The Solling roof revisited--slow recovery from acidification observed and modeled despite a decade of "clean-rain" treatment

Soil chemistry under the Solling clean-rain roof was simulated using the dynamic multi-layer soil chemistry model SAFE, including sulfate adsorption. Soil was sampled in order to parameterize the pH and sulfate concentration dependent sulfate adsorption isotherm used in SAFE. Modeled soil solution chemistry was compared to the 14 year long time-series of monthly measurements of soil solution data at 10 and 100cm depth. The deposition of N and S under the roof has been reduced by 68% and 53%, respectively, compared to the surrounding area. Despite this the soil solution concentrations of sulfate are still high (a median of 420mumol(c)/L at 100cm depth between 2000 and 2002) and the soil base saturation low (approximately 3% in the whole profile in 1998). Sulfate adsorption is an important process in Solling. The soil capacity to adsorb sulfate is large, the modeled adsorbed pool in 2003 down to 100cm was 1030kg S/ha, and the measured sulfate concentration is high, due to release of adsorbed sulfate. The addition of sulfate adsorption improved the modeled sulfate dynamics although the model still slightly underestimated the sulfate concentration at 100cm. Model predictions show no recovery, based on the criteria of Bc/Al ratio above 1 in the rooting zone, before the year 2050, independent of future deposition cuts.     

Modeling the competitive effect of phosphate, sulfate, silicate, and tungstate anions on the adsorption of molybdate onto goethite

The mobility of Mo in soils and sediments depends on several factors including soil mineralogy and the presence of other oxyanions that compete with Mo for the adsorbent's retention sites. Batch experiments addressing Mo adsorption onto goethite were conducted with phosphate, sulfate, silicate, and tungstate as competing anions in order to produce competitive two anions adsorption envelopes, as well as competitive two anions adsorption isotherms. Tungstate and phosphate appear to be the strongest competitors of Mo for the adsorption sites of goethite, whereas little competitive effects were observed in the case of silicate and sulfate. Mo adsorption isotherm from a phosphate solution was similar to the one from a tungstate solution. The charge distribution multi-site complexation (CD-MUSIC) model was used to predict competitive adsorption between MoO(4)(2-) and other anions (i.e., phosphate, sulfate, silicate and tungstate) using model parameters obtained from the fitting of single ion adsorption envelopes. CD-MUSIC results strongly agree with the experimental adsorption envelopes of molybdate over the pH range from 3.5 to 10. Furthermore, CD-MUSIC prediction of the molybdate adsorption isotherm show a satisfactory fit of the experimental results. Modeling results suggest that the diprotonated monodentate complexes, FeOW(OH)(5)(-0.5) and FeOMo(OH)(5)(-0.5), were respectively the dominant complexes of adsorbed W and Mo on goethite 110 faces at low pH. The model suggests that Mo and W are retained mainly by the formation of monodentate complexes on the goethite surface. Our results indicate that surface complexation modeling may have applications in predicting competitive adsorption in more complex systems containing multiple competing ions.     

SDS改性沸石吸附结晶紫简

以表面活性剂十二烷基硫酸钠（SDS）对沸石进行改性,改性后的沸石对结晶紫溶液进行吸附,以紫外可见分光光度计分析最佳吸附条件。实验结果表明,在30℃,SDS改性沸石投入量为0.25 g;吸附平衡时间为1 h;pH为8的条件下,对含50 mg/L结晶紫染料的去除率可达到92.6%,吸附量达到4.63 mg/g。SDS改性沸石吸附结晶紫的等温吸附曲线与Henry型和Freundlich型均拟合较好。热力学参数计算结果表明,吸附符合自发吸热过程。     

SDS改性沸石吸附结晶紫

以表面活性剂十二烷基硫酸钠（SDS）对沸石进行改性,改性后的沸石对结晶紫溶液进行吸附,以紫外可见分光光度计分析最佳吸附条件。实验结果表明,在30℃,SDS改性沸石投入量为0．25g;吸附平衡时间为1h;pH为8的条件下,对含50mg／L结晶紫染料的去除率可达到92．6％,吸附量达到4．63mg／g。SDS改性沸石吸附结晶紫的等温吸附曲线与Henry型和Freundlich型均拟合较好。热力学参数计算结果表明,吸附符合自发吸热过程。     

