Comparison of in-house-developed ELISA with HPLC techniques for the analysis of atrazine residues

In-house developed ELISA was standardized to monitor atrazine residues in different environmental samples. The standard curve was linear, indicating an increase in log concentration with decrease in absorbance (%B/B₀ = 1.075–0.042 Log C; r = ?0.966). The middle of the test was at 75 ng/L and the lowest detection limit at 4 ng/L. ELISA significantly correlated with the high performance liquid chromatography (HPLC) (r = 0.990). Internal validation showed good accuracy and precision. Maximum atrazine residues were present in Jehlum River water/sediments and maize/sugarcane plant roots. Most of the food samples were found to be contaminated. ELISA required less clean-up steps than HPLC, but showed matrix effect in soil/colored extracts.     

Development of ELISA technique for the analysis of atrazine residues in water

A highly sensitive enzyme immunoassay is described for the detection of atrazine residues in water. Atrazine derivative was conjugated to Bovine Serum Albumin (BSA) to obtain an immunizing antigen and to Horseradish Peroxidase enzyme (POD) to obtain a marker for immunoassay. The formation of these conjugations was confirmed by UV spectroscopy as well as by gel-electrophoresis. Polyclonal antibodies were raised in rabbits by immunization with an atrazine-BSA conjugate containing 29 atrazine residues per BSA molecule. An ELISA on microtitration plates was optimized with peroxidase-atrazine conjugate. The middle of the test (50% B/Bo) was found to be at 90 ng/l, which is well below the maximum concentration permitted by the EC guidelines for drinking water. Detection limits for atrazine of about 1 ng/l could be reached. The assay did not require concentration or cleanup steps for drinking or ground water samples. Validation experiments showed good accuracy and precision. No cross-reactivities were shown by other s-triazines like terbutryn, ametryn, terbuthylazine, des-isopropylatrazine, and de-ethylatrazine except hydroxyatrazine. The latter was present at very low levels that can be calibrated/standardized before analysis or it may be considered as leftover residues of atrazine. Based on these results, it is suggested that this test can be applied to obtain fairly accurate results for atrazine concentration in water samples from different sources.     

Monitoring of atrazine in milk using a rapid tube-based ELISA and validation with HPLC

Although atrazine has been banned in the European Union since 2007 it still persists in soil from where it can enter the food chain. Milk-producing animals accumulate atrazine from contaminated feed and water and since large quantities of milk and milk products are consumed its quality should be constantly monitored. The objective of this investigation was to develop a simple tube ELISA procedure suitable for use in non-specialised laboratories and in the field. A polyclonal antibody raised in sheep and the hapten-gelatine conjugate was immobilised onto polystyrene tubes. This enables the colour produced to be read on a basic spectrophotometer. Milk samples were collected from three farms in different regions of Poland and diluted before immunoassay was performed. Samples were extracted with hexane-acetone for HPLC analysis. The amount of fat in the milk samples interferes with the dose response so it essential that the standards are prepared in the same samples matrix. A good correlation between 1% and 2% was found between the two methods in the analysis of real samples. However the ELISA procedure was more sensitive that the HPLC method since atrazine was detected in some samples by the ELISA but was not confirmed by the HPLC method. The study demonstrated that the simple antigen-coated tube assay provides a cost effective and valuable screening test that can be easily modified for direct use as a screening tool in the field.     

Method of median semi-variance for the analysis of left-censored data: Comparison with other techniques using environmental data

In environmental monitoring, variables with analytically non-detected values are commonly encountered. For the statistical evaluation of these data, most of the methods that produce a less biased performance require specific computer programs. In this paper, a statistical method based on the median semi-variance (SemiV) is proposed to estimate the position and spread statistics in a dataset with single left-censoring. The performances of the SemiV method and 12 other statistical methods are evaluated using real and complete datasets. The performances of all the methods are influenced by the percentage of censored data. In general, the simple substitution and deletion methods showed biased performance, with exceptions for L/2, Inter and L/√2 methods that can be used with caution under specific conditions. In general, the SemiV method and other parametric methods showed similar performances and were less biased than other methods. The SemiV method is a simple and accurate procedure that can be used in the analysis of datasets with less than 50% of left-censored data.     

