Nitrate removal to its fate in wetland mesocosm filled with sponge iron: Impact of influent COD/N ratio

• CW-Fe allowed a high-performance of NO₃^‒-N removal at the COD/N ratio of 0. • Higher COD/N resulted in lower chem-denitrification and higher bio-denitrification. • The application of s-Fe⁰ contributed to TIN removal in wetland mesocosm. • s-Fe⁰ changed the main denitrifiers in wetland mesocosm. Sponge iron (s-Fe⁰) is a porous metal with the potential to be an electron donor for denitrification. This study aims to evaluate the feasibility of using s-Fe⁰ as the substrate of wetland mesocosms. Here, wetland mesocosms with the addition of s-Fe⁰ particles (CW-Fe) and a blank control group (CW-CK) were established. The NO₃^‒-N reduction property and water quality parameters (pH, DO, and ORP) were examined at three COD/N ratios (0, 5, and 10). Results showed that the NO₃^‒-N removal efficiencies were significantly increased by 6.6 to 58.9% in the presence of s-Fe⁰. NH₄⁺-N was mainly produced by chemical denitrification, and approximately 50% of the NO₃^‒-N was reduced to NH₄⁺-N, at the COD/ratio of 0. An increase of the influent COD/N ratio resulted in lower chemical denitrification and higher bio-denitrification. Although chemical denitrification mediated by s-Fe⁰ led to an accumulation of NH₄⁺-N at COD/N ratios of 0 and 5, the TIN removal efficiencies increased by 4.5%‒12.4%. Moreover, the effluent pH, DO, and ORP values showed a significant negative correlation with total Fe and Fe (II) (P<0.01). High-throughput sequencing analysis indicated that Trichococcus (77.2%) was the most abundant microorganism in the CW-Fe mesocosm, while Thauera, Zoogloea, and Herbaspirillum were the primary denitrifying bacteria. The denitrifiers, Simplicispira, Dechloromonas, and Denitratisoma, were the dominant bacteria for CW-CK. This study provides a valuable method and an improved understanding of NO₃^‒-N reduction characteristics of s-Fe⁰ in a wetland mesocosm.     

Scrap Iron Filings assisted nitrate and phosphate removal in low C/N waters using mixed microbial culture

• Microbes enhance denitrification under varying DO concentrations and SIF dosages. • Abiotic nitrate reduction rates are proportional to SIF age and dosage. • Over 80% of the simultaneously loaded NO₃⁻-N and PO₄³⁻ is removed biologically. This study focuses on identifying the factors under which mixed microbial seeds assist bio-chemical denitrification when Scrap Iron Filings (SIF) are used as electron donors and adsorbents in low C/N ratio waters. Batch studies were conducted in abiotic and biotic reactors containing fresh and aged SIF under different dissolved oxygen concentrations with NO₃⁻-N and/or PO₄^3- influent(s) and their nitrate/phosphate removal and by-product formations were studied. Batch reactors were seeded with a homogenized mixed microbial inoculum procured from natural sludges which were enriched over 6 months under denitrifying conditions in the presence of SIF. Results indicated that when influent containing 40 mg/L of NO₃⁻-N was treated with 5 g SIF, 79.9% nitrate reduction was observed in 8 days abiotically and 100% removal was accomplished in 20 days when the reactor was seeded. Both abiotic and seeded reactors removed more than 92% PO₄³⁻ under high DO conditions in 12 days. Abiotic and biochemical removal of NO₃⁻-N and abiotic removal of PO₄³⁻ were higher under independent NO₃⁻-N/PO₄³⁻ loading, while 99% PO₄^3- was removed biochemically under combined NO₃⁻-N and PO₄³⁻ loading. This study furthers the understandings of nitrate and phosphate removal in Zero Valent Iron (ZVI) assisted mixed microbial systems to encourage the application of SIF-supported bio-chemical processes in the simultaneous removals of these pollutants.     

