Deciphering the effect of sodium dodecylbenzene sulfonate on up-flow anaerobic sludge blanket treatment of synthetic sulfate-containing wastewater

• UASB reactor can work efficiently with high COD/SO₄^2- ratios when SDBS exists. • Outcome of the competition between SRB and MPA was affected by SDBS. • Presence of SDBS makes methanogens with H₂/CO₂ as a substrate dominant. • Microbial diversity decreases in the presence of SDBS. In this study, the effects of organic sulfur on anaerobic biological processes were investigated by operating two up-flow anaerobic sludge blanket (UASB) reactors with sodium dodecylbenzene sulfonate (SDBS) as a representative of organic sulfur. The results indicated that the specific methanogenic activity (SMA) and chemical oxygen demand (COD) removal efficiency of R2 (with SDBS added) were higher than those of R1 (without SDBS) when the COD/SO₄²⁻ ratio was above 5.0. However, when the COD/SO₄²⁻ ratio was lower than 5.0, the sulfate reduction efficiency of R2 was higher than that of R1. These results and the observed SDBS transformation efficiency in anaerobic reactors indicate that low concentrations of SDBS accelerate methane production and the continuous accumulation of SDBS does not weaken the reduction of sulfate. Similarly, the calculated electron flux for a COD/SO₄²⁻ ratio of 1.0 indicates that the utilization intensity of electrons by sulfate-reducing bacteria (SRB) in R2 was 36.48% higher than that of SRB in R1 and exceeded that of methane-producing archaea (MPA) under identical working conditions. Moreover, the addition of SDBS in R2 made sulfidogenesis the dominant reaction at low COD/SO₄²⁻, and Methanobacterium and Methanobrevibacter with H₂/CO₂ as the substrate and Desulfomicrobium were the dominant MPA and SRB, respectively. However, methanogenesis was still the dominant reaction in R1, and Methanosaeta with acetic acid as the substrate and Desulfovibrio were the dominant MPA and SRB, respectively.     

The combined effects of biomass and temperature on maximum specific ammonia oxidation rate in domestic wastewater treatment

• Actual SAORs was determined using MLVSS and temperature. • Measured SAOR decreased with increasing MLVSS 1.1‒8.7 g/L. • Temperature coefficient (θ) decreased with increasing MLVSS. • Nitrification process was dynamically simulated based on laboratory-scale SBR tests. • A modified model was successfully validated in pilot-scale SBR systems. Measurement and predicted variations of ammonia oxidation rate (AOR) are critical for the optimization of biological nitrogen removal, however, it is difficult to predict accurate AOR based on current models. In this study, a modified model was developed to predict AOR based on laboratory-scale tests and verified through pilot-scale tests. In biological nitrogen removal reactors, the specific ammonia oxidation rate (SAOR) was affected by both mixed liquor volatile suspended solids (MLVSS) concentration and temperature. When MLVSS increased 1.6, 4.2, and 7.1-fold (1.3‒8.9 g/L, at 20°C), the measured SAOR decreased by 21%, 49%, and 56%, respectively. Thereby, the estimated SAOR was suggested to modify when MLVSS changed through a power equation fitting. In addition, temperature coefficient (θ) was modified based on MLVSS concentration. These results suggested that the prediction of variations ammonia oxidation rate in real wastewater treatment system could be more accurate when considering the effect of MLVSS variations on SAOR.     

Wastewater treatment meets artificial photosynthesis: Solar to green fuel production,water remediation and carbon emission reduction

• Mitigating energy utilization and carbon emission is urgent for wastewater treatment. • MPEC integrates both solar energy storage and wastewater organics removal. • Energy self-sustaining MPEC allows to mitigate the fossil carbon emission. • MPEC is able to convert CO₂ into storable carbon fuel using renewable energy. • MPEC would inspire photoelectrochemistry by employing a novel oxidation reaction. Current wastewater treatment (WWT) is energy-intensive and leads to vast CO₂ emissions. Chinese pledge of “double carbon” target encourages a paradigm shift from fossil fuels use to renewable energy harvesting during WWT. In this context, hybrid microbial photoelectrochemical (MPEC) system integrating microbial electrochemical WWT with artificial photosynthesis (APS) emerges as a promising approach to tackle water-energy-carbon challenges simultaneously. Herein, we emphasized the significance to implement energy recovery during WWT for achieving the carbon neutrality goal. Then, we elucidated the working principle of MPEC and its advantages compared with conventional APS, and discussed its potential in fulfilling energy self-sustaining WWT, carbon capture and solar fuel production. Finally, we provided a strategy to judge the carbon profit by analysis of energy and carbon fluxes in a MPEC using several common organics in wastewater. Overall, MPEC provides an alternative of WWT approach to assist carbon-neutral goal, and simultaneously achieves solar harvesting, conversion and storage.     

