水污染分析校准用汞溶液的研制

研制了水污染分析校准用汞溶液。采用原子荧光光谱法对样品进行了均匀性和稳定性检验,对样品的量值进行了验证并进行了不确定度评定。检验结果表明:汞溶液均匀性良好,室温条件下可稳定36个月以上;样品的标准值为100 mg/L,扩展不确定度为2 mg/L。样品量值与美国AccuStandard公司同种标准物质具有一致性。可用于水中汞检测的测定标准、质量控制、分析方法研究以及实验室能力验证等方面。     

石灰石—石膏湿法脱硫浆液氟化铝络合原因分析及对策

石灰石—石膏湿法脱硫装置运行过程中,浆液氟化铝络合会影响石灰石的溶解度。以某电厂125MW燃煤机组脱硫改造工程为例,分析脱硫装置吸收塔浆液出现氟化铝缝合物造成石灰石闭塞的原因。依据A l3＋、F-络合原理及组分变化规律,及时采取技术措施,消除了石灰石闭塞,恢复脱硫装置正常运行。     

水性油墨废水絮凝污泥制备吸附剂及阳离子染料的吸附

以水性油墨废水絮凝污泥为原料、采用一步炭化活化法制备了吸附剂,并将其用于阳离子蓝X-GRRL溶液(300 mg/L)的吸附处理。考察了吸附剂投加量、吸附时间、吸附温度和吸附pH对吸附效果的影响,并对吸附动力学进行了探讨。结果表明:所制得吸附剂的总孔体积为0.5 cm~3/g,平均孔径为7.12 nm;在吸附剂投加量0.6g/L、吸附时间420 min、吸附温度25℃、吸附pH 5.4的条件下,吸附量高达486.21 mg/g,脱色率达97.24%;该吸附剂对于阳离子蓝X-GRRL的吸附过程可用准二级动力学模型和颗粒内扩散效应模型很好地描述。     

利用烟道气处理火电厂WFGD废水的技术应用

概述了火电厂湿法烟气脱硫废水的特点及其常规处理方法,介绍了一种利用烟道气对脱硫废水进行蒸发处理的技术方案。应用实践表明,利用烟道气蒸发处理脱硫废水是可行性的。     

Purification and Properties of a Poly (β-hydroxybutyrate) Depolymerase From Penicillium sp.

An extracellular poly (β-hydroxybutyrate) (PHB) depolymerase was purified from a Penicillium sp. DS9701-09a by centrifugation, ultrafiltration, precipitation and gel filtration chromatography. The specific activity of the purified enzyme was 37.9-folds higher than that of the culture supernatant and the recovery yield was 11.8%. The PHB deploymerase molecular mass was 44.8 kDa from analysis of both Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and Matrix-assisted laser desorption-time-of-flight (MALDI-TOF) mass spectrometer. The isoelectric point of 6.7 for the enzyme was determined by a two-dimensional electrophoresis. The optimum enzyme activity was observed at a temperature of 50 °C and pH 5.0. The apparent K _m of the enzyme was found to be 1.35 mg/mL. The PHB depolymerase consisted of 16 kinds of normal amino acids. The secondary structure of the enzyme was determined by CD spectrum. α-helix and β-turn were found to be 66% and 34% for the enzyme without ammonium sulphite. Chemical inhibition on the PHB depolymerase activity was examined and EDTA was found to have a significantly inhibitory effect.     

Pyrolysis characteristics of organic components of municipal solid waste at high heating rates

The pyrolysis characteristics of six representative organic components of municipal solid waste (MSW) and their mixtures were studied in a specially designed thermogravimetric analysis apparatus with a maximum recorded heating rate of 864.8 degrees Cmin(-1). The pyrolysis behavior of individual components was described by the Avrami-Erofeev equation. The influence of final temperature on individual components was studied, and it was concluded that final temperature was a factor in reaction speed and intensity, but that it played only a limited role in determining the reaction mechanism. The interactions between different components were evaluated, and it was concluded that the interaction between homogeneous materials was minimal, whereas the interaction between polyethylene and biomass was significant.     