Removal of ammonium and nitrate through Anammox and FeS-driven autotrophic denitrification

● Simultaneous NH₄⁺/NO₃^– removal was achieved in the FeS denitrification system ● Anammox coupled FeS denitrification was responsible for NH₄⁺/NO₃^– removal ● Sulfammox, Feammox and Anammox occurred for NH₄⁺ removal ● Thiobacillus, Nitrospira , and Ca. Kuenenia were key functional microorganisms An autotrophic denitrifying bioreactor with iron sulfide (FeS) as the electron donor was operated to remove ammonium (NH₄⁺) and nitrate (NO₃⁻) synergistically from wastewater for more than 298 d. The concentration of FeS greatly affected the removal of NH₄⁺/NO₃⁻. Additionally, a low hydraulic retention time worsened the removal efficiency of NH₄⁺/NO₃⁻. When the hydraulic retention time was 12 h, the optimal removal was achieved with NH₄⁺ and NO₃⁻ removal percentages both above 88%, and the corresponding nitrogen removal loading rates of NH₄⁺ and NO₃⁻ were 49.1 and 44.0 mg/(L·d), respectively. The removal of NH₄⁺ mainly occurred in the bottom section of the bioreactor through sulfate/ferric reducing anaerobic ammonium oxidation (Sulfammox/Feammox), nitrification, and anaerobic ammonium oxidation (Anammox) by functional microbes such as Nitrospira, Nitrosomonas, and Candidatus Kuenenia. Meanwhile, NO₃⁻ was mainly removed in the middle and upper sections of the bioreactor through autotrophic denitrification by Ferritrophicum, Thiobacillus, Rhodanobacter, and Pseudomonas, which possessed complete denitrification-related genes with high relative abundances.     

Fungal diversity and its mechanism of community shaping in the milieu of sanitary landfill

• Ascomycota was the predominant phylum in sanitary landfill fungal communities. • Saprophytic fungi may be of special importance in landfill ecology. • Both richness and diversity of fungal community were lower in leachate than refuse. • Physical habitat partly contributed to the geographic variance of fungal community. • NO₃⁻ was considered the most significant abiotic factor shaping fungal community. Land filling is the main method to dispose municipal solid waste in China. During the decomposition of organic waste in landfills, fungi play an important role in organic carbon degradation and nitrogen cycling. However, fungal composition and potential functions in landfill have not yet been characterized. In this study, refuse and leachate samples with different areas and depths were taken from a large sanitary landfill in Beijing to identify fungal communities in landfills. In high-throughput sequencing of ITS region, 474 operational taxonomic units (OTUs) were obtained from landfill samples with a cutoff level of 3% and a sequencing depth of 19962. The results indicates that Ascomycota, with the average relative abundance of 84.9%, was the predominant phylum in landfill fungal communities. At the genus level, Family Hypocreaceae unclassified (15.7%), Fusarium (9.9%) and Aspergillus (8.3%) were the most abundant fungi found in the landfill and most of them are of saprotrophic lifestyle, which plays a big role in nutrient cycling in ecosystem. Fungi existed both in landfilled refuse and leachate while both the richness and evenness of fungal communities were higher in the former. In addition, fungal communities in landfilled refuse presented geographic variances, which could be partly attributed to physical habitat properties (pH, dissolved organic carbon, volatile solid, NH₄⁺, NO₂⁻ and NO₃⁻), while NO₃⁻ was considered the most significant factor (p<0.05) in shaping fungal community.     

Partial anammox achieved in full scale biofilm process for typical domestic wastewater treatment