Removal of steroid hormones from mariculture system using seaweed Caulerpa lentillifera

•Steroid hormones could be removed efficiently from mariculture system using seaweed; • Caulerpa lentillifera was the most efficient seaweed for removal of steroid hormones; • More than 90% of E₂ or EE₂ were removed within 12 h using Caulerpa lentillifera; • The removal included the rapid biosorption and the slow bio-accumulation; •The hormones and nutrients in mariculture wastewater could be simultaneously removed. The removal of steroid hormones from the mariculture system using seaweeds (Caulerpa lentillifera, Ulva pertusa, Gracilaria lemaneiformis, and Codium fragile) was investigated. The results illustrated that both 17β-estradiol (E₂) and 17α-ethinylestradiol (EE₂) could be removed by the seaweeds at different levels, and the Caulerpa lentillifera was the most efficient one. More than 90% of E₂ or EE₂ at concentration of 10 μg/L was removed by Caulerpa lentillifera within 12 h. Processes including initial quick biosorption, the following slow accumulation, and biodegradation might explain the removal mechanisms of E₂/EE₂ by Caulerpa lentillifera. E₂/EE₂ removal was positively related to the nutrient level and the initial concentration of steroid hormone. A significant linear relationship for E₂ and EE₂ existed between the initial pollutant concentration and the average removal rate. The highest removal kinetic constant (k) value was obtained at 30°C as 0.34 /h for E₂ and at 20°C as 0.28 /h for EE₂, demonstrating the promising application potential of Caulerpa lentillifera in the water purification of the industrialized mariculture system with relatively high water temperature. Simultaneous and efficient removal of E₂ and EE₂ by Caulerpa lentillifera was still achieved after 3 cycles in the pilot-scale experiment. The steroid hormones and nutrients in mariculture wastewater could also be simultaneously removed using Caulerpa lentillifera. These findings demonstrated that Caulerpa lentillifera was the promising seaweed for the removal of steroid hormones in mariculture systems.     

Cattle manure biochar and earthworm interactively affected CO2 and N2O emissions in agricultural and forest soils: Observation of a distinct difference

• Earthworms increase CO₂ and N₂O emissions in agricultural and forest soil. • 10% biochar suppresses CO₂ and N₂O emissions in forest soil. • Biochar interacted with earthworm to significant affect CO₂ and N₂O emissions. The application of manure-derived biochar offers an alternative to avoid the direct application of manure to soil causing greenhouse gas emission. Soil fauna, especially earthworms, can markedly stimulate carbon dioxide (CO₂) and nitrous oxide (N₂O) emissions from soil. This study therefore investigated the effect of cattle manure biochar (added at rates of 0, 2%, or 10%, coded as BC0, BC2 and BC10, respectively) application, with or without earthworm Aporrectodea turgida, on emissions of CO₂ and N₂O and changes of physic-chemical properties of agricultural and forest soils in a laboratory incubation experiment. The BC10 treatment significantly enhanced cumulative CO₂ emissions by 27.9% relative to the untreated control in the agricultural soil. On the contrary, the BC2 and BC10 treatments significantly reduced cumulative CO₂ emissions by 16.3%–61.1% and N₂O emissions by 92.9%–95.1% compared to the untreated control in the forest soil. The addition of earthworm alone significantly enhanced the cumulative CO₂ and N₂O fluxes in agricultural and forest soils. Cumulative CO₂ and N₂O fluxes were significantly increased when BC2 and BC10 were applied with earthworm in the agricultural soil, but were significantly reduced when BC10 was applied with earthworm in the forest soil. Our study demonstrated that biochar application interacted with earthworm to affect CO₂ and N₂O emissions, which were also dependent on the soil type involved. Our study suggests that manure biochar application rate and use of earthworm need to be carefully studied for specific soil types to maximize the climate change mitigation potential of such management practices.     

Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

Mechanism of dichloromethane disproportionation over mesoporous TiO2 under low temperature

• Mechanism of DCM disproportionation over mesoporous TiO₂ was studied. • DCM was completely eliminated at 350℃ under 1 vol.% humidity. • Anatase (001) was the key for disproportionation. • A competitive oxidation route co-existed with disproportionation. • Disproportionation was favored at low temperature. Mesoporous TiO₂ was synthesized via nonhydrolytic template-mediated sol-gel route. Catalytic degradation performance upon dichloromethane over as-prepared mesoporous TiO₂, pure anatase and rutile were investigated respectively. Disproportionation took place over as-made mesoporous TiO₂ and pure anatase under the presence of water. The mechanism of disproportionation was studied by in situ FTIR. The interaction between chloromethoxy species and bridge coordinated methylenes was the key step of disproportionation. Formate species and methoxy groups would be formed and further turned into carbon monoxide and methyl chloride. Anatase (001) played an important role for disproportionation in that water could be dissociated into surface hydroxyl groups on such structure. As a result, the consumed hydroxyl groups would be replenished. In addition, there was another competitive oxidation route governed by free hydroxyl radicals. In this route, chloromethoxy groups would be oxidized into formate species by hydroxyl radicals transfering from the surface of TiO₂. The latter route would be more favorable at higher temperature.     

Size and shape effects of MnFe2O4 nanoparticles as catalysts for reductive degradation of dye pollutants

• Size and shape-dependent MnFe₂O₄ NPs were prepared via a facile method. • Ligand-exchange chemistry was used to prepare the hydrophilic MnFe₂O₄ NPs. • The catalytic properties of MnFe₂O₄ NPs toward dye degradation were fully studied. • The catalytic activities of MnFe₂O₄ NPs followed Michaelis–Menten behavior. • All the MnFe₂O₄ NPs exhibit selective degradation to different dyes. The magnetic nanoparticles that are easy to recycle have tremendous potential as a suitable catalyst for environmental toxic dye pollutant degradation. Rationally engineering shapes and tailoring the size of nanocatalysts are regarded as an effective manner for enhancing performances. Herein, we successfully synthesized three kinds of MnFe₂O₄ NPs with distinctive sizes and shapes as catalysts for reductive degradation of methylene blue, rhodamine 6G, rhodamine B, and methylene orange. It was found that the catalytic activities were dependent on the size and shape of the MnFe₂O₄ NPs and highly related to the surface-to-volume ratio and atom arrangements. Besides, all these nanocatalysts exhibit selectivity to different organic dyes, which is beneficial for their practical application in dye pollutant treatment. Furthermore, the MnFe₂O₄ NPs could be readily recovered by a magnet and reused more than ten times without appreciable loss of activity. The size and shape effects of MnFe₂O₄ nanoparticles demonstrated in this work not only accelerate further understanding the nature of nanocatalysts but also contribute to the precise design of nanoparticles catalyst for pollutant degradation.     

Understanding the role of nano-TiO2 on the toxicity of Pb on C. dubia through modeling–Is it additive or synergistic?

• A two-compartment model is able to quantify the effect of nano-TiO₂ on Pb toxicity. • Nano-TiO₂ reduces Pb tolerance level and increased the killing rate for C. dubia. • Thus, nano-TiO₂ synergistically enhances Pb toxicity. • Algae reduce Pb transfer rate to the body tissue and the killing rate. Nano-TiO₂ can remarkably increase lead (Pb) toxicity in aquatic organisms. However, the mechanism of this toxicity, additive or synergistic, is not well understood. To explore this mechanism, we inspected the role of nano-TiO₂ in the toxicity of Pb on Ceriodaphnia dubia (C. dubia), a model water flea species typically used for ecotoxicity studies. The effect of algae, a diet for aquatic organisms, on the effect of this binary mixture was also investigated. A two-compartment toxicokinetic (TK)-toxicodynamic (TD) modeling approach was used to quantify the Pb toxicity under these complex conditions and to develop critical parameters for understanding the mechanism of toxicity. This two-compartment modeling approach adequately described the Pb accumulation in the gut and in the rest of the body tissue under different nano-TiO₂ concentrations, with and without algae, and predicted the toxicity response of C. dubia. It indicated that increasing the nano-TiO₂ concentration reduced the Pb tolerance level and concurrently increased the killing rate constant of C. dubia. Therefore, nano-TiO₂ synergistically enhanced Pb toxicity. Algae remarkably reduced the toxicity of this binary mixture through reducing the Pb transfer rate to the body tissue and the killing rate, although it did not affect the Pb tolerance level. This two-compartment modeling approach is useful in understanding the role of nanoparticles when assessing the overall toxicity of nanoparticles and other toxic elements in the environment.     

