicarbonate reaction (26.88 kJ/mol). The enthalpy of absorption of CO₂ in aqueous ammonia at 60 and 80 °C decreases with loadings at first, then increases between 0.2 mol CO₂/mol NH₃ and 0.6 mol CO₂/mol NH₃, and then decreases again. The behavior of the heat of absorption of CO₂ in 10 wt% ammonium carbonate solution was found to be the same as that of aqueous ammonia at loadings above 0.6 mol CO₂/mol NH₃. The heat of absorption increases with increasing temperature. The heats of absorption are directly related to the extent of the various reactions with CO₂ and can be assessed from the species variation in the liquid phase.     

Investigation of amine amino acid salts for carbon dioxide absorption

The carbon dioxide capture potential of amine amino acid salts (AAAS), formed by mixing equinormal amounts of amino acids; e.g. glycine, β-alanine and sarcosine, with an organic base; 3-(methylamino)propylamine (MAPA), was assessed by comparison with monoethanolamine (MEA), and with amino acid salt (AAS) from amino acid neutralized with an inorganic base; potassium hydroxide (KOH). Carbon dioxide absorption and desorption experiments were carried out on the solvent systems at 40 °C and 80 °C respectively. Experimental results showed that amine amino acid salts have similar CO₂ absorption properties to MEA of the same concentration. They also showed good signs of stability during the experiments. Amino acid salt from an inorganic base, KOH, showed lower performance in CO₂ absorption than the amine amino acid salts (AAAS) mainly due to a lower equilibrium temperature sensitivity. AAAS showed better performance than MEA of same concentration. AAAS from neutralization of sarcosine with MAPA showed the best performance and the performance could be further enhanced when promoted with excess MAPA. The solvent comparison is semi-quantitative since the bubble structure, and thus gas–liquid interfacial area may not be the same for all experiments, however superficial gas velocities were kept constant.     

Post-combustion CO2-capture from coal-fired power plants: Preliminary evaluation of an integrated chemical absorption process with piperazine-promoted potassium carbonate

The simulation tool ASPEN Plus^® is used to model the full CO₂-capture process for chemical absorption of CO₂ by piperazine-promoted potassium carbonate (K₂CO₃/PZ) and the subsequent CO₂-compression train. Sensitivity analysis of lean loading, desorber pressure and CO₂-capture rate are performed for various solvent compositions to evaluate the optimal process parameters. EbsilonProfessional^® is used to model a 600 MW_el (gross) hard coal-fired power plant. Numerical equations for power losses due to steam extraction for solvent regeneration are derived from simulation runs. The results of the simulation campaigns are used to find the process parameters that show the lowest specific power loss. Subsequently, absorber and desorber columns are dimensioned to evaluate investment costs for these main components of the CO₂-capture process. Regeneration heat duty, net efficiency losses and column investment costs are then compared to the reference case of CO₂-capture by monoethanolamine (MEA).CO₂-capture by piperazine-promoted potassium carbonate with subsequent CO₂-compression to 110 bar shows energetic advantages over the reference process which uses MEA. Additionally, investment costs for the main components in the CO₂-capture process (absorber and desorber columns) are lower due to the enhanced reaction kinetics of the investigated K₂CO₃/PZ solvent which leads to smaller component sizes.     

CO2 capture from power plants: Part II. A parametric study of the economical performance based on mono-ethanolamine

While the demand for reduction in CO₂ emission is increasing, the cost of the CO₂ capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in the future. In this paper, a definition of the economic baseline for post-combustion CO₂ capture from 600 MW_e bituminous coal-fired power plant is described. The baseline capture process is based on 30% (by weight) aqueous solution of monoethanolamine (MEA). A process model has been developed previously using the Aspen Plus simulation programme where the baseline CO₂-removal has been chosen to be 90%. The results from the process modelling have provided the required input data to the economic modelling. Depending on the baseline technical and economical results, an economical parameter study for a CO₂ capture process based on absorption/desorption with MEA solutions was performed.Major capture cost reductions can be realized by optimizing the lean solvent loading, the amine solvent concentration, as well as the stripper operating pressure. A minimum CO₂ avoided cost of € 33 tonne⁻¹ CO₂ was found for a lean solvent loading of 0.3 mol CO₂/mol MEA, using a 40 wt.% MEA solution and a stripper operating pressure of 210 kPa. At these conditions 3.0 GJ/tonne CO₂ of thermal energy was used for the solvent regeneration. This translates to a € 22 MWh⁻¹ increase in the cost of electricity, compared to € 31.4 MWh⁻¹ for the power plant without capture.     