Sorption of atrazine and metolachlor by burrow linings developed in soils with different crop residues at the surface

Atrazine and metolachlor sorption by earthworm (Lumbricus terrestris L.) burrows was measured by introducing herbicides into the burrows and collecting the effluent between 0 to 3, 3 to 6, and 6 to 9 min of simulated burrow flow. On average, sorption by burrow linings reduced the herbicide concentration to 78% (atrazine) and 74% (metolachlor) of the applied herbicide solution concentration. For both herbicides, the amount sorbed was dependent on the food source available to the earthworm, as well as the duration of burrow flow. On average, soybean-fed- and corn-fed-earthworm-burrows significantly retained more herbicides relative to the Control Treatment (unfed-earthworms). More herbicides were transported through the burrows with time because the lateral flow movement from the burrow wall into the soil matrix decreased. It is also likely that herbicides retained on burrow linings during the first 3 min of flow saturated the adsorption sites on the burrow wall, which decreased the subsequent retention potential of herbicides in flow between 3 to 9 min. Based on these results, we conclude that herbicide transport through earthworm burrows in the field will be related to crop and crop residue management practices.     

Localization of atrazine non-extractable (bound) residues in soil size fractions

Three different soils were incubated under field conditions with ¹⁴C-ring labelled atrazine. After six months, the soils were exhaustively extracted with methanol and sonicated in water. The dispersed material was then fractionated by sieving, sedimentation and centrifugation, and each fraction was separated into humin, fulvic and humic acids. In all soils, the well humified organic matter and the atrazine residues were mainly located in the 20-2 and 2-0.2 μm fractions. There was a very large concentration of bound residues in the coarsest fractions, especially in the 200-50 μm fraction. These could be related to the active degradation of coarse plant residues, or to bioconcentration by soil actinomycetes and fungi.     

Evaluation of flow injection analysis method with spectrophotometric detection for the determination of atrazine in soil extracts

A method for determining atrazine in soil extracts was evaluated by flow injection analysis with spectrophotometric detection. The method is based on the reaction of atrazine with pyridine in an acid medium followed by the reaction with NaOH and sulfanilic acid. Several analytical conditions were previously studied and optimized. Under the best conditions of analysis, the limits of detection and quantification were 0.15 and 0.45 mg L^?1, respectively, for a linear response between 0.50 and 2.50 mg L^?1, and a sampling throughput of 21 determinations per hour. Using the standard addition method, the maximum relative standard deviation of 17% and recovery values between 80 and 100% were observed for three extracts from soil samples with different composition. The proposed method is simple, low-cost and easy to use, and can be employed for studies involving atrazine in soil samples or for screening of atrazine in soils.     

Comparison of two sample preparation methods for analysis of organochlorine pesticides residues in fish muscle

The aim of this study was to compare recoveries of organochlorine pesticides (heptachlor, α-HCH, β-HCH, γ-HCH, op'-DDD, pp'-DDD, pp'-DDE, op'-DDT, pp'-DDT) from fish muscle dried by two alternative methods: (i) grinding with anhydrous sodium sulphate and (ii) freeze drying. Pesticide residues content was determined by gas chromatography-mass spectrometry (GS-MS) method. For four pesticides (γ-HCH, α-HCH, heptachlor and pp;-DDD) in four of five fish species, higher recoveries were obtained from the freeze-dried samples. For five remaining pesticides, correlations between fish species and drying method were not found. The results of this study do not clearly indicate which drying method caused lower losses of analytes. Recoveries from the freeze-dried samples ranged from 69.9 to 117.6 %, while recoveries from the samples ground with sodium sulphate varied from 64.4 to 126.7 %. Either of the methods gave satisfactory recoveries and they both can be used interchangeably.     

Comparison of two sample preparation methods for analysis of organochlorine pesticides residues in fish muscle

The aim of this study was to compare recoveries of organochlorine pesticides (heptachlor, α-HCH, β-HCH, γ-HCH, op′-DDD, pp′-DDD, pp′-DDE, op′-DDT, pp′-DDT) from fish muscle dried by two alternative methods: (i) grinding with anhydrous sodium sulphate and (ii) freeze drying. Pesticide residues content was determined by gas chromatography-mass spectrometry (GS-MS) method. For four pesticides (γ-HCH, α-HCH, heptachlor and pp;-DDD) in four of five fish species, higher recoveries were obtained from the freeze-dried samples. For five remaining pesticides, correlations between fish species and drying method were not found. The results of this study do not clearly indicate which drying method caused lower losses of analytes. Recoveries from the freeze-dried samples ranged from 69.9 to 117.6 %, while recoveries from the samples ground with sodium sulphate varied from 64.4 to 126.7 %. Either of the methods gave satisfactory recoveries and they both can be used interchangeably.     