• A full scale biofilm process was developed for typical domestic wastewater treatment. • The HRT was 8 h and secondary sedimentation tank was omitted. • Candidatus Brocadia were enriched in the HBR with an abundance of 2.89%. • Anammox enabled a stable ammonium removal of ~15% in the anoxic zone. The slow initiation of anammox for treating typical domestic wastewater and the relatively high footprint of wastewater treatment infrastructures are major concerns for practical wastewater treatment systems. Herein, a 300 m³/d hybrid biofilm reactor (HBR) process was developed and operated with a short hydraulic retention time (HRT) of 8 h. The analysis of the bacterial community demonstrated that anammox were enriched in the anoxic zone of the HBR process. The percentage abundance of Candidatus Brocadia in the total bacterial community of the anoxic zone increased from 0 at Day 1 to 0.33% at Day 130 and then to 2.89% at Day 213. Based upon the activity of anammox bacteria, the removal of ammonia nitrogen (NH₄⁺-N) in the anoxic zone was approximately 15%. This showed that the nitrogen transformation pathway was enhanced in the HBR system through partial anammox process in the anoxic zone. The final effluent contained 12 mg/L chemical oxygen demand (COD), 0.662 mg/L NH₄⁺-N, 7.2 mg/L total nitrogen (TN), and 6 mg/L SS, indicating the effectiveness of the HBR process for treating real domestic wastewater.     

Sludge fermentation liquid addition attained advanced nitrogen removal in low C/N ratio municipal wastewater through short-cut nitrification-denitrification and partial anammox

• Sludge fermentation liquid addition resulted in a high NAR of 97.4%. • Extra NH₄⁺-N from SFL was removed by anammox in anoxic phase. • Nitrogen removal efficiency of 92.51% was achieved in municipal wastewater. • The novel system could efficiently treat low COD/N municipal wastewater. Biological nitrogen removal of wastewater with low COD/N ratio could be enhanced by the addition of wasted sludge fermentation liquid (SFL), but the performance is usually limited by the introducing ammonium. In this study, the process of using SFL was successfully improved by involving anammox process. Real municipal wastewater with a low C/N ratio of 2.8–3.4 was treated in a sequencing batch reactor (SBR). The SBR was operated under anaerobic-aerobic-anoxic (AOA) mode and excess SFL was added into the anoxic phase. Stable short-cut nitrification was achieved after 46d and then anammox sludge was inoculated. In the stable period, effluent total inorganic nitrogen (TIN) was less than 4.3 mg/L with removal efficiency of 92.3%. Further analysis suggests that anammox bacteria, mainly affiliated with Candidatus_Kuenenia, successfully reduced the external ammonia from the SFL and contributed approximately 28%–43% to TIN removal. Overall, this study suggests anammox could be combined with SFL addition, resulting in a stable enhanced nitrogen biological removal.     

Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

Four kinds of capping materials for controlling phosphorus and nitrogen release from contaminated sediment using a static simulation experiment

• Lanthanum modified bentonite (LMB) can effectively absorb phosphorus (P). • Water treatment plant sludge (WTPS) capping is effective for controlling P release. •Aluminum-based P-inactivation agent (Al-PIA) is an efficient P control material. •The P adsorbed by WTPS and Al-PIA is mainly in the form of NAIP. We determined the effects of quartz sand (QS), water treatment plant sludge (WTPS), aluminum-based P-inactivation agent (Al-PIA), and lanthanum-modified bentonite (LMB) thin-layer capping on controlling phosphorus and nitrogen release from the sediment, using a static simulation experiment. The sediment in the experiment was sampled from Yundang Lagoon (Xiamen, Fujian Province, China), which is a eutrophic waterbody. The total phosphorus (TP), ammonium nitrogen (NH₄⁺-N), and total organic carbon (TOC) levels in the overlying water were measured at regular intervals, and the changes of different P forms in WTPS, Al-PIA, and sediment of each system were analyzed before and after the test. The average TP reduction rates of LMB, Al-PIA, WTPS, and QS were 94.82, 92.14, 86.88, and 10.68%, respectively, when the release strength of sediment TP was 2.26–9.19 mg/(m²·d) and the capping strength of the materials was 2 kg/m². Thin-layer capping of LMB, WTPS, and Al-PIA could effectively control P release from the sediment (P<0.05). However, thin-layer capping of LMB, Al-PIA, and QS did not significantly reduce the release of ammonium N and organic matter (P > 0.05). Based on our results, LMB, Al-PIA, and WTPS thin-layer capping promoted the migration and transformation of easily released P in sediment. The P adsorbed by WTPS and Al-PIA mainly occurred in the form of NAIP.     