CO2 capture from power plants: Part I. A parametric study of the technical performance based on monoethanolamine

Capture and storage of CO₂ from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO₂ capture process from flue gas of a 600 MWe bituminous coal fired power plant, based on absorption/desorption process with MEA solutions, using ASPEN Plus with the RADFRAC subroutine, was performed. This optimization aimed to reduce the energy requirement for solvent regeneration, by investigating the effects of CO₂ removal percentage, MEA concentration, lean solvent loading, stripper operating pressure and lean solvent temperature.Major energy savings can be realized by optimizing the lean solvent loading, the amine solvent concentration as well as the stripper operating pressure. A minimum thermal energy requirement was found at a lean MEA loading of 0.3, using a 40 wt.% MEA solution and a stripper operating pressure of 210 kPa, resulting in a thermal energy requirement of 3.0 GJ/ton CO₂, which is 23% lower than the base case of 3.9 GJ/ton CO₂. Although the solvent process conditions might not be realisable for MEA due to constraints imposed by corrosion and solvent degradation, the results show that a parametric study will point towards possibilities for process optimisation.     

Modeling CO2 capture with aqueous monoethanolamine

Hilliard completed several thermodynamic models in Aspen Plus^® for modeling CO₂ removal with amine solvents, including MEA–H₂O–CO₂. This solvent was selected to make a system model for CO₂ removal by absorption/stripping. Both the absorber and the stripper used RateSep? to rigorously calculate mass transfer rates. The accuracy of the new model was assessed using a recent pilot plant run with 35 wt.% (9 m) MEA. Absorber loading and removal were predicted within 6%, and the temperature profile was approached within 5 °C. An average 3.8% difference between measured and calculated values was achieved in the stripper. A three-stage flash configuration which efficiently utilizes solar energy was developed. It reduces energy use by 6% relative to a simple stripper. Intercooling was used to reach 90% removal in the absorber at these optimized conditions.     

Ionic liquids for post-combustion CO2 absorption

The present work is a study to evaluate ionic liquids as a potential solvent for post-combustion CO₂ capture. In order to enhance the absorption performance of a CO₂ capture unit, different ionic liquids have been designed and tested. The main goal was to get a comparison between a reference liquid and selected ionic liquids. As the reference, a solution of 30 w% monoethanolamine (MEA) and water was used. A large range of different pure and diluted ionic liquids was tested with a special screening process to gain general information about the CO₂ absorption performance. Based on these results, a 60 w% ionic liquid solution in water was selected and the vapour–liquid equilibrium was measured experimentally between 40 °C and 110 °C. From these curves the enthalpy of absorption for capturing CO₂ into the ionic liquid was determined. With these important parameters one is able to calculate the total energy demand for stripping of CO₂ from the loaded solvent for comparison of the ionic liquid based solvent with the reference MEA solvent. The energy demand of this 60 w% ionic liquid is slightly lower than that of the reference solution, resulting in possible energy savings between 12 and 16%.     

Experimental measurement and modeling of the rate of absorption of carbon dioxide by aqueous ammonia

In this work, the rate of absorption of carbon dioxide by aqueous ammonia solvent has been studied by applying a newly built wetted wall column. The absorption rate in aqueous ammonia was measured at temperatures from 279 to 304 K for 1 to 10 wt% aqueous ammonia with loadings varying from 0 to 0.8 mol CO₂/mol NH₃. The absorption rate in 30 wt% aqueous mono-ethanolamine (MEA) was measured at 294 and 314 K with loadings varying from 0 to 0.4 as comparison.It was found that at 304 K, the rate of absorption of carbon dioxide by 10 wt% NH₃ solvent was comparable to the rates for 30 wt% MEA at 294 and 314 K (a typical absorption temperature for this process). The absorption rate using ammonia was however significantly lower at temperatures of 294 K and lower as applied in the Chilled Ammonia Process. However, at these low temperatures, the rate of absorption in ammonia has only a small temperature dependency.The rate of absorption decreases strongly with decreasing ammonia concentrations and increasing CO₂ loadings.The rate of absorption of carbon dioxide by aqueous ammonia solvent was modeled using the measurements of the unloaded solutions and the zwitter-ion mechanism. The model could successfully predict the experimental measurements of the absorption rate of CO₂ in loaded ammonia solutions.     