Experimental and computational assessment of 1,4-Dioxane degradation in a photo-Fenton reactive ceramic membrane filtration process

• 1,4-Dioxane was degraded via the photo-Fenton reactive membrane filtration. • Degradation efficiency and AQY were both enhanced in photocatalytic membrane. • There is a tradeoff between photocatalytic degradation and membrane permeation flux. • Degradation pathways of 1,4-Dioxane is revealed by DFT analysis. The present study evaluated a photo-Fenton reactive membrane that achieved enhanced 1,4-Dioxane removal performance. As a common organic solvent and stabilizer, 1,4-Dioxane is widely used in a variety of industrial products and poses negative environmental and health impacts. The membrane was prepared by covalently coating photocatalyst of goethite (α-FeOOH) on a ceramic porous membrane as we reported previously. The effects of UV irradiation, H₂O₂ and catalyst on the removal efficiency of 1,4-Dioxane in batch reactors were first evaluated for optimized reaction conditions, followed by a systematical investigation of 1,4-Dioxane removal in the photo-Fenton membrane filtration mode. Under optimized conditions, the 1,4-Dioxane removal rate reached up to 16% with combination of 2 mmol/L H₂O₂ and UV₃₆₅ irradiation (2000 µW/cm²) when the feed water was filtered by the photo-Fenton reactive membrane at a hydraulic retention time of 6 min. The removal efficiency and apparent quantum yield (AQY) were both enhanced in the filtration compared to the batch mode of the same photo-Fenton reaction. Moreover, the proposed degradation pathways were analyzed by density functional theory (DFT) calculations, which provided a new insight into the degradation mechanisms of 1,4-Dioxane in photo-Fenton reactions on the functionalized ceramic membrane.     

A novel strategy for gas mitigation during swine manure odour treatment using seaweed and a microbial consortium

• Comprehensive mitigation of gas emissions from swine manure was investigated. • Additives addition for mitigation of gas from the manure has been developed. • Sargassum horneri, seaweed masking strategy controlled gas by 90%-100%. • Immediate reduction in emitted gas and improving air quality has been determined. • Microbial consortium with seaweed completely controlled gas emissions by 100%. Gas emissions from swine farms have an impact on air quality in the Republic of Korea. Swine manure stored in deep pits for a long time is a major source of harmful gas emissions. Therefore, we evaluated the mitigation of emissions of ammonia (NH₃), hydrogen sulfide (H₂S) and amine gases from swine manure with biological products such as seaweed (Sargassum horneri) and a microbial consortium (Bacillus subtilis (1.2 × 10⁹ CFU/mL), Thiobacillus sp. (1.0 × 10¹⁰ CFU/mL) and Saccharomyces cerevisiae (2.0 × 10⁹ CFU/mL)) used as additives due to their promising benefits for nutrient cycling. Overall, seaweed powder masking over two days provided notable control of over 98%-100% of the gas emissions. Furthermore, significant control of gas emissions was especially pronounced when seaweed powder masking along with a microbial consortium was applied, resulting in a gas reduction rate of 100% for NH₃, amines and H₂S over 10 days of treatment. The results also suggested that seaweed powder masking and a microbial consortium used in combination to reduce the gas emissions from swine manure reduced odour compared with that observed when the two additives were used alone. Without the consortium, seaweed decreased total volatile fatty acid (VFA) production. The proposed novel method of masking with a microbial consortium is promising for mitigating hazardous gases, simple, and environmentally beneficial. More research is warranted to determine the mechanisms underlying the seaweed and substrate interactions.     