锑污染土壤固化-稳定化的影响因素

通过比较不同稳定剂、固化剂、土壤pH条件下土壤中重金属锑的修复效果,研究了锑的固化-稳定化影响因素并探讨了相关稳定化机理.实验结果表明:铁基稳定剂的效果明显优于磷酸二氢钾和腐殖酸钠,而零价铁的稳定化效果更优于硫酸铁和硫酸亚铁,较适宜的稳定剂投加量为5％(w);水泥做固化剂对锑的稳定化效果优于氧化钙,最佳投加量为5％(w...     

某1000 MW燃煤机组脱硝催化剂运行性能检测

以某1000 MW燃煤机组脱硝系统使用的脱硝催化剂为研究对象,分别对不同运行时间的催化剂进行了对比检测。检测结果表明,运行初期,催化剂表面沉积了一定量的碱金属,但属于正常范围内;没有出现过多的硫化合物的沉积;催化剂微观结构遭到一定程度的破坏,比表面积有下降趋势;催化剂机械强度基本保持良好;催化剂活性衰减在正常范围内,催化剂可以继续使用或添加加装层。     

Fenton流化床陶瓷膜反应器处理造纸废水的膜污染与清洗

采用Fenton流化床陶瓷膜反应器处理造纸废水二级出水,研究了陶瓷膜膜污染的机理,提出了相应的清洗再生方案。实验结果表明:Fenton流化床陶瓷膜反应器处理后废水的溶解性有机碳和色度去除率分别达到84.2%和94.1%。通过Darcy定律模型计算,过滤阻力主要来自于滤饼层阻力,约占总阻力的62.1%;滤饼层中主要污染物为悬浮固体,约占滤饼层总质量的75.4%;疏水性有机物是造成滤饼层污染的主要溶解性有机物,而亲水性有机物更易造成膜孔堵塞;腐殖酸对滤饼层和膜孔堵塞影响较大,而蛋白质比多糖更易引起膜孔堵塞。采用HNO_3清洗污染膜效果最佳,在HNO_3质量分数1.00%、反应时间15 min时,膜通量恢复率达73.6%。     

Mass balances and life cycle inventory of home composting of organic waste

A comprehensive experimental setup with six single-family home composting units was monitored during 1 year. The composting units were fed with 2.6-3.5 kg organic household waste (OHW) per unit per week. All relevant consumptions and emissions of environmental relevance were addressed and a full life-cycle inventory (LCI) was established for the six home composting units. No water, electricity or fuel was used during composting, so the major environmental burdens were gaseous emissions to air and emissions via leachate. The loss of carbon (C) during composting was 63-77% in the six composting units. The carbon dioxide (CO(2)) and methane (CH(4)) emissions made up 51-95% and 0.3-3.9% respectively of the lost C. The total loss of nitrogen (N) during composting was 51-68% and the nitrous oxide (N(2)O) made up 2.8-6.3% of this loss. The NH(3) losses were very uncertain but small. The amount of leachate was 130 L Mg(-1) wet waste (ww) and the composition was similar to other leachate compositions from home composting (and centralised composting) reported in literature. The loss of heavy metals via leachate was negligible and the loss of C and N via leachate was very low (0.3-0.6% of the total loss of C and 1.3-3.0% of the total emitted N). Also the compost composition was within the typical ranges reported previously for home composting. The level of heavy metals in the compost produced was below all threshold values and the compost was thus suitable for use in private gardens.     

