Effective removal of coordinated copper from wastewater using a new dithiocarbamate-type supramolecular heavy metal precipitant

A new dithiocarbamate-type heavy metal precipitant, sodium 1,3,5-hexahydrotriazinedithiocarbamate (HTDC), was prepared and used to remove coordinated copper from wastewater. In the reported dithiocarbamate-type precipitants, HTDC possesses the highest percentage of the effective functional groups. It could effectively precipitate copper to less than 0.5 mg l⁻¹ from both synthetic and actual industrial wastewater containing CuEDTA in the range of pH 3–9. UV–vis spectral investigation and elemental analysis suggested that the precipitate was a kind of coordination supramolecular compound, [Cu₃(HTDC)₂]_n. The toxicity characteristic leaching procedure (TCLP) and semi-dynamic leaching test (SDLT) indicated that the supramolecular precipitate was non-hazardous and stable in weak acid and alkaline conditions. Tests of an anion exchange resin D231 provided a clue to simultaneously remove excess HTDC and residual CuEDTA in practical process of wastewater treatment.     

Comparisons of metal leachability for various wastes by extraction and leaching methods

The objective of this research was to evaluate three extraction tests, i.e., toxicity characteristic leaching procedures (TCLP), extraction procedure (EP), and American Society for Testing and Materials (ASTM) methods, for their ability to extract metals in chemical sludge and incineration bottom ash, in terms of the precision of analytical results. Typical chemical sludges, including the electroplating and dye-stuff sludges, the municipal solid waste incineration bottom ash, the leather debris, and the steel-mill bottom residue containing Cd, Cr, Cu, Pb, and Zn were prepared for the lysimetry test (dynamic testing) to compare with the extraction results. Results show that for bottom residue and dye-stuff sludge, the concentration of metal leached was almost the same between the lysimetry leaching and the TCLP tests. The metal concentration followed the order: TCLP approximately = EP > ASTM. TCLP and EP exhibited almost the same relative standard deviation (RSD) value. Therefore, the results of the TCLP tests for bottom residue and dye-stuff sludge, which have a low metal content and alkalinity, can be used to estimate the metal concentration leached by typical acid rain in Taiwan; whereas the ASTM extraction test may be a better indicator of the lysimetry test.     

Fractionation and mobility of metals in bauxite red mud

Red mud (RM) is a strongly alkaline residue generated in enormous amounts worldwide from bauxite refining using the Bayer chemical process. RM is composed mainly of Fe, Ti and Al oxides and hydroxides, but it also contains an array of trace metals and metalloids at different concentrations. The purpose of this paper is to assess the potential mobility of metals in RM, with special emphasis on pH effect. The ‘operational’ distribution and leachability of metals within/from RM was studied by applying a sequential extraction procedure (SEP) and several leaching tests (rapid titration, equilibration acidification, batch leaching with acetic acid and also the toxicity characteristics leaching procedure (TCLP) and the DIN 38414-S4 procedures, used as reference methods) carried out at different pH, solid/liquid ratio, extraction period and type of acid (HCl or acetic acid). Chemical analysis showed that, in addition to the major metals Fe, Al and Ti, RM contains several trace metals, some of them (Cr, Cu and Ni) in concentrations exceeding the regulatory limits. SEP showed that a majority of the metals in the RM (between the 32.2?±?8.5 for Cd and 95.3?±?0.4 % for Ni) were found in the residual fraction, suggesting that they are not readily mobile under normal environmental conditions. Leaching tests performed at different pH showed that a significant fraction of the metals is mobilised from RM only under very strong acid conditions (pH?<?2), whereas Al is released in considerable amounts at pH?<?5.3. Among the trace metals, Cr requires special attention because of its relative high concentration in RM and the higher concentrations of this metal mobilised at low pH. The leaching tests using acetic acid showed that the standard TCLP largely underestimates the release of trace metals from RM, and therefore it is not advisable to evaluate the actual potential leaching of trace metals from this residue.     

