Microwave pretreatment for enhancement of phosphorus release from dairy manure

Both the advanced oxidation process (AOP) using a combination of hydrogen peroxide addition and microwave heating (H2O2/microwave), and the microwave heating process were used for solubilization of phosphorus from liquid dairy manure. About 80% of total phosphate was released into the solution at a microwave heating time of 5 min at 170 degrees C. With an addition of H2O2, more than 81% of total phosphate could be released over a reaction period of 49 h at ambient temperature. The AOP process could achieve up to 85% of total phosphate release at 120 degrees C. The results indicated that both the microwave, and the AOP processes could effectively release phosphate from liquid dairy manure. These processes could serve as pretreatments for phosphorus recovery from animal wastes, and could be combined with the struvite crystallization process to provide a new approach in treating animal wastes.     

Wet peroxide degradation of atrazine

The high temperature (150-200 degrees C), high pressure (3.0-6.0 MPa) degradation of atrazine in aqueous solution has been studied. Under these extreme conditions atrazine steadily hydrolyses in the absence of oxidising agents. Additionally, oxygen partial pressure has been shown not to affect atrazine degradation rates. In no case mineralisation of the parent compound was observed. The addition of the free radical generator hydrogen peroxide to the reaction media significantly enhanced the depletion rate of atrazine. Moreover, partial mineralisation of the organics was observed when hydrogen peroxide was used. Again, oxygen presence did not influence the efficiency of the promoted reaction. Consecutive injections of hydrogen peroxide throughout the reaction period brought the total carbon content conversion to a maximum of 65-70% after 40 min of treatment (suggesting the total conversion of atrazine to cyanuric acid). Toxicity of the effluent measured in a luminometer decreased from 93% up to 23% of inhibition percentage. The process has been simulated by means of a semi-empirical model.     

Removal of nitrogenous compounds by catalytic wet air oxidation. Kinetic study

Aqueous wastes containing organic pollutants can be efficiently treated by wet air oxidation (WAO), i.e. oxidation by molecular oxygen in the liquid phase, under high temperature (200-325 degrees C) and pressure (up to 150 bar). However, organic nitrogen can be relatively resistant to oxidation and can be harmful to the environment. In the course of treatment, organic nitrogen (N-Org) is converted into ammonia (NH(3)), while organic carbon (C-Org) is converted mainly into carbon dioxide (CO(2)). This can be done without catalysts. In the presence of Mn/Ce composite oxides, it is possible to transform ammonia into molecular nitrogen at a temperature close to 260 degrees C. The direct conversion of organic nitrogen into molecular nitrogen also can be achieved using the same catalyst. This paper discusses the results obtained during the treatment of nitrogenous compounds like aniline, nitrophenol, beta-alanine and ammonia. Laboratory investigations were conducted in a stirred batch reactor with Mn/Ce composite oxides as catalysts. Very limited amounts of nitrites and nitrates were observed with amines, but more significant quantities were found with nitro-compounds. The kinetics of oxidation of ammonia, organic compounds, and more particularly aniline, were investigated. The treatment of a real waste (process wastewater) was also investigated. The dependence of the transformation rate on various parameters (amount of catalyst, temperature, etc.) was established. The rates of oxidation are described by first-order kinetic laws with respect to the various nitrogen species (aniline, NH(3)). Several parallel pathways are considered for the transformation of organic nitrogen, amongst which is an interaction with the catalyst surface. The orders with respect to oxygen and catalyst are established.     

Wet air oxidation of nitrobenzene enhanced by phenol

Simultaneous nitrobenzene and phenol wet air oxidation was investigated in a stainless autoclave at temperature range of 180-220 degrees C and 1.0 MPa oxygen partial pressure. Compared with the single oxidation of nitrobenzene under the same conditions, the presence of phenol in the reaction media greatly improved the removal efficiency of nitrobenzene. The effect of temperature on the reaction was studied. Phenol was considered as a type of initiator in the nitrobenzene oxidation.     

