Removal of cyanobacterial blooms in Taihu Lake using local soils. II. Effective removal of Microcystis aeruginosa using local soils and sediments modified by chitosan

After sepiolite was modified with Fe3+ to increase its surface charge, the initial algal removal rate increased significantly, but its Q8h was not improved substantially at clay loadings below 0.1 g/L. Modification on netting and bridging properties of clays by either chitosan or polyacrylamide (PAM) dramatically increased flocculation (Q8h) of MA cells in freshwaters. Algal removal efficiencies of different solids, including Type III clays, local soils and sediments, were all improved to a similar level of >90% at a total loading of 0.011 g/L (contained 0.001 g/L chitosan) after they were modified with chitosan, making the idea of clearing up algal blooms using local soils/sediments possible. The mechanism of netting and bridging was confirmed to be the most important factor in improving the removal efficiency of cells, whereas clays also played important roles in the sedimentation of the floc.     

The enhancement of TiO2 photocatalytic activity by hydrogen thermal treatment

In this study, conventional TiO2 powder was heated in hydrogen (H2) gas at a high temperature as pretreatment. The photoactivity of the treated TiO2 samples was evaluated in the photodegradation of sulfosalicylic acid (SSA) in aqueous suspension. The experimental results demonstrated that the photodegradation rates of SSA were significantly enhanced by using the H2-treated TiO2 catalysts and an optimum temperature for the H2 treatment was found to be of 500-600 degrees C. The in situ electron paramagnetic resonance (EPR) signal intensity of oxygen vacancies (OV) and trivalent titanium (Ti3+) associated with the photocatalytic activity was studied. The results proved the presence of OV and Ti3+ in the lattice of the H2-treated TiO2 and indicated that both were contributed to the enhancement of photocatalytic activity. Moreover, the experimental results presented that the EPR signal intensity of OV and Ti3+ in the H2-treated TiO2 samples after 10 months storage was still significant higher than that in the untreated TiO2 catalyst. The experiment also demonstrated that the significant enhancement occurred in the photodegradation of phenol using the H2-treated TiO2.     

Effect of dissolved metal ions on PCE decomposition by gamma-rays

This study investigates the effect of initial tetrachloroethylene (PCE) concentration, irradiation dose and dissolved metal ions such as Cr3+, Mn2+, Fe3+, Co2+, Ni2+, Cu2+ and Zn2+ on removal of PCE by gamma irradiation. The amount of removed PCE decreased with increase in initial PCE concentration and increased with increase in irradiation dose. PCE removal reached a maximum in the presence of Fe3+, while Cu2+ strongly hindered PCE decomposition. Except for Cu2+, the amount of removed PCE in the presence of metal ions was linearly dependent on the standard reduction potential of the metal ions. The extraordinary inhibition of Cu2+ in PCE removal was caused by the action of Cu2+ as a strong *OH scavenger, that was directly confirmed by electron paramagnetic resonance spectroscopy.     

Removal of cyanobacterial blooms in Taihu Lake using local soils. I. Equilibrium and kinetic screening on the flocculation of Microcystis aeruginosa using commercially available clays and minerals

Algal removal abilities of 26 clays/minerals were classified into three categories according to the 8-h equilibrium removal efficiency (Q8h) and removal rate at a clay loading of 0.7 g/L. Type I clays (sepiolite, talc, ferric oxide, and kaolinite) had a Q8h > 90%, a t50 (time needed to remove 50% of the algae) < 15 min, and a t80 < 2.5 h. Type II clays (6 clays) had a Q8h 50-90%, a t50 < 2.5 h, and a t80 > 2.5 h. Type III clays (14 clays) with Q8h < 50%, t50 > 8 h and t80 > 14 h had no practical value in removal of algal blooms. When the clay loading was reduced to 0.2 g/L, Q8h for all the 25 materials decreased to below 60%, except for sepiolite whose Q8h remained about 97%. The high efficiency for sepiolite to flocculate M. aeruginosa cells in freshwaters was due to the mechanism of netting and bridging effect.     

