初始pH值对泔脚发酵产氢余物甲烷化的强化研究

以城市生活垃圾厌氧消化污泥为接种物,考察了初始pH值为5、6、7和8时对泔脚发酵产氢余物中温(36℃)批式厌氧消化的影响。结果表明,当初始pH值低于7时,随着初始pH值的增大,产氢余物的产甲烷能力也随之增大;而当初始pH值高于7时,体系的产沼能力却受到了极大的抑制。结合Gompertz模型拟合结果,初始pH值为7为泔脚发酵产氢余物沼气化的最佳初始pH值,其沼气化的延迟时间λ、产甲烷率、生物气中甲烷的最高体积含量分别为:4.02 d,379.28 mL/g VS,82.2%。厌氧消化结束后,除初始pH值为5的以外,厌氧消化余物的pH值在6.8~6.9之间,这为沼气中甲烷的高体积含量(高于常规厌氧消化的最高甲烷体积含量75%)提供了证据。     

磷酸盐缓冲液初始pH值对高含固污泥厌氧消化性能影响

在高含固污泥厌氧反应器中投加浓度为20 mmol·L-1(以P元素计)的磷酸盐缓冲溶液,考察不同pH值的缓冲溶液对污泥厌氧消化效果的影响。结果表明,投加pH为7.0的缓冲溶液后,总甲烷产量达到最大值61.08 L,较对照提高了38.1%,而投加pH为7.5和8.0的缓冲溶液后对产甲烷过程产生了抑制。投加缓冲溶液的各组厌氧消化至45 d,污泥的VS去除率均高于对照组。动力学研究表明,蛋白质和多糖的降解符合一级反应动力学,投加缓冲溶液有利于加速蛋白质的降解,而对多糖的降解无明显影响。     

餐厨垃圾高温厌氧消化

在中试规模下,研究餐厨垃圾高温厌氧消化试验,通过监测餐厨垃圾厌氧消化过程中产气量、气体组成等产气情况和消化液中pH值、SCOD、NH4+-N、VFAs等化学指标含量变化,确定餐厨垃圾厌氧消化的最大有机负荷,并分析餐厨垃圾高温厌氧消化技术的可行性,结果表明,在工程上餐厨垃圾单独进行高温厌氧消化产甲烷具有技术可行性,但难以保证系统长时间安全稳定运行;餐厨垃圾厌氧消化正常运行时最大有机负荷可达2.551 kg VS/(m3.d);当系统有机负荷为2.551 kg VS/(m3.d)时,每天每千克VS最高可产生甲烷量0.622 m3;氨氮对餐厨垃圾厌氧消化产甲烷影响明显;餐厨垃圾中固有Na+含量对厌氧消化产甲烷影响不明显。     

浮萍与剩余污泥厌氧消化产沼气实验

为了提高浮萍厌氧消化产沼气能力,对比浮萍和剩余污泥的单独以及混合厌氧消化过程的产气情况,得到当两种底物混合厌氧消化时,具有互补优势,缩短了产甲烷过程的酸化期,累积产气量实际值比计算值提高11%。此外,研究底物的预处理以及底物与接种物比例对厌氧过程的影响,结果表明,浮萍经热碱预处理后比未处理组甲烷产量增加了8%,且厌氧消化产沼气时间缩短;当底物与接种物比例为1∶1时,整个反应过程的pH维持在6.00以上,利于产甲烷过程,体系中积累的挥发性脂肪酸(VFAS)最多,且获得的总沼气产量和总甲烷产量最大,分别为3 309 m L和1 883 m L,比最低的1∶2.5组分别高出151 m L和304 m L。     

垃圾渗滤液发酵产氢和产甲烷特性研究

以实际垃圾渗滤液作为厌氧发酵基质,研究了初始pH为7.0、中温(37℃)条件下的发酵产氢、产甲烷特性。结果表明,利用垃圾渗滤液作为基质发酵产氢或甲烷时,氢气的最大累积产量为24.33mL(以每克COD计,下同),甲烷的最大累积产量为91.59mL,产氢发酵在初期存在明显的迟滞期,但是产甲烷发酵不存在明显迟滞期;产氢发酵的液相末端产物中含有大量的挥发性有机酸和乙醇,乙醇、乙酸、丁酸质量浓度分别为487.23、1 175.21、1 225.78mg/L,相比产氢发酵,产甲烷发酵的液相末端产物中乙醇、乙酸、丁酸质量浓度均较低,分别为256.38、106.73、107.42mg/L;产甲烷发酵的最终pH是6.32,接近中性,而产氢发酵的最终pH为4.21,呈明显酸性;产甲烷发酵对COD的去除率(41.78%)高于产氢发酵对COD的去除率(32.14%),可能是产氢发酵液相末端产物中的乙酸能被产甲烷菌利用,而被进一步降解。     

pH值对玉米秸秆厌氧消化产气的影响

采用批式实验,研究了(35±0.5)℃、搅拌速度65 r/min的厌氧消化体系中,pH值对玉米秸秆厌氧消化产甲烷的影响,分析了消化液相及固相特性的变化.结果表明,厌氧消化第7～9天时各系统VFA浓度均达到最大值,pH值为7和9时,挥发性脂肪酸(VFA)浓度显著高于其他系统,SCOD向VFA的转化效率较高.pH值为9时累积产气量增加速度最快,最大累计产气量达到134.33 mL/g VS.pH值为7时累计产气量最大,高达149.2 mL/g VS,是pH值为5和11系统的3.23和6.71倍.pH值为7和9时,沼气中甲烷的平均含量分别为64.1％和62.5％,比pH值为5和11的系统提高了约10％.pH值为7和9时VS去除率达到67.68％和58.87％,显著高于其他系统.控制厌氧消化pH值在7～9范围内可以有效提高木质纤维素生物质的产气效率.     

