Comparison of atmospheric concentrations of currently used pesticides between urban and rural areas during intensive application period in Alsace (France) by using XAD-2® based passive samplers

XAD-2® passive samplers (PAS) have been exposed simultaneously for 14 days on two sites, one rural and one urban, situated in Alsace (East of France) during intensive pesticides application in agriculture (between March and September). PAS have been extracted and analyzed for current-used pesticides and lindane with an analytical method coupling accelerated solvent extraction (ASE), solid-phase microextraction (SPME) and GC/MS/MS. Results show the detection of pesticides is linked to the period of application and spatial and temporal variabilities can be observed with these PAS during the selected sampling period. The spatial and temporal variability is comparable to the one previously observed by comparing data obtained with PAS with data from Hi.-Vol. samplers in an urban area. Sampling rates were calculated for some pesticides and values are comparable to the data already available in the literature. From these sampling rates, concentrations in ng m^?3 of pesticides in PAS have been calculated and are in the same order of magnitude as those obtained with Hi.Vol. sampling during the same period of time.     

Variability of atmospheric pesticide concentrations between urban and rural areas during intensive pesticide application

Intensive pesticide use leads to the contamination of water, soil and atmosphere. Atmospheric transport is responsible for pesticide dispersal over long distances. In this study, we evaluate the local dispersal of pesticides from agricultural to urban areas. For this purpose, three high-volume samplers, each equipped with a glass fiber filter and XAD-2 resin for the sampling of particulate and gas phase have been placed in a south-west transect (predominant wind direction) characteristic of rural and urban areas. The urban site (Strasbourg centre) is situated in the middle of two rural sites. Samples were taken simultaneously at three sites during pesticide treatments in autumn and spring 2002–2003. Sampling took place for 24 h at a flow rate of 10–15 m³ h⁻¹. The pesticides studied were those commonly used in the Alsace region for all crops (maize, cereal, vines …). Many of the pesticides analysed in atmospheric samples were not detected or observed very episodically at very low concentrations. For metolachlor, alachlor, trifluralin, atrazine and diflufenican, higher concentrations were observed, essentially during the application of these compounds. Moreover, some “spraying peaks” were observed for alachlor in the south rural site (near crops) at a level of 31 ng m⁻³ on 16–17 May 2003. These results show site and time dependence of atmospheric contamination by pesticides. A limited dispersal was also observed especially in the urban area during the application periods of pesticides.     

Sources of polycyclic hydrocarbons and pesticides in soluble fraction of deposition samples in Kocaeli,Turkey

A wet–dry deposition sampler was located at The Scientific and Technological Research Council of Turkey-National Metrology Institute (TUBITAK-UME) station, and a bulk deposition sampler was placed at the Kad?ll? village to determine the atmospheric deposition flux of polycyclic aromatic hydrocarbons (PAHs) and pesticides (organochlorine and organophosphorus) in soluble fraction of samples in Kocaeli, Turkey. The 28 samples for each wet, dry, and total deposition were collected weekly from March 2006 to March 2007. Gas chromatography-tandem mass spectrometry was used to analyze the samples which were prepared by using solid-phase extraction (SPE) method. The sum of volume weighted mean of deposition fluxes was obtained as 7.43 μg m^?2 day^?1 for wet deposition, 0.28 μg m^?2 day^?1 for dry deposition and 0.54 μg m^?2 day^?1 for bulk deposition samples for PAHs and 9.88 μg m^?2 day^?1 for wet deposition, 4.49 μg m^?2 day^?1 for dry deposition, and 3.29 μg m^?2 day^?1 for bulk deposition samples for pesticides. While benzo(a)anthracene had the highest fluxes among PAH compounds for all types of depositions, guthion and phosphamidon had the highest deposition flux compared with the other pesticides. Benzo(ghi)perylene, dibenz(a,h)anthracene, indeno(1,2,3-c,d)pyrene, benzo(a)pyrene, and acenaphthene were not detected in any of the samples. Beta-HCH, gamma-HCH, and endrin aldehyde were the only compounds among 18 organochlorine pesticides to be detected in all deposition samples. The main sources of pesticides were the high number of greenhouses around the sampling stations. However, all of the organophosphorus pesticides were detected in all deposition samples. The pollution sources were identified as coal and natural gas combustion, petrogenic sources, and traffic for TUBITAK-UME station whereas coal and natural gas combustion and traffic were the main sources for Kad?ll? station by considering the results of factor analysis, ratios, and wind sector analysis.     