Decomposition of organochlorine compounds in flue gas from municipal solid waste incinerators using natural and activated acid clays

High-temperature particle control (HTPC) using a ceramic filter is a dust collection method without inefficient cooling and reheating of flue gas treatment; thus, its use is expected to improve the energy recovery efficiency of municipal solid waste incinerators (MSWIs). However, there are concerns regarding de novo synthesis and a decrease in the adsorptive removal efficiency of dioxins (DXNs) at approximately 300°C. In this study, the effect of natural and activated acid clays on the decomposition of monochlorobenzene (MCB), one of the organochlorine compounds in MSW flue gas, was investigated. From the results of MCB removal tests at 30–300°C, the clays were classified as adsorption, decomposition, and low removal types. More than half of the clays (four kinds of natural acid clays and two kinds of activated acid clays) were of the decomposition type. In addition, the presence of Cl atoms detached from MCB was confirmed by washing the clay used in the MCB removal test at 300°C. Activated acid clay was expected to have high dechlorination performance because of its proton-rich-composition, but only two clays were classed as decomposition type. Conversely, all the natural acid clays used in this work were of the decomposition type, which contained relatively higher di- and trivalent metal oxides such as Al₂O₃, Fe₂O₃, MgO, and CaO. These metal oxides might contribute to the catalytic dechlorination of MCB at 300°C. Therefore, natural and activated acid clays can be used as alternatives for activated carbon at 300°C to remove organochloride compounds such as DXNs. Their utilization is expected to mitigate the latent risks related to the adoption of HTPC, and also to contribute to the improvement of energy recovery efficiency of MSWI.

ImplicationsThe effect of natural and activated acid clays on MCB decomposition was investigated to evaluate their suitability as materials for the removal of organochlorine compounds, such as DXNs, from MSWI flue gas at approximately 300°C. More than half of the clays used in this study showed the decomposition characteristics of MCB. The presence of Cl atoms in the clay used in the MCB removal test at 300°C proved the occurrence of MCB decomposition. The results of this study suggest a novel flue gas treatment method to establish high-energy efficient MSWI systems.     

Enhanced Fenton's destruction of non-aqueous phase perchloroethylene in soil systems

The Fenton's system is applied to the destruction of perchloroethylene (PCE) present as a dense non-aqueous phase liquid (DNAPL) in soil slurry systems; the initial concentration of PCE was 45 times higher than its aqueous solubility. Studies were conducted in two matrices: Ottawa sand and soil from Warsaw, IN. In Ottawa sand, a 60-62% decrease in PCE concentration was observed, and Cl(-) recovery was 47-58%, whereas in Warsaw soil, a 44-49% decrease in PCE concentration and a Cl(-) recovery of 40-42% were observed after the addition of 600 mM H(2)O(2) and 10 mM dissolved iron. Significantly enhanced destruction resulted during application of N-(2-hydroxyethyl) iminodiacetic acid (HEIDA) to Warsaw soil. For example, in the absence of HEIDA in Warsaw soil, 36% PCE loss and 33% Cl(-) release were observed at 600 mM H(2)O(2) and 5 mM Fe(III), while 74% PCE loss and 63% Cl(-) release were achieved at 600 mM H(2)O(2) and 5 mM Fe(III)-HEIDA. For both soils, the catalytic activities of Fe(II) and Fe(III) were nearly equivalent. These findings clearly demonstrate that system design can be optimized with regard to process variables in Fenton's treatment of DNAPL in soils.     

