共基质下微生物燃料电池同步脱色甲基橙与产电性能

采用双室方形微生物燃料电池(MFC),以葡萄糖作为共基质,研究了共基质浓度对典型偶氮染料甲基橙在MFC阳极室中脱色效率及同步产电的影响。结果表明,在0~1.5 g/L浓度范围内,共基质浓度越大,甲基橙脱色率、COD去除率和最大输出电压越高。在共基质浓度为1.5 g/L,进水甲基橙为300 mg/L的条件下,8 h的脱色率高达95%,且在1 000 Ω外电阻下,最大输出电压达到662 mV;在无共基质条件下,8 h内对300 mg/L甲基橙的脱色率仅为7.5%,最大输出电压仅达到140 mV。厌氧对照实验表明,甲基橙在MFC中可以实现加速脱色,反应8 h后甲基橙在MFC中的脱色率提高了57%。该研究为开发新型MFC降解偶氮染料废水技术提供了理论依据。     

Influence of exogenous urea on photosynthetic pigments, 14CO2 uptake, and urease activity in Elodea densa—environmental implications

This paper analyzes the effect of exogenous urea in increased concentration gradient (0, 100, 500 and 1,000 mg L^?1) on photosynthetic pigments (measured spectrophotometrically), uptake of ¹⁴CO₂ (using radioisotope), and urease activity (by measuring ammonia with Nessler’s reagent) in leaves of Elodea densa Planch. We have observed that low concentration of urea (100 mg L^?1) stimulates the accumulation of photosynthetic pigments and intensifies photosynthesis in E. densa, whereas high concentration (1,000 mg L^?1) suppresses these processes. Urease activity increased by approximately 2.7 and 8 fold when exogenous urea concentrations were 100 and 500 mg L^?1, respectively. However, exogenous urea in high concentration (1,000 mg L^?1) decreased urease activity by 1.5 fold compared to the control. The necessity of mitigating urea and other nitrogen-containing compounds (NH₃ from urea) in water bodies has been discussed with emphasis on the potential for phytoremediation of urea using common water weed viz. E. densa.     

Evaluation of growth and biochemical indicators of Salvinia natans exposed to zinc oxide nanoparticles and zinc accumulation in plants

The adverse effects of zinc oxide nanoparticles (ZnO NPs) with an average diameter of 25 nm on the aquatic plant Salvinia natans (L.) All. were determined. Growth, superoxide dismutase (SOD) activity, catalase (CAT) activity, peroxidase activity, and chlorophyll content of the plants were measured after 7 days of exposure to different concentrations of ZnO NPs (1 to 50 mg L^?1). The particle distribution in the culture medium (without plants) during the first 24 h was determined using a Nanotrac 250 particle analyzer. We also investigated the zinc accumulation in leaves and roots of the plant after 7 days of exposure. Exposure to 50 mg L^?1 ZnO NPs significantly increased SOD and CAT activities (P?<?0.05) and significantly depressed photosynthetic pigments (P?<?0.05). However, plant growth was not significantly affected (P?>?0.05). NPs completely precipitated at the bottom of the container at 8 h except for the portions of dissolution and aggregation on the roots. ZnO NPs at a concentration of 50 mg L^?1 can adversely affect S. natans, and their stress is affected by their aggregation and dissolution.     

Evaluation of Acinetobacter sp. B9 for Cr (VI) resistance and detoxification with potential application in bioremediation of heavy-metals-rich industrial wastewater

Present work demonstrates Cr (VI) detoxification and resistance mechanism of a newly isolated strain (B9) of Acinetobacter sp. Bioremediation potential of the strain B9 is shown by simultaneous removal of major heavy metals including chromium from heavy-metals-rich metal finishing industrial wastewater. Strain B9 tolerate up to 350 mg L^?1 of Cr (VI) and also shows level of tolerance to Ni (II), Zn (II), Pb (II), and Cd (II). The strain was capable of reducing 67 % of initial 7.0 mg L^?1 of Cr (VI) within 24 h of incubation, while in presence of Cu ions 100 % removal of initial 7.0 and 10 mg L^?1 of Cr (VI) was observed with in 24 h. pH in the range of 6.0–8.0 and inoculum size of 2 % (v/v) were determined to be optimum for dichromate reduction. Fourier transform infrared spectroscopy and transmission electron microscopy studies suggested absorption or intracellular accumulation and that might be one of the major mechanisms behind the chromium resistance by strain B9. Scanning electron microscopy showed morphological changes in the strain due to chromium stress. Relevance of the strain for treatment of heavy-metals-rich industrial wastewater resulted in 93.7, 55.4, and 68.94 % removal of initial 30 mg L^?1 Cr (VI), 246 mg L^?1 total Cr, and 51 mg L^?1 Ni, respectively, after 144 h of treatment in a batch mode.     

