Adsorption and removal of As(V) and As(III) using Zr-loaded lysine diacetic acid chelating resin

An adsorption process for the removal of As(V) and As(III) was evaluated under various conditions using zirconium(IV) loaded chelating resin (Zr-LDA) with lysine-Nalpha,Nalpha diacetic acid functional groups. Arsenate ions strongly adsorbed in the pH range from 2 to 5, while arsenite was adsorbed between pH 7 and 10.5. The sorption mechanism is an additional complexation between arsenate or arsenite and Zr complex of LDA. Adsorption isotherm data could be well interpreted by Langmuir equation for As(V) at pH 4 and As(III) at pH 9 with a binding constant 227.93 and 270.47 dm3 mol(-1) and capacity constant 0.656 and 1.1843 mmol g(-1), respectively. Regeneration of the resin was carried out for As(V) using 1 M NaOH. Six adsorption/desorption cycles were performed without significant decrease in the uptake performance. Column adsorption studies showed that the adsorption of As(V) is more favorable compared to As(III), due to the faster kinetics of As(V) compared to As(III). Influence of the coexisting ions on the adsorption of As(V) and As(III) was studied. The applicability of the method for practical water samples was studied.     

Adsorption of As(III) on chitosan-Fe-crosslinked complex (Ch-Fe)

It was reported the adsorption of As(III) on the surface of the chitosan-Fe-crosslinked complex. Theoretical correlation of the experimental equilibrium adsorption data for As(III)/Ch-Fe system is best explained by the non-linearized form Langmuir-Freundlich isotherm model. At optimum conditions, pH 9.0, the maximum adsorption capacity, calculated using the Langmuir-Freundlich isotherm model was 13.4 mg g⁻¹. The adsorption kinetics of As(III) onto Ch-Fe are described by the pseudo-first-order kinetic equation. The results of the Mössbauer spectroscopy showed that there is no redox process on the surface of the adsorbent.     

Organo-modified sericite in the remediation of an aquatic environment contaminated with As(III) or As(V)

The aim of this investigation was to obtain the hybrid material precursor to the naturally and abundantly available sericite, a mica-based clay; the materials were further employed in the remediation of arsenic from aqueous solutions. The study was intended to provide a cost-effective and environmentally benign treatment technology. The hybrid organo-modified sericite was obtained using hexadecyltrimethylammonium bromide (HDTMA) and alkyldimethylbenzylammonium chloride (AMBA) organic surfactants by introducing regulated doses of HDTMA or AMBA. The materials were characterized using infrared and X-ray diffraction analytical data, whereas the surface morphology was discussed by taking its SEM images. These materials were employed to assess the pre-concentration and speciation of As(III) and As(V) from aqueous solutions. The batch reactor data showed that increasing the sorptive concentration (from 1.0 to 15.0 mg/L) and pH (i.e., pH 2.0 to 10.0) caused the percent uptake of As(III) and As(V) to decrease significantly. The kinetic data showed that a sharp initial uptake of arsenic reached its equilibrium state within about 50 min of contact time, and the sorption kinetics followed a pseudo-second-order rate law both for As(III) and As(V) sorption. A 1,000 times increase in the background electrolyte concentration, i.e., NaNO₃, caused a significant decrease in As(III) removal, whereas As(V) was almost unaffected, which inferred that As(III) was adsorbed, mainly by the van der Waals or even by the electrostatic attraction, whereas As(V) was adsorbed chemically and formed “inner-sphere” complexes at the solid/solution interface. The equilibrium state modeling studies indicated that the sorption data fitted well the Freundlich and Langmuir adsorption isotherms. Henceforth, the removal capacity was calculated under these equilibrium conditions. It was noted that organo-modified sericite possessed a significantly higher removal capacity compared to its virgin sericite. Between these two organo-modified sericite, the HDTMA-modified sericite possessed a higher removal capacity compared to the AMBA-modified sericite.     