Controlled release, blind test of DNAPL remediation by ethanol flushing

A dense nonaqueous phase liquid (DNAPL) source zone was established within a sheet-pile isolated cell through a controlled release of perchloroethylene (PCE) to evaluate DNAPL remediation by in-situ cosolvent flushing. Ethanol was used as the cosolvent, and the main remedial mechanism was enhanced dissolution based on the phase behavior of the water-ethanol-PCE system. Based on the knowledge of the actual PCE volume introduced into the cell, it was estimated that 83 L of PCE were present at the start of the test. Over a 40-day period, 64% of the PCE was removed by flushing the cell with an alcohol solution of approximately 70% ethanol and 30% water. High removal efficiencies at the end of the test indicated that more PCE could have been removed had it been possible to continue the demonstration. The ethanol solution extracted from the cell was recycled during the test using activated carbon and air stripping treatment. Both of these treatment processes were successful in removing PCE for recycling purposes, with minimal impact on the ethanol content in the treated fluids. Results from pre- and post-flushing partitioning tracer tests overestimated the treatment performance. However, both of these tracer tests missed significant amounts of the PCE present, likely due to inaccessibility of the PCE. The tracer results suggest that some PCE was inaccessible to the ethanol solution which led to the inefficient PCE removal rates observed. The flux-averaged aqueous PCE concentrations measured in the post-flushing tracer test were reduced by a factor of 3 to 4 in the extraction wells that showed the highest PCE removal compared to those concentrations in the pre-flushing tracer test.     

二氧化氯催化氧化处理难降解废水技术的研究

研究了二氧化氯化学氧化体系和二氧化氯催化氧化体系。实验结果表明 :单用二氧化氯化学氧化处理COD为 35 0 0mg/L的酸性大红染料配制废水时 ,最佳反应pH值为 6— 8,氧化剂经济用量为 10 0 0mgClO2 /L废水 ,反应时间为 6 0min ,COD去除率可达 5 0 %左右 ,氧化指数 (COD削减量∶ClO2 投加量 ) =2 .3。当二氧化氯与自制催化剂所组成的催化氧化体系用于对酸性大红染料配制废水的处理时 ,最佳反应pH值为 2左右 ,氧化剂经济用量为 80 0mgClO2 /L废水 ,反应时间为4 5— 6 0min ,COD去除率可达 80 %以上 ,氧化指数 =3.5 ,去除每kgCOD氧化剂费用为 3.7元人民币 ,并且废水的可生化性有很大的提高 ,效果明显优于二氧化氯化学氧化。经济技术评估表明 ,二氧化氯催化氧化法是一种新型高效的处理难降解废水的技术 ,有着广阔的应用前景     

Effect of metal ions and humic acid on the dechlorination of tetrachloroethylene by zerovalent iron

The dechlorination of tetrachloroethylene (PCE) by zerovalent iron (Fe(0)) in the presence of metal ions and humic acid was investigated. In the absence of metal ion and humic acid, 64% of the initial PCE was dechlorinated after 125 h with the production of ethane and ethene as the major end products. The dechlorination followed pseudo-first-order kinetics and the normalized surface rate constant (k(SA)) for PCE dechlorination was (3.43+/-0.61)x10(-3)lm(-2)h(-1). Addition of metal ions enhanced the dechlorination efficiency and rate of PCE, and the enhancement effect followed the order Ni(II)>Cu(II)>Co(II). The k(SA) for PCE dechlorination in the presence of metal ions were 2-84 times higher than that in the absence of metal ions. X-ray photoelectron spectroscopy (XPS) showed that Cu(II) and Ni(II) were reduced by Fe(0) to zerovalent metals, and resulted in the formation of bimetallic system to accelerate the dechlorination reaction. On the contrary, humic acid out-competed the reactive sites on iron surface with PCE, and subsequently decreased the dechlorination efficiency and rate of PCE by Fe(0). However, the reactivity of Fe(0) for PCE dechlorination in the presence of metal ions and humic acid increased by a factor of 3-161 when compared to the iron system containing humic acid alone. Since humic acid and metal ions are the most often found co-existing compounds in the contaminated aquifers with chlorinated hydrocarbons, results obtained in this study is useful to better understand the feasibility of using Fe(0) for long-term application to the remediation of contaminated sites.     