Sulfur cycle as an electron mediator between carbon and nitrate in a constructed wetland microcosm

• Fe(III) accepted the most electrons from organics, followed by NO₃^‒, SO₄^2‒, and O₂. • The electrons accepted by SO₄^2‒ could be stored in the solid AVS, FeS₂-S, and S⁰. • The autotrophic denitrification driven by solid S had two-phase characteristics. • A conceptual model involving electron acceptance, storage, and donation was built. • S cycle transferred electrons between organics and NO₃^‒ with an efficiency of 15%. A constructed wetland microcosm was employed to investigate the sulfur cycle-mediated electron transfer between carbon and nitrate. Sulfate accepted electrons from organics at the average rate of 0.84 mol/(m³·d) through sulfate reduction, which accounted for 20.0% of the electron input rate. The remainder of the electrons derived from organics were accepted by dissolved oxygen (2.6%), nitrate (26.8%), and iron(III) (39.9%). The sulfide produced from sulfate reduction was transformed into acid-volatile sulfide, pyrite, and elemental sulfur, which were deposited in the substratum, storing electrons in the microcosm at the average rate of 0.52 mol/(m³·d). In the presence of nitrate, the acid-volatile and elemental sulfur were oxidized to sulfate, donating electrons at the average rate of 0.14 mol/(m³·d) and driving autotrophic denitrification at the average rate of 0.30 g N/(m³·d). The overall electron transfer efficiency of the sulfur cycle for autotrophic denitrification was 15.3%. A mass balance assessment indicated that approximately 50% of the input sulfur was discharged from the microcosm, and the remainder was removed through deposition (49%) and plant uptake (1%). Dominant sulfate-reducing (i.e., Desulfovirga, Desulforhopalus, Desulfatitalea, and Desulfatirhabdium) and sulfur-oxidizing bacteria (i.e., Thiohalobacter, Thiobacillus, Sulfuritalea, and Sulfurisoma), which jointly fulfilled a sustainable sulfur cycle, were identified. These results improved understanding of electron transfers among carbon, nitrogen, and sulfur cycles in constructed wetlands, and are of engineering significance.     

Methanation and chemolitrophic nitrogen removal by an anaerobic membrane bioreactor coupled partial nitrification and Anammox

● Efficient carbon methanation and nitrogen removal was achieved in AnMBR-PN/A system. ● AOB outcompeted NOB in PN section by limiting aeration and shortening SRT. ● The moderate residual organic matter of PN section triggered PD in anammox unit. ● AnAOB located at the bottom of UASB played an important role in nitrogen removal. An AnMBR-PN/A system was developed for mainstream sewage treatment. To verify the efficient methanation and subsequent chemolitrophic nitrogen removal, a long-term experiment and analysis of microbial activity were carried out. AnMBR performance was less affected by the change of hydraulic retention time (HRT), which could provide a stable influent for subsequent PN/A units. The COD removal efficiency of AnMBR was > 93% during the experiment, 85.5% of COD could be recovered in form of CH₄. With the HRT of PN/A being shortened from 10 to 6 h, nitrogen removal efficiency (NRE) of PN/A increased from 60.5% to 80.4%, but decreased to 68.8% when the HRT_PN/A further decreased to 4 h. Microbial analysis revealed that the highest specific ammonia oxidation activity (SAOA) and the ratio of SAOA to specific nitrate oxidation activity (SNOA) provide stable NO₂⁻-N/NH₄⁺-N for anammox, and anammox bacteria (mainly identified as Candidatus Brocadia) enriched at the bottom of Anammox-UASB might play an important role in nitrogen removal. In addition, the decrease of COD in Anammox-UASB indicated partial denitrification occurred, which jointly promoted nitrogen removal with anammox.     

