表面活性剂在北京碱性土壤中的吸附行为研究

通过静态吸附实验,研究了北京碱性土壤对阴离子表面活性剂SDS、阳离子表面活性剂CTAB和非离子表面活性剂Tween80的吸附行为,考察了温度对表面活性剂吸附的影响.结果表明:7种不同土样对SDS、CTAB和Tween80的吸附等温线均较好地符合Langmuir吸附模式,其吸附能力的大小顺序为2号轻壤土》轻粘土》中壤土》砂壤土》5号轻壤土》重壤土》紧砂土,这主要是由于7种土样的pH、有机质含量和机械组成不同的缘故;同一土壤中,CTAB的吸附量》Tween80的吸附量》SDS的吸附量;温度的升高,不利于SDS和CTAB在土壤中的吸附,而有利于Tween80的吸附.     

LAS对土壤中多环芳烃吸附行为的影响

研究了阴离子表面活性剂十二烷基苯磺酸钠(LAS)对PAHs在土壤中吸附行为的影响.结果表明,LAS改变了PAHs在土水体系中的吸附/解吸平衡,吸附态LAS可提高土壤对PAHs的吸附,而溶解态LAS则增加了PAHs的表观溶解度,这2种作用的综合结果改变了PAHs在土水体系中的吸附系数.因此,文中用表观吸附系数来描述PAHs在土壤-水-LAS体系中的综合吸附行为.     

表面活性剂对黄土中石油污染物的解吸影响研究

研究了用表面活性剂去除黄土中柴油类污染物。选用阴离子表面活性剂十二烷基苯磺酸钠和十二烷基硫酸钠 (LAS和SDS)和阳离子表面活性剂十六烷基三甲基溴化铵 (CTAB)对污染的土壤进行解吸实验 ,表明阴离子表面活性剂浓度从 0 .1%增加到 1.0 %时 ,其柴油的去除率可达 2 0 % ,而阳离子表面活性剂去除作用不甚明显。利用摩尔增溶比MSR值求得LAS和SDS的logKm 值为 4.5 5 2和 3 .63 0 ,这和理论的计算值很接近     

LAS对土壤中多环芳烃吸附行为的影响

研究了阴离子表面活性剂十二烷基苯磺酸钠（LAS）对PAHs在士壤中吸附行为的影响。结果表明，LAS改变了PAHs在土水体系中的吸附／解吸平衡，吸附态LAS可提高土壤对PAHs的吸附，而溶解态LAS则增加了PAHs的表观溶解度，这2种作用的综合结果改变了PAHs在土水体系中的吸附系数。凶此，文中用表观吸附系数来描述PAHs在土壤-水-LAS体系中的综合吸附行为。     

表面活性剂对黄土中石油污染物的解吸影响研究

研究了用表面活性剂去除黄土中柴油类污染物。选用阴离子活性剂十二烷基苯磺酸钠和十二烷基硫酸钠（LAS和SDS）和阳离子表面活性剂十六烷基三甲基溴化铵（CTAB）对污染的土壤进行解吸实验，表明阴离子表面活性剂浓度从0.1%增加到1.0%时，其柴油的去除率可达20％，而阳离子表面活性剂去除作用不甚明显。利用摩尔增溶比MSR值求得LAS和SDS的logKm值为4.552和3.630，这和理论的计算值很接近。     

pH和温度对2,2’,4,4’-四溴联苯醚在土壤中吸附和解吸行为的影响研究

研究了pH和温度对2,2’,4,4’-四溴联苯醚(BDE-47)在土壤中的吸附和解吸行为的影响。结果表明,pH和温度都可以影响BDE-47在受试土壤中的吸附和解吸行为。pH升高或降低均会使土壤对BDE-47的吸附能力提高,且在碱性环境中提高的程度更大;酸性或碱性条件下BDE-47在土壤中的解吸滞后性显著增强。温度降低后,土壤对BDE-47的吸附能力提高,5℃时的单点分配系数(Kd,表征土壤对BDE-47的吸附能力)是25℃时的1.03~1.67倍;温度由25℃降低到5℃后,BDE-47在土壤中的解吸滞后性增强。     