Behavior and mechanism of arsenate adsorption on activated natural siderite: evidences from FTIR and XANES analysis

Activated natural siderite (ANS) was used to investigate its characteristics and mechanisms of As(V) adsorption from aqueous solution. Batch tests were carried out to determine effects of contact time, initial As(V) concentration, temperature, pH, background electrolyte, and coexisting anions on As(V) adsorption. Arsenic(V) adsorption on ANS well-fitted pseudo-second-order kinetics. ANS showed a high-adsorption capacity of 2.19 mg/g estimated from Langmuir isotherm at 25 °C. Thermodynamic studies indicated that As(V) adsorption on ANS was spontaneous, favorable, and endothermic. ANS adsorbed As(V) efficiently in a relatively wide pH range between 2.0 and 10.0, although the removal efficiency was slightly higher in acidic conditions than that in basic conditions. Effects of background electrolyte and coexisting anions were not significant within the concentration ranges observed in high As groundwater. Results of XRD and Fe K-edge XANES analysis suggested ANS acted as an Fe(II)/(III) hybrid system, which was quite effective in adsorbing As from aqueous solution. There was no As redox transformation during adsorption, although Fe(II) oxidation occurred in the system. Two infrared bands at 787 and 872 cm^?1 after As(V) adsorption suggested that As(V) should be predominantly adsorbed on ANS via inner-sphere bidendate binuclear surface complexes.     

As(V) adsorption on amorphous iron oxide: Triple layer modelling

The adsorption of As(V) by amorphous iron oxide was investigated at 25°C, 0.01 M NaNO₃ background electrolyte as a function of solution pH(4–10) at three initial As(V) concentrations and two Fe(III) concentrations. As(V) adsorption increased with decreasing pH. A modified Langmuir isotherm has been used for describing an equilibrium partition existing between solid and liquid phases. The triple-layer model was used for simulating As(V) adsorption on iron oxide surface. This model was able to describe As(V) adsorption over the pH range 4–10, all at the concentrations of As(V) and Fe(III) studied. =Fe(H₂AsO₄)⁰, = Fe(HAsO₄)⁻ and = Fe(AsO₄)²⁻ have been shown through simulation with inner-sphere complexation products to be more consistent with experimental adsorption observations than complexation with other surface species.     

Thermodynamic and kinetic studies of As(V) removal from water by zirconium oxide-coated marine sand

Arsenic contamination of groundwater is a major threat to human beings globally. Among various methods available for arsenic removal, adsorption is fast, inexpensive, selective, accurate, reproducible and eco-friendly in nature. The present paper describes removal of arsenate from water on zirconium oxide-coated sand (novel adsorbent). In the present work, zirconium oxide-coated sand was prepared and characterised by infrared and X-ray diffraction techniques. Batch experiments were performed to optimise different adsorption parameters such as initial arsenate concentration (100–1,000 μg/L), dose (1–8 g/L), pH of the solution (2–14), contact time (15–150 min.), and temperature (20, 30, 35 and 40 °C). The experimental data were analysed by Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models. Furthermore, thermodynamic and kinetic parameters were evaluated to know the mode of adsorption between ZrOCMS and As(V). The maximum removal of arsenic, 97 %, was achieved at initial arsenic concentration of 200 μg/L, after 75 min at dosage of 5.0 g/L, pH?7.0 and 27?±?2 °C. For 600 μg/L concentration, the maximum Langmuir monolayer adsorption capacity was found to be 270 μg/g at 35 °C. Kinetic modelling data indicated that adsorption process followed pseudo-second-order kinetics. The mechanism is controlled by liquid film diffusion model. Thermodynamic parameter, ΔH°, was ?57.782, while the values of ΔG° were ?9.460, ?12.183, ?13.343 and ?13.905 kJ/mol at 20, 30, 35 and 40 °C, respectively, suggesting exothermic and spontaneous nature of the process. The change in entropy, ΔS°?=??0.23 kJ/mol indicated that the entropy decreased due to adsorption of arsenate ion onto the solid adsorbent. The results indicated that the reported zirconium oxide-coated marine sand (ZrOCMS) was good adsorbent with 97 % removal capacity at 200 μg/L concentration. It is interesting to note that the permissible limit of arsenic as per World Health Organization is 10 μg/L, and in real situation, this low concentration can be achieved through this adsorbent. Besides, the adsorption capacity showed that this adsorbent may be used for the removal of arsenic from any natural water resource.     