Microwave Pretreatment for Enhancement of Phosphorus Release from Dairy Manure

Both the advanced oxidation process (AOP) using a combination of hydrogen peroxide addition and microwave heating (H₂O₂/microwave), and the microwave heating process were used for solubilization of phosphorus from liquid dairy manure. About 80% of total phosphate was released into the solution at a microwave heating time of 5 min at 170°C. With an addition of H₂O₂, more than 81% of total phosphate could be released over a reaction period of 49 h at ambient temperature. The AOP process could achieve up to 85% of total phosphate release at 120°C. The results indicated that both the microwave, and the AOP processes could effectively release phosphate from liquid dairy manure. These processes could serve as pretreatments for phosphorus recovery from animal wastes, and could be combined with the struvite crystallization process to provide a new approach in treating animal wastes.     

Wet air oxidation of a reactive dye solution using CoAlPO(4)-5 and CeO(2) catalysts

Wet air oxidation of a prepared reactive dye solution was performed to assess the efficacy of CoAlPO(4)-5 and CeO(2) as catalysts in the reaction. Via adsorption and oxidation of dye, CoAlPO(4)-5 effectively decreased American Dye Manufacturers Institute and chemical oxygen demand (COD) values in the dye solution. At a reaction temperature of 135 degrees C and an applied pressure of 1.0 MPa, color and COD removal were as high as 95% and 90%, respectively, after 2 h. Active sites on the outer surface of CoAlPO(4)-5 are responsible for adsorption and decomposition of dye while active sites in the pores dominate further destruction and oxidation of intermediate products. Since the outer surface only represents a minor part of the total surface, the color removal does not increase appreciably with loading of CoAlPO(4)-5. The CeO(2) catalyst, calcined from cerium chloride under high thermal impact (type A CeO(2)) was very effective in removing color and COD from the solution. This catalyst demonstrated near 100% color removal at temperatures above 135 degrees C and the COD removal could be above 95% at 165 degrees C. With both CoAlPO(4)-5 and CeO(2) catalysts, COD rose and then fell back during the reaction, a feature typical of a consecutive reaction. In contrast to prepared CeO(2), a commercial CeO(2) did not exhibit any catalytic ability for the removal of color and COD. The durability of both CoAlPO(4)-5 and prepared CeO(2) is considered to be fair.     

Phosphorus recovery from fosfomycin pharmaceutical wastewater by wet air oxidation and phosphate crystallization

Fosfomycin pharmaceutical wastewater contains highly concentrated and refractory antibiotic organic phosphorus (OP) compounds. Wet air oxidation (WAO)-phosphate crystallization process was developed and applied to fosfomycin pharmaceutical wastewater pretreatment and phosphorus recovery. Firstly, WAO was used to transform concentrated and refractory OP substances into inorganic phosphate (IP). At 200 °C, 1.0 MPa and pH 11.2, 99% total OP (TOP) was transformed into IP and 58% COD was reduced. Subsequently, the WAO effluent was subjected to phosphate crystallization process for phosphorus recovery. At Ca/P molar ratio 2.0:1.0 or Mg/N/P molar ratio 1.1:1.0:1.0, 99.9% phosphate removal and recovery were obtained and the recovered products were proven to be hydroxyapatite and struvite, respectively. After WAO-phosphate crystallization, the BOD/COD ratio of the wastewater increased from 0 to more than 0.5, which was suitable for biological treatment. The WAO-phosphate crystallization process was proven to be an effective method for phosphorus recovery and for fosfomycin pharmaceutical wastewater pretreatment.     

湿式空气氧化法处理TNT红水的影响因素

使用湿式空气氧化技术与生物技术联合处理TNT精制阶段所产生的红水,研究了湿式空气氧化过程中反应温度、反应时间、初始压强和pH值对流出物的COD值与流出物可生化性的影响规律。研究结果表明,随着反应温度和反应初始压强的升高、反应时间的延长、催化剂投加量的增加和反应pH值的降低,出水COD值均有所下降。在温度为300℃、初始压强为14MPa、反应时间为2h、pH值为5,3、铁盐催化剂添加量为2g的条件下,出水COD值为498mg／L,COD去除率可达到99．27％。在温度为300℃、初始压强为11MPa、反应时间为1h、pH值为3、添加1g铁盐催化剂的条件下：反应流出物的BOD5／COD值为0．301,此时可生化性已经得到很好改善。通过生物方法对反应流出物后续处理发现,湿式空气氧化技术处理TNT红水在反应温度300℃以上,反应流出物均可生物降解。     