Evaluation of the stability of arsenic immobilized by microbial sulfate reduction using TCLP extractions and long-term leaching techniques

An investigation was conducted to evaluate the stability or leachability of arsenic immobilized by microbial sulfate reduction. Anoxic solid-phase samples taken from a bioreactor previously used to treat metal and As contaminated water using sulfate reducing bacteria (SRB) were subjected to the toxicity characteristic leaching procedure (TCLP) and long-term column leaching tests. The results from TCLP experiments showed that the concentration of As leached from solid-phase sulfide material (SSM) samples after an 18 h extraction time was <300 microgl(-1), which is below the current maximum Australian TCLP leachate value for As, and thus would not be characterized as a hazardous waste. In terms of percent total As leached, this was equivalent to <8.5% for SSM samples initially containing 61.3 mgkg(-1) As. The levels of As extracted by the TCLP was found to be significantly lowered or underestimated in the presence of dissolved oxygen, with As concentrations increasing with decreasing headspace-to-leachant volume ratios. The concentration of As was also consistently higher in nitrogen purged extractions compared to those performed in air. This was attributed to the dissolution of Fe-sulfide precipitates and subsequent oxidation of Fe(II) ions and precipitation of ferric(hydr)oxides, resulting in the adsorption of soluble As and corresponding decrease in As concentrations. According to the experimental data, it is recommended that TCLP tests for As leachability should be performed at least in zero-headspace vessels or preferably under nitrogen to minimize the oxidation of Fe(II) to ferric(hydr)oxides. In long-term leaching studies (approximately 68 days), it was found that the low solubility of the SSM ensured that rate of release of As was relatively slow, and the resulting leachate concentrations of As were below the current Australian guideline concentration for arsenic in drinking water.     

The effect of copper speciation on the formation of chlorinated aromatics on real municipal solid waste incinerator fly ash

A limited amount of information exists regarding the relationship between the chemical form of copper and the formation of chlorinated aromatics in fly ash. To understand the effects of the various forms of copper on the formation of chlorinated aromatics in real fly ash, we determined the chemical forms of copper present in various types of real fly ash using X-ray absorption near edge structure (XANES) and evaluated the relationship between the chemical forms of copper and the formation of chlorinated aromatics. Copper chloride hydroxide (CuCl2 x 3Cu(OH)2) and cuprous chloride (CuCl) were the predominant copper species found in real fly ash. Although pure cupric chloride (CuCl2) is known to be the most active catalyst for the formation of chlorinated aromatics under experimental conditions with synthetic fly ash, CuCl2 was not found in every real fly ash sample. The amount of copper chloride hydroxide was positively correlated with the formation of chlorinated aromatics in real fly ash and is, consequently, considered to be one of the key species involved in the formation of chlorinated aromatics.     

含重金属水处理污泥的固化和浸出毒性研究

工业危险固体废物在进行安全填埋前需要进行固化稳定处理。针对电镀厂和皮革厂含重金属的水处理污泥 ,用不同比例的水泥、粉煤灰进行固化稳定处理。考虑酸雨环境 ,浸出实验采用TCLP标准。电镀厂污泥单独固化时 ,其浸出液中铜离子浓度由 78 0mg/L下降到 1 5mg/L ;镍离子浓度由 2 2 4 5mg/L下降到 2 2 2mg/L ,高于危险废物允许进入填埋区 15mg/L的控制限值。电镀厂污泥与皮革厂污泥混合后固化 ,浸出液毒性明显降低。铜离子的浸出浓度降低到1 98mg/L ,镍离子降低到 4 10mg/L ,总铬降低到 0 4 0mg/L ,各项指标均低于国家危险废物允许进入填埋区的控制限值 ,可安全填埋。     

Assessment of the mechanical stability and chemical leachability of immobilized electroplating waste