糖蜜酒精废液厌氧生物降解生物化学甲烷势分析

在中温条件下,对pH值和营养比例2个影响因素进行了糖蜜酒精废液的BMP分析,探讨酒精废液在厌氧消化过程中产甲烷量、COD浓度的变化情况,以及COD去除率与产气量、pH值之间的关系.研究结果表明,厌氧处理法能够使糖蜜酒精废液的有机负荷大大降低,COD去除率最高可达90.6%.在调节营养比例的条件下,pH=8.5时甲烷菌活性最佳,其中COD:P=300:1的产甲烷量最高.     

木糖高温厌氧发酵产氢的影响因素及两相产氢-产甲烷的能量转化效率

通过批次实验,考查了木糖高温(55℃)厌氧发酵中初始pH(5.0~10.0)和初始底物浓度(2.5~15 g·L~(-1))对产氢效率、液相产物以及木糖降解率的影响;并进行了两相产氢-产甲烷实验,对比单相产甲烷与两相产氢-产甲烷能量转化效率。结果表明:在初始pH=5.0或初始底物浓度为2.5 g·L~(-1)时无氢气产生,最大产氢率1.31 mol H2·(mol木糖)-1在pH=7.0,底物浓度7.5 g·L~(-1)时获得,同时木糖降解率和累积产氢量分别为97.48%和328.4 mL;其主要代谢副产物为丁酸和乙酸,属于丁酸型发酵。厌氧产氢后末端产物甲烷产率为274.9 mL CH_4·(g COD)-1,两相系统能量转化效率达到63.98%,高于单相产甲烷系统的49.39%。     

污泥基生物炭对餐厨垃圾厌氧消化产甲烷及微生物群落结构的影响

为考察污泥基生物炭对餐厨垃圾厌氧消化的影响,以餐厨垃圾为基质,设置4种不同接种比(inoculum to substrate ratio, ISR)的批次实验,以得到不同酸化程度的厌氧消化体系;检测空白组、餐厨垃圾对照组和生物炭实验组的产甲烷情况和微生物群落结构的变化。结果表明:当ISR=2时,生物炭对餐厨垃圾厌氧消化效果不明显;当ISR=0.5时,生物炭使其停滞期缩短28.9%左右;ISR越小,生物炭对酸化停滞时间缩短以及产甲烷速率提高的效果越明显。同时,生物炭可以促进Chloroflex,Proteobacteria,Bacteroidetes的生长,从而提高厌氧消化中间产物的产生。当ISR较大时,厌氧消化系统的产甲烷途径以乙酸利用型为主,投加生物炭可以促进乙酸型产甲烷;随着ISR减小,产甲烷途径有逐渐向氢利用型转变的趋势,同时Methanosacrina逐渐替代Methanosaeta利用乙酸产甲烷。本研究结果可为污泥基生物炭在餐厨垃圾厌氧消化的实际应用提供参考。     

青岛市餐厨垃圾与菜市场垃圾混合高温厌氧消化研究

在中试规模下,研究青岛市餐厨垃圾与菜市场垃圾混合(质量比1∶1)高温厌氧消化实验,通过监测厌氧消化过程中产气量、气体组成等产气情况和消化液中pH值、SCOD、NH3-H、VFAs含量和组分等化学指标变化,确定混合厌氧消化的最大有机负荷,并分析混合高温厌氧消化技术的可行性,结果表明,(1)青岛市餐厨垃圾与菜市场垃圾混合高温厌氧消化产甲烷具有技术可行性;(2)混合厌氧消化的最大有机负荷可达4.069 kg VS/(m3.d);(3)当系统最大有机负荷时,每天每千克VS最高可产生甲烷量0.346 m3;(4)混合厌氧消化可削减氨氮对餐厨垃圾单独厌氧消化产沼气的影响。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

Phytoextraction of lead-contaminated soil using vetivergrass (<Emphasis Type="Italic">Vetiveria zizanioides</Emphasis> L.), cogongrass (<Emphasis Type="Italic">Imperata cylindrica</Emphasis> L.) and carabaograss (<Emphasis Type="Italic">Paspalum conjugatum</Emphasis> L.)

Background, Aims and Scope The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. Methods The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. Results On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. Discussion Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. Conclusions The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. Recommendations and Perspectives High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks. ESS-Submission Editor: Dr. Willie Peijnenburg (wjgm.peijnenburg@rivm.nl)