汞矿区周边土壤和溪流底泥对汞的吸附解吸特征

为充分认识汞在土壤和底泥中的吸附解吸特征,采取恒温水平振荡法对汞矿区周边未污染土壤和溪流底泥进行了Hg~(2+)的吸附解吸实验并用吸附等温方程和动力学方程对吸附过程进行了拟合对比。结果表明,土壤和底泥对Hg~(2+)的吸附过程类似,在中性条件下,其饱和吸附量分别为1 848.77 mg·kg~(-1)、941.25 mg·kg~(-1)在过酸或者过碱的条件下,均不利于土壤和底泥对Hg(Ⅱ)的吸附;在初始5 min内,土壤和底泥对Hg~(2+)的吸附量分别达到了饱和吸附量的72.64%、62.68%,200 min内基本达到吸附饱和;Hg~(2+)在土壤和底泥中的吸附量越大,其解吸量也越大,土壤对Hg~(2+)的吸附量及量成正比例关系,且Hg~(2+)一旦进入土壤或底泥,则很难再被解吸出来,土壤和底泥的最大解吸率分别为0.92%、1.32%。Langmuir、Freundlich和TemKin 3种曲线均能较好地拟合土壤和底泥二者对Hg~(2+)的等温吸附过程,但Langmuir的拟合度更高,显著水平分别达到了0.997 6,0.995 9;Elovich、双常数方程均能较好地拟合土壤和底泥对Hg~(2+)的吸附动力学过程,Eovich方程更适合拟合土壤对Hg~(2+)的吸附动力学,双常数方程更适合底泥的动力学拟合,显著水平分别达到0.935 0、0.919 9。     

不同利用方式土壤中磷的吸附与解吸特性

研究不同利用方式土壤对磷的吸附解吸特性及其影响因素。采用室内恒温培养法研究了湖南典型土壤(红壤、潮土和紫色土)的不同利用方式(旱地、水田)土壤对P的吸附和解吸过程。土壤对磷的吸附解吸过程是分阶段进行的,用Langmuir方程拟合程度比Freundlich方程高,相关系数均在0.90(P<0.05)以上;从最大吸附量(Qm)、吸附反应常数(K)和最大缓冲容量(MBC)3项吸附参数综合考虑,旱地对P的吸附无论在强度还是容量方面均大于同母质的水田土壤;解吸率随着吸附量的增加而增大,其大小为旱地<水田。Qm与<0.002 mm粘粒及无定形铁含量呈正相关,相关系数分别为0.95和0.94(P<0.05)。不同利用方式土壤P吸附解吸特性差别较大,针对不同土壤应采取不同的磷素管理措施以实现作物增产和保护环境的双重效益。     

甘氨酸-β-环糊精对菲的增溶、解吸行为研究

为改善β-环糊精的水溶性,将β-环糊精和甘氨酸在碱性条件下用环氧氯丙烷连接起来,得到水溶性极好的甘氨酸-β-环糊精,研究了甘氨酸-β-环糊精对菲的增溶、解吸行为,考察了pH、甘氨酸-β-环糊精初始浓度、温度、不同环糊精类型对菲解吸的影响。结果表明,甘氨酸-β-环糊精对菲的增溶效果显著,其初始质量浓度为30 g/L时,对菲的增溶倍数可以达到近30倍;甘氨酸-β-环糊精对菲的解吸随pH的升高而降低;升高甘氨酸-β-环糊精初始浓度和温度有利于菲的解吸;甘氨酸-β-环糊精对菲的解吸好于α-环糊精和β-环糊精,甘氨酸-β-环糊精对菲污染土壤的解吸符合准二级动力学方程。该静态解吸研究可以为菲污染土壤的修复提供基础信息。     

十六烷基三甲基溴化铵对重油在海洋沉积物上吸附的影响

研究了阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)对重油在海洋沉积物上吸附的影响。结果表明,在CTAB初始质量浓度为0～20mg/L时,海洋沉积物对重油的吸附动力学过程符合伪二级吸附动力学方程,伪二级吸附速率常数随CTAB初始浓度增加、温度的升高而增大;吸附等温线符合Freundlich方程。随着CTAB初始浓度和盐度的增加、温度的降低,重油在海洋沉积物上的吸附量增大。标准吸附焓变(ΔH0)、标准吉布斯自由能变(ΔG0)、标准吸附熵变(ΔS0)的计算结果表明,重油在海洋沉积物上的吸附为物理吸附,是一个自发、放热、熵减小的过程。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

有机官能团对改性硅吸附微囊藻毒素的影响

考察了不同有机改性硅对微囊藻毒素LR(mLR)和LA(mLA)的等温吸附行为。结果表明,有机改性硅可有效吸附去除水体中<0.1×10-6(质量分数)的微囊藻毒素,并且吸附去除效果随表面改性官能团中碳原子数量的增加而增加;相同条件下,有机改性硅在微囊藻毒素异构体之间存在着一定的吸附选择性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.