Enhanced nitrogen removal and microbial analysis in partially saturated constructed wetland for treating anaerobically digested swine wastewater

Anaerobically digested swine wastewater was treated by a novel constructed wetland. Tidal operation was better for total nitrogen removal than intermittent flow. Mechanism of nitrogen removal by biozeolite-based constructed wetland was discussed. Simultaneous nitrification and denitrification were determined in zeolite layer. Nitrogen removal of wastewater containing high-strength ammonium by the constructed wetlands (CWs) has been paid much attention. In this study, the ability of a partially saturated CW to treat anaerobically-digested decentralized swine wastewater under varying operating parameters from summer to winter was investigated. The partially saturated CW achieved better NH₄⁺-N and TN removal by tidal flow than intermittent flow. With surface loading rates of 0.108, 0.027, and 0.029 kg/(m²·d) for COD, NH₄⁺-N, and TN, the partially saturated CW by tidal operation achieved corresponding removal efficiencies of 85.94%, 61.20%, and 57.41%, respectively, even at 10°C. When the rapid-adsorption of NH₄⁺-N and the bioregeneration of zeolites reached dynamically stable, the simultaneous nitrification and denitrification in the aerobic zeolite layer was observed and accounted for 58.82% of the total denitrification of CW. The results of Illumina high-throughput sequencing also indicated that nitrifiers (Nitrospira and Rhizomicrobium) and denitrifiers (Rhodanobacter and Thauera) simultaneously existed in the zeolite layer. The dominant existence of versatile organic degraders and nitrifiers/denitrifiers in the zeolite layer was related to the removal of most COD and nitrogen in this zone. The contribution of the possible nitrogen removal pathways in the CW was as follows: nitrification-denitrification (86.55%)>substrate adsorption (11.70%)>plant uptake (1.15%)>microbial assimilation (0.60%).     

Sugarcane bagasse amendment improves the quality of green waste vermicompost and the growth of Eisenia fetida

•Earthworms were able to convert green waste into more plant-available nutrients. •The part of heavy metals content increased in the compost added by earthworm. •The addition of SCB to GW did enhance earthworm biomass and humic acid content. •The resulting vermicomposts were characterized by neutral pH and lower EC value. Vermicomposting is a feasible method for disposing of lignocellulosic waste while generating a useful product. The current study assessed the potential of vermicomposting green waste mixed with sugarcane bagasse in proportions of 25%, 50%, and 75% (v:v, based on dry weight). The suitability was evaluated based on the agrochemical properties, earthworm biomass, and phytotoxicity. The final vermicomposts exhibited near-neutral pH values (7.1–7.6), and lower EC values (0.43–0.72 mS/cm) and C:N ratios (14.1–19.9).The content of available nutrients and CEC for all the vermicomposts exceeded those of the control compost (without earthworms). For vermicomposts, the average values of NO₃^–-N, AP, AK, and CEC were 53, 517, 1362 mg/kg, and 158 cmol/kg, respectively. The total contents of heavy metals increased in all vermicompost treatments compared to control composts with the following average final percentages: Zn (2.0%), Cr (15.5%), Pb (23.4%), and Cu (44.3%), but these amounts were safe for application in agroforestry. The addition of sugarcane bagasse to green waste significantly increased the content of total humic substance, humic acid and urease activity, acid and alkaline phosphatase activity, and Eiseniafetida reproduction. The addition of 25% sugarcane bagasse to green waste decreased the toxicity to germinating seeds. These results revealed that vermicomposting is a feasible way to degrade green waste into a value-added chemical product.     

Nitrogen removal efficiencies and microbial communities in full-scale IFAS and MBBR municipal wastewater treatment plants at high COD:N ratio