Visible-light-driven heterostructured g-C3N4/Bi-TiO2 floating photocatalyst with enhanced charge carrier separation for photocatalytic inactivation of Microcystis aeruginosa

• Bi doping in TiO₂ enhanced the separation of photo-generated electron-hole. • The performance of photocatalytic degradation of MC-LR was improved. • Coexisting substances have no influence on algal removal performance. • The key reactive oxygen species were h⁺ and ^•OH in the photocatalytic process. The increase in occurrence and severity of cyanobacteria blooms is causing increasing concern; moreover, human and animal health is affected by the toxic effects of Microcystin-LR released into the water. In this paper, a floating photocatalyst for the photocatalytic inactivation of the harmful algae Microcystis aeruginosa (M. aeruginosa) was prepared using a simple sol-gel method, i.e., coating g-C₃N₄ coupled with Bi-doped TiO₂ on Al₂O₃-modified expanded perlite (CBTA for short). The impact of different molar ratios of Bi/Ti on CBTA was considered. The results indicated that Bi doping in TiO₂ inhibited photogenerated electron-hole pair recombination. With 6 h of visible light illumination, 75.9% of M. aeruginosa (initial concentration= 2.7 × 10⁶ cells/L) and 83.7% of Microcystin-LR (initial concentration= 100 μg/L) could be removed with the addition of 2 g/L CBTA-1% (i.e., Bi/Ti molar ratio= 1%). The key reactive oxygen species (ROSs) in the photocatalytic inactivation process are h⁺ and ^•OH. The induction of the Bi⁴⁺/Bi³⁺ species by the incorporation of Bi could narrow the bandgap of TiO₂, trap electrons, and enhance the stability of CBTA-1% in the solutions with coexisting environmental substances.     

Electricity-driven ammonia oxidation and acetate production in microbial electrosynthesis systems

• MES was constructed for simultaneous ammonia removal and acetate production. • Energy consumption was different for total nitrogen and ammonia nitrogen removal. • Energy consumption for acetate production was about 0.04 kWh/g. • Nitrate accumulation explained the difference of energy consumption. • Transport of ammonia and acetate across the membrane deteriorated the performance. Microbial electrosynthesis (MES) is an emerging technology for producing chemicals, and coupling MES to anodic waste oxidation can simultaneously increase the competitiveness and allow additional functions to be explored. In this study, MES was used for the simultaneous removal of ammonia from synthetic urine and production of acetate from CO₂. Using graphite anode, 83.2%±5.3% ammonia removal and 28.4%±9.9% total nitrogen removal was achieved, with an energy consumption of 1.32 kWh/g N for total nitrogen removal, 0.45 kWh/g N for ammonia nitrogen removal, and 0.044 kWh/g for acetate production. Using boron-doped diamond (BDD) anode, 70.9%±12.1% ammonia removal and 51.5%±11.8% total nitrogen removal was obtained, with an energy consumption of 0.84 kWh/g N for total nitrogen removal, 0.61 kWh/g N for ammonia nitrogen removal, and 0.043 kWh/g for acetate production. A difference in nitrate accumulation explained the difference of total nitrogen removal efficiencies. Transport of ammonia and acetate across the membrane deteriorated the performance of MES. These results are important for the development of novel electricity-driven technologies for chemical production and pollution removal.     

Bioaerosolization behavior along sewage sludge biostabilization

• Aerosolization behavior during a lab-scale sludge biostabilization was determined. • Many pathogenic species were identified to be preferentially aerosolized. • Bioaerosol concentration along the biostabilization ranged from 160 to 1440 cell/m³. • Sludge aerosolization behavior was different with that of other biowaste. Biostabilization is a cost-effective method for the beneficial utilization of sewage sludge. However, during the operation of sludge biostabilization, some microbial species could be released into the atmospheric environment from the solid-phase of sludge easily and present a high risk to human health. This study aimed to evaluate the risk of bioaerosol during sludge biostabilization. We found a total of nine bacterial phyla, one archaeal phylum, and two fungal phyla in the bioaerosol samples. Among them, Proteobacteria, Actinobacteria, Bacteroidetes, and Ascomycota were the dominant phyla. In addition, the bioaerosolization indexes (BI) of prokaryotic phyla and fungal phyla ranged 0–45 and 0–487, respectively. Massilia, Pseudarthrobacter, Pseudomonas, Tremellales spp., and Fusarium were the preferentially aerosolized microbial genera with maximum bioaerosolization indexes of 19962, 10360, 1802, 3055, and 7398. The bioaerosol concentration during the biostabilization ranged from 160 to 1440 cell/m³, and we identified species such as Stenotrophomonas rhizophila and Fusarium graminerum with high bioaerosolization indexes that could be threats to human health. Euryachaeota, which belongs to archaeal phyla, had the highest biostabilization index in our study. We also found that Pseudarthrobacter was the easiest to aerosolize during the sludge biostabilization process.     