Carbon dioxide capture with concentrated,aqueous piperazine

Concentrated, aqueous piperazine (PZ) has been investigated as a novel amine solvent for carbon dioxide (CO₂) absorption. The CO₂ absorption rate of aqueous PZ is more than double that of 7 m MEA and the amine volatility at 40 °C ranges from 11 to 21 ppm. Thermal degradation is negligible in concentrated, aqueous PZ up to a temperature of 150 °C, a significant advantage over MEA systems. Oxidation of concentrated, aqueous PZ is appreciable in the presence of copper (4 mM), but negligible in the presence of chromium (0.6 mM), nickel (0.25 mM), iron (0.25 mM), and vanadium (0.1 mM). Initial system modeling suggests that 8 m PZ will use 10–20% less energy than 7 m MEA. The fast mass transfer and low degradation rates suggest that concentrated, aqueous PZ has the potential to be a preferred solvent for CO₂ capture.     

Comparative study of the heats of absorption of post-combustion CO2 absorbents

Heats of absorption of CO₂ with different solvents were measured in this work in a commercially available reaction calorimeter CPA-122 (Chemisens AS, Sweden) as function of temperature, loading and solvent composition over the temperature range from 40 to 120 °C. Studied amines include primary amines (monoethanolamine and 2-amino-2-methyl-1-propanol), tertiary amines (N-methyldiethanolamine and N,N-diethylethanolamine), diamines (1-(2-aminoethyl)-aminoethanol and N-methyl-1,3-propanediamine), triamine (diethylenetriamine), and cyclic amine (piperazine). Combinations of these amines and also mixtures of potassium carbonate and piperazine were tested. Experimental heats of absorption of CO₂ with these systems are compared.     

Kinetics of sulfur dioxide- and oxygen-induced degradation of aqueous monoethanolamine solution during CO2 absorption from power plant flue gas streams

Studies of the kinetics of sulfur dioxide (SO₂)- and oxygen (O₂)-induced degradation of aqueous monoethanolamine (MEA) during the absorption of carbon dioxide (CO₂) from flue gases derived from coal- or natural gas-fired power plants were conducted as a function of temperature and the liquid phase concentrations of MEA, O₂, SO₂ and CO₂. The kinetic data were based on the initial rate which shows the propensity for amine degradation and obtained under a range of conditions typical of the CO₂ absorption process (3–7 kmol/m³ MEA, 6% O₂, 0–196 ppm SO₂, 0–0.55 CO₂ loading, and 328–393 K temperature). The results showed that an increase in temperature and the concentrations of MEA, O₂ and SO₂ resulted in a higher MEA degradation rate. An increase in CO₂ concentration gave the opposite effect. A semi-empirical model based on the initial rate, ?r_MEA = {6.74 × 10⁹ e^?(29,403/RT)[MEA]^0.02([O]^2.91 + [SO₂]^3.52)}/{1 + 1.18[CO₂]^0.18} was developed to fit the experimental data. With the higher order of reaction, SO₂ has a higher propensity to cause MEA to degrade than O₂. Unlike previous models, this model shows an improvement in that any of the parameters (i.e. O₂, SO₂, and CO₂) can be removed without affecting the usability of the model.     

Calcium oxide for CO2 capture: Operational window and efficiency penalty in sorption-enhanced steam methane reforming

Calcium oxide (CaO) is a material that is being widely investigated in the context of CO₂ capture. One such application is as a CO₂ sorbent in the sorption-enhanced steam methane reforming processes (SERP). CO₂ is captured in an adsorption mode, where the conversion of CH₄ to H₂ is also enhanced, and released later in a separate desorption mode. This work presents an analysis of the relation between different process conditions and parameters during both adsorption and desorption modes. The interrelation between these conditions and the sorbent properties as well as the targeted carbon capture ratio is analysed. Conditions relevant for capturing 85% of carbon in the feed on CaO are determined and interlinked. A steam-to-carbon ratio of 4.2 has been determined to be relevant under 600 °C and 17 bar adsorption conditions. Similarly, process conditions relevant for regenerating the sorbent are determined and interlinked. For purge steam-to-CO₂ ratio of 1.8 at a desorption pressure of 1 bar, relevant desorption temperature has been calculated to be 820 °C. System simulations under these adsorption and desorption conditions resulted in a system efficiency of 50.8%. Effect of tuning process operating conditions on system efficiency as well as the efficiency penalty associated with the regeneration of the sorbent are investigated by process simulations using Aspen Plus^®. Possible system heat integration routes to reduce the efficiency penalty are proposed and the results of the process simulations are presented.     