Characterizing As(III,V) adsorption by soils surrounding ash disposal facilities

Leachate derived from unlined coal ash disposal facilities is a potential anthropogenic source of arsenic to the environment. To establish a theoretical framework for predicting attenuation of arsenic by soils subject to ash landfill leachate, which is typically enriched in calcium and sulfate, the adsorption of As(V) and As(III) was characterized from 1 mM CaSO₄ for 18 soils obtained down-gradient from three ash landfill sites and representing a wide range in soil properties. As(V) consistently exhibited an order of magnitude greater adsorption than As(III). As(V) adsorption was best described by coupling pH with 15 s DCB-Fe (R² = 0.851,  = 0.001), although pH coupled to clay, DCB-Fe, or DCB-Al also generated strong correlations. For As(III), pH coupled to Ox–Fe (R² = 0.725,  = 0.001) or Ox–Fe/Al (R² = 0.771,  = 0.001) provided the best predictive relationships. Ca²⁺ induced increases in As(V) adsorption whereas sulfate suppressed both As(V) and As(III) adsorption. Attenuation of arsenic from ash leachate agreed well with adsorption measured from 1 mM CaSO₄ suggesting that the use of 1 mM CaSO₄ in laboratory adsorption tests is a reasonable approach for estimating arsenic behavior in soils surrounding ash landfills. We also showed that the impact of leachate-induced changes in soil pH over time may not be significant for As(V) adsorption at pH < 7; however, As(III) adsorption may be impacted over a wider pH range especially if phyllosilicate clays contribute significantly to adsorption. The benefits and limitations of predicting arsenic mobility using linearized adsorption coefficients estimated from nonlinear adsorption isotherms or from the relationships generated in this study are also discussed.     

Adsorption characteristics of Ni(II) on gamma-type alumina particles and its determination of overall adsorption rate by a differential bed reactor

The adsorption experiment of nickel ion [Ni(II)] on gamma-type alumina by a differential bed reactor in aqueous solutions was investigated to determine the adsorption characteristics and overall adsorption rate. The adsorbed amount increased rapidly with pH from pH 2 to 6 and kept constant over pH 6. The adsorbed amount of Ni(II) increased with temperature from 20 to 50 degrees C. Correlation coefficients (R2) of Langmuir and Freundlich adsorption isotherms were 0.9268 and 0.9489, respectively, and Freundlich isotherm was more suitable for adsorption on gamma-type alumina than Langmuir isotherm.The overall adsorption rate of Ni(II) on gamma-type alumina at pH 6 by a differential bed rector was determined as follows: r = 68.77Ce(1.61) - 17.60qe(0.36). Al(III) ions in solutions were away from the alumina surface during the adsorption of Ni(II) and Al(III) concentration increased with an increasing Ni(II) adsorbed amount on alumina.     

Mechanisms of chromium and arsenite adsorption by amino-functionalized SBA-15

The adsorption of Cr(VI) and As(III) by amino-functionalized SBA-15 (NH₂-SBA-15) from single and binary systems were investigated in this work. The effects of pH and temperature on the adsorption of NH₂-SBA-15 were studied. Adsorption kinetics, isotherm model, and thermodynamics were studied to analyze the experimental data. pH 2 was the optimum condition for the adsorption of Cr(VI) and pH 4 for As(III) adsorption. Increasing temperature had a positive effect on the removal of both Cr(VI) and As(III). The Freundlich isotherm model can depict the adsorption process best. The pseudo-second-order kinetic model fitted well with the kinetic data of Cr(VI) and As(III) in the single-component system. In the binary system, the adsorption of As(III) by NH₂-SBA-15 was slightly enhanced with the presence of Cr(VI); however, As(III) had no obvious effect on the removal of Cr(VI). Regeneration experiments indicated that 0.1 mol/L NaHCO₃ was an efficient desorbent for the recovery of Cr(VI) and As(III) from NH₂-SBA-15; the desorption rates for Cr(VI) and As(III) were 91.6 and 33.59 %, respectively. After five recycling cycles, the removal rates were 88 and 7 % for Cr(VI) and As(III) adsorption by NH₂-SBA-15, respectively.     

