Influence of temperature on PCDD/PCDF desorption from waste incineration flyash under nitrogen

A municipal solid waste incinerator flyash was heated to between 200 and 400 degrees C under nitrogen in a bench-scale, static bed reactor for 4 days soak time. The influence of temperature on the levels of PCDD and PCDF remaining in and desorbed from the ash were investigated using GC-MS/MS. PCDD and especially PCDF formation was seen on the flyash between 225 and 300 degrees C. Large increases in the I-TEQ of the treated ash relative to the increase in its overall PCDD/PCDF content indicated that the formation of 2378-substituted congeners was favoured over that of other substitution patterns. In the absence of a source of gaseous oxygen, formation was mainly attributed to de novo reactions involving solid phase oxygen. Dechlorination of the PCDD/PCDF in flyash became increasingly important above 275 degrees C. Maximum desorption was seen at 325 degrees C, with the equivalent of 35 wt% of the PCDD/F in the original flyash being recovered from the exhaust traps at this temperature. The desorbed species were mainly M(1)CDD/CDDF-T(3)CDD/CDDF resulting from dechlorination of higher chlorinated PCDD/PCDF, with consequently low I-TEQ values.     

PCDD/F formation from oxy-PAH precursors in waste incinerator flyash

The yield of PCDD/F in relation to the presence of oxygenated PAH in model waste incinerator flyash has been investigated in a fixed bed laboratory scale reactor. Experiments were undertaken by thermal treatment of the model flyash at 250 and 350 °C under a simulated flue gas stream for 2 h. After reaction, the PCDD/F content of the reacted flyash and the PCDD/F released into the exhaust gas, and subsequently trapped by XAD-II resin in a down-stream condensation system were analyzed. The PAHs investigated were, dibenzofuran and benzo[b]naphtho[2,3-d]furan and were spiked onto the model flyash as reactant precursors for PCDD/F formation. The results showed significant formation of furans from both of the PAH investigated, however except from some highly chlorinated dioxin congeners, the formation of dioxins was not so common. Benzonaphthofuran was significantly more reactive than dibenzofuran in PCDD/F formation, in spite of the fact that dibenzofuran is structurally more similar to that of PCDD/F. Thus, there was no clear attribution between the chemical structure of PAH used and the formation of PCDD/F. There were considerable differences between the yields of PCDD/F congeners in the gaseous species and those in the reacted flyash under the same operational conditions. The concentration of PCDD/Fs was reduced at the higher reaction temperature of 350 °C; however, the higher temperature resulted in the majority of the PCDD/F formed on the flyash being released into the gas phase.     

PCDD/F formation from oxy-PAH precursors in waste incinerator flyash

The yield of PCDD/F in relation to the presence of oxygenated PAH in model waste incinerator flyash has been investigated in a fixed bed laboratory scale reactor. Experiments were undertaken by thermal treatment of the model flyash at 250 and 350 °C under a simulated flue gas stream for 2 h. After reaction, the PCDD/F content of the reacted flyash and the PCDD/F released into the exhaust gas, and subsequently trapped by XAD-II resin in a down-stream condensation system were analyzed. The PAHs investigated were, dibenzofuran and benzo[b]naphtho[2,3-d]furan and were spiked onto the model flyash as reactant precursors for PCDD/F formation. The results showed significant formation of furans from both of the PAH investigated, however except from some highly chlorinated dioxin congeners, the formation of dioxins was not so common. Benzonaphthofuran was significantly more reactive than dibenzofuran in PCDD/F formation, in spite of the fact that dibenzofuran is structurally more similar to that of PCDD/F. Thus, there was no clear attribution between the chemical structure of PAH used and the formation of PCDD/F. There were considerable differences between the yields of PCDD/F congeners in the gaseous species and those in the reacted flyash under the same operational conditions. The concentration of PCDD/Fs was reduced at the higher reaction temperature of 350 °C; however, the higher temperature resulted in the majority of the PCDD/F formed on the flyash being released into the gas phase.     

PCDD/F enviromental impact from municipal solid waste bio-drying plant

The present work indentifies some environmental and health impacts of a municipal solid waste bio-drying plant taking into account the PCDD/F release into the atmosphere, its concentration at ground level and its deposition. Four scenarios are presented for the process air treatment and management: biofilter or regenerative thermal oxidation treatment, at two different heights. A Gaussian dispersion model, AERMOD, was used in order to model the dispersion and deposition of the PCDD/F emissions into the atmosphere. Considerations on health risk, from different exposure pathways are presented using an original approach. The case of biofilter at ground level resulted the most critical, depending on the low dispersion of the pollutants. Suggestions on technical solutions for the optimization of the impact are presented.     

