便携式烟气分析系统在燃煤电厂CEMS比对监测中的应用

按照《固定污染源烟气排放连续监测技术规范》（HT/T 75-2007）的要求,以Testo 350XL分析系统为例,介绍了便携式烟气分析系统在燃煤电厂CEMS比对监测的流程,分析实际监测中存在问题,提出了注意事项。     

Bioprocess technology for coal washery effluent treatment by Lemna minor

Duckweed species are promising macrophytes that can be used in wastewater treatment due to their rapid growth, ease of harvest, low fiber feed potential, and high protein contents. Waste‐water contaminants that are likely to be generated during washing of coal are total suspended solids (TSS), chemical oxygen demand (COD), acidity or alkalinity (pH), and metallic contaminants. Bioprocesses were developed to evaluate the potential of duckweed (Lemna minor) to treat coal washery effluent (CWE) as well as to study the impact on the biochemical changes of the Lemna minor. CWE samples were diluted with distilled water (DW) in different ratios as follows: T1‐CWE:DW(20:80%), T2‐CWE:DW(40:60%), T3‐CWE:DW(60:40%), T4‐CWE:DW (80:20%), T5‐CWE (100%), and Control‐DW(100%). The electrical conductivity of the effluent treated with Lemna minor was 0.035 deciSiemens per meter (dS/m) in the control at Day 10 and substantially higher at treatment ratios of 100, 80, and 60 percent (1.754, 1.842, and 1.631 dS/m). The highest amount of TSS was observed at test ratio T5 (38,834 mg/L), followed by T4 (28,816 mg/L), T3 (26,970 mg/L), T2 (15,320 mg/L), T1 (4,524 mg/L), and control (424 mg/L). Total hardness was higher (820 mg/L) in T4 compared to the control (220 mg/L). Total hardness of the effluent decreased after 30 days of incubation in all the treatment aliquots. The CWE at 20 percent concentration increased the duckweed population and no adverse impacts on its growth were observed. At higher concentration (T5) total mortality of Lemna minor was observed. The chlorophyll production was determined to be inversely proportional to the effluent concentration. Based on this study, it is concluded that Lemna minor can be used for treating CWE after dilution with fresh water.     

Effect of co-combustion on the burnout of lignite/biomass blends: a Turkish case study

Co-combustion of Turkish Elbistan lignite and woody shells of hazelnut was performed in a TGA up to 1173 K with a heating rate of 20 K/min. SEM images of each fuel revealed the differences in their physical appearances. Hazelnut shell was blended with lignite in the range of 2-20 wt% to observe the co-combustion properties. Maximum burning rates (Rmax), temperatures of the maximum burning rates (T(R-max)), and the final burnout values of the parent samples and the blends were compared. The results were interpreted considering lignite properties and the major biomass ingredients such as cellulosics, hemicellulosics, and lignin. Deviations between the theoretical and experimental burnout values were evaluated at various temperatures. Burnout characteristics of the blends up to 10 wt% were concluded to have a synergistic effect so the addition of hazelnut shell up to 8 wt% provided higher burnouts than the expected theoretical ones, whereas addition of as much as 10 wt% led to a decrease in the burnout. However, the additive effects were more favorable for the blend having a biomass content of 20 wt%. Apparent activation energy, Rmax, and T(R-max), were found to follow the additive behavior for the blend samples.     

T酸一次洗水初步处理的研究

采用重氮化－偶合－混凝沉淀和重氮化－混凝沉淀两种方法对Ｔ酸一次洗水的初步处理进步了研究。Ｔ酸一次洗水经两种方法处理后,ＣＯＤ去除率分别为６１．３％、５０．５％,色度去除率分别为７４．６％、７１％。     

厌氧消化-A/O-臭氧催化氧化-BAF工艺处理农药废水生化出水的中试研究

采用“厌氧消化-A/O-臭氧催化氧化-BAF”组合工艺对某农药企业污水处理站生化出水进行中试研究。中试装置设计处理规模为12 t/d,进水水质主要指标： COD为214~346 mg/L,ρ（NH₃-N）为8~35 mg/L,TN为65~108 mg/L。经组合工艺处理后,出水COD为51.2~71.4 mg/L,ρ（NH₃-N）为2.4~6.8 mg/L,TN为13.6~19.2 mg/L,出水水质可达到江苏省《化学工业主要水污染物排放标准》（DB 32/939-2006）中的一级标准。整套工艺对进水具有较强的耐冲击负荷能力,可适应难降解、高氮废水,具有较好的经济效益。     

The determination of biological stability of composts using the Dynamic Respiration Index: the results of experience after two years