O3/H2O2法去除浮选药剂丁基黄药

采用O3/H2O2法去除水中丁基黄药,考察了H2O2/O3摩尔比、pH值、丁基黄药初始浓度、温度和自由基抑制剂对丁基黄药的去除效果的影响。结果表明,在相同O3投加量下,H2O2量越大,丁基黄药去除率越高。pH值为7～9,温度在293～303 K的范围内,O3/H2O2对丁基黄药都有很高的去除率。碳酸氢根和叔丁醇能在一定程度上降低丁基黄药的降解效率。研究还发现,在O3和H2O2投加量相同的条件下,H2O2多次投加对水中丁基黄药的处理效果明显优于一次性投加。GC/MS分析表明,O3/H2O2氧化丁基黄药氧化产物为羧酸类物质。     

O3/H2O2法去除浮选药剂丁基黄药

采用O3/H2O2法去除水中丁基黄药,考察了H2O2/O3摩尔比、pH值、丁基黄药初始浓度、温度和自由基抑制剂对丁基黄药的去除效果的影响。结果表明,在相同O3投加量下,H2O2量越大,丁基黄药去除率越高。pH值为7～9,温度在293～303 K的范围内,O3/H2O2对丁基黄药都有很高的去除率。碳酸氢根和叔丁醇能在一定程度上降低丁基黄药的降解效率。研究还发现,在O3和H2O2投加量相同的条件下,H2O2多次投加对水中丁基黄药的处理效果明显优于一次性投加。GC/MS分析表明,O3/H2O2氧化丁基黄药氧化产物为羧酸类物质。     

Kinetics and stoichiometry of aerobic sulfide oxidation in wastewater from sewers-effects of pH and temperature.

Kinetics and stoichiometry of aerobic chemical and biological sulfide oxidation in wastewater from sewer networks were studied. In this respect, the effects of temperature and pH were investigated in the ranges 10 to 20 degrees C and 5 to 9, respectively. The temperature dependency of sulfide oxidation kinetics was described using an Arrhenius relationship. The effect of pH on the rate of chemical sulfide oxidation is related to the dissociation of hydrogen sulfide (H2S) to hydrogen sulfide ion (HS(-)), with HS(-) being more readily oxidized than H2S. Biological sulfide oxidation exhibited the highest rates at ambient wastewater pH, and the reaction was inhibited at both low and high pH values. Chemical sulfide oxidation was found to produce thiosulfate and sulfate, while elemental sulfur was the main product of biological sulfide oxidation. Based on the investigations, general rate equations and stoichiometric constants were determined, enabling the processes to be incorporated to conceptual sewer process models.     

Fe/活性炭多相类Fenton法湿式氧化罗丹明B废水的研究

采用自制的Fe/活性炭（Fe/AC）为催化剂,H₂O₂为氧化剂,组成多相类Fenton试剂催化降解罗丹明B染料废水。实验结果表明,在催化剂加入量为0.8 g/L,H₂O₂体积分数为0.3%,废水pH值为13,反应时间为30 min的条件下,质量浓度为200 mg/L的罗丹明B染料废水的脱色率达100%。反应动力学研究表明,罗丹明B脱色反应近似为一级反应,30℃时反应速率常数为0.02675 min^-1,表观活化能为69.47 kJ/mol。     

Hydrogen peroxide photolysis, fenton reagent and photo-fenton for the degradation of nitrophenols: a comparative study

The kinetics of the degradation of seven nitrophenols (2-nitrophenol, 4-nitrophenol, 2,5-dinitrophenol, 2,6-dinitrophenol, 2,4-dinitrophenol, 2-methyl-4,6-dinitrophenol, 4-methyl-2,6-dinitrophenol) with the Fenton reagent, photo-Fenton, and hydrogen peroxide photolysis was investigated. The efficiency and operating costs for the studied treatments were evaluated and compared. The Fenton reagent was found to be the most efficient and the cheapest way for the nitrophenols (NPs) degradation. The formation of nitrate as a result of mineralisation of organically bounded nitrogen was observed during the treatment of NPs with studied treatment processes. The degrees of organically bounded nitrogen conversion to nitrate after 90% degradation of NPs with the Fenton, photo-Fenton and hydrogen peroxide photolysis were 51-67%, 85-90%, and 50-60%, respectively. According to Daphnia magna acute toxicity test, the Fenton treatment led to complete detoxification of NPs.     