Arsenic(III) removal by adsorption on sawdust carbon

Studies on the removal of As(III) by adsorption on sawdust and sawdust carbon have been carried out at room temperature (25 ± 1°C). The adsorption isotherm of As(III) on sawdust carbon was obtained in a batch reactor. The process of uptake follows the first-order adsorption rate expression and obeys the Langmuir and Freundlich model of adsorption. The mass transfer coefficients as a function of initial sorbate concentration have been determined. Parameters such as pH and absorbent dose were studied. Maximum adsorption capacity was observed at pH 7.0.     

Competitive adsorption and desorption of arsenate,vanadate, and molybdate onto the low-cost adsorbent materials alum water treatment sludge and bauxite

When low-cost adsorbents are being used to remove contaminant ions (e.g. arsenate, vanadate, and molybdate) from wastewater, competitive adsorption/desorption are central processes determining their removal efficiency. Competitive adsorption of As, V, and Mo was investigated using equimolar oxyanion concentrations in single, binary, and tertiary combinations in adsorption isotherm and pH envelope studies while desorption of previously adsorbed oxyanions was examined in solutions containing single and binary oxyanion combinations. The low-cost adsorbent materials used were alum water treatment sludge (amorphous hydroxy-Al) and bauxite ore (crystalline Al oxides). Adsorption isotherm and pH envelope studies showed that Mo had only a small effect in decreasing adsorption of As and V but V and As had substantial and similar effects in reducing adsorption of the other. As had a greater effect than V in reducing adsorption of Mo and it was concluded that the affinity of oxyanions for the surfaces of water treatment sludge and bauxite followed the order As > V >> Mo. In 0.3 M NaCl electrolyte, desorption of previously adsorbed oxyanions amounted to 0.3–3.4% for V and As, and 11–20% for Mo. As had approximately four times greater effect than Mo in increasing desorption of V while V had about three times the effect of Mo in increasing desorption of As. Thus, the order of oxyanions in inducing desorption of the other oxyanions (i.e. As on V and As) was the same as that for adsorption selectivity: As > V >> Mo. Water treatment sludge was a more effective adsorbent than bauxite because it had a greater adsorption capacity for all three anions and, in addition, they were held more strongly so desorption in the background electrolyte was proportionately less. It was concluded that at similar molar concentrations, arsenate would tend to reduce adsorption of vanadate as well as displace vanadate already held on adsorbent surfaces while both anions will compete effectively with molybdate. The limiting factor for simultaneous removal of As, V, and Mo from multielement solutions by adsorption will therefore be the removal of Mo.     

As(V) retention on soils and forest by-products and other waste materials

As(V) retention capacity is determined by means of adsorption/desorption trials performed for coarse and fine ground mussel shell, forest and vineyard soils with or without fine shell, pine wood ash, oak wood ash, pine sawdust and slate-processing fines. Pine ash shows the highest arsenic retention potential (with >97 % adsorption and ≤1 % desorption), followed by shell-amended forest soil (adsorption between 96 and 92 %), by un-amended forest soil (adsorption between 98 and 86 %) and by the amended vineyard soil (adsorption between 92 and 75 %). Sawdust is the material with the lowest arsenic retention capacity in most cases, with un-amended vineyard soil also showing poor results. In the case of oak ash, As(V) percentage adsorption becomes higher with increasing added arsenic concentrations, while this increase in added arsenic causes lower percentage adsorption in the case of slate fines. Regarding adsorption ability, As(V) adsorption data were fitted to Freundlich and Langmuir models, showing good fitting, with pine ash and shell-amended forest soil having the highest K _F values. In view of that, mussel shell amendment would be useful to increase arsenic retention on forest and vineyard soils, while pine ash could be used to retain arsenic even from wastewaters.     