Sampling atmospheric pesticides with SPME: Laboratory developments and field study

To estimate the atmospheric exposure of the greenhouse workers to pesticides, solid phase microextraction (SPME) was used under non-equilibrium conditions. Using Fick's law of diffusion, the concentrations of pesticides in the greenhouse can be calculated using pre-determined sampling rates (SRs). Thus the sampling rates (SRs) of two modes of SPME in the lab and in the field were determined and compared. The SRs for six pesticides in the lab were 20.4-48.3 mL min⁻¹ for the exposed fiber and 0.166-0.929 mL min⁻¹ for the retracted fiber. In field sampling, two pesticides, dichlorvos and cyprodinil were detected with exposed SPME. SR with exposed SPME for dichlorvos in the field (32.4 mL min^-1) was consistent with that in the lab (34.5 mL min^-1). SR for dichlorvos in the field (32.4 mL min⁻¹) was consistent with that in the lab (34.5 mL min⁻¹). The trends of temporal concentration and the inhalation exposure were also obtained.     

Polar organic chemical integrative sampler (POCIS) uptake rates for 17 polar pesticides and degradation products: laboratory calibration

Polar organic chemical integrative samplers (POCIS) are useful for monitoring a wide range of chemicals, including polar pesticides, in water bodies. However, few calibration data are available, which limits the use of these samplers for time-weighted average concentration measurements in an aquatic medium. This work deals with the laboratory calibration of the pharmaceutical configuration of a polar organic chemical integrative sampler (pharm-POCIS) for calculating the sampling rates of 17 polar pesticides (1.15?≤?logK _ow?≤?3.71) commonly found in water. The experiment, conducted for 21 days in a continuous water flow-through exposure system, showed an integrative accumulation of all studied pesticides for 15 days. Three compounds (metalaxyl, azoxystrobine, and terbuthylazine) remained integrative for the 21-day experiment. The sampling rates measured ranged from 67.9 to 279 mL?day^?1 and increased with the hydrophobicity of the pesticides until reaching a plateau where no significant variation in sampling rate is observed when increasing the hydrophobicity.     

Solventless sample preparation for pesticides analysis in environmental water samples using solid-phase microextraction-high resolution gas chromatography/mass spectrometry (SPME-HRGC/MS)

Solid-phase micro-extraction (SPME) coupled on line with high resolution gas chromatography and mass spectrometric detection is described for the analysis of pesticides in environmental water samples. Experiments were performed in order to optimize the SPME extraction conditions for selected pesticides including tiomethon, trichorfon, dimethoate, diazinon, malathion, dicofol, methidathion, ethion, bromopropylate and pyrazophos from spiked water solutions. To enhance the SPME efficiency, experimental conditions including the fiber composition, stirring rate, temperature, adsorption time, desorption time and salt concentration were optimized. After validation, the SPME-GC/MS methodology was applied to real-world environmental water samples.     

Validation and application of an analytical method for determining pesticides in the gas phase of ambient air

A method for determining atmospheric concentrations of eight pesticides applied to corn and soybean crops in Mato Grosso state, Brazil is presented. The method involved a XAD-2 resin cartridge coupled to a low volume air pump at 2 L min?1 over 8 hours. Pesticides were recovered from the resin using sonication with n-hexane:ethyl acetate and determined by GC-MS. Good accuracy (76-128%) and precision (CV < 20%) were obtained for atrazine, chlorpyrifos, alpha- and beta-endosulfan, endosulfan sulfate, flutriafol, malathion, metolachlor and permethrin. Method detection ranged from 9.0 to 17.9 ng m?3. This method was applied to 61 gas phase samples collected between December 2008 and June 2009. Atrazine and endosulfan were detected both in urban and rural areas indicating the importance of atmospheric dispersion of pesticides in tropical areas. The simple and efficient extraction method and sampling system employed was considered suitable for identifying pesticides in areas of intense agricultural production.     