Zn / Al 双金属氧化物对水中硫酸根离子的吸附性能简

研究了用Zn/Al水滑石制得的Zn/Al双金属氧化物（Zn/Al-300）吸附剂对水中硫酸根离子的吸附,考查了吸附剂投加量、初始pH等因素对硫酸根离子吸附的影响。结果表明,Zn/Al-300对水中硫酸根离子的吸附符合Langmuir吸附等温方程,理论最大吸附量为62.5 mg/g。运用动力学方程进行拟合,吸附过程符合准二级动力学方程;溶液的pH影响吸附剂对硫酸根的吸附,在pH=5.5时硫酸根的去除率最大;X射线衍射结果显示,水滑石经过焙烧后丧失了原有的构形,并在吸附硫酸根离子后重新恢复水滑石的部分层状结构。吸附机制主要为Zn/Al-300从溶液中获取阴离子以重建水滑石的晶体结构,即“记忆效应”。对吸附后的双金属氧化循环应用4此后,吸附容量几乎不变,说明双金属氧化物具有可循环型。通过将Zn/Al-300与其他几种吸附剂的经济性分析,表明此吸附剂在使用过程中具有一定优势。     

Fluoride removal performance of a novel Fe-Al-Ce trimetal oxide adsorbent

A trimetal oxide was developed as a fluoride adsorbent by coprecipitation of Fe(II), Al(III) and Ce(IV) salt solutions with a molar ratio of 1:4:1 under alkaline condition. The material retained amorphous structure and maintained relatively stable fluoride adsorption performance at calcination temperatures lower than 600 degrees C. The optimum pH range for fluoride adsorption was 6.0-6.5 and the adsorbent also showed high defluoridation ability around pH 5.5-7.0, which is preferable for actual application. A high fluoride adsorption capacity of 178 mg g(-1) was acquired under an equilibrium fluoride concentration of 84.5 mg l(-1), adsorbent dose of 150 mg l(-1) and pH 7.0. The adsorption isotherm could be better described by the two-site Langmuir model than the one-site model, suggesting the existence of two types of active sites on the adsorbent surface. Coexistence of high concentrations of phosphate or arsenate only led to partial inhibition of fluoride adsorption, which further suggests the existence of heterogeneous adsorption sites. Sulfate and chloride did not affect fluoride adsorption, and nitrate influenced it only when the concentration of NO(3)(-)-N exceeded 50 mg l(-1). A high desorption efficiency of 97% was achieved by treating fluoride loaded Fe-Al-Ce oxide with NaOH solution at pH 12.2. A column experiment using the adsorbent fabricated into 1mm pellets was performed at an initial fluoride concentration of 5.5 mg l(-1), space velocity of 5h(-1) and pH of 5.8, and 2240 bed volumes were treated with the effluent fluoride under 1.0 mg l(-1).     

Inhibition of rainbow trout acetylcholinesterase by aqueous and suspended particle-associated organophosphorous insecticides

Cadmium (Cd) adsorption on 14 non-calcareous New Jersey soils was investigated with a batch method. Both adsorption edge and isotherm experiments were conducted covering a wide range of soil composition, e.g. soil organic carbon (SOC) concentration ranging from 0.18% to 7.15%, and varying Cd concentrations and solution pH. The SOC and solution pH were the most important parameters controlling Cd partition equilibrium between soils and solutions in our experimental conditions. The Windermere humic aqueous model (WHAM) was used to calculate Cd adsorption on soils. The effect of solution chemistry (various pH and Cd concentrations) on Cd adsorption can be well accounted for by WHAM. For different soil compositions, SOC concentration is the most important parameter for Cd binding. Only a fraction of SOC, the so-called active organic carbon (AOC), is responsible for Cd binding. We found a linear relationship between SOC and AOC based on the adsorption edge data. The linear relationship was validated by the independent data sets: adsorption isotherm data, which presumably can be used to predict Cd partition equilibrium across a wide range of soil compositions. The modeling approach presented in this study helps to quantitatively predict Cd behavior in the environment.     

