两种不同基质的垂直潜流人工湿地对尾水的处理效果研究

为提高人工湿地对污水处理厂尾水的处理效率,采用以黄铁矿和砾石为基质的两种垂直潜流人工湿地处理武汉某污水处理厂尾水,研究了不同水力负荷下人工湿地去除污染物的效果,并分析了基质的微生物群落结构。结果表明,在低水力负荷(0.4～0.7 m³/(m²·d))下,两种人工湿地对尾水化学需氧量(COD)、总氮(TN)、NO^-₃和总磷(TP)具有较好的去除效果;在高水力负荷(1.0～1.3 m³/(m²·d))下,对氨氮去除效果较好。黄铁矿人工湿地对尾水COD、TN、NO^-₃和TP的去除效果好于砾石,分析基质微生物发现,黄铁矿人工湿地中反硝化脱氮菌属主要为硫杆菌属(Thiobacillus)和硫氧化菌属(Sulfurifustis),相对丰度分别为16.68%和4.62%,且硫杆菌属具有提高磷去除能力的功能;而砾石人工湿地中反硝化脱氮菌属主要为类固醇杆菌属(Steroidobacter),相对丰度为4.56%,采用黄铁矿为基质...     

人工湿地基质中腐殖质的积累与分布特点

腐殖质来源于生物残体的降解,可参与多种污染物迁移转化,具有重要环境生态效应.本研究以常见的水平潜流和垂直流2种系统为研究对象,探讨了以无机基质为主构建的常规人工湿地中腐殖质的积累与分布特点.研究结果表明,随着污水处理运行,水平潜流和垂直流人工湿地中,大部分基质中腐殖质全碳量均有增加,水平潜流系统含量在1.7～ 18 g/kg,垂直流系统在1.9 ～7.5 g/kg;胡敏素是各系统腐殖质的主体组成,含量最高,水平潜流系统含量在1.55～17.22g/kg,垂直流系统在1.43 ～7.21 g/kg.腐殖质另外2种组分,富里酸和胡敏酸碳含量都比较低,水平潜流系统富里酸碳含量在0 ～0.68 g/kg,胡敏酸碳含量0.008 ～0.26g/kg;垂直流系统富里酸碳含量在0.015 ～0.38 g/kg,胡敏酸碳含量在0.05～0.15 g/kg,各系统中富里酸碳含量均高于胡敏酸碳含量;各系统中,根系基质腐殖质全碳及3种组分含量都显著高于非根际基质;不管是水平潜流还是垂直流,低水力负荷系统的比高水力负荷系统更高.     

复合垂直流人工湿地除磷正交试验研究

为了确定复合垂直流人工湿地的流程、水力负荷、pH、COD对TP去除率的影响和提高除磷效果,选择了美人蕉和风车草构建的复合垂直流人工湿地试验系统,开展除磷的正交试验研究。采用SPSS13.0软件对正交试验结果进行方差分析,确定各因素显著性及优选条件。结果表明,复合垂直流人工湿地流程、水力负荷、pH、COD对除磷效果均有影响,其中流程对TP去除率影响显著,COD对TP去除率影响不显著。各因素对TP去除率的影响程度依次为:流程水力负荷pHCOD。除磷优选条件:COD为225mg/L,pH为8,流程为1100mm,水力负荷为181.25L/(m2.d)。     

垂直潜流人工湿地有机物积累及去向初步分析

为防治湿地堵塞、改善湿地处理效果,初步探讨了湿地中有机物的积累规律,并估算湿地中有机物不同去除途径的贡献率。结果表明,垂直潜流人工湿地中基质间积累的有机物主要是不可溶有机物,且粒径主要集中在5.00μm以上,分析是不同粒径有机物凝聚积累的缘故;垂向沿程基质间有机物的积累量受进水水力负荷影响明显;进入垂直潜流人工湿地中的有机物绝大部分都被生物(植物和微生物)吸收和利用而得以去除,该途径贡献率可达99.9%以上。     

不同基质复合垂直流人工湿地对富营养化景观水的净化效果

研究了两套不同基质复合垂直流人工湿地小试装置在不同季节对富营养化景观水的净化效果,分析了温度变化对污染物去除效果的影响,考察了微生物的硝化强度和反硝化强度以及基质理化性质对植物生长状况的影响,并探讨了氮、磷的去除途径.结果表明:不同基质复合垂直流人工湿地随季节变化对浊度、COD和磷的去除效果差异不明显;温度降低对脱氮效果影响显著,对磷的去除影响不大.沸石-页岩湿地硝化强度和反硝化强度优于砾石湿地.采用沸石作为基质可以提高系统对氮的去除效率,促进湿地植物的生长.对氮、磷去除途径的分析表明:微生物的硝化反硝化作用以及基质对磷的吸附沉淀作用是复合垂直流人工湿地去除氮、磷的主要途径;植物吸收分别占湿地TN、TP去除量的16%和35%左右,也是个重要途径.     