The effectiveness of cement based treatment technology, in immobilizing chromium laden electroplating sludge was assessed by conducting toxicity characteristic leaching procedure (TCLP). The mechanical stability of the blocks was tested by measuring the compressive strength. Other leaching tests such as NEN 7341 test, ANS 16.1 and multiple TCLP (MTCLP) test conducted on select solidified blocks showed that chromium was immobilized by the binder studied. A linear relationship was obtained between the cumulative fraction of chromium leached (CFL) and square root of time in the solidified samples proving that diffusion is the controlling mechanism for leaching of chromium. The leachability indices (LI) obtained for the solidified materials using cement and cement-fly ash system (EPC6, EPFC6A and EPFC6B) satisfy the guidance value as per US NRC, which clearly indicates that chromium is well retained within the solid matrix. Chromium concentrations in the TCLP leachates of the above mix ratios were well within the regulatory level of United States Environmental Protection Agency (USEPA). Molecular characterization of the solidified material was carried out using Fourier transformation infra red (FTIR) technique.     

Arsenic contaminated site at an abandoned copper smelter plant: waste characterization and solidification/stabilization treatment

A preliminary survey of an arsenic contaminated site from an abandoned copper smelting facility and feasibility study of using solidification/stabilization (S/S) process to treat the contaminant waste were undertaken. It was found that the waste, located in the three-flue gas discharge tunnels, contained 2-40% arsenic. The pH of the contaminated waste is extremely low (ranging from 1.8 to 3.6). The X-ray diffraction evidence indicates that the arsenic particles present in the flue gas mainly exist as As(III), or As(2)O(3). The total amount of arsenic contaminated waste is estimated to be 700 ton in the studied area. About 50% of the particle sizes are less than 2 mm. Arsenic is easily extracted from wastes with a variety of leaching solutions. In order to meet the arsenic leaching standard of the toxicity characteristic leaching procedure (TCLP), an extremely high cement dosage is required in the S/S process (cement/waste weight ratio>6). The waste with lower particle size having higher specific surface area exhibits somewhat positive effect on the S/S performance. The use of fly ash from municipal waste incinerators, in conjunction with the reduced amount of cement, is able to meet the TCLP arsenic and lead standards. The use of lime alone could meet the TCLP arsenic standard, but lead leaching concentrations exceeded leaching Pb standard. The results of semi-dynamic leaching tests of some solidified samples indicate higher accumulated arsenic leaching concentrations after only a few leachant renewals.     

Limitations of the toxicity characteristic leaching procedure for providing a conservative estimate of landfilled municipal solid waste incineration ash leaching

Limitations of the toxicity characteristic leaching procedure (TCLP) for simulating pollutant leaching from wastes disposed of in full-scale landfills are well understood in the waste management profession; the TCLP solution has a lower pH and greater organic acid content than typical landfill leachate. The TCLP serves its intended regulatory objective, however, as long as a conservative estimate of leaching is provided. Here, we examine TCLP’s ability to represent worst-case leaching conditions for monofilled municipal solid waste incineration (MSWI) ash. A critical examination of TCLP’s applicability to MSWI ash is especially relevant, as ash management at MSWI facilities often centers on passing TCLP, regardless of environmental risk posed by the ash or its recyclability. Multiple batch leaching tests were conducted on different MSWI ash streams: mixed ash, fly ash, and different size fractions of bottom ash. Batch-test results were compared with leachate simulating MSWI ash monofills. The TCLP did not consistently provide the most conservative estimate of leaching, supporting the need to consider alternative methodologies in future regulatory development.

Implications: This paper analyzes the existing hazardous waste regulatory testing requirement for municipal solid waste incinerator (MSWI) ash management to evaluate whether the TCLP serves its intended purpose in providing the most conservative estimate of landfilled MSWI ash. The results will serve as guidance and motivation for policy makers and the regulatory community to reevaluate the TCLP’s application for characterizing MSWI ash leaching in certain disposal scenarios and could promote consideration of alternative testing procedures based upon results of this study. This study serves to promote representative and accurate quantification of leaching risk from MSWI ash.     

