TiO2-xNx光催化氧化苯甲酸的研究

采用悬浮态光催化反应体系,以氙灯为光源,自制纳米TiO2-xNx为催化剂,考察了苯甲酸光催化氧化过程中TiO2-xNx质量浓度、反应体系初始pH和苯甲酸初始质量浓度对苯甲酸溶液中TOC去除率的影响。实验结果表明：最佳催化剂质量浓度为0．30g／L;TiO2-xNx的等电点为pH=5．3,在酸性条件下（pH=2．0）更有利于苯甲酸在催化剂表面的吸附,以及光生电子与O2反应生成·OH的进行;随苯甲酸初始质量浓度增加,TOC去除率降低,反应速率也相应地降低。TiO2-xNx比P25型TiO2表现出更强的浓度适应能力。     

催化超临界水氧化法去除焦化废水中的氨氮

采用催化超临界水氧化技术处理焦化废水.实验结果表明:升高反应温度、增加反应压力、延长反应时间可提高废水中氨氮去除率;在反应时间为60 s、反应压力为30 MPa、反应温度为460℃的最佳实验条件下,未加入催化剂时的氨氮去除率为53.7％,加入催化剂后,氨氮去除率大幅提高,以MnO2为催化剂时氨氮去除率为86.9％,以CuSO4为催化剂时氨氮去除率为92.4％.     

工业废水中苯系物的去除方法

本发明提供了一种工业废水中苯系物的去除方法，步骤包括：（1）选择新鲜翠绿、生长良好的刚毛藻附着在网状载体上，置于自来水中驯化培养1—2d；（2）将驯化后的载有刚毛藻的网状载体置于深度为20～40cm的工业废水水面上，处理时间2～6h。驯化、处理条件：光强2500—3500lx，相对湿度35％～50％，温度15—25℃，光暗周期比为12：12。用刚毛藻处理污水中的苯和甲苯，一次去除率可达62．7％～78．6％，且运行设备简单，投资少，     

H2O2协同TiO2光催化处理模拟苯胺废水

采用TiO2光催化处理模拟苯胺废水.实验结果表明,最佳反应条件为:初始苯胺质量浓度10 mg/L,纳米TiO2加入量100 mg/L,光催化反应时间60 min,废水pH 7.5.加入20 mg/L的H2O2协同TiO2光催化处理苯胺废水,光催化反应24 min后,苯胺去除率达99％.H2O2协同TiO2光催化降解苯胺过程符合二级动力学方程.     

锐钛矿-金红石混合晶型TiO2降解气相苯

用溶胶-凝胶法并通过控制煅烧温度合成不同晶相比的混合晶型纳米TiO_2,在紫外光光照下降解气相苯。考察了苯初始质量浓度、紫外灯光照强度和催化剂加入量对苯去除率的影响;探究了光催化降解气相苯的动力学特征。结果表明:450℃煅烧制备的催化剂降解苯效率最高,此催化剂金红石相质量分数为6.30%;在苯初始质量浓度为74.39 mg/m~3、催化剂加入量为7 g、光照强度为2.18 klux的最佳条件下反应84 min,苯去除率达99.73%;光催化降解率与光照强度之间符合0.5级动力学特征;当催化剂加入量为3 g时,单位时间单位质量催化剂降解苯的质量最多;苯的光催化降解反应均符合一级动力学方程。     

络合-电沉积法制备TiO_2纳米管负载Ag光催化剂

采用柠檬酸钠作为络合剂,通过络合-电沉积法制备了TiO2纳米管负载Ag光催化剂(Ag/TiO2NTs),通过FE-SEM和XRD等手段对Ag/TiO2NTs进行了表征。以偶氮染料甲基橙(MO)为目标降解物,考察了不同制备条件对Ag/TiO2NTs光催化性能的影响。表征结果显示,柠檬酸钠可以有效调控Ag+的电化学还原过程,实现Ag纳米颗粒在TiO2纳米管表面的均匀负载。实验结果表明:以在n(柠檬酸钠)∶n(Ag NO3)=1、电流密度为0.4 m A/cm2、煅烧温度为500℃的条件下制得的Ag/TiO2NTs作为光催化剂(Ag负载量为1.97%(x)),处理初始质量浓度为20 mg/L、初始溶液p H为9的MO溶液,光催化反应120 min后MO去除率为86.53%;经过6次的重复使用,Ag/TiO2NTs催化剂光催化降解MO的去除率基本稳定在80%以上。     

UV/O3催化氧化法处理发酵废水中难降解有机物的研究

以UV／O3氧化法降解生化处理后的发酵有机废水为处理体系，研究了活性炭、二氧化钛对废水中难降解有机物的UV／O3催化活性，考察了催化剂用量以及活性炭和二氧化钛的协同催化效果。结果表明，活性炭与二氧化钛均能明显加快反应速率，提高CODcr去除率并缩短反应时间，且活性炭与TiO2协同催化效果更好，二者以最佳比例(6：1)作用，反应4h后，废水的CODcr去除率达到85％以上。     

电化学法处理高盐苯酚废水的研究

对在氯盐电解质中用电化学方法处理含酚废水进行了研究，着重探讨了盐的种类与浓度、反应温度与溶液：pH、电流密度、苯酚初始浓度及阴阳极转换频率对苯酚去除率的影响。在Na2SO4的浓度为0．2mol／L，NaCl的浓度为0．1mol／L、苯酚初始质量浓度为200mg／L、电流密度为0．04A／cm^2、温度为35℃、pH为12．5、阴阳极转换频率为5min/次及反应时间为200min的条件下，苯酚的去除率为99．5％，COD去除率为5％，CIO^-把苯酚氧化成了其他有机化合物。     

超声波与多相类Fenton氧化联用技术降解硝基苯

以FeOOH作为催化剂,采用超声波与多相类Fenton氧化联用技术降解硝基苯。研究结果表明:在超声波功率为150 W、频率为40 kHz、溶液pH为3、初始硝基苯质量浓度为6.16 mg/L、H2O2加入量为17.01 mg/L、FeOOH加入量为100 mg/L时,反应120 min后硝基苯去除率达88.06%;加入·OH捕获剂叔丁醇后,FeOOH和超声波-FeOOH反应体系的硝基苯去除率均显著下降;随着反应时间的延长,FeOOH和超声波-FeOOH反应体系的铁溶出量均逐渐增大,但在整个反应过程中,总铁和Fe2+质量浓度均很小。     

纳米TiO2薄膜光催化降解废水中的苯胺

以钛酸丁酯为原料、无水乙醇为溶剂、硝酸为抑制剂,采用溶胶-凝胶法于500℃制备了3～6层的锐钛矿型纳米TiO2薄膜.以TiO2薄膜为催化剂,紫外灯为光源,通过正交实验确定了光催化降解废水中苯胺的最佳操作条件.实验结果表明:当初始苯胺质量浓度为10 mg/L、光照时间为7h、紫外灯功率为20 W、初始废水pH为8、TiO2薄膜层数为6时,苯胺去除率达到80.00％.     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.