阶段曝气和植物对人工湿地处理城镇污水厂尾水的影响

采用人工配水模拟城镇污水处理厂尾水水质,利用3套阶段曝气垂直潜流人工湿地(VSFCW)对其进行处理。结果表明:当水力负荷分别为30、90和180 cm·d-1时,3套人工湿地对COD具有较好的去除效果,其去除率都大于66.7%;在处理总磷(TP)和总氮(TN)方面,VSFCW-1(无植物-曝气垂直潜流人工湿地)去除效果远远低于VSFCW-2(芦苇-曝气垂直潜流人工湿地)和VSFCW-3(芦苇-不曝气垂直潜流人工湿地),VSFCW-2(芦苇-曝气垂直潜流人工湿地)和VSFCW-3(芦苇-不曝气垂直潜流人工湿地)对TP和TN的去除率分别在80.0%和75.0%以上且具有较强的抗水力负荷冲击能力。VSFCW-2(芦苇-曝气垂直潜流人工湿地)和VSFCW-3(芦苇-不曝气垂直潜流人工湿地)对COD、TP的去除主要是集中在沿程的前1/4段(0~24 cm),后3/4段(24~115 cm)保证了出水水质的稳定。     

钢渣-灰岩人工湿地脱除粪便污水高氮素的实验研究

构建小试系统研究了钢渣-灰岩垂直潜流人工湿地对粪便污水中高浓度氮素的降解效果。同时比较分析了填料填铺方式和表层填料对钢渣-灰岩垂直潜流湿地降解粪便污水氮素效能的影响。结果表明：当原水氨氮在42.72～272.60 mg/L,总氮在107.40～689.35 mg/L内,钢渣-灰岩垂直潜流人工湿地出水氨氮和总氮浓度可分别达到13.57 mg/L和62.83 mg/L;从长期效果来看,大级配差的正反粒径混合填铺的填料结构更有利于钢渣-灰岩人工湿地保持氮素降解效能;表层的基质材料选择要充分考虑渗透性和复氧能力;钢渣不但对氨氮有吸附作用,而且为氨氮的挥发和硝化/反硝化作用创造有利环境;灰岩在钢渣协助下溶出钙离子以利于氨氮的阳离子交换,同时为铁自养反硝化菌和脱硫杆菌的自养反硝化作用提供碳源。     

水力条件对复合人工湿地处理城市受污染河水效果的影响

通过对水力负荷、水力停留时间等水力条件的控制,观察其对复合垂直上行流人工湿地处理城市受污染河水效果的影响.一年多来的运行结果表明:水力条件对复合垂直上行流人工湿地去除其他污染物的影响显著,但对总氮去除的影响不大.水力停留时间的延长可提高总磷、氨氮、COD的去除效果;随着水力负荷的增加,总磷、氨氮、COD去除率都有所增加...     

出水口位置对垂直潜流人工湿地净化的影响

研究出水口位置对垂直潜流人工湿地净化的影响。垂直潜流人工湿地以间歇进水方式运行,进水水力负荷为0.125m3/(m2.d),进水来自南宁市琅东污水处理厂初沉池出水。研究结果表明,出水口位置对垂直潜流人工湿地净化有显著影响。与底部出水相比,中部出水的TN、SS和COD去除率分别提高了8.01%、8.48%、7.99%,出水NO-3-N质量浓度降低了9.38 mg/L;但NH+4-N去除率则降低了26.25%,TP去除率降低了21.21%。     

潜流人工湿地水力学特性及工程设计

以净化低污染水体的潜流人工湿地水力学特性工程设计为重点,系统开展了室内外实验研究,并利用Peelet数分析了水平潜流人工湿地碎石床渗流返混程度。结果表明,潜流人工湿地集水花管孔口出流计算、基质填料内渗流计算、碎石床平均水力停留时间计算可分别借鉴薄壁孔口恒定淹没出流、线性或非线性渗流、活塞流理论;但受工程实际条件及运行淤堵等影响,工程实测结果均小于理论计算值。基于室内外实验成果,提出一套包括集配水系统水力计算、填料内渗流计算、平均水力停留时间计算在内的潜流人工湿地水力学特性计算方法和参数选择,可为人工湿地技术的工程设计提供借鉴。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。