A simple HPLC method for determination of permethrin residues in wine

An isocratic High Performance Liquid Chromatographic (HPLC) method was optimized for 3-phenoxybenzyl (1RS)-cis-trans-3-(2,2-dichlorovinyl)-2,2-dimethyl-cyclopropanecarboxylate (permethrin) residues identification and quantification in wine matrix. Analytical reverse phase (RP) C-18 column was used (25 cm × 4 mm i.d., 5 μ m) with mobile phase consisting of acetonitrile and water in ratio 70 %/30 % (v v^?1), flow-rate 2.0 mL min^?1, UV-detection at 215 nm and controlled oven temperature at 25°C. The peaks of isomers were identified with the retention times as compared to standard cis-/trans- mixture and confirmed with characteristic spectra using photodiode array detector. Under these conditions, permethrin isomers were well separated with resolution 2.8 and no interference with the naturally present wine compounds was observed. The method was validated for linearity, precision, accuracy, limit of detection (LOD) and limit of quantification (LOQ). Linear regression analysis data proved a good linear relationship (correlation coefficients, r², for cis- and trans-isomer are: 0.9995 and 0.9997, respectively) between response of the detector and concentration of permethrin isomers over a wide concentration range for both isomers (0.55 mg L^?1 ?4.40 mg L^?1). Experimental data showed mean recoveries between 93.95% and 96.58% with RSD values in range: 0.89% ?3.69%. The effect of ethanol content in the solvent on permethrin isomers peak areas was also studied and 60% v v^?1 ethanol was found to be optimal for sample preparation. The method was successfully tested on 20 commercial wine samples from the market in which no permethrin was detected. Thus, it was proved that it is suitable for routine permethrin residues analysis. The proposed method is suitable for routine analysis because of the simple sample preparation, acceptable run-time, low cost and its applicability with conventional instruments.     

Enzyme-immunoassay techniques for the detection of atrazine in water samples: Evaluation of a commercial tube based assay

Environmental immunoassays can help lower the operating costs and improve the effectiveness of residue laboratories. The present study assesses the ability of a commercially available enzyme immunoassay (EIA) to detect triazine herbicides in water. The tube based EIA could detect atrazine in lake and river water with detection limits of 62 pg/mL and 180 pg/mL respectively. The assay's ability to quantify atrazine in a set of 124 water samples taken from many parts of Canada was compared with a reference method that used gas chromatographic separation combined with a nitrogen phosphorous detector (GC-NPD) (R=0.919). A 71 % reduction in analytical load was achieved at a threshold concentration of 1 ng/mL. There were 2.4 % false negative and 0.8 % false positive results associated with that load reduction. The variability of the assay control parameters was generally within two standard deviations of the mean response for 65 assays. The EIA for atrazine is recommended for use as a screening technique and as an inexpensive way to monitor triazine levels in waters that are known to be contaminated with those herbicides.     

Molecularly imprinted polymer for analysis of trace atrazine herbicide in water

A molecularly imprinted polymer (MIP) for atrazine was synthesized by non-covalent method. The binding capacity of MIP was 1.00 mg g^{? 1} polymer. The selectivity and recovery were investigated with various pesticides which are mostly, found in the environment, for both similar and different chemical structure of atrazine. The competitive recognition between atrazine and structurally similar compounds was evaluated and it was found that the system provided highest recovery and selectivity for atrazine while low recovery and selectivity were obtained for the other compounds. The highest recovery was obtained from MIP compared with non-imprinted polymer (NIP), a commercial C₁₈ and a granular activated carbon (GAC) sorbent. The method provided high recoveries ranged from 94 to 99% at two spiked levels with relative standard deviations less than 2%. The lower detection limit of the method was 80 ng L^{? 1}. This method was successfully applied for analysis of environmental water samples.     

Development of indirect competitive ELISA using egg yolk-derived immunoglobulin (IgY) for the detection of Gentamicin residues

Gentamicin (Gent) is an aminoglycoside antibiotic being used in livestock sector. Gent residues could cause some genetic disorders by nonsense mutations. This study aimed to develop IgY-based ELISA for the detection of Gent in animal products. Gent was conjugated with Bovine serum albumin (BSA) by carbodiimide method for further immunization in the laying chickens. PEG-6000 extraction method was employed to extract IgY from the egg yolk. The titer of anti-Gent-IgY attained the peak of 1:256,000 after the 5^th booster immunization. Checkerboard titration confirmed that, anti-Gent IgY in 1:2,000 dilution could give an Optical Density (OD) 1.0 at 2 µg mL^?1 of Gent-OVA coating concentration. IgY-based indirect competitive ELISA (Ic-ELISA) showed that, the IC₅₀ value of anti-Gent IgY was 2.69 ng mL^?1 and regression curve equation was y = ?16.27x + 56.97 (R² = 0.95, n = 3), confirming that, the detection limit (LOD, IC₁₀ value) was 0.01 ng mL^?1. Recoveries from fresh milk, pork and chicken samples were ranged from 69.82% to 94.32%, with relative standard deviation lower than 10.88%. Our results suggested that generated anti-Gent IgY antibodies can be used in routine screening analysis of Gent residues in food samples.     