Arsenic toxicity in garden cress (Lepidium sativum Linn.): significance of potassium nutrition

In a hydroponic culture, experiments were performed to study the influence of potassium (K) supplementation (0, 20, 40, 60, 80, and 100 mg L^?1) on the arsenic (As; 0, 8, and 10 mg L^?1)-accrued changes in growth traits (plant biomass, root–shoot length) and the contents of lepidine, As and K, in garden cress (Lepidium sativum Linn.) at 10 days after treatment. The changes in these traits were correlated with shoot proline content, protein profile, and the activities of antioxidant enzymes namely superoxide dismutase (SOD, EC 1.15.1.1), catalase (CAT, EC 1.11.1.6), glutathione reductase (GR, EC 1.8.1.7), and ascorbate peroxidase (APX, EC 1.11.1.11). In general, As-alone treatments significantly decreased the growth traits but lead to significant enhancements in shoot proline and enzyme activities. K-supplementation to As-treated L. sativum seedlings decreased shoot-As content, reduced As-induced decreases in growth traits but enhanced the content of shoot proline, and the activities of the studied enzymes maximally with K₁₀₀ + As₈ and As₁₀ mg L^?1. Both 8 and 10 mg L^?1 of As drastically downregulated the shoot proteins ranging from 43–65 kDa. With As₁₀ mg L^?1, there was a total depletion of protein bands below 23 kDa; however, K₈₀ mg L^?1 maximally recovered and upregulated the protein bands. Additionally, protein bands were downregulated (at par with As-alone treatment) above K₈₀ mg L^?1 level. Interestingly, As-stress increased lepidine content in a dose-dependent manner which was further augmented with the K-supplementation. It is suggested that K protects L. sativum against As-toxicity by decreasing its accumulation and strengthening antioxidant defense system and protein stability.     

Influence of operational key parameters on the photocatalytic decolorization of Rhodamine B dye using Fe2+/H2O2/Nb2O5/UV system

The present research deals with the development of a new heterogeneous photocatalysis and Fenton hybrid system for the removal of color from textile dyeing wastewater as Rhodamine B (RhB) solutions by using Fe²⁺/H₂O₂/Nb₂O₅ as a photocatalytic system. The application of this photocatalytic system for the decolorization of dye contaminants is not reported in the literature yet. Different parameters like dye concentration, Nb₂O₅/Fe²⁺ catalyst amount, pH, and H₂O₂ concentration have been studied. The optimum conditions for the decolorization of the dye were initial concentration of 10 mg L^?1 of dye, pH 4, and Nb₂O₅/Fe²⁺ catalyst concentration of 0.5 g L^?1/50 mg L^?1. The optimum value of H₂O₂ concentration for the conditions used in this study was 700 mg L^?1. Moreover, the efficiency of the Nb₂O₅/photo-Fenton hybrid process in comparison to photo-Fenton alone and a dark Fenton process as a control experiment to decolorize the RhB solution has been investigated. The combination of photo-Fenton and Nb₂O₅ catalysts has been proved to be the most effective for the treatment of such type of wastewaters. The results revealed that the RhB dye was decolorized in a higher percent (78 %) by the Nb₂O₅/photo-Fenton hybrid process (Fe²⁺/H₂O₂/Nb₂O₅/UV) than by the photo-Fenton process alone (37 %) and dark Fenton process (14 %) after 120 min of treatment. Moreover, the Nb₂O₅ catalyst as a heterogeneous part of the photocatalytic system was demonstrated to have good stability and reusability.     