改性松针对水体中铅(II)的吸附

探讨了改性松针(GXLsp)作为吸附剂对水体中铅离子的吸附性能,考察了吸附时间、溶液pH值、吸附剂用量、盐离子浓度、Pb(II)初始浓度及温度对改性松针吸附Pb(II)的影响。利用Langmuir和Freundlich等温线模型对实验数据进行非线性拟合分析,结果表明,Freundlich等温线模型能很好地描述松针对Pb(II)的吸附过程。热力学参数表明吸附是一个自发的吸热过程。改性松针对铅的吸附行为符合拟二级动力学方程,表明吸附过程是以化学吸附为主。在293K时松针对Pb(II)的饱和吸附量为318.3 mg/g,因此,GXLsp可作为一种高效低值生物质吸附剂以去除水体中重金属Pb(II)的污染。     

腐熟污泥对废水中Cd(Ⅱ)与Zn(Ⅱ)的吸附性能研究

利用腐熟污泥作为一种重金属吸附剂,考察其对水中重金属锌和镉的吸附过程.实验数据的拟合采用了Pseudo-first Order-和Pseudo-second Order 2种动力学模型以及Langmuir和Freundlich 2种吸附等温线模型;拟合结果表明,腐熟污泥对锌与镉的吸附过程符合Pseudo-second ...     

Characterization of Cr ion exchange with hydrotalcite

Experiments were performed to characterize the removal of chromium from water with uncalcined hydrotalcite, a clay mineral ion exchange media. The process was characterized as a function of pH, temperature, contact time, and both Cr and hydrotalcite concentrations. A Freundlich isotherm, used to describe adsorption equilibria, was used as a model and Freundlich constants were determined. The kinetics of the ion exchange reaction were also modeled using a pseudo-first order reaction rate. Finally, an equilibrium stage process was modeled with sequential batch separations to determine if hydrotalcite ion exchange could reduce aqueous Cr levels to below the EPA limit of 0.1mgl(-1). It was shown that the process is highly pH dependent, only yielding significant removals at pH levels between 2.0 and 2.1. While hydrotalcite concentration, Cr concentration, and time did effect the ion exchange, temperature was not found to be a factor. Under optimal conditions, maximum removals of greater than 95% were achieved. Finally, sequential batch tests performed on initial Cr solutions ranging from 5mgl(-1) to 40mgl(-1), demonstrated that the water could be purified to a level that was not statistically different than the EPA limit, thus demonstrating the applicability of hydrotalcite ion exchange.     

Phosphate removal from wastewater using aluminium oxide as adsorbent

The development and manufacture of an adsorbent to remove phosphate for the prevention of eutrophication in lakes is very important. The use of aluminium oxide (alumina) as an organic adsorbent to remove phosphate from wastewater has been investigated. The characteristics of this absorption process were investigated to determine the important parameters, such as the pH and the aluminium ion concentration. Moreover, chemical treatment methods to enhance the adsorption capacity of alumina were tested. Dynamic studies and equilibrium adsorption isotherm studies were conducted to determine the adsorption capacity and efficiency. The experimental results indicate that it is necessary to increase the temperature above 500°C in order to obtain a high-capacity adsorbent, and alumina treated with acid or calcium or magnesium has a larger adsorption capacity for phosphate than untreated adsorbent. Moreover, the adsorption of phosphate was enhanced at a lower pH and a higher aluminium ion concentration, and a simple Freundlich isotherm could express the equilibrium adsorption isotherm, and the intragranular diffusion controlling model was used to test the dynamic studies. These findings have important implications for the application and development of aluminium oxide as a prospective adsorbent.     

Arsenic(III) removal by adsorption on sawdust carbon

Studies on the removal of As(III) by adsorption on sawdust and sawdust carbon have been carried out at room temperature (25 ± 1°C). The adsorption isotherm of As(III) on sawdust carbon was obtained in a batch reactor. The process of uptake follows the first-order adsorption rate expression and obeys the Langmuir and Freundlich model of adsorption. The mass transfer coefficients as a function of initial sorbate concentration have been determined. Parameters such as pH and absorbent dose were studied. Maximum adsorption capacity was observed at pH 7.0.     