CuCl2蚀刻液制备CuCl的研究

以氯化钢蚀刻液废液、粗铜粉等为原料,在常温下反应制备氯化亚铜,工艺简便,产品质量好,具有显著的经济效益和环境效益。     

The effect of earthworms on the fractionation, mobility and bioavailability of Pb, Zn and Cd before and after soil leaching with EDTA

The effect of two ecologically contrasting earthworm species Eisenia fetida (epigeic) and Octolasion tyrtaeum (endogeic) on the fractionation (accessed using sequential extractions), mobility (toxicity characteristic leaching procedure, TCLP) and oral bioavailability (Ruby's physiologically based extraction test, PBET) of Pb, Zn and Cd was studied before and after soil remediation with soil leaching. Twenty-step leaching, with 2.5 mmol kg(-1) EDTA used in each step, removed 58.4%, 25.0% and 68.0% of initial soil Pb, Zn and Cd, respectively, shifted the fractionation of residual heavy metals toward less labile forms, and decreased their mobility by 83.7%, 80.3%, and 90.9%. Pb oral bioavailability was reduced by 3.1-times (in each stomach and intestinal phase). After soil leaching, both earthworm species enriched the carbonate soil fraction in their casts with residual Pb, and increased the Pb bioavailability in the simulated intestinal phase by a factor of 2.4 (E. fetida) and 2.8 (O. tyrtaeum). The concentration of Pb in TCLP leachate from E. fetida casts was 6.2-times higher than in the bulk of the remediated soil. These results indicate that the effect of biotic factors on the availability of heavy metals residual in soil after soil leaching requires consideration.     

A simple and fast screening test to detect soils polluted by lead

Lead pollution is an environmental priority. The evaluation of contaminated soils was often based on the results of the toxicity characteristic leaching procedure (TCLP) or the synthetic precipitation leaching procedure (SPLP). This paper presents a simple and fast screening test to detect soil contaminated by lead. The test is based on the chemistry of the stomach (Cl- concentration, pH 2, T = 37 degrees C) and simulates the incidental oral ingestion of soil by young children. The gastric juice simulation test (GJST) and the TCLP were applied to six size fractions from five soils. The GJST solubilized more Pb (up to 169 mg/l) than the TCLP especially for the smallest size fraction. Particle size had less effect on the TCLP. The percentage of lead released with the GJST, was most significant for the <63 microm size fraction and varied from 18 to 74% of the total lead content. Lead leached during the TCLP as a function of the total lead content showed poor linear regression coefficient (R) values for soils <250 microm. R values were significant for all size fractions with the GJST. The pH of approximately 5 in the TCLP limits the solubilization of lead in the small size fractions. The five soils exceeded the toxicity threshold of 10 microgPb/dl of blood for a significant fraction of children between 0 and 36 months using the EPA's IEUBK model (Integrated Exposure Uptake Biokinetic). But the TCLP did not detect lead contamination in two of these five soils. The GJST proved to be a better estimator of lead bioaccessibility in the gastrointestinal tract.     

Arsenic leachability and speciation in cement immobilized water treatment sludge

Arsenic leachability and speciation in cement immobilized water treatment sludge were investigated with leaching tests and X-ray absorption near edge structure (XANES) spectroscopy. The As leachability in the sludge determined with the toxicity characteristic leaching procedure (TCLP) and the waste extraction test (WET) was 283 and 7490 microgl(-1), respectively. Extractions with a lower liquid to solid ratio, under anaerobic conditions, and using citric acid buffer solution dramatically increased the leachate As concentration. XANES results showed that the As(III) composition was reduced from 51.1% of the total As content in the sludge to 16.3% in the cement treated sample with 28 days of cure. When the cement treated sample was cured for two years, the As(III) composition was decreased to 7.4%. The cement treatment reduced the As leachability. The leachate As(III) and total As concentrations were of the same order of magnitude in the samples cured for 28 days as for 2yr. However, consistently lower concentrations were detected in samples with longer cure time. The results of this study improve our understanding of arsenic speciation and leachability in the cement matrix after long cure times.     