Toxicity of atrazine and its bioaccumulation and biodegradation in a green microalga,Chlamydomonas mexicana

This study evaluated the toxicity of herbicide atrazine, along with its bioaccumulation and biodegradation in the green microalga Chlamydomonas mexicana. At low concentration (10 μg L^?1), atrazine had no profound effect on the microalga, while higher concentrations (25, 50, and 100 μg L^?1) imposed toxicity, leading to inhibition of cell growth and chlorophyll a accumulation by 22 %, 33 %, and 36 %, and 13 %, 24 %, and 27 %, respectively. Atrazine 96-h EC50 for C. mexicana was estimated to be 33 μg L^?1. Microalga showed a capability to accumulate atrazine in the cell and to biodegrade the cell-accumulated atrazine resulting in 14–36 % atrazine degradation at 10–100 μg L^?1. Increasing atrazine concentration decreased the total fatty acids (from 102 to 75 mg g^?1) and increased the unsaturated fatty acid content in the microalga. Carbohydrate content increased gradually with the increase in atrazine concentration up to 15 %. This study shows that C. mexicana has the capability to degrade atrazine and can be employed for the remediation of atrazine-contaminated streams.     

Bioelectrochemical anaerobic sewage treatment technology for Arctic communities

This study describes a novel wastewater treatment technology suitable for small remote northern communities. The technology is based on an enhanced biodegradation of organic carbon through a combination of anaerobic methanogenic and microbial electrochemical (bioelectrochemical) degradation processes leading to biomethane production. The microbial electrochemical degradation is achieved in a membraneless flow-through bioanode–biocathode setup operating at an applied voltage below the water electrolysis threshold. Laboratory wastewater treatment tests conducted through a broad range of mesophilic and psychrophilic temperatures (5–23 °C) using synthetic wastewater showed a biochemical oxygen demand (BOD₅) removal efficiency of 90–97% and an effluent BOD₅ concentration as low as 7 mg L^?1. An electricity consumption of 0.6 kWh kg^?1 of chemical oxygen demand (COD) removed was observed. Low energy consumption coupled with enhanced methane production led to a net positive energy balance in the bioelectrochemical treatment system.     

Utilization of water chestnut for reclamation of water environment and control of cyanobacterial blooms

Overgrowth of water chestnut (Trapa spp.) is a regional problem throughout Asia and North America because of waterway blockage and water fouling upon decomposition. In the present study, we investigated the potential of water chestnut to control cyanobacterial blooms, via a high content of phenolic compounds. In addition, we assessed the impact of biomass harvesting and crude extract application on nutrient balance. We showed that the floating parts of water chestnut contained high concentrations of total phenolics (89.2 mg g^?1 dry weight) and exhibited strong antioxidant activity (1.31 mmol g^?1 dry weight). Methanol-extracted phenolics inhibited growth of Microcystis aeruginosa; the half maximal effective concentration (EC₅₀) of the extracted phenolics was 5.8 mg L^?1, which was obtained from only 103 mg L^?1 of dry biomass (the floating and submerged parts). However, the crude extracts also added important quantities of nitrogen, phosphorus, and potassium (1.49, 1.05, and 16.3 mg g^?1, respectively; extracted dry biomass weight basis); therefore, in practice, nutrient removal before and/or after the extraction is essential. On the other hand, biomass harvesting enables recovery of nitrogen, phosphorus, and potassium from the water environment (23.1, 2.9, and 18.7 mg g^?1, respectively; dry biomass weight basis). Our findings indicate that water chestnut contains high concentrations of phenolics and exhibits strong antioxidant activity. Utilization of these resources, including nutrients, will contribute to reclamation of the water environment, and also to disposal of wet biomass.     

Stormwater harvesting from landscaped areas: effect of herbicide application on water quality and usage

The suitability of stormwater harvested from pervious pavement system (PPS) structures for reuse purposes was investigated in conditions where glyphosate-containing herbicides (GCH) are applied as part of PPS maintenance procedure. The experiment was based on the four-layered design previously described as detailed in CIRIA C582. Results indicated that the highest sodium absorption ratio (SAR) of 1.6 recorded in this study, was less than that at which loss of permeability begins to occur as well as deterioration of matrix structure. Furthermore, the maximum electrical conductivity (ECw) of 2990 μS cm^?1, recorded for 7200 mg L^?1 concentration (GCH) was slightly below the unstable classification range at which salinity problems related to water quality occur such that salts accumulate in the root zone to the extent that crop yields are adversely affected. However, GCH concentration of 720 mg L^?1 was within ‘permissible’ range while that of 72 mg L^?1 was within ‘excellent’ range. Current study raises some environmental concerns owing to the overall impact that GCH at concentrations above 72 mg L^?1 exerts on the net performance of the organic decomposers, heavy metal and hydrocarbon release from the system and thus, should be further investigated. However, effluent from all the test models including those dosed with high GCH concentration of 7200 mg L^?1 do not pose any threat in terms of infiltration or deterioration associated with salinity although, there are indications that high dosage of the herbicide could lead to an elevated electrical conductivity of the recycled water.