PCDD/PCDF Isomer patterns in waste incinerator flyash and desorbed into the gas phase in relation to temperature

The influence of temperature on the PCDD and PCDF isomer profiles of a municipal waste incinerator flyash and the PCDD/PCDF desorbed from the ash under an inert atmosphere was investigated using a bench-scale reactor. Exposure to temperatures of 250 degrees C and above resulted in significant changes in the distribution of isomers within most dioxin and furan congener groups. The PCDD content tended to become more evenly distributed across the range of isomers than was the case for the raw flyash, while the PCDF content became concentrated across a relatively lower number of isomers. In most cases the desorbed PCDD/PCDF were mainly mono- to tri-chlorinated, and hence had a relatively low I-TEQ value. The isomer profiles of the desorbed species were also influenced by temperature. There were some significant differences between the PCDF isomer profiles of the desorbed species and those of the treated flyashes under the same conditions, but no clear differences between the PCDD isomer profiles.     

PCDD/PCDF congener profiles in soil and herbage samples collected in the vicinity of a municipal waste incinerator before and after pronounced reductions of PCDD/PCDF emissions from the facility

Congener profiles are the fractional distribution of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) congeners in an environmental release, or in an environmental or biological sample. In 1999, an adaptation to the EU legislation on pollutant emissions from the stack was carried out in an old municipal solid waste incinerator (MSWI) from Montcada (Barcelona, Spain). The main goal of the present study was to determine if the environmental PCDD/F levels in the area under direct influence of the facility were mainly due to PCDD/F emissions from the plant. For this purpose, soil and herbage samples were collected near the MSWI before (1998) and after (2000) the technical improvements were performed. PCDD/F congener profiles were determined and compared with those from samples collected in a suburban area of Constantí (Tarragona, Spain) outside of direct emissions from any MSWI. The results of the present study suggest that the MSWI here assessed is not the main responsible for the environmental PCDD/F concentrations in the area under evaluation. Other PCDD/F emission sources in the same area seem also to have a notable impact on the atmospheric levels of these pollutants.     

Destruction of PCDD/Fs by SCR from flue gases of municipal waste incinerator and metal smelting plant

Partitioning of PCDD/F congeners between vapor/solid phases and removal and destruction efficiencies achieved with selective catalytic reduction (SCR) system for PCDD/Fs at an existing municipal waste incinerator (MWI) and metal smelting plant (MSP) in Taiwan are evaluated via stack sampling and analysis. The MWI investigated is equipped with electrostatic precipitators (EP, operating temperature: 230 degrees C), wet scrubbers (WS, operating temperature: 70 degrees C) and SCR (operating temperature: 220 degrees C) as major air pollution control devices (APCDs). PCDD/F concentration measured at stack gas of the MWI investigated is 0.728 ng-TEQ/Nm(3). The removal efficiency of WS+SCR system for PCDD/Fs reaches 93% in the MWI investigated. The MSP investigated is equipped with EP (operating temperature: 240 degrees C) and SCR (operating temperature: 290 degrees C) as APCDs. The flue gas sampling results also indicate that PCDD/F concentration treated with SCR is 1.35 ng-TEQ/Nm(3). The SCR system adopted in MSP can remove 52.3% PCDD/Fs from flue gases (SCR operating temperature: 290 degrees C, Gas flow rate: 660 kN m(3)/h). In addition, the distributions of PCDD/F congeners observed in the flue gases of the MWI and MSP investigated are significantly different. This study also indicates that the PCDD/F congeners measured in the flue gases of those two facilities are mostly distributed in vapor phase prior to the SCR system and shift to solid phase (vapor-phase PCDD/Fs are effectively decomposed) after being treated with catalyst. Besides, the results also indicate that with SCR highly chlorinated PCDD/F congeners can be transformed to lowly chlorinated PCDD/F congeners probably by dechlorination, while the removal efficiencies of vapor-phase PCDD/Fs increase with increasing chlorination.     