Air sampling and analysis of volatile organic compounds with solid phase microextraction

Solid phase microextraction (SPME) presents many advantages over conventional analytical methods by combining sampling, preconcentration, and direct transfer of the analytes into a standard gas chromatograph (GC). Since its commercial introduction in the early 1990s, SPME has been successfully applied to the sampling and analysis of environmental samples. This paper presents an overview of the current methods for air sampling and analysis with SPME using both grab and time-weighted average (TWA) modes. Methods include total volatile organic compounds (TVOCs), formaldehyde, and several target volatile organic compounds (VOCs). Field sampling data obtained with these methods in indoor air were validated with conventional methods based on sorbent tubes. The advantages and challenges associated with SPME for air sampling are also discussed. SPME is accurate, fast, sensitive, versatile, and cost-efficient, and could serve as a powerful alternative to conventional methods used by the research, industrial, regulatory, and academic communities.     

Comments on the NAS Report: Odors From Stationary and Mobile Sources

ABSTRACT

Solid phase microextraction (SPME) presents many advantages over conventional analytical methods by combining sampling, preconcentration, and direct transfer of the analytes into a standard gas chromatograph (GC). Since its commercial introduction in the early 1990s, SPME has been successfully applied to the sampling and analysis of environmental samples. This paper presents an overview of the current methods for air sampling and analysis with SPME using both grab and time-weighted average (TWA) modes. Methods include total volatile organic compounds (TVOCs), formaldehyde, and several target volatile organic compounds (VOCs). Field sampling data obtained with these methods in indoor air were validated with conventional methods based on sorbent tubes. The advantages and challenges associated with SPME for air sampling are also discussed. SPME is accurate, fast, sensitive, versatile, and cost-efficient, and could serve as a powerful alternative to conventional methods used by the research, industrial, regulatory, and academic communities.     

Comparison between solid-phase extraction methods for the chromatographic determination of organophosphorus pesticides in water

A solid-phase microextraction (SPME) procedure has been developed to extract eight organophosphorus pesticides (OPs) in water and the method was compared with a conventional solid phase extraction (SPE) technique. The extracted OPs were analyzed by gas chromatography using thermionic specific detection. Both extraction methods presented linear calibration at least over the concentration range investigated (100 to 1000 ng x mL(-1) for SPE and 1 to 100 ng x mL(-1) for SPME). SPME method presented higher sensitivity than SPE. The quantitation limits were between 0.1 to 1.0 ng x mL(-1) for SPME depending upon the analyte, and 100 ng x mL(-1) for SPE. The precision, as measured by the standard deviations (RSD), were in the range 3.6% to 5.8% for SPME and 2.4% to 9.2% for SPE. Along with the feature of being a solvent - free sampling technique, SPME offers additional benefits due to its high sensitivity, simplicity, and small size sample required (typically: SPE - 500 mL, SPME - 5 mL).     

Validation and application of an analytical method for determining pesticides in the gas phase of ambient air

A method for determining atmospheric concentrations of eight pesticides applied to corn and soybean crops in Mato Grosso state, Brazil is presented. The method involved a XAD-2 resin cartridge coupled to a low volume air pump at 2 L min^?1 over 8 hours. Pesticides were recovered from the resin using sonication with n-hexane:ethyl acetate and determined by GC-MS. Good accuracy (76–128%) and precision (CV < 20%) were obtained for atrazine, chlorpyrifos, alpha- and beta-endosulfan, endosulfan sulfate, flutriafol, malathion, metolachlor and permethrin. Method detection ranged from 9.0 to 17.9 ng m^?3. This method was applied to 61 gas phase samples collected between December 2008 and June 2009. Atrazine and endosulfan were detected both in urban and rural areas indicating the importance of atmospheric dispersion of pesticides in tropical areas. The simple and efficient extraction method and sampling system employed was considered suitable for identifying pesticides in areas of intense agricultural production.     