Carbonic anhydrase-facilitated CO2 absorption with polyacrylamide buffering bead capture

A novel CO₂ separation concept is described wherein the enzyme carbonic anhydrase (CA) is used to increase the overall rate of CO₂ absorption after which hydrated CO₂ reacts with regenerable amine-bearing polyacrylamide buffering beads (PABB). Following saturation of the material's immobilized tertiary amines, CA-bearing carrier water is separated and recycled to the absorption stage while CO₂-loaded material is thermally regenerated. Process application of this concept would involve operation of two or more columns in parallel with thermal regeneration with low-pressure steam taking place after the capacity of a column of amine-bearing polymeric material was exceeded. PABB CO₂-bearing capacity was evaluated by thermogravimetric analysis (TGA) for beads of three acrylamido buffering monomer ingredient concentrations: 0 mol/kg bead, 0.857 mol/kg bead, and 2 mol/kg bead. TGA results demonstrate that CO₂-bearing capacity increases with increasing PABB buffering concentration and that up to 78% of the theoretical CO₂-bearing capacity was realized in prepared PABB samples (0.857 mol/kg recipe). The highest observed CO₂-bearing capacity of PABB was 1.37 mol of CO₂ per kg dry bead. TGA was also used to assess the regenerability of CO₂-loaded PABB. Preliminary results suggest that CO₂ is partially driven from PABB samples at temperatures as low as 55 °C, with complete regeneration occurring at 100 °C. Other physical characteristics of PABB are discussed. In addition, the effectiveness of bovine carbonic anhydrase for the catalysis of CO₂ dissolution is evaluated. Potential benefits and drawbacks of the proposed process are discussed.     

Numerical parametric study on CO2 capture by indirect thermal swing adsorption

Post-combustion CO₂ capture remains one of the most-challenging issue to lower CO₂ emissions of existing power plants or heavy industry installations because of strong economy and energy efficiency aspects. The major issue comes from CO₂ dilution (4% for NGCC and 14% for PC) and the high flow rates to be treated. Furthermore, CO₂ purity has to be higher than 95% with recovery at 90%, to match the transportation/injection requirements.The MEA absorption process remains the reference today but its energy consumption (about 3 MJ/kg_CO2) and the amine consumption are still challenging drawbacks.The interest of CO₂ capture by indirect TSA (Temperature Swing Adsorption) was demonstrated experimentally in a previous work. The aim of this paper is to present the results of a numerical parametric study. Two main parameters are explored: the desorption temperature (100–200 °C) and the purge flow rate (0.1–0.5 Ndm³ min⁻¹). Four performance indicators are evaluated: CO₂ purity, recovery, productivity and specific energy consumption.Results show that purity above 95% can be achieved. Keeping the 95% target, it is possible to achieve recovery at 81% with productivity at 57.7 g_CO2/kg_ads h and a specific energy consumption of 3.23 MJ/kg_CO2, which is less than for the reference MEA process.Comparison with other adsorption processes exhibits that this process has good potential especially since some improvements are still expected from further research.     

Corrosion and polarization behavior of carbon steel in MEA-based CO2 capture process

This work reveals levels of corrosion rate and polarization behavior of carbon steel immersed in aqueous solutions of monoethanolamine (MEA) used in the absorption-based carbon dioxide (CO₂) capture process for greenhouse gas reduction from industrial flue gas streams. Such information was obtained from electrochemical-based corrosion experiments under a wide range of the CO₂ capture process conditions. The corrosion of carbon steel was evaluated in respect to process parameters including partial pressure of oxygen (O₂), CO₂ loading in solution, solution velocity, solution temperature, MEA concentration and metal surface condition. Results show that the aqueous MEA solution containing CO₂ provides a favorable condition for the corrosion of carbon steel to proceed. Corrosion rate is increased by all tested process parameters. These parametric effects were explained by the electrochemical kinetic data obtained from polarization curves and by the thermodynamic data obtained from Pourbaix diagram.     

CO2 removal using membrane gas absorption

The objective of this study is to investigate the potential process for the removal of carbon dioxide (CO₂) from flue gas using fundamental membrane contactor, which is a membrane gas absorption (MGA) system. The experiments consisted of microporous polyvinylidenefluoride (PVDF) flat sheet membrane with 0.1 μm (as module I) and 0.45 μm (as module II) pore size. 2-Amino-2-methyl-1-propanol (AMP) solution was employed as the liquid absorbent. The effect of AMP concentration was studied with variation in the range 1–5 M. In addition, the experiments were carried out with 10%, 20%, 30% and 40% gas ratio of CO₂ to N₂ and pure CO₂ as well. Through contact angle measurement, membranes for module I and module II were obtained with CA values of around 130.25° and 127.77°, respectively. The mass transfer coefficients for module II are lower than those of module I for 1–5 M of AMP. Furthermore, the increase in CO₂ concentration in the feed gas stream enhanced the CO₂ flux as the driving force of the system was increased in sequence from 1 M to 5 M of AMP. However, after the particular percentage (40%) of CO₂ inlet concentration, the CO₂ fluxes seem saturated. The combination of AMP as liquid absorbent and PVDF microporous membrane in MGA system has shown the potential to remove the CO₂ from flue gas. In addition, the higher AMP concentration gave higher mass transfer coefficient at low liquid flow rates.     