On the mechanistic modeling of As(III) adsorption on gibbsite

Arsenite adsorption on gibbsite was examined as a function of pH, ionic strength (I) and contact time (t(C)). As(III) showed a weak affinity for gibbsite surface. The trends of pH=f(Gamma(ads)) curves have showed a marked deviation from a typical anion adsorption edge showing a maximum Gamma(ads) around pH approximately 8.2. The experimentally derived proton exchange ratio has always converged to zero when 0.26< summation operator [As(III)]<7 microM and 6.2相似文献   

Removal of arsenic(III,V) by a granular Mn-oxide-doped Al oxide adsorbent: surface characterization and performance

In order to remove arsenic (As) from contaminated water, granular Mn-oxide-doped Al oxide (GMAO) was fabricated using the compression method with the addition of organic binder. The analysis results of XRD, SEM, and BET indicated that GMAO was microporous with a large specific surface area of 54.26 m^2/g, and it was formed through the aggregation of massive Al/Mn oxide nanoparticles with an amorphous pattern. EDX, mapping, FTIR, and XPS results showed the uniform distribution of Al/Mn elements and numerous hydroxyl groups on the adsorbent surface. Compression tests indicated a satisfactory mechanical strength of GMAO. Batch adsorption results showed that As(V) adsorption achieved equilibrium faster than As(III), whereas the maximum adsorption capacity of As(III) estimated from the Langmuir isotherm at 25 °C (48.52 mg/g) was greater than that of As(V) (37.94 mg/g). The As removal efficiency could be maintained in a wide pH range of 3~8. The presence of phosphate posed a significant adverse effect on As adsorption due to the competition mechanisms. In contrast, Ca²⁺ and Mg²⁺ could favor As adsorption via cation-bridge involvement. A regeneration method was developed by using sodium hydroxide solution for As elution from saturated adsorbents, which permitted GMAO to keep over 75% of its As adsorption capacity even after five adsorption–regeneration cycles. Column experiments showed that the breakthrough volumes for the treatment of As(III)-spiked and As(V)-spiked water (As concentration = 100 μg/L) were 2224 and 1952, respectively. Overall, GMAO is a potential adsorbent for effectively removing As from As-contaminated groundwater in filter application.

     

Alginate beads containing water treatment residuals for arsenic removal from water—formation and adsorption studies

Water treatment residuals (WTRs) produced in large quantities during deironing and demanganization of infiltration water, due to high content of iron and manganese oxides, exhibit excellent sorptive properties toward arsenate and arsenite. Nonetheless, since they consist of microparticles, their practical use as an adsorbent is limited by difficulties with separation from treated solutions. The aim of this study was entrapment of chemically pretreated WTR into calcium alginate polymer and examination of sorptive properties of the obtained composite sorbent toward As(III) and As(V). Different products were formed varying in WTR content as well as in density of alginate matrix. In order to determine the key parameters of the adsorption process, both equilibrium and kinetic studies were conducted. The best properties were exhibited by a sorbent containing 5 % residuals, formed in alginate solution with a concentration of 1 %. In slightly acidic conditions (pH 4.5), its maximum sorption capacity was 3.4 and 2.9 mg g^?1 for As(III) and As(V), respectively. At neutral pH, the adsorption effectiveness decreased to 3.3 mg As g^?1 for arsenites and to 0.7 mg As g^?1 for arsenates. The presence of carboxylic groups in polymer chains impeded in neutral conditions the diffusion of anions into sorbent beads; therefore, the main rate-limiting step of the adsorption, mainly in the case of arsenates, was intraparticle diffusion. The optimal condition for simultaneous removal of arsenates and arsenites from water by means of the obtained composite sorbent is slightly acidic pH, ensuring similar adsorption effectiveness for both arsenic species.     

Comparative and competitive adsorption of Cr(VI), As(III), and Ni(II) onto coconut charcoal

This study evaluates the behavior of coconut charcoal (AC) to adsorb Cr(VI), As(III), and Ni(II) in mono- and multicomponent (binary and ternary) systems. Batch experiments were carried out for mono- and multicomponent systems with varying metal ion concentrations to investigate the competitive adsorption characteristics. The adsorption kinetics followed the mechanism of the pseudo-second-order equation in both single and binary systems, indicating chemical sorption as the rate-limiting step of adsorption mechanism. Equilibrium studies showed that the adsorption of Cr(VI), As(III), and Ni(II) followed the Langmuir model and maximum adsorption capacities were found to be 5.257, 0.042, and 1.748 mg/g, respectively. In multicomponent system, As(III) and Ni(II) adsorption competed intensely, while Cr(VI) adsorption was much less affected by competition than As(III) and Ni(II). With the presence of Cr(VI), the adsorption capacities of As(III) and Ni(II) on AC were higher than those in single system and the metal sorption followed the order of Ni(II)?>?As(III)?>?Cr(VI). The results from the sequential adsorption–desorption cycles showed that AC adsorbent held good desorption and reusability.     