Influence of a municipal solid waste incinerator on ambient air and soil PCDD/Fs levels

To examine the influence of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) emissions from a municipal solid waste incinerator (MSWI) on the environment, we measured the levels of PCDD/Fs in ambient air and soil samples collected near a MSWI in Bucheon, Korea. The PCDD/Fs concentrations in the ambient air samples ranged from 0.22 to 1.16 pg I-TEQm(-3) (13.39-75.16 pg m(-3)), with an average of 0.66 pg I-TEQ m(-3) (35.62 pg m(-3)). The soil samples contained between 1.25 and 74.98 pg I-TEQ g(-1) (38.15-3,303.33 pg g(-1)), with an average of 19.06 pg I-TEQ g(-1) (1,077.11 pg g(-1)). These levels were higher than those previously reported by other investigators in a number of surveys. The furan homologues predominated in the air samples and some soil samples, and the soil PCDD/Fs levels decreased with increasing distance from the MSWI. Comparison of the homologue patterns and a multivariate statistical analysis showed that PCDD/Fs emission from the MSWI directly affected the pattern of PCDD/Fs in air, while the PCDD/Fs patterns in soil differed according to the location relative to the MSWI, roads, and construction sites. These results collectively indicate that the MSWI was the major PCDD/Fs emission source in this area, but that unidentified combustion sources and vehicles might influence the environment to some extent.     

Isomeric analysis of PCDD/PCDF in waste incinerator fly ash by GC-MS/MS

The development of an analytical method for the analysis of PCDD/PCDF in flyash using a bench analytical system comprising of a gas chromatograph fitted with an ion trap detector operated in the tandem MS mode is described. The optimum settings for the most important MS/MS parameters are given, including those for the less reported mono- to tri-chlorinated dioxin and furan congener groups. Flyash samples from three waste incineration plants representing a decommissioned 1970s plant design, an upgraded and still operating plant originally designed in the 1970s, and a modern 1990s design operating plant have been analysed for PCDD/PCDF. The flyash samples were analysed for PCDD/PCDF using the methods developed and the total PCDD/PCDF, I-TEQ values and isomeric profiles are reported. The flyash from the older decommissioned incinerator had very significantly higher concentrations of PCDD/PCDF compared to the modern incinerator flyash.     

PCDD/Fs atmospheric deposition fluxes and soil contamination close to a municipal solid waste incinerator

Bulk depositions and surface soil were collected in a suburban area, near the Adriatic Sea, in order to assess the contribution of a municipal solid waste incinerator to the area’s total contamination with polychlorinated dibenzodioxins and polychlorinated dibenzofurans (PCDDs and PCDFs). Samples were collected at two sites, situated in the area most affected by plant emissions (according to the results of the Calpuff air dispersion model), and at an external site, considered as a reference. Results show that the studied area is subject to low contamination, as far as these compounds are concerned. Deposition fluxes range from 14.3 pg m⁻² d⁻¹ to 89.9 pg m⁻² d⁻¹ (0.75 pg-TEQ m⁻² d⁻¹ to 3.73 pg-TEQ m⁻² d⁻¹) and no significant flow differences are observed among the three monitored sites. Total soil concentration amounts to 93.8 ng kg⁻¹ d.w. and 1.35 ng-TEQ kg⁻¹ d.w, on average, and confirms a strong homogeneity in the studied area. Furthermore, from 2006 to 2009, no PCDD/Fs enrichment in the soil was noticed. Comparing the relative congener distributions in environmental samples with those found in stack emissions from the incineration plant, significant differences are observed in the PCDD:PCDF ratio and in the contribution of the most chlorinated congeners. From this study we can conclude that the incineration plant is not the main source of PCDD/Fs in the studied area, which is apparently characterized by a homogeneous and widespread contamination situation, typical of an urban area.     

流化床垃圾焚烧炉产生的有毒二噁英同类物分布研究

测定了流化床垃圾焚烧炉焚烧产生的飞灰、烟尘和烟气中的2，3，7，8位氯取代二噁英同类物的含量及其毒性当量。结果表明，产生的二噁英主要存在于飞灰中，烟气中的含量很少。飞灰中二噁英总浓度和毒性当量分别为8.44ng／g和0．80ng／g，经过布袋除尘器后的烟尘和烟气中二噁英的浓度之和与毒性当量之和分别为0．34ng／m^3和0．02ng／m^3，而布袋除尘器前的烟尘和烟气中二噁英的浓度之和与毒性当量之和分别为40．78ng／m^3和3．0ng／m^3。飞灰和烟尘中2，3，7，8位氯取代二噁英同类物的分布相似，但是与烟气中2，3，7，8位氯取代二噁英同类物的分布差别较大。通过了解有毒二噁英同类物的分布，可以进一步优化流化床垃圾焚烧炉的焚烧条件，降低二噁英的排放量，减少垃圾焚烧对环境的污染。     