Open image in new window

Graphical abstract Impact of herbicide on irrigation water quality

     

Investigation of chloramine-T impact on crayfish Astacus leptodactylus (Esch., 1823) cardiac activity

The crayfish play an essential role in the biomonitoring and may reflect ambient water quality through the biochemical, behavioural and physiological reactions. To assess whether narrow-clawed crayfish Astacus leptodactylus can respond by heart rate changes to presence in water of such biocide as chloramine-T, adult males were exposed to its low (2 and 5 mg L^?1), moderate (10 mg L^?1, commonly used in industry and aquaculture) and exceeded (20 and 50 mg L^?1) concentrations. In addition, a physical stress test evaluated energy expenditure following the chemical trials. Three key reactions (cardiac initial, first-hour and daily prolonged exposure) were discussed with particular focus on crayfish initial reaction as the most meaningful in on-line water quality biomonitoring. After short-term exposure to both chloramine-T concentrations, crayfish were found to respond rapidly, within 2–5 min. According to heart rate changes, the 1-h exposure did not adversely affect crayfish at either concentration, as well as during daily exposure to 10 mg L^?1. As assessed by the heart rate, the 24-h exposure to 50 mg L^?1 of chloramine-T was toxic for crayfish and led to substantial loss of energy that became apparent during subsequently conducted physical stress. The results supported a hypothesis that crayfish vital functions are connected with environment they inhabit closely enough to serve as biological monitors. Crayfish were tolerant to short-term chloramine-T exposure, while rapid crayfish reaction to an increased chemical level indicated their high sensitivity, an essential attribute of real-time environmental assessment.     

Phytoaccumulation potentials of two biotechnologically propagated ecotypes of Arundo donax in copper-contaminated synthetic wastewater

An in vitro experiment was carried out to evaluate the phytoremediation potentials of two somatic embryo-derived ecotypes of Arundo donax—BL (American ecotype) and 20SZ (Hungarian ecotype)—of copper from synthetic wastewater. The two ecotypes were grown under sterile conditions in tubes containing a nutrient solution supplied with increasing doses of Cu (0, 1, 2, 3, 5, 10, and 26.8 mg L^?1) for 6 weeks. The translocation and bioaccumulation factors and removal rate were estimated. In general, increasing Cu concentration in nutrient solution slightly decreased root, stem and leaf biomass without toxicity symptoms up to 26.8 mg L^?1. Moreover, both ecotypes showed high Cu removal efficiency from aqueous solution. However, Cu removal rate ranged between 96.6 to 98.8 % for BL ecotype and 97 to 100 % for 20SZ ecotype. Data illustrated that both BL and 20SZ ecotypes may be employed to treat Cu-contaminated water bodies up to 26.8 mg L^?1.     

Bioremediation of Cd and carbendazim co-contaminated soil by Cd-hyperaccumulator Sedum alfredii associated with carbendazim-degrading bacterial strains

The objective of this study was to develop a bioremediation strategy for cadmium (Cd) and carbendazim co-contaminated soil using a hyperaccumulator plant (Sedum alfredii) combined with carbendazim-degrading bacterial strains (Bacillus subtilis, Paracoccus sp., Flavobacterium and Pseudomonas sp.). A pot experiment was conducted under greenhouse conditions for 180 days with S. alfredii and/or carbendazim-degrading strains grown in soil artificially polluted with two levels of contaminants (low level, 1 mg kg^?1 Cd and 21 mg kg^?1 carbendazim; high level, 6 mg kg^?1 Cd and 117 mg kg^?1 carbendazim). Cd removal efficiencies were 32.3–35.1 % and 7.8–8.2 % for the low and high contaminant level, respectively. Inoculation with carbendazim-degrading bacterial strains significantly (P?<?0.05) increased Cd removal efficiencies at the low level. The carbendazim removal efficiencies increased by 32.1–42.5 % by the association of S. alfredii with carbendazim-degrading bacterial strains, as compared to control, regardless of contaminant level. Cultivation with S. alfredii and inoculation of carbendazim-degrading bacterial strains increased soil microbial biomass, dehydrogenase activities and microbial diversities by 46.2–121.3 %, 64.2–143.4 %, and 2.4–24.7 %, respectively. Polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) analysis revealed that S. alfredii stimulated the activities of Flavobacteria and Bradyrhizobiaceae. The association of S. alfredii with carbendazim-degrading bacterial strains enhanced the degradation of carbendazim by changing microbial activity and community structure in the soil. The results demonstrated that association of S. alfredii with carbendazim-degrading bacterial strains is promising for remediation of Cd and carbendazim co-contaminated soil.     