Adsorption characteristics of 2,4-dichlorophenoxyacetic acid (2,4-D) from aqueous solution on powdered activated carbon

The removal of 2,4-dichlorophenoxyacetic acid (2,4-D), one of the most commonly used phenoxy acid herbicides, from aqueous solution was studied by using acid-washed powdered activated carbon (PAC) as an adsorbent in a batch system. Adsorption equilibrium, kinetics, and thermodynamics were investigated as a function of initial pH, temperature, and initial 2,4-D concentration. Powdered activated carbon exhibited the highest 2,4-D uptake capacity of 333.3 mg g(-1) at 25 degrees C and an initial pH value of 2.0. Freundlich, Langmuir, and Redlich-Peterson isotherm models were used to express the equilibrium data of 2,4-D depending on temperature. Equilibrium data fitted very well to the Freundlich equilibrium model in the studied concentration range of 2,4-D at all the temperatures studied. Three simplified models including pseudo-first-order, pseudo-second-order, and saturation-type kinetic models were used to test the adsorption kinetics. It was shown that the adsorption of 2,4-D on PAC at 25, 35, and 45 degrees C could be best fitted by the saturation-type kinetic model with film and intraparticle diffusions being the essential rate-controlling steps. The activation energy of adsorption (EA) was determined as--1.69 kJ mole(-1). Using the thermodynamic equilibrium coefficients obtained at different temperatures, the thermodynamic constants of adsorption (deltaG degrees, deltaH degrees, and deltaS degrees) were also evaluated.     

Modeling interactions of Hg(II) and bauxitic soils

The adsorptive interactions of Hg(II) with gibbsite-rich soils (hereafter SOIL-g) were modeled by 1-pK surface complexation theory using charge distribution multi-site ion competition model (CD MUSIC) incorporating basic Stern layer model (BSM) to account for electrostatic effects. The model calibrations were performed for the experimental data of synthetic gibbsite-Hg(II) adsorption. When [NaNO(3)] > or = 0.01M, the Hg(II) adsorption density values, of gibbsite, Gamma(Hg(II)), showed a negligible variation with ionic strength. However, Gamma(Hg(II)) values show a marked variation with the [Cl(-)]. When [Cl(-)] > or = 0.01M, the Gamma(Hg(II)) values showed a significant reduction with the pH. The Hg(II) adsorption behavior in NaNO(3) was modeled assuming homogeneous solid surface. The introduction of high affinity sites, i.e., >Al(s)OH at a low concentration (typically about 0.045 sites nm(-2)) is required to model Hg(II) adsorption in NaCl. According to IR spectroscopic data, the bauxitic soil (SOIL-g) is characterized by gibbsite and bayerite. These mineral phases were not treated discretely in modeling of Hg(II) and soil interactions. The CD MUSIC/BSM model combination can be used to model Hg(II) adsorption on bauxitic soil. The role of organic matter seems to play a role on Hg(II) binding when pH>8. The Hg(II) adsorption in the presence of excess Cl(-) ions required the selection of high affinity sites in modeling.     

硫酸铝渣去除水中磷研究

分别以蒸馏水和太湖水为例,研究了硫酸铝渣去除水中磷的能力,并分析了其对水体Al3+、SO24-以及pH的影响.结果表明:(1)除太湖水pH为9.0、10.0两种条件外,随着磷平衡浓度的增加,硫酸铝渣除磷量趋于某一定值,其规律符合Langmuir吸附等温式;太湖水pH为9.0、10.0两种条件下,硫酸铝渣除磷量符合Fre...     

Crystalline hydrous ferric oxide: an adsorbent for chromium(VI)-contaminated industrial wastewater treatment.

Synthetic crystalline hydrous ferric oxide (CHFO) (particle size 0.14 to 0.29 mm) has been used systematically for adsorptive chromium(VI) removal from contaminated water. Batch experiments were performed as a function of pH, contact time, solute concentration, and regeneration of adsorbents. Column experiments were performed for breakthrough points in the presence and absence of other ions and treatment of industrial effluent. The optimum pH range was 2.0 to 4.0. The adsorption kinetic data could be described well by both second-order and pseudo-first-order models. The isotherm adsorption data at 30 +/- 2 degrees C obeyed the Langmuir model best. The monolayer adsorption capacity was 35.7 mg/g. Chromium(VI)-rich CHFO could be regenerated up to 89 +/- 1% with 2.0 M sodium hydroxide. Regenerated column reuse showed a decrease (10 to 12%) in breakthrough capacity. Finally, the CHFO- (dried at 300 degrees C) packed column was used for the recovery (98.5 +/- 1.0%) of chromium(VI) from contaminated industrial waste effluent of Hindustan Motor Limited (Hooghly, West Bengal, India).     