石横一期烟囱冲洗水及排液系统改造

介绍了石横电厂一期烟气脱硫技改项目中烟囱及入口烟道排液系统改造情况,论述了烟囱及烟道排液系统改造要点、运行方式,提出了烟囱排液系统的改造方案。     

A Novel Environmentally Compatible Bio-Based Product from Gelatin and Natural Rubber: Physical Properties

The objective of the present work was to study the preparation of a novel bio-based product from gelatin (GT) and natural rubber (NR) using potassium persulphate (KPS) as an initiator. The GT and NR composites (GT/NR composites) containing KPS were formed in an aqueous latex solution. The chemical structure of the GT/NR composite was characterized by ATR-FTIR, and XRD. The highest tensile strength was observed in a 9/1 GT/NR composite and the elongation at break of this composite was improved by the addition of both NR and glycerol. In addition, the swelling ratio increased as a function of increasing GT content in the composite. The thermal stability of the GT was improved after the formation of the chemical interaction between the NR and GT helped by the KPS. The best ratio of the GT/NR composite was 3/7 GT/NR. This environmentally friendly composite easily decomposed in natural soil within 30 days. The novel biopolymer showed high mechanical properties, water resistance and was produced in an environmentally compatible process. The NR was able to improve some of the physical and mechanical properties of GT biofilms produced from the composite. Possible future applications of this composite are for medical materials, and the packaging and life extension of food products.     

凹凸棒土吸附剂的制备和脱色性能研究

用以凹凸棒土为主料，配以其呛助剂所制备的凹凸棒土吸附剂，对癸二酸单钠盐 进行了吸附脱色和再生性能的试验，结果表明：该吸附剂具有明显的吸附脱色效果，且其制原料价廉易得，制备工艺简单，成本低，再生容易，是一种较好的脱色吸附型净化剂。     

BAF低温挂膜的影响因素分析

在低温条件下对曝气生物滤池(BAF)的挂膜进行了研究,考察了温度对曝气生物滤池挂膜的影响.结果表明,水温是低温挂膜的重要影响因素,低温条件下挂膜应采取保温措施,防止管路冻结,且对进水加热升温以促进微生物的生长.对挂膜期间曝气生物滤池去除有机物和NH3-N的情况进行了分析.     

碱性蚀刻废液的萃取电积再生

简要分析了碱性蚀刻废液的特点,总结了萃取电积法再生碱性蚀刻废液的基本原理,并进行了工程应用和环境效益分析。结果表明,碱性蚀刻再生液的蚀刻速率达60 m/min,蚀刻因子为3.5以上,回收铜纯度为99.95%。     

Combustion kinetics of sewage sludge and combustible wastes

This study estimated the kinetics of the mono- and co-combustion of sewage sludge pellets and combustible wastes such as municipal solid waste (MSW) and refuse-derived fuel (RDF). Sewage sludge was manufactured into pellets with a diameter of 8, 12, or 16 mm and a length of 30 mm. The RDF was composed of paper and plastics and was formed into pellets with a diameter of 8 mm and a length of 30 mm. MSW samples were synthesized using combustible wastes such as garbage, paper, plastics, and wood. The MSW was adjusted to have a moisture content of around 40% after shredding to under 10 mm. A laboratory-scale batch type stoker incinerator was used for the combustion and the gas composition of the flue gas was measured. The activation energy was calculated using the experimental results, and then the relation of the decomposition rate and reaction time was evaluated using the shrinking core model. The decomposition rate of the sludge pellets decreased as their diameter and moisture content increased, and the co-combustion of sludge pellets and combustible waste was affected by the amount of combustible waste. The individual combustion rates of the cylindrical sludge pellets or RDF were mainly controlled by the chemical reaction, but in the case of shredded MSW it was mostly influenced by gas diffusion. The rate for the co-combustion of sludge pellets and combustible wastes was mainly determined by the combustion rate of the combustible waste. The activation energy of the 8-mm-diameter sludge pellets was between 6.70 and 10.0 kcal/mol, according to the moisture content, but it was lower for MSW and RDF. In the case of MSW co-combustion, the reaction rate accelerated as the moisture content of the sludge pellets decreased, but it was markedly increased by the addition of RDF, regardless of the sludge moisture content.     