Removal of organochlorine pesticides from lindane production wastes by electrochemical oxidation

This study is focused on the effective removal of recalcitrant pollutants hexaclorocyclohexanes (HCHs, isomers α, β, γ, and δ) and chlorobenzenes (CBs) present in a real groundwater coming from a landfill of an old lindane factory. Groundwater is characterized by a total organic carbon (TOC) content of 9 mg L^?1, pH₀?=?7, conductivity?=?3.7 mS cm^?1, high salt concentration (SO₄^2?, HCO₃^?, Cl^?), and ferrous iron in solution. The experiments were performed using a BDD anode and a carbon felt (CF) cathode at the natural groundwater pH and without addition of supporting electrolyte. The complete depletion of the four HCH isomers and a mineralization degree of 90% were reached at 4-h electrolysis with a current intensity of 400 mA, the residual TOC (0.8 mg L^?1) corresponding mainly to formic acid. A parallel series reaction pathway was proposed: HCHs and CBs are transformed into chlorinated and hydroxylated intermediates that are rapidly oxidized to non-toxic carboxylic acids and/or mineralized, leading to a rapid decrease in solution pH.     

Assessment of solar driven TiO2-assisted photocatalysis efficiency on amoxicillin degradation

The objective of this work was to evaluate the efficiency of a solar TiO₂-assisted photocatalytic process on amoxicillin (AMX) degradation, an antibiotic widely used in human and veterinary medicine. Firstly, solar photolysis of AMX was compared with solar photocatalysis in a compound parabolic collectors pilot scale photoreactor to assess the amount of accumulated UV energy in the system (Q _UV) necessary to remove 20 mg L^?1 AMX from aqueous solution and mineralize the intermediary by-products. Another experiment was also carried out to accurately follow the antibacterial activity against Escherichia coli DSM 1103 and Staphylococcus aureus DSM 1104 and mineralization of AMX by tracing the contents of dissolved organic carbon (DOC), low molecular weight carboxylate anions, and inorganic anions. Finally, the influence of individual inorganic ions on AMX photocatalytic degradation efficiency and the involvement of some reactive oxygen species were also assessed. Photolysis was shown to be completely ineffective, while only 3.1 kJ_UV?L^?1 was sufficient to fully degrade 20 mg L^?1 AMX and remove 61 % of initial DOC content in the presence of the photocatalyst and sunlight. In the experiment with an initial AMX concentration of 40 mg L^?1, antibacterial activity of the solution was considerably reduced after elimination of AMX to levels below the respective detection limit. After 11.7 kJ_UV?L^?1, DOC decreased by 71 %; 30 % of the AMX nitrogen was converted into ammonium and all sulfur compounds were converted into sulfate. A large percentage of the remaining DOC was in the form of low molecular weight carboxylic acids. Presence of phosphate ions promoted the removal of AMX from solution, while no sizeable effects on the kinetics were found for other inorganic ions. Although the AMX degradation was mainly attributed to hydroxyl radicals, singlet oxygen also plays an important role in AMX self-photosensitization under UV/visible solar light.     