Biological stability was ascertained by using the Dynamic Respiration Index (DRI) on 144 samples of compost during the years 2003 and 2004, as a routine service for private subjects. Data obtained were collected and are critically discussed in this paper by using other parameters registered during tests, i.e., biomass temperature (T), specific airflow rate (Qs) and biomass analytical data (pH). Good linear correlations were obtained for DRI vs. T, DRI vs. Q(s) and DRI vs. pH, confirming expected results based on the theoretical discussion. Consequently, using the analytical method proposed in this paper means both T and Q can be used as additional parameters for measurement of the biological stability of compost. As a result, T values of 25.8 and 30.5 degrees C, and specific airflow rate of 8.6 and 13.4 m3 Mg(-1) VS h(-1) were found corresponding to 500 and 1000 mg O2 kgVS(-1) h(-1), which, respectively, indicate a high and a medium degree of biological stability.     

Effectiveness of Capture Zones Generated by Intermittent Pumping of a PV‐Powered Pump‐and‐Treat System Without Energy Storage

A common technology to remediate and/or contain contaminated groundwater is pump‐and‐treat remediation (P&T). Traditionally, P&T systems have been designed to operate continuously to achieve steady‐state capture zones, for which large amounts of energy are required. Green and sustainable remediation (GSR) is emerging as a viable method to minimize the adverse effects of remediation on the environment. One of the challenges associated with photovoltaic‐ (PV‐) powered P&T systems is the assessment of their performance given the intermittent nature of the power availability. This article characterizes the hydraulic containment effectiveness of a PV‐powered P&T system without energy storage using data collected at two different remediation sites, a Dry‐Cleaning Environmental Response Trust Fund site in Rolla, Missouri, and the Former Nebraska Ordnance Plant near Mead, Nebraska. Additionally, a method to estimate the effectiveness of the hydraulic containment as a function of the total volume of groundwater expected to be extracted is being proposed. Two transient and a continuously pumped capture zones were modeled using Visual MODFLOW^® 2012.1 along with MODPATH and compared. The study shows that smaller capture zones will be generated from intermittent pumping when compared to continuous pumping. © 2013 Wiley Periodicals, Inc.     

Purification and characterization of extracellular poly(3-hydroxybutyrate) depolymerases

Five extracellular PHB depolymerases of bacteria isolated from various sources were purified to electrophoretic homogeneity and compared with known extracellular PHB depolymerase fromAlcaligenes faecalis T1. The molecular mass of these enzymes were all around 40–50 kDa. Nonionic detergent, diisopropylfluorophosphate and dithiothreitol inhibited the PHB depolymerase activity of all these enzymes. Trypsin abolished PHB depolymerase activity, but not theD-3-hydroxybutyric acid dimer hydrolase activity of all the enzymes. These results showed that the basic properties of these PHB depolymerases resemble those of theA. faecalis T1 enzyme. Analysis ofN-terminal amino acid sequence of the purified enzymes revealed that these enzymes includingA. faecalis T1 enzyme fall into three groups.     

Influence of waste input and combustion technology on MSWI bottom ash quality

The waste input and the process technology of waste incineration plants appear to have a great influence on bottom ash quality. To better understand how these parameters can affect the characteristics of residues, bottom ash from six plants were tested and compared in this study. Bottom ash physico-chemical characteristics were investigated by chemical analyses, and leaching tests. In order to understand their long-term behavior, accelerated ageing experiments and biodegradation tests were also performed. The whole analyses gave complementary information. It was shown that the six samples do have different properties. Waste inputs have a great influence on Cl and S content in bottom ash, as well as on the Ca/Si ratio. The importance of this ratio on the carbonation process has been demonstrated. Combustion parameters have an influence on the quantity and mobility of the residual organic matter.     

Emission of volatile sulfur compounds during composting of municipal solid waste (MSW)

Volatile sulfur compounds (VSCs) are the main source for malodor from composting plants. In this study, the VSCs generated from composting of 15–80 mm municipal solid waste (T0), kitchen waste (T1) and kitchen waste mixed dry cornstalks (T2) were measured in 60 L reactors with forced aeration for a period of 30 days. The VSCs detected in all treatments were hydrogen sulfide (H₂S), methyl mercaptan (MM), dimethyl sulfide (DMS), carbon bisulfide (CS₂) and dimethyl disulfide (DMDS). Over 90% of the VSCs emissions occurred during the first 15 days, and reached their peak values at days 4–7. The emission profiles of five VSCs species were significantly correlated with internal materials temperature and outlet O₂ concentration (p < 0.05). Total emissions of the VSCs were 216.1, 379.3 and 126.0 mg kg^?1 (dry matter) for T0, T1 and T2, respectively. Among the five VSCs, H₂S was the most abundant compound with 39.0–43.0% of total VSCs released. Composting of kitchen waste from separate collection posed a negative influence on the VSC and leachate production because of its high moisture content. An addition of dry cornstalks at a mixing ratio of 4:1 (wet weight) could significantly reduce the VSCs emissions and avoid leachate. Compared to pure kitchen waste, VSCs were reduced 66.8%.     