Activated carbon from industrial solid waste as an adsorbent for the removal of Rhodamine-B from aqueous solution: kinetic and equilibrium studies

The activated carbon was prepared using industrial solid waste called sago waste and physico-chemical properties of carbon were carried out to explore adsorption process. The effectiveness of carbon prepared from sago waste in adsorbing Rhodamine-B from aqueous solution has been studied as a function of agitation time, adsorbent dosage, initial dye concentration, pH and desorption. Adsorption equilibrium studies were carried out in order to optimize the experimental conditions. The adsorption of Rhodamine-B onto carbon followed second order kinetic model. Adsorption data were modeled using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity Q0 was 16.12 mg g(-1) at initial pH 5.7 for the particle size 125-250 microm. The equilibrium time was found to be 150 min for 10, 20 mg l(-1) and 210 min for 30, 40 mg l(-1) dye concentrations, respectively. A maximum removal of 91% was obtained at natural pH 5.7 for an adsorbent dose of 100mg/50 ml of 10 mg l(-1) dye concentration and 100% removal was obtained when the pH was increased to 7 for an adsorbent dose of 275 mg/50 ml of 20 mg l(-1) dye concentration. Desorption studies were carried out in water medium by varying the pH from 2 to 10. Desorption studies were performed with dilute HCl and show that ion exchange is predominant dye adsorption mechanism. This adsorbent was found to be both effective and economically viable.     

Use of carbonised beet pulp carbon for removal of Remazol Turquoise Blue-G 133 from aqueous solution

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g^?1at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.     

Removal of congo red from aqueous solution by bagasse fly ash and activated carbon: kinetic study and equilibrium isotherm analyses

Present investigation deals with the utilisation of bagasse fly ash (BFA) (generated as a waste material from bagasse fired boilers) and the use of activated carbons-commercial grade (ACC) and laboratory grade (ACL), as adsorbents for the removal of congo red (CR) from aqueous solutions. Batch studies were conducted to evaluate the adsorption capacity of BFA, ACC and ACL and the effects of initial pH (pH(0)), contact time and initial dye concentration on adsorption. The pH(0) of the dye solution strongly affected the chemistry of both the dye molecules and BFA in an aqueous solution. The effective pH(0) was 7.0 for adsorption on BFA. Kinetic studies showed that the adsorption of CR on all the adsorbents was a gradual process. Equilibrium reached in about 4h contact time. Optimum BFA, ACC and ACL dosages were found to be 1, 20 and 2 g l(-1), respectively. CR uptake by the adsorbents followed pseudo-second-order kinetics. Equilibrium isotherms for the adsorption of CR on BFA, ACC and ACL were analysed by the Freundlich, Langmuir, Redlich-Peterson, and Temkin isotherm equations. Error analysis showed that the R-P isotherm best-fits the CR adsorption isotherm data on all adsorbents. The Freundlich isotherm also shows comparable fit. Thermodynamics showed that the adsorption of CR on BFA was most favourable in comparison to activated carbons.     

凹凸棒土对腐殖酸的低温吸附性能研究

首次研究凹凸棒土对饮用水中腐殖酸的低温吸附性能,考察5℃条件下,吸附时间与腐殖酸初始浓度、吸附剂投加量、pH对凹凸棒土吸附腐殖酸的影响,确定吸附剂的吸附等温线、吸附动力学和热力学等相关理论参数,研究凹凸棒土对腐殖酸的吸附性能与机理。结果表明,江苏盱眙凹凸棒土在温度5℃、pH=4、水中腐殖酸初始浓度为5 mg/L,投加量为15 g/L的条件下,吸附180 min后对腐殖酸的去除率可达97.26%。凹凸棒土对腐殖酸的吸附符合二级吸附动力学方程与Freundlich吸附等温式,吸附过程由孔隙内扩散过程控制,吸附为自发的吸热过程,包括物理吸附与化学吸附。根据Fre-undlich吸附等温式拟合计算,5℃、pH=7时理论最大吸附量为9 mg/g,说明凹凸棒土对于低温饮用水中腐殖酸具有良好的吸附效果。