Advanced oxidation processes for the treatment of olive-oil mills wastewater

In this work, the treatment of an actual industrial waste with three advanced oxidation processes (AOP) has been studied: conductive-diamond electrooxidation (CDEO), ozonation and Fenton oxidation. The wastewater comes from olive-oil mills (OMW) and contains a COD of nearly 3000 mg dm(-3). CDEO allowed achieving the complete mineralization of the waste with high current efficiencies. Likewise, both ozonation and Fenton oxidation were able to treat the wastes, but they obtained very different results in terms of efficiency and mineralization. The accumulation of oxidation-refractory compounds as final products excludes the use of ozonation and Fenton oxidation as a sole treatment technology. This confirms that besides the hydroxyl-radical mediated oxidation, CDEO combines other important oxidation processes such as the direct electro-oxidation on the diamond surface and the oxidation mediated by other electrochemically formed compounds generated on this electrode.     

Atrazine removal by ozonation processes in surface waters

Atrazine (6-chloro-N-ethyl-N'-isopropyl-1,3,5-triazinedyl-2,4-diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continuously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O3/H2O2 process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O3/H2O2 and O3/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Microwave enhanced advanced oxidation treatment of dairy manure

Abstract

The microwave enhanced advanced oxidation process (MW-AOP) was used to treat dairy manure in a continuous-flow 915?MHz microwave wastewater treatment system. The treatment efficiency increased with an increase in temperature, as well as hydrogen peroxide dosage. The settling property was also improved in all treated sets, regardless of temperature applied. The system operated at temperatures >100?°C had a much higher soluble chemical oxygen demand than at temperatures <100?°C. The highest soluble carbonaceous compounds, orthophosphate and ammonia were obtained at 110?°C and 0.6%H₂O₂ per % of total solids content. The process should be operated at higher temperatures and higher hydrogen peroxide dosages for maximizing solids disintegration, nutrient release and energy efficiency. An energy fingerprint correlating the cumulative energy consumption and temperature rise was developed. The results demonstrated that the custom designed MW-AOP system is suitable for the effective treatment of dairy manure. The system can readily be scaled up and integrated into a dairy farm manure treatment and resource recovery system.     

Experimental in situ chemical peroxidation of atrazine in contaminated soil

Lab-scale experiments of in situ chemical oxidation (ISCO), were performed on soil contaminated with 100 mg kg(-1) of atrazine (CIET). The oxidant used was hydrogen peroxide catalysed by naturally occurring minerals or by soluble Fe(II) sulphate, added in aqueous solution. The oxidation conditions were: CIET:H2O2=1:1100, 2 PV or 3 PV reaction volume, Fe(II):H2O2=0, 1:22, 1:11. Stabilized (with KH2PO4 at a concentration of 16 g l(-1)) or non-stabilized hydrogen peroxide was used. The pH of the reagents was adjusted to pH=1 with sulphuric acid, or was not altered. Results showed that the addition of soluble Fe(II) increased the temperature of the soil slurry and the use of stabilized hydrogen peroxide resulted in a lower heat generation. The treatment reduced the COD of the soil of about 40%, pH was lowered and natural organic matter became less hydrophobic. The highest atrazine conversion (89%) was obtained in the conditions: 3 PV, Fe(II):H2O2=1:11 with stabilized hydrogen peroxide added in two steps. The stabilizer only increased H2O2 life-time significantly when soluble Fe(II) was added. Results indicate as preferential degradation pathway of atrazine in soil dechlorination instead of dealkylation.     