SDS改性沸石吸附结晶紫简

以表面活性剂十二烷基硫酸钠（SDS）对沸石进行改性,改性后的沸石对结晶紫溶液进行吸附,以紫外可见分光光度计分析最佳吸附条件。实验结果表明,在30℃,SDS改性沸石投入量为0.25 g;吸附平衡时间为1 h;pH为8的条件下,对含50 mg/L结晶紫染料的去除率可达到92.6%,吸附量达到4.63 mg/g。SDS改性沸石吸附结晶紫的等温吸附曲线与Henry型和Freundlich型均拟合较好。热力学参数计算结果表明,吸附符合自发吸热过程。     

载钴活性焦对As(V)的吸附性能与去除效果

使用沉淀负载法制备了载钴活性焦,并研究了溶液pH值、反应时间、As(V)初始浓度以及共存阴离子等对载钴活性焦吸附去除水环境中As(V)的影响。结果表明,(1)载钴后活性焦的比表面积和孔容积分别提高了20.87%和43.47%;(2)载钴活性焦对As(V)最佳吸附pH值为4.0,当As(V)的初始浓度为10 mg/L时,As(V)去除率可达97%;(3)吸附过程符合准二级动力学模型(k2=0.66,R2=0.96),吸附等温线为Freundlich型(kF=8.227,1/n=0.396,R2=0.97);(4)稳定性实验验证了载钴活性焦的稳定性,钴不易脱附,最大脱附率仅为0.145%。     

The role of Mn oxide doping in phosphate removal by Al-based bimetal oxides: adsorption behaviors and mechanisms

This study investigated the behaviors and mechanisms of phosphate adsorbed onto manganese (Mn) oxide-doped aluminum (Al) oxide (MODAO). The isotherm results demonstrated that the maximum amount of phosphorus (P) adsorbed onto MODAO was 59.8 mg/g at T?=?298 K (pH 6.0). This value was nearly twice the amount of singular AlOOH and could increase with rising temperatures. The kinetic results illustrated that most of the P was adsorbed onto MODAO within 5 h, which was shorter than the equilibrium time of phosphate adsorption onto AlOOH. The Elovich model effectively described the adsorption kinetic data of MODAO because of its heterogeneous surface. The optimal solution pH for phosphate removal was approximately 5.0 because of electrostatic interaction effects. Meanwhile, the decrease in P uptake with increasing ion strength suggested that phosphate adsorption occurred through an outer-sphere complex. Phosphates would compete for adsorption sites on the surface of MODAO in the presence of fluoride ion or sulfate. In addition, the spectroscopic analysis results of Fourier transform infrared spectroscopy and X-ray photoemission spectroscopy indicated that removal mechanisms of phosphate primarily include adhesion to surface hydroxyl groups and ligand exchange.     

As(V) and Sb(V) co-adsorption onto ferrihydrite: synergistic effect of Sb(V) on As(V) under competitive conditions

Competitive adsorption of As(V) and Sb(V) at environmentally relevant concentrations onto ferrihydrite was investigated. Batch experiments and XPS analyses confirmed that in a binary system, the presence of Sb(V) exhibited a slight synergistic effect on As(V) adsorption. XPS analyses showed that As(V) and Sb(V) adsorption led to obvious diminishment of Fe–O–Fe and Fe–O–H bonds respectively. At pH of 9, a more significant decrease of Fe–O–Fe was observed in the binary system than that in a single system, indicating that As(V) displayed an even stronger interaction with lattice oxygen atoms under competitive conditions. Basically, ionic strength demonstrated a negligible or positive influence on As(V) and Sb(V) adsorption in binary system. Study of adsorption sequence also indicated that the presence of Sb(V) showed a promotion effect on As(V) adsorption at neutral pHs. Considering that co-contamination of As and Sb in waters has been of great concern throughout the world, our findings contributed to a better understanding of their distribution, mobility, and fate in environment.