• Two IFAS and two MBBR full-scale systems (high COD:N ratio 8:1) were characterized. • High specific surface area carriers grew and retained slow-growing nitrifiers. • High TN removal is related to high SRT and low DO concentration in anoxic tanks. The relative locations of AOB, NOB, and DNB were examined for three different kinds of carriers in two types of hybrid biofilm process configurations: integrated fixed-film activated sludge (IFAS) and moving bed biofilm reactor (MBBR) processes. IFAS water resource recovery facilities (WRRFs) used Anodkalness^TM K1 carriers (KC) at Broomfield, Colorado, USA and polypropylene resin carriers (RC) at Fukuoka, Japan, while MBBR WRRFs used KC carriers at South Adams County, Colorado, USA and sponge carriers (SC) at Saga, Japan. Influent COD to N ratios ranged from 8:1 to 15:1. The COD and BOD removal efficiencies were high (96%–98%); NH₄⁺-N and TN removal efficiencies were more varied at 72%–98% and 64%–77%, respectively. The extent of TN removal was higher at high SRT, high COD:N ratio and low DO concentration in the anoxic tank. In IFAS, RC with high specific surface area (SSA) maintained higher AOB population than KC. Sponge carriers with high SSA maintained higher overall bacteria population than KC in MBBR systems. However, the DNB were not more abundant in high SSA carriers. The diversity of AOB, NOB, and DNB was fairly similar in different carriers. Nitrosomonas sp. dominated over Nitrosospira sp. while denitrifying bacteria included Rhodobacter sp., Sulfuritalea sp., Rubrivivax sp., Paracoccus sp., and Pseudomonas sp. The results from this work suggest that high SRT, high COD:N ratio, low DO concentration in anoxic tanks, and carriers with greater surface area may be recommended for high COD, BOD and TN removal in WRRFs with IFAS and MBBR systems.     

The performance of nitrate-reducing Fe(II) oxidation processes under variable initial Fe/N ratios: The fate of nitrogen and iron species

•Bacterially-mediated coupled N and Fe processes examined in incubation experiments. •NO₃⁻ reduction was considerably inhibited as initial Fe/N ratio increased. •The maximum production of N₂ occurred at an initial Fe/N molar ratio of 6. •Fe minerals produced at Fe/N ratios of 1–2 were mainly easily reducible oxides. The Fe/N ratio is an important control on nitrate-reducing Fe(II) oxidation processes that occur both in the aquatic environment and in wastewater treatment systems. The response of nitrate reduction, Fe oxidation, and mineral production to different initial Fe/N molar ratios in the presence of Paracoccus denitrificans was investigated in 132 h incubation experiments. A decrease in the nitrate reduction rate at 12 h occurred as the Fe/N ratio increased. Accumulated nitrite concentration at Fe/N ratios of 2–10 peaked at 12–84 h, and then decreased continuously to less than 0.1 mmol/L at the end of incubation. N₂O emission was promoted by high Fe/N ratios. Maximum production of N₂ occurred at a Fe/N ratio of 6, in parallel with the highest mole proportion of N₂ resulting from the reduction of nitrate (81.2%). XRD analysis and sequential extraction demonstrated that the main Fe minerals obtained from Fe(II) oxidation were easily reducible oxides such as ferrihydrite (at Fe/N ratios of 1–2), and easily reducible oxides and reducible oxides (at Fe/N ratios of 3–10). The results suggest that Fe/N ratio potentially plays a critical role in regulating N₂, N₂O emissions and Fe mineral formation in nitrate-reducing Fe(II) oxidation processes.     

Simultaneous Feammox and anammox process facilitated by activated carbon as an electron shuttle for autotrophic biological nitrogen removal

• The autotrophic nitrogen removal combining Feammox and Anammox was achieved. • Activated carbon can be used as an electron shuttle to enhance Feammox activity. • Fe(III) was reduced to Fe(II) and the secondary Fe(II) mineral (FeOOH) was obtained. • The iron-reducing bacteria and Anammox consortium was enriched simultaneously. Ferric iron reduction coupled with anaerobic ammonium oxidation (Feammox) is a novel ferric-dependent autotrophic process for biological nitrogen removal (BNR) that has attracted increasing attention due to its low organic carbon requirement. However, extracellular electron transfer limits the nitrogen transformation rate. In this study, activated carbon (AC) was used as an electron shuttle and added into an integrated autotrophic BNR system consisting of Feammox and anammox processes. The nitrogen removal performance, nitrogen transformation pathways and microbial communities were investigated during 194 days of operation. During the stable operational period (days 126–194), the total nitrogen (TN) removal efficiency reached 82.9%±6.8% with a nitrogen removal rate of 0.46±0.04 kg-TN/m³/d. The contributions of the Feammox, anammox and heterotrophic denitrification pathways to TN loss accounted for 7.5%, 89.5% and 3.0%, respectively. Batch experiments showed that AC was more effective in accelerating the Feammox rate than the anammox rate. X-ray photoelectron spectroscopy (XPS) analyses showed the presence of ferric iron (Fe(III)) and ferrous iron (Fe(II)) in secondary minerals. X-ray diffraction (XRD) patterns indicated that secondary iron species were formed on the surface of iron-AC carrier (Fe/AC), and Fe(III) was primarily reduced by ammonium in the Feammox process. The phyla Anaerolineaceae (0.542%) and Candidatus Magasanikbacteria (0.147%) might contribute to the Feammox process, and Candidatus Jettenia (2.10%) and Candidatus Brocadia (1.18%) were the dominative anammox phyla in the bioreactor. Overall, the addition of AC provided an effective way to enhance the autotrophic BNR process by integrating Feammox and anammox.     