Wood-Specific Polycyclic Aromatic Hydrocarbon (PAH) Patterns in Soot Using Gas Chromatography-Atmospheric Pressure Laser Ionization-Mass Spectrometry (GC-APLI-MS)

If organic matter is burnt, the combustion of wood produces the highest amounts of polycyclic aromatic hydrocarbons (PAHs) compared with other fossil energy sources such as oil, coal, or gas. Emissions from wood combustion are increasingly of special interest due to the rising use of wood as a renewable energy source in residential heating in Europe. To the authors' knowledge, reproducible wood-specific PAH patterns in soot were identified for the first time by use of a sampling interval of only 5 min in this study. The short sampling interval was enabled by the very sensitive analytical method of gas chromatography–atmospheric pressure laser ionization–mass spectrometry (GC-APLI-MS) applied. The analysis of 40 PAH of soot from wood logs of spruce, pine, larch (softwood) and beech, birch, oak (hardwood), and wood pellets, as well as wood briquettes, showed 13.46–250.62 mg/kg for ∑40 PAH and 10.75–177.94 mg/kg for the U.S. Environmental Protection Agency PAH standard (without acenaphthylene and anthracene). Highest concentrations occurred in the samples from birch with bark, beech, and wood briquettes. Indeno[1,2,3-cd]pyrene, naphthalene, and alkylated naphthalenes were also detected. Significant concentrations of the very toxic dibenzopyrenes (up to 11.30 mg/kg) are reported. Softwood soot contained highest amounts of 2–4-ring PAH, followed by hardwood which is in accordance with the presence of highest amounts of abietic acid in softwood, a known precursor of retene and phenanthrene. PAH in soot from five spruce samples from different locations show a mean ∑40 PAH concentration of 13.46 mg/kg (n = 5, minimum 8.03, maximum 23.32 mg/kg, SD = 5.65) and exhibited a typical pattern that differed from all other wood soot samples. The distributions of alkylated naphthalenes of the spruce samples show a bell-shape distribution in contrast to the alkylated phenanthrenes/anthracenes of all samples (except the wood pellets), showing a slope distribution. The data indicate that wood-specific PAH patterns exist and under the applied conditions, spruce logs produced the least toxic soot.     

Atmospheric pathways of chlorinated pesticides and natural bromoanisoles in the northern Baltic Sea and its catchment

Long-range atmospheric transport is a major pathway for delivering persistent organic pollutants to the oceans. Atmospheric deposition and volatilization of chlorinated pesticides and algae-produced bromoanisoles (BAs) were estimated for Bothnian Bay, northern Baltic Sea, based on air and water concentrations measured in 2011–2012. Pesticide fluxes were estimated using monthly air and water temperatures and assuming 4 months ice cover when no exchange occurs. Fluxes were predicted to increase by about 50 % under a 2069–2099 prediction scenario of higher temperatures and no ice. Total atmospheric loadings to Bothnian Bay and its catchment were derived from air–sea gas exchange and “bulk” (precipitation + dry particle) deposition, resulting in net gains of 53 and 46 kg year^?1 for endosulfans and hexachlorocyclohexanes, respectively, and net loss of 10 kg year^?1 for chlordanes. Volatilization of BAs releases bromine to the atmosphere and may limit their residence time in Bothnian Bay. This initial study provides baseline information for future investigations of climate change on biogeochemical cycles in the northern Baltic Sea and its catchment.     