Acid Orange 7 degradation using methane as the sole carbon source and electron donor

• AO7 degradation was coupled with anaerobic methane oxidation. • Higher concentration of AO7 inhibited the degradation. • The maximum removal rate of AO7 reached 280 mg/(L·d) in HfMBR. • ANME-2d dominated the microbial community in both batch reactor and HfMBR. • ANME-2d alone or synergistic with the partner bacteria played a significant role. Azo dyes are widely applied in the textile industry but are not entirely consumed during the dyeing process and can thus be discharged to the environment in wastewater. However, azo dyes can be degraded using various electron donors, and in this paper, Acid Orange 7 (AO7) degradation performance is investigated using methane (CH₄) as the sole electron donor. Methane has multiple sources and is readily available and inexpensive. Experiments using ¹³C-labeled isotopes showed that AO7 degradation was coupled with anaerobic oxidation of methane (AOM) and, subsequently, affected by the initial concentrations of AO7. Higher concentrations of AO7 could inhibit the activity of microorganisms, which was confirmed by the long-term performance of AO7 degradation, with maximum removal rates of 8.94 mg/(L·d) in a batch reactor and 280 mg/(L·d) in a hollow fiber membrane bioreactor (HfMBR). High-throughput sequencing using 16S rRNA genes showed that Candidatus Methanoperedens, affiliated to ANME-2d, dominated the microbial community in the batch reactor and HfMBR. Additionally, the relative abundance of Proteobacteria bacteria (Phenylobacterium, Pseudomonas, and Geothermobacter) improved after AO7 degradation. This outcome suggested that ANME-2d alone, or acting synergistically with partner bacteria, played a key role in the process of AO7 degradation coupled with AOM.     

Simultaneous removal of NOx and chlorobenzene on V2O5/TiO2 granular catalyst: Kinetic study and performance prediction

• A V₂O₅/TiO₂ granular catalyst for simultaneous removal of NO and chlorobenzene. • Catalyst synthesized by vanadyl acetylacetonate showed good activity and stability. • The kinetic model was established and the synergetic activity was predicted. • Both chlorobenzene oxidation and SCR of NO follow pseudo-first-order kinetics. • The work is of much value to design of multi-pollutants emission control system. The synergetic abatement of multi-pollutants is one of the development trends of flue gas pollution control technology, which is still in the initial stage and facing many challenges. We developed a V₂O₅/TiO₂ granular catalyst and established the kinetic model for the simultaneous removal of NO and chlorobenzene (i.e., an important precursor of dioxins). The granular catalyst synthesized using vanadyl acetylacetonate precursor showed good synergistic catalytic performance and stability. Although the SCR reaction of NO and the oxidation reaction of chlorobenzene mutually inhibited, the reaction order of each reaction was not considerably affected, and the pseudo-first-order reaction kinetics was still followed. The performance prediction of this work is of much value to the understanding and reasonable design of a catalytic system for multi-pollutants (i.e., NO and dioxins) emission control.     

Assessing combined toxic effects of tetracycline and P25 titanium dioxide nanoparticles using Allium cepa bioassay

• UVA pre-irradiation to TiO₂ NPs enhanced its toxicity toward plant A. cepa. • UVA TiO₂ NPs increased intracellular ROS, resulting in more cell damage. • Cell death enhanced cell permeability and increased uptake of NPs. • Being highly toxic (EC₅₀ = 0.097 µmol/L), TC did not increase ROS generation. • Even at a low dose, TC enhanced the toxic potential of TiO₂ NPs significantly. Usage of titanium dioxide nanoparticles (TiO₂ NPs) and tetracycline (TC) has increased significantly in the present era. This leads to their release and accumulation in the environment. Both the compounds, individually, can have adverse toxic effects on the plants. Their binary mixtures can increase this degree of damage. The present study aimed to evaluate the toxicity of both the contaminants in individual and binary mixtures in Allium cepa. Further, the toxicity of TiO₂ NPs upon UVA pre-irradiation was also measured. Results showed that UVA pre-irradiated NPs (UVA-TiO₂ NPs) had a significant decrease in cell viability than their non-irradiated counterparts (NI-TiO₂), denoting an increase in photocatalytic activity upon UVA pre-irradiation. Very low concentrations of TC (EC₁₀ = 0.016 µmol/L) mixed with TiO₂ NPs significantly increased the toxicity for both UVA-TiO₂ and NI-TiO₂ NPs. Intracellular ROS generation was significantly high for UVA-TiO₂ NPs. However, TC did not have any effects on ROS production. Both the compounds exhibited genotoxic potential in A. cepa. Different chromosomal abnormalities like anaphase bridges, telophase bridges, laggard chromosomes, binucleate cells, etc. were observed. The binary mixture of UVA-TiO₂ NPs and TC showed the highest chromosomal aberrations (64.0%±1.26%) than the mixture with NI-TiO₂ or the individual contaminants. This decreased significantly after recovery (46.8%±1.92%), denoting the self-repair processes. This study proved that UVA-TiO₂ NPs were more toxic and could be enhanced further when mixed with a sub-lethal concentration of TC. This work will help to assess the risk of both compounds in the environment.     