Preparation of nZVI embedded modified mesoporous carbon for catalytic persulfate to degradation of reactive black 5

• The MCNZVI is prepared as an interesting material for PS activation. • Graphitized carbon shells facilitate electron transfer from Fe⁰. • The MCNZVI exhibits excellent performance to degrade RB5 by ¹O₂. • The MCNZVI has high stability and reusability in the oxidation system. High-efficiency and cost-effective catalysts with available strategies for persulfate (PS) activation are critical for the complete mineralization of organic contaminants in the environmental remediation and protection fields. A nanoscale zero-valent iron-embedded modified mesoporous carbon (MCNZVI) with a core-shell structure is synthesized using the hydrothermal synthesis method and high-temperature pyrolysis. The results showed that nZVI could be impregnated within mesoporous carbon frameworks with a comparatively high graphitization degree, rich nitrogen doping content, and a large surface area and pore volume. This material was used as a persulfate activator for the oxidation removal of Reactive Black 5 (RB5). The effects of the material dosage, PS concentration, pH, and some inorganic anions (i.e., Cl⁻, SO₄²⁻) on RB5 degradation were then investigated. The highest degradation efficiency (97.3%) of RB5 was achieved via PS (20 mmol/L) activation by the MCNZVI (0.5 g/L). The pseudo-first-order kinetics (k = 2.11 × 10⁻² min⁻¹) in the MCNZVI/PS (0.5 g/L, 20 mmol/L) was greater than 100 times than that in the MCNZVI and PS. The reactive oxygen species (ROS), including ¹O₂, SO₄^·−, HO^·, and ·O₂⁻, were generated by PS activation with the MCNZVI. Singlet oxygen was demonstrated to be the primary ROS responsible for the RB5 degradation. The MCNZVI could be reused and regenerated for recycling. This work provides new insights into PS activation to remove organic contamination.     

Ammonia and phosphorus removal from agricultural runoff using cash crop waste-derived biochars

• Orange tree residuals biochar had a better ability to adsorb ammonia. • Modified tea tree residuals biochar had a stronger ability to remove phosphorus. • Partially-modified biochar could remove ammonia and phosphorus at the same time. • The real runoff experiment showed an ammonia nitrogen removal rate of about 80%. • The removal rate of total phosphorus in real runoff experiment was about 95%. Adsorption of biochars (BC) produced from cash crop residuals is an economical and practical technology for removing nutrients from agricultural runoff. In this study, BC made of orange tree trunks and tea tree twigs from the Laoguanhe Basin were produced and modified by aluminum chloride (Al-modified) and ferric sulfate solutions (Fe-modified) under various pyrolysis temperatures (200°C–600°C) and residence times (2–5 h). All produced and modified BC were further analyzed for their abilities to adsorb ammonia and phosphorus with initial concentrations of 10–40 mg/L and 4–12 mg/L, respectively. Fe-modified Tea Tree BC 2h/400°C showed the highest phosphorus adsorption capacity of 0.56 mg/g. Al-modified Orange Tree BC 3h/500°C showed the best performance for ammonia removal with an adsorption capacity of 1.72 mg/g. FTIR characterization showed that P = O bonds were formed after the adsorption of phosphorus by modified BC, N-H bonds were formed after ammonia adsorption. XPS analysis revealed that the key process of ammonia adsorption was the ion exchange between K⁺ and NH₄⁺. Phosphorus adsorption was related to oxidation and interaction between PO₄^3– and Fe³⁺. According to XRD results, ammonia was found in the form of potassium amide, while phosphorus was found in the form of iron hydrogen phosphates. The sorption isotherms showed that the Freundlich equation fits better for phosphorus adsorption, while the Langmuir equation fits better for ammonia adsorption. The simulated runoff infiltration experiment showed that 97.3% of ammonia was removed by Al-modified Orange tree BC 3h/500°C, and 92.9% of phosphorus was removed by Fe-modified Tea tree BC 2h/400°C.     