COMPARISON BETWEEN SOLID–PHASE EXTRACTION METHODS FOR THE CHROMATOGRAPHIC DETERMINATION OF ORGANOPHOSPHORUS PESTICIDES IN WATER

A solid-phase microextraction (SPME) procedure has been developed to ex tract eight organophosphorus pesticides (OPs) in water and the method was compared with a conventional solid phase extraction (SPE) technique. The extracted OPs were analyzed by gas chromatography using thermionic specific detection. Both extraction methods presented linear calibration at least over the concentration range investigated (100 to 1000 ng.mL^?1 for SPE and 1 to 100 ng.mL^?1 for SPME). SPME method presented higher sensitivity than SPE. The quantitation limits were between 0.1 to 1.0 ng.mL^?1 for SPME depending upon the analyte, and 100 ng.mL^?1 for SPE. The precision, as measured by the standard deviations (RSD), were in the range 3.6 % to 5.8 % for SPME and 2.4 % to 9.2 % for SPE.

Along with the feature of being a solvent – free sampling technique, SPME offers additional benefits due to its high sensitivity, simplicity, and small size sample required (typically: SPE – 500 mL, SPME – 5 mL).     

Survey regarding the occurrence of selected organic micropollutants in the groundwaters of overseas departments

To collect a complete dataset regarding the occurrence of organic substances in groundwater, this study presents the examination of 66 organic contaminants in the groundwater of overseas departments, including pesticides, pharmaceutical compounds, hormones and some industrial substances. The selective and sensitive analytical methods are described. These techniques begin with solid-phase extraction (SPE) followed by analysis using liquid chromatography–tandem mass spectrometry (LC-MS/MS) and gas chromatography–mass spectrometry (GC-ToF-MS). The paper summarises the analytical results from 40 sampling points collected during two campaigns in Guadeloupe, Martinique, Reunion, Mayotte and Guiana, representing 80 samples. Of the 66 target substances, 36 were determined at least once. Among the most frequently detected are bisphenol A (frequency, 96 %; max., 7,400 ng/L), caffeine (frequency, 91 %; max., 1,240 ng/L), pentachlorophenol (frequency, 55 %; max., 418 ng/L), and carbamazepine (frequency, 56 %; max., 22 ng/L). The results do not put in evidence that the origin of the sample or climatic characteristics of these regions influence the dilution and release of micropollutants.     

Analysis of Organophosphorus Pesticides in Whole Milk by Solid Phase Microextraction Gas Chromatography Method

Solid phase microextraction (SPME) was used for the extraction of residual coumaphos and dichlorvos in whole milk. The residues were analyzed by capillary gas chromatography equipped with nitrogen phosphorus detector (GC-NPD). A manual SPME holder with a 100-μm polyacrylate fiber was used. The optimized conditions for extraction by SPME method were: sample agitation, absorption temperature of 30°C, absorption time of 40 min, desorption time of 10 min, and sample volume was 16.0 mL in the vial. Under these conditions, the calibration graphs were linear in the range of 0.17 μgL^?1 to 1.75 μgL^?1 for coumaphos and 0.69 μgL^?1 to 6.90 μgL^?1 for dichlorvos. Precision was good with RSD values of 13% for coumaphos and 14% for dichlorvos. The detection limits (LOD) were 0.060 μgL^?1 for dichlorvos and 0.052 for coumaphos. The quantification limits (LOQ) were 0.086 μgL^?1 for dichlorvos and 0.066 μgL^?1 for coumaphos. The results obtained in this study suggest that SPME is a suitable technique for residual pesticide analysis of milk. The data demonstrate that particular OP pesticides used in dairy farming in the region of Minas Gerais were found to contaminate cow whole milk, and the residues are not removed by treating the milk by boiling.     