Initiatives to reduce lead from electronic devices: evidence of success from the toxicity characteristic leaching procedure

Discarded electronic devices (E-waste) have historically been found to exceed US Toxicity Characteristic hazardous waste thresholds for lead. Research was conducted to assess whether global and national lead reduction initiatives in the past decade translate to reduced toxicity characteristic leaching procedure (TCLP) lead leaching from E-waste. Nine categories of devices were subjected to TCLP and in all devices except one (smoke detectors), mean TCLP lead concentration results decreased by an order of magnitude or more (to levels below regulation thresholds). Mean TCLP lead concentrations decreased from 29.1 mg/L (2000–2005) to 0.224 mg/L (2008+) for cell phones and 1.26 mg/L (2000–2005) to 0.060 mg/L (2008+) for PCs. Most recently manufactured electronic devices (of those types tested here) comply with the definition of non-hazardous waste under US regulations.

Implications: Discarded electronic devices (E-waste) have often been tested as hazardous waste in the US because of lead leaching. Toxicity characteristic leaching procedure (TCLP) testing on more recently manufactured devices reveals that global lead reduction efforts have resulted in newer devices complying with US non-hazardous waste definitions. While these results highlight the success of lead reduction efforts, they raise policy questions regarding how best to incentivize E-waste recycling going forward.     

石灰干化污泥对土壤重金属稳定化处理的效果

以采自湖南省嘉禾县重金属复合污染土壤为研究对象,采用城市污水处理石灰干化污泥作为稳定剂,对污染土壤进行稳定化处理,并采用TCLP和BCR连续提取法对稳定化效果进行分析和评价。研究结果表明,单独使用石灰干化污泥,TCLP浸出浓度随着干化污泥质量分数的增加而显著减少,干化污泥的质量分数为40%时,稳定化率最大为Zn-98.92%、Cd-99.06%、Pb-96.84%;但是干化污泥的高pH值导致稳定后土壤中As的浸出增加。为了恢复植物生长功能,经过亚铁盐和磷酸调节pH后,石灰干化污泥稳定过的土壤pH有效降低,同时亚铁盐和磷酸有利于促进Pb和Zn的稳定效果;但是对Cd的稳定有负面影响;另外,亚铁盐的加入同时可以减少As的浸出浓度。经处理后土壤中重金属形态由不稳定态转为稳定态,使重金属的浸出浓度明显降低,减少了土壤重金属的浸出毒性。该研究结果表明,石灰干化污泥可以作为资源回收利用,应用于重金属污染土壤的修复中,并能改善稳定后土壤适宜植物生长的理化性质。     

Effects of copper(II) and copper oxides on THMs formation in copper pipe

Little is known about how the growth of trihalomethanes (THMs) in drinking water is affected in copper pipe. The formation of THMs and chlorine consumption in copper pipe under stagnant flow conditions were investigated. Experiments for the same water held in glass bottles were performed for comparison. Results showed that although THMs levels firstly increased in the presence of chlorine in copper pipe, faster decay of chlorine as compared to the glass bottle affected the rate of THMs formation. The analysis of water phase was supplemented by surface analysis of corrosion scales using X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM) and energy dispersive spectroscopy (EDX). The results showed the scales on the pipe surface mainly consisted of Cu₂O, CuO and Cu(OH)₂ or CuCO₃. Designed experiments confirmed that the fast depletion of chlorine in copper pipe was mainly due to effect of Cu₂O, CuO in corrosion scales on copper pipe. Although copper(II) and copper oxides showed effect on THMs formation, the rapid consumption of chlorine due to copper oxide made THM levels lower than that in glass bottles after 4 h. The transformations of CF, DCBM and CDBM to BF were accelerated in the presence of copper(II), cupric oxide and cuprous oxide. The effect of pH on THMs formation was influenced by effect of pH on corrosion of copper pipe. When pH was below 7, THMs levels in copper pipe was higher as compared to glass bottle, but lower when pH was above 7.     