Integrated geophysical surveys on waste dumps: evaluation of physical parameters to characterize an urban waste dump (four case studies in Italy).

Geophysical surveys were carried out on different waste dumps to evaluate key geometric and physical parameters. Depending on the dump dimensions and physical characteristics different geophysical techniques were used. Vertical electrical sounding, electrical resistivity tomography, induced polarization and seismic refraction techniques were integrated to eliminate the non-uniqueness of solutions and for a better understanding of the results. Physical parameters inside and outside the dumps were compared. The change of physical parameters such as resistivity, chargeability, and P-wave velocity allowed evaluation of waste dump geometry, leachate saturation levels, and thickness of waste. Furthermore, in illegal dumps, the size and waste type disposed could be evaluated. Calculated results were compared with plans and book-keeping from the dumps investigated.     

Characterization and recovery of mercury from spent fluorescent lamps

Fluorescent lamps rely on mercury as the source of ultraviolet radiation for the production of visible light. Partitioning of mercury among vapor phase, loose phosphor powders produced during breaking and washing steps, glass matrices, phosphor powders attached on the glass and aluminum end caps was examined from simulated laboratory lamp recycling tests for different types of spent and new fluorescent lamps. Mercury concentrations in lamp glasses taken from commercial lamp recyclers were also analyzed for comparison with the simulated results of spent and new lamps of different types. The mercury content of the glass from spent lamps was highly variable depending on the lamp type and manufacturer; the median values of the mercury concentration in glasses for spent 26- (T8) and 38-mm (T12) diameter fluorescent lamps were approximately 30 and 45 microg/g, respectively. The average mercury concentration of samples taken from recycler A was 29.6 microg/g, which was about 64% of median value measured from the spent T12 lamps. Over 94% of total mercury in lamps remained either as a component of phosphor powders attached inside the lamp or in glass matrices. New T12 lamps had a higher partitioning percentage of elemental mercury in the vapor phase (0.17%) than spent T12 lamps (0.04%), while spent lamps had higher partitioning percentages of mercury resided on end-caps and phosphor powders detached from the breaking and washing steps. The TCLP values of simulated all lamp-glasses and samples obtained from recyclers were higher than the limit of LDR standard (0.025 mg/L). After investigating acid treatment and high temperature treatment as mercury reclamation techniques, it was found that heating provided the most effective mercury capture. Although the initial mercury concentrations of individual sample were different, the mercury concentrations after 1 h exposure at 100 degrees C were below 4 mug/g for all samples (i.e., <1% remaining). Therefore, it is recommended that heating be used for recovering mercury from spent fluorescent lamps.     

Studies on the enzymatic and fungal degradation of cross-linked gelatin and its graft copolymers

Glutaraldehyde cross-linked gelatin was graft copolymerized with acrylic acid, acrylamide, vinyl acetate, methyl acrylate, and methyl methacrylate either individually or in combination. The enzymatic and fungal degradation of these graft copolymers with trypsin, pepsin, and mixed cultures ofAspergillus niger, Penicillium ochrochloron, Penicillium funiculosum, andTrichoderma viride was studied for short and extended periods. The weight loss suffered by the samples, the weight of biomass formed, the nitrogen content, and the pH of the culture medium were determined. With the help of these data, the extent of utilization of graft copolymers by fungi as a sole source of carbon was estimated. The samples with less than 100% grafting and with a ratio of polymethyl methacrylate content (L) to polyacrylic acid (H) content (L/H values) lower than 1.0 were readily and extensively degraded.IICT Communication No. 3375.     

Extractability and leachability of heavy metals in Technosols prepared from mixtures of unconsolidated wastes

Mixtures of wastes were prepared to improve on the characteristics of the individual ingredients as Technosols, with special attention given to heavy metal extractability. An anaerobic digested sewage sludge and a CaO-treated aerobic sludge were used. A mixture of the two sludges (50:50 DW basis) was also prepared to provide a third type of sludge. The residues were mixed with other types of waste, such as fly ash, Linz-Donowitz slag, foundry sand, shot blasting machine scrap, fettling and barley straw. Extractability of Cu, Cr, Ni, and Zn by 0.01 M CaCl(2) extraction (Me(CACI(2)) was carried out, and leachability of these elements was estimated by acidification of an aqueous suspension of the mixtures with 0.5 N acetic acid (Me(acetic)). The total concentrations of the metals were also determined (Me(T)). The Me(CACI(2)/Me(T) ratios for Cu and Ni (means: 4.0% and 3.1%) were higher than those for Cr and Zn (means: 0.07% each). The mean Me(acetic)/Me(T) ratios followed the order Ni, Zn, Cu, and Cr (19.5%, 4.1%, 3.7%, and 0.09%, respectively). The results highlight the existence of complex interactions among organic matter solubility, pH and heavy metal extractability.     