TiO2@palygorskite composite for the efficient remediation of oil spills via a dispersion-photodegradation synergy

• A novel and multi-functional clay-based oil spill remediation system was constructed. • TiO₂@PAL functions as a particulate dispersant to break oil slick into tiny droplets. • Effective dispersion leads to the direct contact of TiO₂ with oil pollutes directly. • TiO₂ loaded on PAL exhibits efficient photodegradation for oil pollutants. • TiO₂@PAL shows a typical dispersion-photocatalysis synergistic remediation. Removing spilled oil from the water surface is critically important given that oil spill accidents are a common occurrence. In this study, TiO₂@Palygorskite composite prepared by a simple coprecipitation method was used for oil spill remediation via a dispersion-photodegradation synergy. Diesel could be efficiently dispersed into small oil droplets by TiO₂@Palygorskite. These dispersed droplets had an average diameter of 20–30 mm and exhibited good time stability. The tight adsorption of TiO₂@Palygorskite on the surface of the droplets was observed in fluorescence and SEM images. As a particulate dispersant, the direct contact of TiO₂@Palygorskite with oil pollutants effectively enhanced the photodegradation efficiency of TiO₂ for oil. During the photodegradation process, •O₂⁻and •OH were detected by ESR and radical trapping experiments. The photodegradation efficiency of diesel by TiO₂@Palygorskite was enhanced by about 5 times compared with pure TiO₂ under simulated sunlight irradiation. The establishment of this new dispersion-photodegradation synergistic remediation system provides a new direction for the development of marine oil spill remediation.     

Temporal variation of PM2.5-associated health effects in Shijiazhuang,Hebei

•Annual mean PM_2.5 in Shijiazhuang were 87, 95, and 82 µg/m³ in 2015–2017. •Health risk of cardiovascular system was higher than respiratory system. •Premature mortality attributed to PM_2.5 was 5088 people in 2017. •ΔMort and YLL reduced by 84.2% and 84.6% when PM_2.5 reduced to 10 µg/m³. •Health risks due to PM_2.5 were severe in Shijiazhuang in 2015–2017. Shijiazhuang is one of the cities in the North China Plain. In recent decades, this city has experienced high levels of fine particulate matter (PM_2.5), which have potentially significant effects on human health. In this study, the health effects of PM_2.5 exposure in Shijiazhuang were estimated by applying an integrated exposure-response model. Premature mortality, years of life lost (YLL), and the mortality benefits linked to reduced levels of PM_2.5 were quantified for the period 2015–2017. In 2015, 2016, and 2017, cerebrovascular diseases caused the highest premature mortality (2432, 2449, and 2483, respectively), followed by ischemic heart diseases (1391, 1479, and 1493, respectively), lung cancer (639,660, and 639, respectively), and chronic obstructive pulmonary diseases (533, 519, and 473, respectively). Notably, the total number of premature deaths caused by PM_2.5 exposure in Shijiazhuang in 2015, 2016, and 2017 were 4994, 5107, and 5088, respectively. Moreover, the YLL in the same years were 47001, 47880 and 47381, respectively. Interestingly, the YLL per 1000 females was lower than that per 1000 males. Finally, we noted that premature mortality and YLL decreased by 84.2% and 84.6% when the PM_2.5 levels diminished to 10 µg/m³. Overall, the results of this study improve our understanding of how high PM_2.5 concentrations affect human health and suggest the application of more stringent measures in Shijiazhuang to alleviate the associated health risks.