High compressive strength of home waste and polyvinyl acetate composites containing silica nanoparticle filler

Simple mixing and hot pressing methods were used to make composites from home waste—in particular, paper and dry leaves—using polyvinyl acetate (PVAc) as an adhesive and silica nanoparticles as filler. The optimum composition for the strongest composites, in terms of compressive strength, had a mass ratio of silica nanoparticles/PVAc/(paper + dry leaves) of 3:80:280. With this mass ratio, a compressive strength of 68.50 MPa was obtained for samples prepared at a pressing temperature of 150°C, pressing pressure of 100 MPa, and pressing time of 20 min. The addition of silica nanoparticles increased the compressive strength by about 50%, compared with composites made without the addition of nanosilica (45.60 MPa). Higher compressive strength was obtained at a higher pressing pressure. At a pressing pressure of 120 MPa, pressing temperature of 150°C, and pressing time of 20 min, a compressive strength of 69.10 MPa was obtained. When the pressing time was increased to 45 min at a pressing pressure of 120 MPa, a compressive strength of 84.37 MPa was measured. A model was also proposed to explain the effects of pressing pressure and pressing time on compressive strength. The model predictions were in good agreement with the experimental data.     

Accelerated carbonation treatment of industrial wastes

The disposal of industrial waste presents major logistical, financial and environmental issues. Technologies that can reduce the hazardous properties of wastes are urgently required. In the present work, a number of industrial wastes arising from the cement, metallurgical, paper, waste disposal and energy industries were treated with accelerated carbonation. In this process carbonation was effected by exposing the waste to pure carbon dioxide gas. The paper and cement wastes chemically combined with up to 25% by weight of gas. The reactivity of the wastes to carbon dioxide was controlled by their constituent minerals, and not by their elemental composition, as previously postulated. Similarly, microstructural alteration upon carbonation was primarily influenced by mineralogy. Many of the thermal wastes tested were classified as hazardous, based upon regulated metal content and pH. Treatment by accelerated carbonation reduced the leaching of certain metals, aiding the disposal of many as stable non-reactive wastes. Significant volumes of carbon dioxide were sequestrated into the accelerated carbonated treated wastes.     

Bioconversion of industrial wastes: paint sludge from automotive manufacturing

The compostability of water-based paint sludge originating from the automotive industry was investigated. Six reactors were operated. Wastewater treatment sludge from the same industry was used as additional substrate, and corncob was used as a bulking agent. The level of paint sludge within the compost mixtures varied between 55 and 85%. All reactors yielded a temperature increase up to thermophilic phase levels (>?40 °C) for a minimum of 5 days, and organic matter and C/N losses were observed. BTEX concentrations decreased during composting. Nickel and tin levels in the final product exceeded the legal compost limits. The calorific value of the compost mixtures increased from 9532 to 18774 kJ/kg at the end of the composting process. It was seen that the process applied in this study can be utilized as a biodrying step before the usage of paint sludge at cement kilns as additional fuel.     

Vacuum pyrolysis of polymeric wastes containing hazardous cyano groups

Vacuum pyrolysis of polymeric wastes containing hazardous cyano groups was studied using low temperature pyrolysis mass spectrometry. Specifically, the study analyzed the presence of toxic compounds among the pyrolysis products. The polymers were pyrolyzed directly in the solid probe of a quadruple mass spectrometer within an ion source at a pressure of 10^?6 Torr and then sorted by quadrupole mass analyzer. Polyethyl cyanoacrylate degrades by depolymerization, mostly into the ethyl cyanoacrylate monomer units. The degradation of polyurethane produces nonpolymeric urethane, isocyanates, amines and ethers. Polyacrylonitrile degrades via a depolymerization pathway into oligonitriles, acrylonitrile, ammonia and hydrogen cyanide.     

Polyalkylphenyl-sulphonic acids with acid groups of variable strength from animal-vegetable wastes

The insoluble organic fraction isolated from rice-hulls residues and animal fecal matter mixture is sulphonated in liquid SO3 at 200 degrees C to a water soluble sulphonate (III). III is compared to the sulphonate (IV) obtained from the same mix after composting. Both products have been found to contain mixtures of molecules with close molecular weight. These molecules consist of a central cicloaliphatic cluster with peripheral pending aromatic chains. III and IV appear to have the same sulphonation degree. However, the latter contains higher concentrations of cicloaliphatic fragments and of amide, phenol and ether bonds, but less carboxylic and amine functional groups. These differences may be reasonably traced back to the starting materials. By comparison with commercial lignosulphonates derived from the paper and pulp industry, the above arylsulphonates are likely candidates for a variety of applications in the chemical industry and in agriculture. We conclude that sulphonation, even under the drastic experimental conditions of this work, does not seem to erase the memory of the parent matter structure. This reaction is capable of upgrading recalcitrant organic matter in vegetable waste residues to an interesting variety of lignosulphonates.     