Insights into simultaneous anammox and denitrification system with short-term pyridine exposure: Process capability,inhibition kinetics and metabolic pathways

• Short-term effect of the pyridine exposure on the SAD process was investigated. • The SAA at 150 mg/L pyridine reduced by 56.7% of the maximum value. • Inhibition kinetics models and inhibitory parameters were indicated. • Collaboration of AnAOB, HDB and PDB promoted the SAD. • Possible metabolic pathways of nitrogen and pyridine were proposed. In-depth knowledge on the role of pyridine as a bottleneck restricting the successful application of anammox-based process treating refractory coking wastewater remains unknown. In this study, the effect of short-term pyridine addition on a simultaneous anammox and denitrification (SAD) system fed with 25–150 mg/L pyridine was explored. The short-term operation showed that the highest total nitrogen (TN) removal efficiency was achieved at 25–50 mg/L of pyridine. As the pyridine addition increased, the contribution of the anammox pathway in nitrogen removal decreased from 99.3% to 79.1%, while the denitrification capability gradually improved. The specific anammox activity (SAA) at 150 mg/L pyridine decreased by 56.7% of the maximum SAA. The modified non-competitive inhibition model indicated that the 50% inhibitory concentration (IC₅₀) of pyridine on anammox was 84.18 mg/L and the substrate inhibition constant (K_i) of pyridine for self-degradation was 135.19 mg/L according to the Haldane model. Moreover, high-throughput sequencing confirmed the abundance of Candidatus Kuenenia as the amount of anammox species decreased, while the amounts of denitrifiers and pyridine degraders significantly increased as the pyridine stress increased. Finally, the possible pathways of nitrogen bioconversion and pyridine biodegradation in the SAD system were elucidated through metagenomic analysis and gas chromatography/mass spectrometry results. The findings of this study enlarge the understanding of the removal mechanisms of complex nitrogenous pyridine-containing wastewater treated by the SAD process.     

The combined effects of biomass and temperature on maximum specific ammonia oxidation rate in domestic wastewater treatment

• Actual SAORs was determined using MLVSS and temperature. • Measured SAOR decreased with increasing MLVSS 1.1‒8.7 g/L. • Temperature coefficient (θ) decreased with increasing MLVSS. • Nitrification process was dynamically simulated based on laboratory-scale SBR tests. • A modified model was successfully validated in pilot-scale SBR systems. Measurement and predicted variations of ammonia oxidation rate (AOR) are critical for the optimization of biological nitrogen removal, however, it is difficult to predict accurate AOR based on current models. In this study, a modified model was developed to predict AOR based on laboratory-scale tests and verified through pilot-scale tests. In biological nitrogen removal reactors, the specific ammonia oxidation rate (SAOR) was affected by both mixed liquor volatile suspended solids (MLVSS) concentration and temperature. When MLVSS increased 1.6, 4.2, and 7.1-fold (1.3‒8.9 g/L, at 20°C), the measured SAOR decreased by 21%, 49%, and 56%, respectively. Thereby, the estimated SAOR was suggested to modify when MLVSS changed through a power equation fitting. In addition, temperature coefficient (θ) was modified based on MLVSS concentration. These results suggested that the prediction of variations ammonia oxidation rate in real wastewater treatment system could be more accurate when considering the effect of MLVSS variations on SAOR.