Solar CPC pilot plant photocatalytic degradation of bisphenol A in waters and wastewaters using suspended and supported-TiO2. Influence of photogenerated species

Photocatalytic degradation of bisphenol A (BPA) in waters and wastewaters in the presence of titanium dioxide (TiO₂) was performed under different conditions. Suspensions of the TiO₂ were used to compare the degradation efficiency of BPA (20 mg L^?1) in batch and compound parabolic collector (CPC) reactors. A TiO₂ catalyst supported on glass spheres was prepared (sol–gel method) and used in a CPC solar pilot plant for the photodegradation of BPA (100 μg L^?1). The influence of OH·, O₂ ^·?, and h ⁺ on the BPA degradation were evaluated. The radicals OH· and O₂ ^·? were proved to be the main species involved on BPA photodegradation. Total organic carbon (TOC) and carboxylic acids were determined to evaluate the BPA mineralization during the photodegradation process. Some toxicological effects of BPA and its photoproducts on Eisenia andrei earthworms were evaluated. The results show that the optimal concentration of suspended TiO₂ to degrade BPA in batch or CPC reactors was 0.1 g L^?1. According to biological tests, the BPA LC₅₀ in 24 h for E. andrei was of 1.7?×?10^?2 mg cm^?2. The photocatalytic degradation of BPA mediated by TiO₂ supported on glass spheres suffered strong influence of the water matrix. On real municipal wastewater treatment plant (MWWTP) secondary effluent, 30 % of BPA remains in solution; nevertheless, the method has the enormous advantage since it eliminates the need of catalyst removal step, reducing the cost of treatment.     

Responses of earthworm to aluminum toxicity in latosol

Excess aluminum (Al) in soils due to acid rain leaching is toxic to water resources and harmful to soil organisms and plants. This study investigated adverse impacts of Al levels upon earthworms (Eisenia fetida) from the latosol (acidic red soil). Laboratory experiments were performed to examine the survival and avoidance of earthworms from high Al concentrations and investigate the response of earthworms upon Al toxicity at seven different Al concentrations that ranged from 0 to 300 mg kg^?1 over a 28-day period. Our study showed that the rate of the earthworm survival was 100 % within the first 7 days and decreased as time elapsed, especially for the Al concentrations at 200 and 300 mg kg^?1. A very good linear correlation existed between the earthworm avoidance and the soil Al concentration. There was no Al toxicity to earthworms with the Al concentration ≤50 mg kg^?1, and the toxicity started with the Al concentration ≥100 mg kg^?1. Low Al concentration (i.e., <50 mg kg^?1) enhanced the growth of the earthworms, while high Al concentration (>100 mg kg^?1) retarded the growth of the earthworms. The weight of earthworms and the uptake of Al by earthworms increased with the Al concentrations from 0 to 50 mg kg^?1 and decreased with the Al concentrations from 50 to 300 mg kg^?1. The protein content in the earthworms decreased with the Al concentrations from 0 to 100 mg kg^?1 and increased from 100 to 300 mg kg^?1. In contrast, the catalase (CAT) and superoxide dismutase (SOD) activities in the earthworms increased with the Al concentrations from 0 to 100 mg kg^?1 and decreased from 100 to 300 mg kg^?1. The highest CAT and SOD activities and lowest protein content were found at the Al concentration of 100 mg kg^?1. Results suggest that a high level of Al content in latosol was harmful to earthworms.     

Effect of exogenous abscisic acid on the level of antioxidants in Atractylodes macrocephala Koidz under lead stress

This study hypothesized that the positive or negative effects of exogenous abscisic acid (ABA) on oxidative stress caused by lead were dose dependent. The effects of different levels of ABA (2.5, 5, and 10 mg L^?1) on lead toxicity in the leaves of Atractylodes macrocephala were studied by investigating plant growth, soluble sugars, proteins, lipid peroxidation, and antioxidative enzymes. Excess Pb inhibited root dry weight, root length, and the number of lateral roots, but increased shoot growth. In addition, lead stress significantly decreased the levels of chlorophyll pigments, protein, and activities of superoxide dismutase (SOD), catalase (CAT), ascorbate peroxidase (APX), and peroxidase (POD). Different levels of ABA significantly increased SOD, CAT, POD, and APX activities, but decreased the level of hydrogen peroxide and malondialdehyde in nonstressed plants. Exogenous application of 2.5 mg L^?1 ABA detoxified the stress-generated damages caused by Pb and also enhanced plant growth, soluble sugars, proteins, and all four antioxidant enzyme activities but reduced Pb uptake of lead-stressed plant compared to lead treatment alone. However, the toxic effects of Pb were further increased by the applications of 5 and 10 mg L^?1 ABA. The levels of antioxidants caused by a low concentration of exogenous ABA might be responsible for minimizing the Pb-induced toxicity in A. macrocephala.     