Tertiary recycling of PVC-containing plastic waste by copyrolysis with cattle manure

The corrosion from pyrolysis of PVC in plastic waste was reduced by copyrolysis of PVC with cattle manure. The optimization of pyrolysis conditions between PVC and cattle manure was studied via a statistical method, the Box-Behnken model. The pyrolysis reaction was operated in a tubular reactor. Heating rate, reaction temperature and the PVC:cattle manure ratio were optimized in the range of 1-5 degrees C/min, 250-450 degrees C and the ratio of 1:1-1:5, respectively. The suitable conditions which provided the highest HCl reduction efficiency were the lowest heating rate of 1 degrees C/min, the highest reaction temperature of 450 degrees C, and the PVC:cattle manure ratio of 1:5, with reliability of more than 90%. The copyrolysis of the mixture of PVC-containing plastic and cattle manure was operated at optimized conditions and the synergistic effect was studied on product yields. The presence of manure decreased the oil yield by about 17%. The distillation fractions of oil at various boiling points from both the presence and absence of manure were comparable. The BTX concentration decreased rapidly when manure was present and the chlorinated hydrocarbon was reduced by 45%. However, the octane number of the gasoline fraction was not affected by manure and was in the range of 99-100.     

Experimental research on emission and removal of dioxins in flue gas from a co-combustion of MSW and coal incinerator

This paper describes the experimental study of dioxins removal from flue gas from a co-combustion municipal solid waste and coal incinerator by means of a fluidized absorption tower and a fabric filter. A test rig has been set up. The flow rate of flue gas of the test rig is 150-2000 m3/h. The system was composed of a humidification and cooling system, an absorption tower, a demister, a slurry make-up tank, a desilter, a fabric filter and a measurement system. The total height of the absorption tower was 6.5m, and the diameter of the reactor pool was 1.2 m. When the absorbent was 1% limestone slurry, the recirculation ratio was 3, the jet rate was 5-15 m/s and the submerged depth of the bubbling pipe under the slurry was 0.14 m, the removal efficiency for dioxins was 99.35%. The concentration of dioxins in the treated flue gas was 0.1573 x 10(-13)kg/Nm3 and the concentration of oxygen was 11%. This concentration is comparable to the emission standards of other developed countries.     

煤气化细渣制备碳硅复合材料吸附去除水中Pb2+

以煤气化细渣为原料制备了高比表面积碳硅复合材料,并利用过硫酸铵对其进行表面改性,用于吸附100.0 mg/L PbCl₂溶液中Pb²⁺。表征结果显示：碳硅复合材料的比表面积为1 347 m²/g,改性后降为474 m²/g;改性后材料表面的羟基、羰基和羧基等含氧基团的含量显著增加。实验结果表明：溶液pH为5时,改性碳硅复合材料对Pb²⁺的平衡吸附量为124 mg/g,Pb²⁺去除率可达98.2%;吸附过程符合准二级动力学模型,以化学吸附为主,伴有物理吸附;吸附过程分为外扩散和内扩散两个阶段,受内扩散控制。     

全废砖再生轻骨料混凝土试验研究

将废粘土砖加工成粗细骨料,用于配制全废砖再生轻骨料混凝土.检测结果表明：所用废砖粗细骨料属轻骨料范畴,但其吸水率较大,且细骨料级配不良.试验表明：本试验配合比体系中,净水灰比为0.42,体积砂率为50％时最佳;以全废砖配制的再生砖轻骨料混凝土的强度发展规律与普通轻骨料混凝土类似,均有随水泥用量提高而强度提高的趋势,但随着所配制的混凝土强度等级的提高,再生轻骨料混凝土的强度提高趋势下降.以全废砖为骨料适合配制强度等级LC30及以下的再生轻骨料混凝土.