含表面活性剂的采油废水催化氧化处理

对含有表面活性剂的废水(以下简称表活废水)进行了傅里叶红外光谱分析(FTIR),结果表明,废水中所含表面活性剂主要为环烷酸钠。采用次氯酸钙(Ca(ClO)2)和活性炭-Ni催化氧化处理,在Ca(ClO)2投加量为4 500 mg/L,活性炭-Ni投加量为7 000 mg/L时,反应90 min,出水COD为158.91 mg/L,去除率达62.92%。催化氧化出水经沸石吸附处理,在pH为6.85,吸附时间为2 h,沸石投加量为17 g/L的条件下,吸附出水COD和油含量分别为88.92 mg/L和2.53mg/L,去除率分别为45.65%和90.02%,均达到《污水综合排放标准(GB8978-1996)》的一级标准要求。催化剂活性炭-Ni和吸附剂沸石均具有较稳定的活性,在重复使用20次后,出水COD的去除率仅分别降低了1.16%和1.32%。     

Characteristics of MnO2 catalytic ozonation of sulfosalicylic acid and propionic acid in water

The characteristics of different types of MnO₂ catalytic ozonation of sulfosalicylic acid (SSal) and propionic acid (PPA) have been investigated in this paper. The experimental results show the dependence of catalytic activity of MnO₂ on organic compounds and the pH of solutions, but it is independent on the type of MnO₂. For example, three types of MnO₂ have not any catalytic activity when ozonation of PPA under the condition of this experiment. All MnO₂ catalytic ozonation of SSal at pH=1.0 have a greater total organic carbon removal than ozonation alone has, however, at pH=6.8 and 8.5, catalytic efficiency is not observed. Furthermore, the batch experimental results indicate that there are no direct relationship between the activity of metal oxide catalytic decomposition of ozone and that of its catalytic degradation of organic compounds.     

The removal of hydrogen sulfide in solution by ferric and alum water treatment residuals

This work investigated the characteristics and mechanisms of hydrogen sulfide adsorption by ferric and alum water treatment residuals (FARs) in solution. The results indicated that FARs had a high hydrogen sulfide adsorption capacity. pH 7 rather than higher pH (e.g. pH 8-10) was favorable for hydrogen sulfide removal. The Yan model fitted the breakthrough curves better than the Thomas model under varied pH values and concentrations. The Brunauer-Emmett-Teller surface area and the total pore volume of the FARs decreased after the adsorption of hydrogen sulfide. In particular, the volume of pores with a radius of 3-5 nm decreased, while the volume of pores with a radius of 2 nm increased. Therefore, it was inferred that new adsorption sites were generated during the adsorption process. The pH of the FARs increased greatly after adsorption. Moreover, differential scanning calorimetry analysis indicated that elemental sulfur was present in the FARs, while the derivative thermal gravimetry curves indicated the presence of sulfuric acid and sulfurous acid. These results indicated that both oxidization and ligand exchange contribute to the removal of hydrogen sulfide by FARs. Under anaerobic conditions, the maximum amount of hydrogen sulfide released was approximately 0.026 mg g(-1), which was less than 0.19% of the total amount adsorbed by the FARs. The hydrogen sulfide that was released may be re-adsorbed by the FARs and transformed into more stable mineral forms. Therefore, FARs are an excellent adsorbent for hydrogen sulfide.     