Dechlorination of chloroorganics,decolorization, and simultaneous bioremediation of Cr6+ from real tannery effluent employing indigenous Bacillus cereus isolate

A native Bacillus cereus isolate has been employed, for the first time, for simultaneous decolorization, dechlorination of chloroorganics, and Cr⁶⁺ remediation from the real tannery effluent. Most of the physicochemical variables in 3:1 diluted effluent were well above the standard prescribed limits, which decreased substantially upon microbial treatment. The extent of bioremediation was better in diluted (3:1) as compared to undiluted effluent supplemented with nutrients and augmented with B. cereus isolate. Maximum growth, effluent decolorization (42.5 %), dechlorination (74.1 %), and Cr⁶⁺ remediation (34.2 %) were attained with 4.0 % (v/v) inoculum, 0.8 % glucose, and 0.2 % ammonium chloride in 3:1 diluted effluent at natural pH (8.1) within 72 h of incubation. The efficiency of bioremediation in a bioreactor was higher as compared to a flask trial during 72 h of incubation: decolorization (47.9 %) was enhanced by 5.4 %, dechlorination (77.4 %) by 3.3 %, and Cr⁶⁺ removal (41.7 %) by 7.5 % at an initial color of 286 Pt-Co units and initial concentration of 62 mg chloride ions and 108 mg l^?1 Cr⁶⁺. Immobilized biomass of Pseudomonas putida and B. cereus coculture enhanced the extent of Cr⁶⁺ remediation (51.9 %) by 10.2 % compared to the bioreactor trial. Chromate reductase activity and reduced Cr directly correlated and were mainly associated with soluble fraction of B. cereus plus effluent natural microflora. The GC-MS analyses revealed the formation of metabolites such as acetic acid and 2-butenoic acid in bacterially treated effluent. The supplementation of nutrients along with B. cereus augmentation is required for efficient effluent bioremediation.     

Copper bioaccumulation,photosystem II functioning,and oxidative stress in the seagrass <Emphasis Type="Italic">Cymodocea nodosa</Emphasis> exposed to copper oxide nanoparticles

Photosynthetic activity, oxidative stress, and Cu bioaccumulation in the seagrass Cymodocea nodosa were assessed 4, 12, 24, 48, and 72 h after exposure to two copper oxide nanoparticle (CuO NP) concentrations (5 and 10 mg L^?1). CuO NPs were characterized by scanning electron microscopy (SEM) and dynamic light scattering measurements (DLS). Chlorophyll fluorescence analysis was applied to detect photosystem II (PSII) functionality, while the Cu accumulation kinetics into the leaf blades was fitted to the Michaelis-Menten equation. The uptake kinetics was rapid during the first 4 h of exposure and reached an equilibrium state after 10 h exposure to 10 mg L^?1 and after 27 h to 5 mg L^?1 CuO NPs. As a result, 4-h treatment with 5 mg L^?1 CuO NPs, decreased the quantum yield of PS II photochemistry (Φ _PSΙΙ ) with a parallel increase in the regulated non-photochemical energy loss in PSII (Φ _NPQ ). However, the photoprotective dissipation of excess absorbed light energy as heat, through the process of non-photochemical quenching (NPQ), did not maintain the same fraction of open reaction centers (q _p ) as in control plants. This reduced number of open reaction centers resulted in a significant increase of H₂O₂ production in the leaf veins serving possibly as an antioxidant defense signal. Twenty-four-hour treatment had no significant effect on Φ _PSΙΙ and q _p compared to controls. However, 24 h exposure to 5 mg L^?1 CuO NPs increased the quantum yield of non-regulated energy loss in PSII (Φ _NO ), and thus the formation of singlet oxygen (¹O₂) via the triplet state of chlorophyll, possible because the uptake kinetics had not yet reached the equilibrium state as did 10 mg L^?1. Longer-duration treatment (48 and 72 h) had less effect on the allocation of absorbed light energy at PSII and the fraction of open reaction centers, compared to 4-h treatment, suggesting the function of a stress defense mechanism. The response of C. nodosa leaves to CuO NPs fits the “Threshold for Tolerance Model” with a threshold time (more than 4 h) required for induction of a stress defense mechanism, through H₂O₂ production.