Techno-Economic Study of CO2 Capture from an Existing Cement Plant Using MEA Scrubbing

Carbon dioxide is the major greenhouse gas responsible for global warming. Man-made CO₂ emissions contribute approximately 63% of greenhouse gases and the cement industry is responsible for approximately 5% of CO₂ emissions emitting nearly 900 kg of CO₂ per 1000 kg of cement. CO₂ from a cement plant was captured and purified to 98% using the monoethanolamine (MEA) based absorption process. The capture cost was $51 per tonne of CO₂ captured, representing approximately 90% of total cost. Steam was the main operating cost representing 39% of the total capture cost. Switching from coal to natural gas reduces CO₂ emissions by about 18%. At normal load, about 36 MW of waste heat is available for recovery to satisfy the parasitic heat requirements of MEA process; however, it is very difficult to recover.     

Comparison of several packings for CO2 chemical absorption in a packed column

CO₂ capture and storage has gained widespread attention as an option for reducing greenhouse gas emissions. Chemical absorption and stripping of CO₂ with hot potassium carbonate (K₂CO₃) solutions has been used in the past, however potassium carbonate solutions have a low CO₂ absorption efficiency. Various techniques can be used to improve the absorption efficiency of this system with one option being the addition of promoters to the solvent and another option being an improvement in the mass transfer efficiency of the equipment. This study has focused on improving the efficiency of the packed column by replacing traditional packings with newer types of packing which have been shown to have enhanced mass transfer performance. Three different packings (Super Mini Rings (SMRs), Pall Rings and Mellapak) have been studied under atmospheric conditions in a laboratory scale column for CO₂ absorption using a 30 wt% K₂CO₃ solution. It was found that SMR packing resulted in a mass transfer coefficient approximately 20% and 30% higher than that of Mellapak and Pall Rings, respectively. Therefore, the height of packed column with SMR packing would be substantially lower than with Pall Rings or Mellapak. Meanwhile, the pressure drop using SMR was comparable to other packings while the gas flooding velocity was higher when the liquid load was above 25 kg m⁻² s⁻¹. Correlations for predicting flooding gas velocities and pressure drop were fitted to the experimental data, allowing the relevant parameters to be estimated for use in later design.     

A 13C NMR investigation of CO2 absorption and desorption in aqueous 2,2′-iminodiethanol and N-methyl-2,2′-iminodiethanol

The carbon dioxide capture and release from aqueous 2,2′-iminodiethanol (DEA) and N-methyl-2,2′-iminodiethanol (MDEA) have been investigated by means of ¹³C NMR spectroscopy. We have designed two experimental procedures using a gas mixture containing 12% (v/v) CO₂ in N₂ or air and 0.667 M aqueous solutions of DEA and MDEA. To understand the CO₂–amine reaction equilibria, separate experiments of CO₂ absorption (at 293, 313 and 333 K) and desorption (at boiling temperature, room pressure) were carried out. The ¹³C NMR analysis has allowed us to establish: (1) the percentage of CO₂ stored in solution as HCO₃^?, CO₃^2? and DEA carbamate; (2) the formation of DEA carbamate as a function of absorption temperature and time; (3) the slower decomposition of DEA carbamate than that of bicarbonate. In the experiments planned to test the reuse of the regenerated amines, the absorbent solution was continuously circulated in a closed cycle while it was absorbing CO₂ in the absorber (set at 293 K) and simultaneously regenerating amine in the desorber (set at 388 K). After the equilibrium has been reached (13 h), the CO₂ absorption efficiency is comprised between 84.0% (DEA) and 82.6% (MDEA) and the average amine regeneration efficiency ranges between 69.6% (DEA) and 78.2% (MDEA). Additionally, MDEA is more stable towards thermal degradation than DEA.     

Structure and activity relationships for amine based CO2 absorbents—I

A study to determine the structure and activity relationships of various amine based CO₂ absorbents was performed in which, the absorption of pure CO₂ at atmospheric pressure was measured to assess the total absorption rate and capacities. Results showed that an increase in chain length between the amine and different functional groups in the absorbent structure, result in a decrease of absorption rate whereas, the absorption capacity was increased in most absorbents.