介质阻挡放电对湖泊水华蓝藻的去除

采用介质阻挡放电等离子体技术去除太湖水华蓝藻,考察了放电输出功率、空气流速、添加剂(异丙醇、腐植酸)等对蓝藻去除的影响。结果表明,介质阻挡放电能去除太湖水华蓝藻,放电功率100 W,空气流速1.0 L/min,放电18min,在光照强度2 000 lx和25℃下培养4 d,初始叶绿素a浓度为9.58 mg/L藻液中蓝藻去除率达87.8%。增加放电输出功率和空气流速能提高蓝藻的去除效率;腐植酸促进了介质阻挡放电对蓝藻的去除;而异丙醇添加剂抑制了介质阻挡放电的作用。放电处理后,蓝藻细胞内类胡萝卜素含量、SOD活性、MDA含量发生明显变化,介质阻挡放电破坏了蓝藻细胞内含物。     

Sorption and reduction of tetrachloroethylene with zero valent iron and amphiphilic molecules

Effects of surfactants and natural organic matter (NOM) on the sorption and reduction of tetrachloroethylene (PCE) with zero valent iron (ZVI) were examined in this study. PCE reduction by ZVI depended on the ionic type of the surfactants. The removal of PCE and production of TCE with non-ionic Triton X-100 and cationic hexadecyltrimethyl-ammonium (HDTMA) at one-half and two times the critical micelle concentration (CMC) were 1.2-1.8 times higher than without surfactants because of the enhanced PCE partitioning and surface concentration by the sorbed surfactants. When anionic sodium dodecyl benzene sulfonate (SDDBS) at one-half and two times CMC and NOM at 20 mg l(-1) and 50 mg l(-1) concentrations were used, the removal of PCE doubled and TCE production decreased. In the presence of SDDBS, TCE production by ZVI was lower than with HDTMA and Triton X-100 while PCE removal was higher than with the other surfactants.     

Kinetics and mechanism of oxidation of tetrachloroethylene with permanganate

The kinetics, reaction pathways and product distribution of oxidation of tetrachloroethylene (PCE) by potassium permanganate (KMnO4) were studied in phosphate-buffered solutions under constant pH, isothermal, completely mixed and zero headspace conditions. Experimental results indicate that the reaction is first-order with respect to both PCE and KMnO4 and has an activation energy of 9.3+/-0.9 kcal/mol. The second-order rate constant at 20 degrees C is 0.035+/-0.004 M(-1) s(-1), and is independent of pH and ionic strength (I) over a range of pH 3-10 and I approximately 0-0.2 M, respectively. The PCE-KMnO4 reaction may proceed through further oxidation and/or hydrolysis reaction pathways, greatly influenced by the acidity of the solution, to yield CO2(g), oxalic acid, formic acid and glycolic acid. Under acidic conditions (e.g., pH 3), the further oxidation pathway will dominate and PCE tends to be directly mineralized into CO2 and chloride. Under neutral (e.g., pH 7) and alkaline conditions (e.g., pH 10), the hydroxylation pathway dominates the reaction and PCE is primarily transformed into oxalic acid prior to complete PCE mineralization. Moreover, all chlorine atoms in PCE are rapidly liberated during the reaction and the rate of chloride production is very close to the rate of PCE degradation.     

Removal of harmful cyanobacterial blooms in Taihu Lake using local soils. III. Factors affecting the removal efficiency and an in situ field experiment using chitosan-modified local soils

Effects of ionic strength, pH, organic content, cell concentration, and growth phase on the removal of MA cells using chitosan-modified sepiolite were studied in the laboratory. The MA removal efficiency increased with the increase of salinity for normal clay flocculation. In contrast, for chitosan-modified clays/soils, MA removal efficiency increased with the decrease of salinity. The removal efficiency of chitosan-modified sepiolite was not significantly affected by pH (6-9), but dropped dramatically beyond pH 10. Humic acid had a small negative effect on the removal of MA cells. Cells were removed more effectively by clays around the early senescence growth phase than other growth stages. The removal efficiency increased as the cell concentration increased. In a field enclosure of Taihu Lake, a loading of 0.025 g/L chitosan-modified local soils removed 99% algal cells and no increase of chlorophyll-a was observed during the following one month's monitoring process.     