Determination of endosulfan residues in eggplant (Solanum melongena) by ELISA

Eggplant samples were analyzed for endosulfan residues using ELISA, a technique recognized as a promising tool for screening environmental contaminants. Calibration curve for endosulfan was standardized using kits developed by CFTRI Mysore. Farm gate samples of eggplant from 12 different locations were analyzed. The matrix effect was removed by charcoal clean-up. The results were compared with gas chromatographic (GC) analysis. The residues in different samples were in the range of 5-226 ppb. Correlation coefficient between the two methods was found to be 0.98.     

Comparison of teleradiometric and sensitometric techniques for visibility measurements

Visibility measurements of power plant and smelter plumes were conducted as part of the 1981 VISTTA field programs by means of sensitometry of color photographic slides and teleradiometry. The results obtained for 10 sets of measurements with these two techniques at three wavelengths (450, 550 and 630 nm) were compared and showed good agreement for plume/sky radiance ratios, with correlation coefficients on the order of 0.9 and average absolute differences of 2–4 per cent. The uncertainty in the plume/sky radiance ratio is about 4 per cent for sensitometry. Although this value is slightly higher than the uncertainty of 2 per cent previously reported for teleradiometry (Bergstrom et al., 1982), sensitometry offers the advantage of an instantaneous measurement. In contrast, a manual teleradiometer scan takes on the order of 15 min, and plume visual effects can show large variations in this short time period.     

Comparison of analytical techniques for the determination of aldehydes in test chambers

The level of carbonyl compounds in indoor air is crucial due to possible health effects and the high prevalence of their potential sources. Therefore, selecting a convenient and rapid analytical technique for the reliable detection of carbonyl compound concentrations is important. The acetyl acetone (acac) method is a widely used standard procedure for detecting gaseous formaldehyde. For measuring formaldehyde along with other carbonyl compounds, the DNPH-method is commonly applied. The recommended procedure for measuring volatile organic compounds (VOCs) is sampling on Tenax TA, followed by thermal desorption and GC/MS analysis. In this study, different analytical techniques for the quantification of formaldehyde, pentanal, and hexanal are critically compared. It was found that the acac- and DNPH-method are in very good agreement for formaldehyde. In contrast, the DNPH-method significantly underestimates indoor air concentrations of the higher aldehydes in comparison to sampling on Tenax TA, although both methods are strongly correlated. The reported results are part of the EURIMA-WKI study on levels of indoor air pollutants resulting from construction, building materials and interior decoration.     

Comparison of lead residues among avian bones

To determine if significant differences exist in lead (Pb) accumulation in different bones, especially those most often used for bone-Pb studies in wildlife, we compared Pb concentrations in radius, ulna, humerus, femur, and tibia of Common Eider (Somateria mollissima); and radius/ulna (combined), femur, and tibia of American Woodcock (Scolopax minor). There were no significant differences in bone-Pb concentrations among woodcock bones over a wide range of Pb concentrations (3-311 microg/g). In eider, where bone-Pb concentrations were low (<10 microg/g), leg bones had significantly higher Pb concentrations (approximately 30-40%) than wing bones from the same individuals. The variation among individual birds was greater than the variation among different bones within a bird. Based on our findings, we conclude that one type of bone may be substituted for another in bone-Pb studies although the same bone type should be analyzed for all birds within a study, whenever possible.     

A method for the analysis of organophosphorus pesticide residues in Mexican axolotl

A method based on matrix solid-phase dispersion (MSPD) was developed for quantitative extraction of three organophosphorus pesticides (OPPs) from the Mexican axolotl, Ambystoma mexicanum. The determination was carried out using high- performance liquid chromatography (HPLC) with diode array spectrophotometric UV detection (DAD). The MSPD extraction with octadecylsilyl (C18) sorbent combined with a silica gel clean-up and acetonitrile elution was optimised for chlorpyrifos, fenthion and methyl parathion. The method was validated, yielding recovery values higher than 90%. The precision, expressed as the relative standard deviation (RSD), was less than or equal to 6% in muscle samples at spiking levels of 10 and 5 ppm. Linearity was studied from 15 to 60 ppm for chlorpyrifos and fenthion, and from 7.5 to 30 ppm for methyl parathion. The limits of detection (LODs) were found to be less than or equal to 0.5 ppm_.This method was applied to the analysis of samples from a chlorpyrifos-exposed axolotl, demonstrating its use as an analytical tool for toxicological studies.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Comparative efficacy of mitigation techniques for the detoxification of Prunus persica (L.) from selected pesticide residues

Environmental Science and Pollution Research - Fruits are the valuable and important components of human diet. Among them, Prunus persica is a rich source of different minerals and dietary fibers....