Analysis of organophosphorus pesticides in whole milk by solid phase microextraction gas chromatography method

Solid phase microextraction (SPME) was used for the extraction of residual coumaphos and dichlorvos in whole milk. The residues were analyzed by capillary gas chromatography equipped with nitrogen phosphorus detector (GC-NPD). A manual SPME holder with a 100-microm polyacrylate fiber was used. The optimized conditions for extraction by SPME method were: sample agitation, absorption temperature of 30 degrees C, absorption time of 40 min, desorption time of 10 min, and sample volume was 16.0 mL in the vial. Under these conditions, the calibration graphs were linear in the range of 0.17 microgL-1 to 1.75 microgL-1 for coumaphos and 0.69 microgL-1 to 6.90 microgL-1 for dichlorvos. Precision was good with RSD values of 13% for coumaphos and 14% for dichlorvos. The detection limits (LOD) were 0.060 microgL-1 for dichlorvos and 0.052 for coumaphos. The quantification limits (LOQ) were 0.086 microgL-1 for dichlorvos and 0.066 microgL-1 for coumaphos. The results obtained in this study suggest that SPME is a suitable technique for residual pesticide analysis of milk. The data demonstrate that particular OP pesticides used in dairy farming in the region of Minas Gerais were found to contaminate cow whole milk, and the residues are not removed by treating the milk by boiling.     

Primary product distribution from the Cl-atom initiated atmospheric degradation of furan: Environmental implications

Furan is an aromatic hydrocarbon present in both urban and rural atmospheres, which is emitted mainly by biomass burning and the combustion of fossil fuel. Reaction of furan and Cl atoms may be important in areas where chlorine atom concentrations are potentially high such as marine and coastal regions or continental atmospheres where industrial activity emits molecular chlorine or photo-labile Cl-containing compounds. To assess the importance of this reaction and to investigate whether any unique chlorine-containing product is formed the products of the reaction of Cl atoms with furan have been determined under atmospheric conditions. For the study two different sampling/detection methods have been used: (1) Solid-Phase MicroExtraction, with subsequent analysis by thermal desorption, and gas chromatography with mass spectrometry or flame ionization detection (SPME/GC-MS/FID), and 2-“in situ” with long path fourier transform infrared spectroscopy (FTIR). The yields of primary reaction products in the absence of NO were: 5-chloro-2(5H)-furanone (64.5±10.7)%, E-butenedial (11±3)%, 5-hydroxy-2(5H)-furanone (⩽2.4%) and Z-butenedial (1.6±0.5)%. Other products generated by secondary reactions were 2(3H)-furanone (2.8±1.9)%, HCl (21.1±3%) and CO. Maleic anhydride was detected with a yield of about 2%, however, this yield may be a combination of both primary and secondary reactions. All errors are ±2σ. The observed products confirm that addition of Cl atoms to the double bond of furan is the dominant reaction pathway.     

The dissipation of three fungicides in a biobed organic substrate and their impact on the structure and activity of the microbial community

Biopurification systems (BPS) have been introduced to minimise the risk for point source contamination of natural water resources by pesticides. Their depuration efficiency relies mostly on the high biodegradation of their packing substrate (biomixture). Despite that, little is known regarding the interactions between biomixture microflora and pesticides, especially fungicides which are expected to have a higher impact on the microbial community. This study reports the dissipation of the fungicides azoxystrobin (AZX), fludioxonil (FL) and penconazole (PC), commonly used in vineyards, in a biomixture composed of pruning residues and straw used in vineyard BPS. The impact of fungicides on the microbial community was also studied via microbial biomass carbon, basal respiration and phospholipid fatty acid analysis. AZX dissipated faster (t _1/2?=?30.1 days) than PC (t _1/2?=?99.0 days) and FL (t _1/2?=?115.5 days). Fungicides differently affected the microbial community. PC showed the highest adverse effect on both the size and the activity of the biomixture microflora. A significant change in the structure of the microbial community was noted for PC and FL, and it was attributed to a rapid inhibition of the fungal fraction while bacteria showed a delayed response which was attributed to indirect effects by the late proliferation of fungi. All effects observed were transitory and a full recovery of microbial indices was observed 60 days post-application. Overall, no clear link between pesticide persistence and microbial responses was observed stressing the complex nature of interactions between pesticides in microflora in BPS.