Eisenia fetida avoidance behavior as a tool for assessing the efficiency of remediation of Pb, Zn and Cd polluted soil

Remediation by means of soil leaching with ethylenediaminetetraacetic acid (EDTA) is capable of extracting the most labile soil fractions, leaving the residual metals in biologically non-available forms. We evaluated the feasibility of the standardized earthworm (Eisenia fetida) avoidance test for assessing the efficiency of soil remediation of Pb, Zn and Cd polluted soil. Chemical extraction tests (six-step sequential extraction, toxicity characteristic leaching procedure, physiologically based extraction test, diethylenediaminepentaacetic acid extraction) indicated that the mobility, oral bioaccessibility and phytoavailability of Pb, Zn and Cd were consistently reduced. However, the avoidance test showed no significant avoidance of polluted soil in favor of that which had been remediated. Pb, Zn and Cd accumulation in E. fetida mirrored the decreasing pattern of metal potential bioavailability gained by leaching the soil with increasing EDTA concentrations. The calculated bioaccumulation factors indicated the possibility of underestimating the metal bioavailability in soil using chemical extraction tests.     

Immobilization of lead in contaminated firing range soil using biochar

Soybean stover-derived biochar was used to immobilize lead (Pb) in military firing range soil at a mass application rate of 0 to 20 wt.% and a curing period of 7 days. The toxicity characteristic leaching procedure (TCLP) was performed to evaluate the effectiveness of the treatment. The mechanism responsible for Pb immobilization in military firing range soil was evaluated by scanning electron microscopy-energy dispersive x-ray spectroscopy (SEM-EDX) and x-ray absorption fine structure (XAFS) spectroscopy analyses. The treatment results showed that TCLP Pb leachability decreased with increasing biochar content. A reduction of over 90 % in Pb leachability was achieved upon treatment with 20 wt.% soybean stover-derived biochar. SEM-EDX, elemental dot mapping and XAFS results in conjunction with TCLP leachability revealed that effective Pb immobilization was probably associated with the pozzolanic reaction products, chloropyromorphite and Pb-phosphate. The results of this study demonstrated that soybean stover-derived biochar was effective in immobilizing Pb in contaminated firing range soil.     

Alkali borosilicate glass by fly ash from a coal-fired power plant

The possibility of using coal fly ash as a silica source for alkali borosilicate glass was investigated. Alkali borosilicate glasses were prepared from the coal fly ash mixed with 30 wt.% reagents composed of Na(2)O and B(2)O(3) by susceptor-induction heating. Their densities ranged from 2.24 to 2.55 g cm(-3) and decreased as the amount of B(2)O(3) addition increased. However, the Vickers microhardness showed a different tendency with the density since the glass network connectivity improved by boron anomaly, which was identified by a nuclear magnetic resonance analysis. The Vickers microhardness of the glass product, with the addition of 15 wt.% B(2)O(3) and 15 wt.% Na(2)O, was about 4030 MPa. Furthermore, the changes in microstructure were consistent with those in the chemical stability by the toxicity characteristic leaching procedure (TCLP).     

村镇小型生活垃圾热处理炉底渣的理化特性

小型垃圾热处理设备可实现就地处置,节约运输成本,目前在中国山区、丘陵地带的村镇得到广泛应用.为了解村镇小型生活垃圾热处理炉底渣的理化特性及其影响因素,对中国云南、贵州、安徽村镇实际运行的小型生活垃圾热处理设备产生的底渣进行取样,分析其热灼减率、物理组成、化学组成、晶相组成、重金属含量和浸出特性,探讨处理工艺、地域及季节...