Generation of PCDD/F in fly ash from municipal solid waste incinerators

Fly ash from municipal solid waste incinerators (MSWIs) has been characterized in terms of polychlorinated dibenzyl-p-dioxin and polychlorinated dibenzofuran (PCDD/F) content. Increasing values of PCDD/Fs have been found to correlate with decreasing temperatures of sampling points in flue gas treatment lines of the plants, confirming other researchers' findings about temperature as the major controlling parameter for the PCDD/F formation. Measured PCDD/F ratios show that de novo synthesis is the dominant formation mechanism. The increasing trends of particulate-bound PCDD/Fs can be explained not only through the dominant de novo synthesis process but also considering the adsorption of gaseous PCDD/Fs on fly ash deposits, even outside the typical de novo synthesis temperature ranges. The effective role of a post-combustor unit, imposed by Italian law to destroy PCDD/ Fs, also needs to be carefully reconsidered.     

PCDD and PCDF exposures in workers and controls living near an industrial waste incinerator

This study measured the levels of 17 congeners of PCDDs/PCDFs in serum to compare the levels between potentially exposed workers at an industrial waste incinerator and any residents with no known exposures. The 1,2,3,6,7,8- and 1,2,3,7,8,9-HxCDD were detected in serum of workers but in controls. Likewise, 1,2,3,7,8-PeCDF, 1,2,3,6,7,8- and 1,2,3,7,8,9-HxCDF were detected only in serum of workers. The international toxic equivalent (TEQ) levels of PCDDs/PCDFs in sera of workers are much higher than in controls. Among PCDDs, the proportion of total concentration and TEQ level is dominated predominantly by 1,2,3,6,7,8- and 1,2,3,7,8,9-HxCDD. We need extensive studies to estimate human exposure and are continuing this investigation.     

Atmospheric deposition of PCDD/Fs near an old municipal solid waste incinerator: levels in soil and vegetation

The levels of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) were determined in soil and vegetation samples taken from 24 sites in the vicinity of an old municipal solid waste incinerator (San Adrià del Besòs, Barcelona, Spain). Duplicate samples were collected within a radius of 3 km from the stack. PCDD/F concentrations in soils ranged from 1.22 to 34.28 ng I-TEQ/kg (d.m.) with median and mean values of 9.06 and 12.24 ng I-TEQ/kg, respectively. In turn, the levels of PCDD/Fs in vegetation samples ranged from 0.33 to 1.98 ng I-TEQ/kg (d.m.), with median and mean values of 0.58 and 0.70 ng I-TEQ/kg, respectively. Although the present PCDD/F concentrations in soil samples were higher than those recently found in soils taken near other incinerators from Catalonia, they are of the same order of magnitude than the levels of these pollutants found in incinerators from other countries. By contrast, the concentrations of PCDD/Fs in herbage samples were comparable to those found in recent surveys carried out in Catalonia.     

电化学氧化法深度处理垃圾焚烧发电厂沥滤液生化出水

垃圾焚烧发电厂的沥滤液经生化处理后,COD和色度等仍然较高,达不到排放标准,必须进一步进行深度处理。采用自制的箱式四通道电化学反应器对垃圾焚烧发电厂沥滤液生化出水进行深度处理,研究了主要工艺参数——电流密度、表观流速、初始Cl^-浓度、比电极面积等因素对COD和色度去除效果的影响。适宜处理条件为：电流密度20 mA/cm²,反应器内表观流速2.92 cm/s,初始Cl^-浓度4 732 mg/L、比电极面积43.4 m²/m³。在此条件下处理废水10 min,色度就能达到排放要求,处理2 h,COD也能达到排放要求。考察反应器的能耗发现,电化学处理的能耗随电化学处理时间的延长呈不断增大的趋势。     

Thermal behavior of PCDD/PCDF in fly ash from municipal incinerators

The effect of thermal treatment of fly ash on the behaviour of PCDD/PCDF was studied in the range between 120 and 600° C. Annealing at 300° C (2 hrs) resulted in an increase of PCDD/PCDF concentration by a factor of 10 to 15. At 600° C degradation to concentrations below 0.1 ng/g is observed.     