Development of composting process of oil palm industrial wastes by multi-enzymatic fungal system

There is an increased interest in composting as an effective means of handling large amounts of organic wastes generated by oil palm industries in Malaysia. However, very few studies have been conducted to develop an effective composting process using the multi-enzymatic system. This study demonstrates an effective composting process of EFB (empty fruit bunch) with POME (palm oil mill effluent), using the optimized process parameters and compatible multi-enzymatic fungal system. A higher decrease (3 %) of organic matter was achieved in the fungal treated system, almost double that of the control (without inoculum). The lowest C/N ratio and soluble protein content recorded were about 17 and 128.82 g/kg, respectively. The maximum germination index obtained was 116 % at day 50 of treatment, which is considered high compared to the control (uninoculated). Furthermore, the maximum activity of ligninase enzyme was found to be 25.95 U/g and the highest cellulase activity was recorded at 0.975 U/g.     

废渣基建材的危害性及控制措施

随着工业废渣的大力开发和利用,大量的工业废渣被用作建筑材料。为合理利用工业废渣,促进循环经济的发展,防止有害物质进入环境,提出了利用工业废渣生产建材的危害性控制措施。     

Effect of microsilica addition on compressive strength of rubberized concrete at elevated temperatures

An experimental investigation was carried out to study the effects of various percentages of fine/coarse tire waste and microsilica at various temperatures on the compressive strength of concrete. The compressive strength of concrete mixtures made with tire rubber was assessed statistically with those of concrete containing microsilica and conventional concretes in order to evaluate the usefulness of recycling rubber waste as a component of concrete. Results confirmed that the recipe and processing temperature of concrete cubes influence the compressive strength values. Generally, the use of microsilica or fine rubber mixed with microsilica as aggregate replacement of 5% by volume improved the compressive strength of concrete processed at a temperature of 150°C. The addition of coarse rubber did not achieve any increase in strength when used as an aggregate replacement at any percentage. Moreover, the reductions in the compressive strength of concrete mixes at higher temperatures were much smaller for the fine rubber with 5 vol% microsilica than those for control and coarse rubber mixes. The specimens made with fine rubber and 5 vol% microsilica at elevated temperatures above 400°C appeared to show very similar compressive strength values. The use of fine rubber in building construction could help save energy and reduce costs and solve the solid waste disposal problem posed by this type of waste.     

The influence of mix parameters and binder choice on the carbonation of cement solidified wastes

This paper explores the kinetics of carbonation of cement-based solidified hazardous waste. This study is part of a wide investigation into the effects of carbonation on solidified waste forms. Two commercially produced heavy metal wastes were solidified with three different types of Portland cement and two mineral admixtures and carbonated under controlled conditions. Measurements of the uptake of carbon dioxide were made for the different mixes and areas showing the degree of carbonation for each cement system were defined. The effects of water/binder ratio, waste and binder type on both total uptake of carbon dioxide and rate of carbonation were investigated and are discussed.     

Utilization of bottom ash from the incineration of separated wastes as a cement substitute.

Waste incineration is still an essential technology in the concept of integrated waste management. Most of the combustion residues are incinerator bottom ash. It has been discovered that incinerator bottom ash from the incineration of separated waste in the primary chamber of the modular two-stage incinerator mainly consists of metal oxides, especially SiO2 and CaO, in proportions that are quite similar to those in cement and so the feasibility of its application as a substitute for cement in concrete was investigated. It was found that after 28 days, the flexural and compressive strengths of the binder using bottom ash were practically comparable with those of a pure cement mixture. The results show that it is reasonable to use a binder containing incinerator bottom ash for applications in which an early-stage lower strength of concrete element is acceptable.     