Dibenzothiophene oxidation by horseradish peroxidase in organic media: effect of the DBT:H2O2 molar ratio and H2O2 addition mode

Its is well known that in the biodesulfurization (BDS) process the low water solubility of sulfur compounds hinders its transference from the oil phase to the cells being the rate-limiting step in the metabolism of dibenzothiophenes (DBT). Thus sulfur compounds derivatives with high water solubility could be more easily transported increasing the BDS efficiency. The present work performed a stepwise evaluation of the enzymatic oxidation of DBT by horseradish peroxidase (HRP). Reactions were carried out in monophasic organic media containing 25% (v/v) acetonitrile. The following parameters were evaluated: DBT:H2O2 molar ratio (1:1-1:20); H2O2 addition mode (single or stepwise); pH (6.0-8.0) and temperature (37-50 degrees C). Best results were observed in a reaction medium at pH 8.0 presenting HRP 0.06IUml(-1), DBT 0.267mM, DBT:H2O2 molar ratio of 1:20 (stepwise hydrogen peroxide addition) and incubated at 45 degrees C for 60min. Under these conditions 60% of DBT was converted into dibenzothiophene sulfoxide (12%) and dibenzothiophene sulfone (46%). The DBT oxidation rate observed in this work, of 5mmolmin(-1)g(-1) of HRP, was 250-fold higher than the BDS rate, 20mumolmin(-1)g(-1) of catalyst. As such a combined enzyme-microbial desulfurization process could be envisaged. Products were determined by HPLC RP C-18.     

Treatment of polychlorinated biphenyls in two surface soils using catalyzed H₂O₂ propagations

Two surface soils contaminated with polychlorinated biphenyls (PCBs) collected from Superfund sites in the New England region of the United States, Fletcher Paints and Merrimack Industrial Metals, were evaluated for field treatment at the bench level using catalyzed H₂O₂ propagations (CHP—modified Fenton’s reagent). The two soils were first evaluated for the potential for in situ treatment based on two criteria: (1) temperature (<40 °C after CHP reagent addition), and (2) hydrogen peroxide longevity (>24 h). In situ CHP remediation was more applicable to the Fletcher soil, while the Merrimack soil was better suited to ex situ treatment based on temperature increases and hydrogen peroxide lifetimes. Using the highest hydrogen peroxide concentrations appropriate for in situ treatment in each soil, PCB destruction was 94% in the Fletcher soil but only 48% in the Merrimack soil. However, 98% PCB destruction was achieved in the Merrimack soil using conditions more applicable to ex situ treatment (higher hydrogen peroxide concentrations with temperatures >40 °C). Analysis of degradation products by gas chromatography/mass spectroscopy showed no detectable chlorinated degradation products, suggesting that the products of PCB oxidation were rapidly dechlorinated and degraded. The results of this research document that the two PCB-contaminated soils studied can be effectively treated using aggressive CHP conditions, and that such a detailed bench study provides important information before implementing field treatment.     

Anaerobic digestion of thermo-oxidized excess municipal sludge.

The effect of a thermo-oxidative co-treatment placed between the two reactors of two-stage anaerobic digestion of excess municipal sludge was studied. The oxidant used was hydrogen peroxide (H2O2), and moderate temperatures below the boiling point of water were considered. The first experiment was to elucidate the effect of two different temperatures (65 and 90 degrees C) of oxidation using a constant oxidant dose of 1.0 g H2O2/g influent volatile suspended solids (VSSinfluent). The use of thermo-oxidative co-treatment increased overall solids destruction by 24.9 and 33.5%, respectively, when operating at 65 and 90 degrees C, respectively. Because of this significant effect of temperature on the performance of the process, a second experiment was conducted using the higher temperature of 90 degrees C while decreasing the hydrogen peroxide dosage to 0.5, 0.25, and 0.1 g H2O2/g VSSinfluent. An increase in solids destruction of 13.9, 18.9, and 25.6% was observed when the thermo-oxidative co-treatment was used using oxidant dosages of 0.1, 0.25, and 0.5 g H2O2/g VSSinfluent, respectively.