流化床垃圾焚烧炉产生的有毒二(口恶)英同类物分布研究

测定了流化床垃圾焚烧炉焚烧产生的飞灰、烟尘和烟气中的2,3,7,8位氯取代二(口恶)英同类物的含量及其毒性当量.结果表明,产生的二(口恶)英主要存在于飞灰中,烟气中的含量很少.飞灰中二(口恶)英总浓度和毒性当量分别为8.44ng/g和0.80ng/g,经过布袋除尘器后的烟尘和烟气中二(口恶)英的浓度之和与毒性当量之和分别为0.34 ng/m3和0.02 ng/m3,而布袋除尘器前的烟尘和烟气中二(口恶)英的浓度之和与毒性当量之和分别为40.78 ng/m3和3.01ng/m3.飞灰和烟尘中2,3,7,8位氯取代二(口恶)英同类物的分布相似,但是与烟气中2,3,7,8位氯取代二(口恶)英同类物的分布差别较大.通过了解有毒二(口恶)英同类物的分布,可以进一步优化流化床垃圾焚烧炉的焚烧条件,降低二(口恶)英的排放量,减少垃圾焚烧对环境的污染.     

生活垃圾焚烧发电厂渗滤液蒸发浓缩处理

垃圾焚烧厂渗滤液因水质复杂,NH3-N、COD和电解质含量高等特点,成为一种难处理有机废水。采用负压蒸发浓缩法对渗滤液及电絮凝预处理渗滤液的处理进行了对比研究,并考查了浓缩比、pH等因素的影响。研究结果表明,电絮凝预处理不能改变渗滤液中COD、NH3-N的蒸发去除规律,即蒸发处理过程中,蒸发冷凝液中COD在蒸发前期和后期含量较高,蒸发中期较低;而NH3-N含量在蒸发处理前期较高,中后期含量较低。pH对蒸发处理影响较大,在酸性pH下COD去除率较低,但NH3-N去除率较高,可达95%以上,而在中碱性pH下,COD去除率增高,NH3-N去除率降低。渗滤液及电絮凝预处理渗滤液的一次蒸发冷凝液,经过二次蒸发处理后,冷凝液中COD和NH3-N含量均能达到一级排放标准,即分别低于100 mg/L和15 mg/L。     

Control of mercury emissions from a municipal solid waste incinerator in Japan

The control of Hg emissions from a municipal solid waste incinerator (MSWI) is very important, because more than 78% of municipal solid waste (MSW) is incinerated. The Hg content of coal used in utility boilers is relatively low in Japan. In this study, recent trends in the Hg content of MSW in Japan and activated carbon (AC) injection as a control technology of Hg emission from an MSWI are discussed. The effect of AC injection on Hg removal from flue gas in an MSWI was investigated by pilot-scale experiments using a bag filter (BF). The injection of AC increases the Hg reduction ratio by 20-30% compared with cases without AC injection. The Hg reduction ratio increases as the flue gas temperature decreases. The Hg reduction ratio is closely related to the inlet Hg concentration and was expressed with a Langmuir-type adsorption isotherm.     

Experimental and statistical determination of indicator parameters for the evaluation of fly ash and boiler ash PCDD/PCDF concentration from municipal solid waste incinerators

On-line detectable indicator parameters in the flue gas of municipal solid waste incinerators (MSWI) such as chlorinated benzenes (PCBz) are well known surrogate compounds for gas-phase PCDD/PCDF concentration. In the here presented work derivation of indicators is broadened to the detection of fly and boiler ash fractions with increased PCDD/PCDF content. Subsequently these fractions could be subject to further treatment such as recirculation in the combustion chamber to destroy their PCDD/PCDF and other organic pollutants' content. Aim of this work was to detect suitable on-line detectable indicator parameters in the gas phase, which are well correlated to PCDD/PCDF concentration in the solid residues. For this, solid residues and gas-phase samples were taken at three MSWI plants in Bavaria. Analysis of the ash content from different plants yielded a broad variation range of PCDD/PCDF concentrations especially after disturbed combustion conditions. Even during normal operation conditions significantly increased PCDD/PCDF concentrations may occur after unanticipated disturbances. Statistical evaluation of gas phase and ash measurements was carried out by means of principal component analysis, uni- and multivariate correlation analysis. Surprisingly, well known indicators for gas-phase PCDD/PCDF concentration such as polychlorinated benzenes and phenols proved to be insufficiently correlated to PCDD/PCDF content of the solid residues. Moreover, no single parameter alone was found appropriate to describe the PCDD/PCDF content of fly and boiler ashes. On the other hand, multivariate fitting of three or four parameters yielded convenient correlation coefficients of at least r=0.8 for every investigated case. Thereby, comprehension of plant operation parameters such as temperatures and air flow alongside concentrations of inorganic compounds in the gas phase (HCl, CO, SO2, NOx) gave the best results. However, the suitable set of parameters suited best for estimation of PCDD/PCDF concentration in solid residues has to be derived anew for each individual plant and type of ash.