Removal of Cr(VI) and humic acid by using TiO2 photocatalysis

The removal efficiencies of Cr(VI) and HA, using a TiO(2)-mediated photocatalytic process, were investigated with variations in the pH, TiO(2) dosage and Cr(VI)/HA ratio. During the photocatalytic reaction, the total removal of Cr(VI) occurred through adsorption onto TiO(2), as well as its reduction to Cr(III). However, oxidation and adsorption were identified as important removal processes for the treatment of HA. Due to the anionic type adsorption onto TiO(2) and its acid-catalyzed photocatalytic reduction, the removal of Cr(VI) decreased with increasing pH, while that of HA increased with increasing pH. The TiO(2) dosage was also an important parameter for the removal of Cr(VI). As the TiO(2) dosage was increased to 2.5 g l(-1), the removal of Cr(VI) was continuously enhanced, but decreased at dosages above 3 g l(-1) due to the increased blockage of the incident UV light used for the photocatalytic reaction. The removal of Cr(VI) was greatly enhanced when the system contained both HA and Cr(VI) compared to Cr(VI) alone. Also, the removal of HA was greatly enhanced when the system contained both HA and Cr(VI) compared to HA alone. The removal of Cr(VI) was continuously enhanced as the HA concentration gradually increased; however, no further increase was observed above 20 mg l(-1) HA due to the increased absorption of the UV light. This result supports that the photocatalytic reaction, with illuminated TiO(2), could be applied to more effectively treat wastewater containing both Cr(VI) and HA than that containing a single species only.     

Atrazine sorption by hydroxy-interlayered clays and their organic complexes

This study examined the sorption of atrazine by hydroxy-Fe interlayered montmorillonite (FeMt) and its hydroquinone (FeMtHQ), citrate (FeMtCt) and catechol (FeMtCC) complexes as well as by hydroxy-Al interlayered montmorillonite (AlMt) and its hydroquinone (AlMtHQ) and citrate (AlMtCt) complexes. Found among the clays were sorption distribution coefficients (K(d)) ranging from 24 to 123 mL g(-1) and maximum sorption (M) ranging from 2.2 to 16.8 microg g(-1). Both K(d) and M decreased in the order of FeMtCC > FeMtHQ > AlMtHQ > (AlMt = FeMt) > (AlMtCt = FeMtCt). The pH was negatively correlated with both K(d) (r = -0.90, p < 0.001) and M (r = -0.81, p < 0.001). When interlayered clays were associated with humified material (FeMtCC, FeMtHQ, AlMtHQ), both K(d) (r > 0.96, p < 0.01) and M (r > 0.94, p < 0.01) were highly positively correlated with total organic C and alkali-soluble C. However, clays with non-humified organic compounds (FeMtCt and AlMtCt) sorbed less atrazine than clays without any organic C (FeMt and AlMt). This suggests that functional groups of Fe-OH and Al-OH in FeMt and AlMt reduced the available sorption sites for atrazine by making complexes with citrate ions while forming FeMtCt and AlMtCt. The atrazine was sorbed through the hydrophobic interactions with organic compound surfaces as well as through H-bonding and ionic bonding with clay-mineral surfaces.     

零价铁修复受三氯乙烯污染地下水的实验研究

通过批实验和柱实验研究了三氯乙烯（TCE）初始浓度、四氯乙烯(PCE)等对零价铁去除三氯乙烯的影响,并建立了三氯乙烯降解的反应动力学方程。结果表明：（1）零价铁对TCE具有较好的降解效果,反应符合准一级反应动力学方程,表观反应速率常数随TCE浓度的增加而减小;（2）在铁粉充足的条件下,TCE初始浓度对降解效果影响不显著,且TCE去除率皆可达到90%以上;（3）PCE的存在抑制了TCE的脱氯反应。PCE和TCE共存时,TCE的最大去除率仅为64.2%;TCE脱氯反应的表观反应速率明显降低,反应半衰期由TCE单独存在时的6.8～9.7 h增大到66 h～346.5 h。     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.