铁炭微电解-水解酸化-接触氧化法处理有机硅废水的研究

针对有机硅废水的特性,采用铁炭微电解预处理、水解酸化和接触氧化组合工艺处理有机硅废水。废水经铁炭微电解预处理后COD去除率达40%;水解酸化处理后COD去除率达30%;接触氧化处理后COD去除率达70%;当系统进水COD为750 mg/L时,经过组合工艺处理后,出水COD可降至100 mg/L以下,达到了工业废水排放标准。     

Fenton氧化-生化组合工艺处理染料中间体废水

针对染料中间体废水具有COD高、BOD5/COD低和具有生物毒性的特性,采用Fenton氧化-水解酸化-好氧组合工艺进行染料中间体生产废水的处理试验,试验结果表明:废水经Fenton氧化及水解酸化工序后,废水的BOD5/COD值由0.03升高至0.48,经好氧生化工序处理后的出水COD和BOD5浓度分别达122.6 mg/L和54.6 mg/L,符合《污水综合排放标准》(GB8978-1996)二级标准,该组合工艺COD总去除率达94%.     

臭氧催化氧化-BAF组合工艺深度处理抗生素制药废水

针对抗生素制药废水组分复杂、毒性强、难生物降解的特点,以Ce负载天然沸石作为催化剂(Ce/NZ),采用臭氧催化氧化-曝气生物滤池(BAF)组合工艺对抗生素制药废水二级生化处理出水进行深度处理。结果表明,Ce/NZ催化剂可显著改善臭氧预处理单元的处理效率,在臭氧进气浓度为50 mg·L~(-1)、臭氧进气量为600 mL·min~(-1)、催化剂用量为1 g·L~(-1)、臭氧反应时间为120 min的条件下,臭氧催化氧化预处理对抗生素制药废水的COD去除率达到43%,平均COD由220 mg·L~(-1)降至125 mg·L~(-1),BOD_5/COD由0.12升至0.28,废水的可生化性得到显著提高。臭氧预处理单元出水采用BAF进行生化处理,在进水平均COD为125 mg·L~(-1)、平均NH_4~+-N为12 mg·L~(-1)、水力停留时间为4 h、气水比为4∶1的条件下,COD和NH_4~+-N的平均去除率分别为62%和64%。组合工艺处理后出水平均COD和NH_4~+-N分别为46 mg·L~(-1)和4.1 mg·L~(-1),出水水质可以稳定达到《发酵类制药工业水污染物排放标准》(GB 21903-2008)。相较于单独BAF工艺,组合工艺出水COD和NH_4~+-N平均去除率分别提高了66%和15%,出水水质明显优于单独BAF工艺出水。     

Fenton氧化与铁炭微电解组合预处理DMF废水

对COD表征模拟废水中DMF去除率的可行性进行了探讨。在此基础上,分别对铁炭微电解、Fenton氧化-铁炭微电解和铁炭微电解-Fenton氧化组合工艺对DMF废水的处理效果进行分析,结果表明,Fenton氧化-铁炭微电解工艺的处理效果较好。在pH=5,反应时间为1 h,FeSO4·7H2O投加量为1 000 mg/L、H2O2投加量为2.67 mL/L和不曝气的最佳反应条件下,Fenton氧化-铁炭微电解工艺对实际废水和废液中COD的去除率分别达到66.67%和72.22%,从而验证了该工艺处理DMF废水的可行性。此外,Fenton氧化处理DMF废水过程实际上是将酰胺基团和羰基的不饱和双键氧化分解的过程。     

2种组合工艺处理靛蓝废水的中试实验研究

分别采用水解酸化/好氧MBBR/BAF和水解酸化/好氧MBBR/臭氧氧化/BAF 2种组合工艺对实际靛蓝废水进行处理规模为24 m3/d的中试研究。实验结果表明,当进水COD平均初始浓度为2 100 mg/L、平均色度为90倍、系统总水力停留时间为40 h时,前一种组合工艺对COD和色度的去除率分别达93.27%和89.87%;而后一种组合工艺对COD和色度的去除率分别达97.96%和100%,工艺中臭氧氧化单元可使处理后出水中有机物的数量大大降低。表明水解酸化/好氧MBBR/臭氧氧化/BAF组合工艺处理靛蓝废水更为有效,但增加臭氧氧化单元会使每吨废水处理成本增加0.55元。     

BCO+BAF工艺深度处理洗涤剂废水

采用生物接触氧化(BCO)+曝气生物滤池(BAF)组合工艺深度处理洗涤剂废水,研究了溶解氧浓度(DO)、水力停留时间(HRT)对其处理性能的影响。实验结果表明,随着DO浓度的提高,组合工艺对COD和LAS的去除率都随之增加;水力停留时间的增加有利于对COD与LAS的去除,最佳停留时间选为21.2h为宜;在BCO段DO为3.0 mg/L,HRT为20.0 h,BAF段DO为4.0 mg/L,HRT为1.2 h的运行条件下,COD与LAS的去除率分别为90.5%和94.3%,出水COD和LAS均能达到排放标准。     

铁炭微电解/Fenton试剂预处理土霉素废水的研究

研究了铁炭微电解/Fenton试剂法工艺对高浓度难生化处理的土霉素废水预处理效果.结果表明,当原水COD在6 000 mg/L、pH值为2.2时,铁炭微电解反应时间为80 min,铁炭微电解对原水COD的去除率>40%;铁炭微电解出水再投加220 mg/L的H2O2(30%)进行Fenton试剂法处理,常温下反应50 min对原水COD的去除率可提高到75%以上.铁炭微电解 Fenton试剂联合工艺的处理效果好、运行稳定、成本低廉,适宜对难降解的土霉素废水的预处理.     

臭氧-BAF组合工艺处理电镀RO浓水

电镀废水反渗透(RO)浓水具有盐度高、难降解有机物浓度高、含重金属等特点,是电镀废水处理工艺提标改造的难点。采用臭氧-曝气生物滤池(BAF)组合工艺,对电镀废水反渗透(RO)浓水中有机物进行处理,使出水COD浓度达到《电镀污染物排放标准》中标准。考察了废水初始p H、臭氧浓度和反应时间等因素对臭氧氧化效果的影响,以及水力停留时间(HRT)和气水比对BAF单元COD去除效果的影响。经优化后的系统运行工况为:臭氧氧化单元中废水初始p H值为10.0,臭氧浓度为31.96 mg·L~(-1),反应时间为40 min;BAF的HRT为3 h,气水比为5∶1。在最佳工况下,当进水COD为180~240 mg·L~(-1)时,经组合工艺处理后COD去除率达78.6%,平均出水COD浓度为47 mg·L~(-1),达到了标准的要求。     

微波强化微电解技术处理硝基苯废水

研究了微波强化微电解组合工艺处理硝基苯废水。研究结果表明,在Fe/C比为3,进水pH=3,微波功率640W,微波辐射时间4 min和曝气量为2.5 L/min的最佳条件下,废水COD、色度和浊度去除率分别达到94.7%、95.6%和90.3%。同时,与单一微波辐射和单一微电解相比,该方法处理效果明显优于这二种方法。实验还采用GC-MS分析方法研究了单一微电解及微波强化微电解法处理硝基苯废水的中间降解产物和降解机理。     

内电解－混凝－SBR－生物炭组合工艺处理染料废水

详述用内电解—混凝—SBR—生物炭组合工艺处理染料废水的过程。通过对各工艺段的调试，确定了各工艺段的最佳控制条件。结果表明：当染料废水COD平均值为5100mg／L，色度为6000倍时，去除率达95％以上，出水水质达到国家污水综合排放二级标准。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.