Recovery of valuable metals from electronic and galvanic industrial wastes by leaching and electrowinning

In the present paper, a study on laboratory scale to perform a treatment for valuable metals recovery from electronic and galvanic industrial wastes, is reported. The characterisation of the waste, performed by XRD, SEM, EDX and chemical analysis, showed a high metals content in the sludge, such as Cu, Ni, Mn, Pb, Sn, W. A leaching process, coupled by electrowinning, is then proposed in order to reduce the volume of the waste material and to recover selectively valuable metals, such as Cu and Ni. During the leaching step, carried out by using H(2)SO(4), several factors were investigated (acid concentration, temperature and time of treatment). The leached liquor has been successfully treated with an electrowinning process, to recover copper and nickel. The copper and nickel depositions, were performed in acid and alkaline conditions, respectively. The Faraday yield was of about 95%. The energy consumption was 2.13 and 4.43 kWh per kg of copper and nickel recovered, respectively. At the end of the process, about 94-99% of the initial content of Cu and Ni was recovered at the cathode. The experimental results obtained, showed the technical feasibility of the process.     

Combined incineration of industrial wastes with in-plant residues in fluidized-bed utility boilers--decision relevant factors.

In Austria more than 50% of the high-calorific industrial residues and wastes generated are utilized for energy recovery in industrial utility boilers. This study investigated full-scale trials of combined incineration of in-plant residues with various industrial wastes. These trials were carried out in order to learn how the alternatively used fuel influences the incineration process itself as well as the quantity and quality of the various incineration products. The currently used fuel, which consisted of in-plant residues as well as externally acquired waste wood and the refuse-derived fuel (RDF) mixtures used during the full-scale trials are characterized in terms of material composition as well as chemical and physical parameters. An input-output mass balance for the incineration plant (two fluidized bed combustion units, 20 and 30 MW, respectively) has been established, based on the data collected during the full-scale incineration trials. Furthermore, pollutant concentrations in the off-gas as well as the solid incineration residue are reported. It is not only the pollutant content but also a variety of other internal as well as external factors that have to be considered if a company is to decide whether or not to thermally utilize specific waste types. Therefore a strengths and weaknesses profile for several types of waste and the specific industrial boiler is also presented.     

Comparison of alkaline industrial wastes for aqueous mineral carbon sequestration through a parallel reactivity study

Thirty-one alkaline industrial wastes from a wide range of industrial processes were acquired and screened for application in an aqueous carbon sequestration process. The wastes were evaluated for their potential to leach polyvalent cations and base species. Following mixing with a simple sodium bicarbonate solution, chemistries of the aqueous and solid phases were analyzed. Experimental results indicated that the most reactive materials were capable of sequestering between 77% and 93% of the available carbon under experimental conditions in four hours. These materials – cement kiln dust, spray dryer absorber ash, and circulating dry scrubber ash – are thus good candidates for detailed, process-oriented studies. Chemical equilibrium modeling indicated that amorphous calcium carbonate is likely responsible for the observed sequestration. High variability and low reactive fractions render many other materials less attractive for further pursuit without considering preprocessing or activation techniques.     

Hydration characteristics of coconut fibre-reinforced mortars containing CSA and Portland cement

Journal of Material Cycles and Waste Management - This study aims at investigation of the effects of incorporating natural fibres and two types of cement [ordinary Portland cement and calcium...     

Prediction of future disposal of end-of-life refrigerators containing CFC-11

The objective of this study was to predict the number of refrigerators containing CFC-11 blown isolation foam and the amount of CFC-11 banked in these refrigerators. By using a Weibull-based survival function, the number of CFC-11 containing and still-functioning refrigerators was estimated to be approximately 1.6 million in 2013 in Turkey. In order to determine the amount of CFC-11 in the isolation foam of these refrigerators, polyurethane (PU) foam samples were taken from a refrigerator manufactured in 1993 and the quantity of CFC-11 was analyzed by a GC-MS. It was determined that 113–195 mg CFC-11/g PU remains in the PU foam depending on the location such as door, sides, top and bottom. Knowing that a mid-sized refrigerator contains 4 kg PU on average, the total amount of PU foam to be disposed of is 6344 tons when the CFC-11 containing refrigerators in Turkey become obsolete in the near future. Furthermore, 717–1237 tons of CFC-11 are expected to be banked in the PU foam of these refrigerators which will exert an equivalent amount of ozone depleting potential (ODP). In addition, the global warming potential will vary between 3.4 and 5.9 million tons of CO₂.     

宁东能源化工基地工业固体废物综合利用现状分析、预测及建议

宁东能源化工基地目前以及将来都是宁夏回族自治区工业固体废物主要产生源,因此做好宁东能源基地工业固体废物污染防治工作就相当于解决了宁夏地区大部分工业固体废物问题。通过对基地在工业固体废物方面存在的问题进行剖析,提出宁东能源化工基地固体废物污染防治对策,旨在为减少宁东基地工业固体废物的产生量,提高工业固体废物的综合利用率。做好工业固体废物贮存、处置工作,提供科学指导,保证基地的高水平建设,为可持续发展提供科学依据。     

Immobilization of copper ions laden kaolin waste: influence of thermal treatment on its immobilization in cement paste

This work aims to study the influence of thermal treatment of Cu²⁺ laden kaolin wastes on its immobilization efficiency in cement paste. Compressive strength and toxicity characteristic leaching procedure (TCLP) of 5–20 % kaolin waste blended cement pastes were tested. X-ray diffraction (XRD) results illustrate that adsorption of Cu²⁺ ions modify the crystal structure of kaolinite mineral. Fourier transform infrared (FTIR) results indicate that the adsorption sites on the kaolin surface that were occupied with free water molecules have been replaced with Cu²⁺ ions adsorbed from aqueous solutions. The thermal treatment of kaolin waste improves fixation ratio of Cu²⁺ in cement pastes containing up to 20 % of thermally treated waste. This is due to: pozzolanic activity of calcined kaolin, conversion of leachable adsorbed Cu²⁺ ions into encapsulated unleachable phase that does not retard the hydration of cement as well as adsorption of much of leachable Cu²⁺ ions on surfaces of hydration products and occlusion in its lattice structure as illustrated from XRD, FTIR, thermogravimetric, scanning electron microscopy and TCLP results. The fixation ratio of Cu²⁺ in cement paste blended with 20 % of thermally treated kaolin waste, reaches maximum value of about 97 % compared to 82 % for cement paste blended with 20 % of untreated kaolin waste.     

Rapid screening procedure to optimise the anaerobic codigestion of industrial biowastes and agricultural livestock wastes in Cyprus

Small-scale experimental investigations were undertaken on the anaerobic digestion (AD) and codigestion of livestock waste and industrial biowastes. A simple procedure was developed to rapidly determine the suitability of wastes for digestion. The experiment was split into two phases; initially, the seed (digested brewery waste) was replaced by the test waste over a period of 5 days. During the second phase, the test waste was incubated and monitored for methanogenesis. Dairy cattle slurry was the most efficient co-substrate which, when codigested with pig slurry in an equal ratio achieved volatile solids destruction of 32%, CH(4) production rate of 97.4 ml d(-1), maximum CH(4) content of 61.6% and total gas yield of 2229 ml after 529 h. High fat content wastes were unsuitable for AD due to low pH value and because the dominant microbial reaction was fermentation. Codigestion was investigated to overcome any inhibitions; however, dairy cattle slurry, abattoir wastewater and NaOH additions did not lead to methanogenesis. Treating these wastes by AD is feasible but without CH(4) production.     

Properties of structural concrete with high-strength cement mixes containing waste paper sludge ash

Journal of Material Cycles and Waste Management - This paper studies the use of wastepaper sludge ash (WPSA) for structural concrete in binary and ternary mixes with high-strength cement and two...     

Environmental impact of incineration of calorific industrial waste: Rotary kiln vs. cement kiln

Rotary kiln incinerators and cement kilns are two energy intensive processes, requiring high temperatures that can be obtained by the combustion of fossil fuel. In both processes, fossil fuel is often substituted by high or medium calorific waste to avoid resource depletion and to save costs. Two types of industrial calorific waste streams are considered: automotive shredder residue (ASR) and meat and bone meal (MBM). These waste streams are of current high interest: ASR must be diverted from landfill, while MBM can no longer be used for cattle feeding. The environmental impact of the incineration of these waste streams is assessed and compared for both a rotary kiln and a cement kiln. For this purpose, data from an extensive emission inventory is applied for assessing the environmental impact using two different modeling approaches: one focusing on the impact of the relevant flows to and from the process and its subsystems, the other describing the change of environmental impact in response to these physical flows. Both ways of assessing emphasize different aspects of the considered processes. Attention is paid to assumptions in the methodology that can influence the outcome and conclusions of the assessment. It is concluded that for the incineration of calorific wastes, rotary kilns are generally preferred. Nevertheless, cement kilns show opportunities in improving their environmental impact when substituting their currently used fuels by more clean calorific waste streams, if this improvement is not at the expense of the actual environmental impact.