Comparing the Growth Characteristics of Three Bacteria Involved in Degrading Rubbers

Three bacteria isolated for degradation of rubbers were compared for their growth characteristics derived from the Bradford protein assay and turbidity (optical density, OD) measurement. Both Alcaligenes xylosoxidans T2 and Pseudomonas aeruginosa GP10 were fast-growing bacteria while Nocardia corynebacterioides S3 was a slow grower utilizing rubber as the sole source of carbon and energy, but the extent of degradation was lower by the formers than the latter. A. xylosoxidans T2, P. aeruginosa GP10 and N. corynebacterioides S3 showed a typical sigmoidal growth pattern based on binding of Coomassie Brilliant Blue G250 to bacterial proteins and spectrophotometrical measurement at 600 nm. Both assays showed similar growth characteristics for all three bacteria in this study. Degradation of rubber was more pronounced by N. corynebacterioides S3 than either A. xylosoxidans T2 or P. aeruginosa GP10 during 70 days of incubation. Our results suggest that slow-growing bacteria may play a much greater role in degrading polymeric materials than was previously believed.     

Multi-criteria decision analysis for waste management in Saharawi refugee camps

The aim of this paper is to compare different waste management solutions in Saharawi refugee camps (Algeria) and to test the feasibility of a decision-making method developed to be applied in particular conditions in which environmental and social aspects must be considered. It is based on multi criteria analysis, and in particular on the analytic hierarchy process (AHP), a mathematical technique for multi-criteria decision making (Saaty, T.L., 1980. The Analytic Hierarchy Process. McGraw-Hill, New York, USA; Saaty, T.L., 1990. How to Make a Decision: The Analytic Hierarchy Process. European Journal of Operational Research; Saaty, T.L., 1994. Decision Making for Leaders: The Analytic Hierarchy Process in a Complex World. RWS Publications, Pittsburgh, PA), and on participatory approach, focusing on local community’s concerns.The research compares four different waste collection and management alternatives: waste collection by using three tipper trucks, disposal and burning in an open area; waste collection by using seven dumpers and disposal in a landfill; waste collection by using seven dumpers and three tipper trucks and disposal in a landfill; waste collection by using three tipper trucks and disposal in a landfill.The results show that the second and the third solutions provide better scenarios for waste management. Furthermore, the discussion of the results points out the multidisciplinarity of the approach, and the equilibrium between social, environmental and technical impacts. This is a very important aspect in a humanitarian and environmental project, confirming the appropriateness of the chosen method.     

Improvement of digestibility of sunflower and corn residues by some saprophytic fungi

The in vitro degradation of fiber from two agricultural residues (Helianthus annuus and Zea mays) was studied using four saprophytic fungi. The changes in cellulolytic enzyme and phosphatase activities, the C/N ratio, the dry weight, the crude fiber (CF) content, and the protein and fiber digestibility coefficients were investigated in solid-state culture during a 45-day period of biodegradation. The FPase activity of Phanerochaete chrysosporium and the endoglucanase activities of P. chrysosporium and Trichoderma reesei compared to those of the other fungi were significantly (P < 0.05) high on both crop resides. Both acid and alkaline phosphatases were produced in greater amounts by P. chrysosporium than by the other fungi. The organic carbon contents of both residues were reduced more by T. reesei than by the other fungi. The fiber digestibility coefficient of untreated corn residue was higher than that of sunflower residue, but after treatment with fungi, the sunflower fiber digestibility increased more than that of corn did. Although the CF contents of both residues were decreased more by P. chrysosporium than by T. reesei, the fiber digestibility coefficients of both residues were increased more by T. reesei than by P. chrysosporium. The treatment of both crop residues increased their protein digestibility coefficients significantly compared to the control. The protein digestibility coefficients of both residues were increased more by T. reesei and P. chrysosporium than by the other fungi. In all treatments, the protein digestibility coefficient of sunflower residue was higher than that of corn residue.     

Comparison of three ornamental plants for phytoextraction potential of chromium removal from tannery sludge

Based on pre-experimentation, three ornamental plants, Mirabilis jalapa, Impatiens Balsamin (I. Balsamin) and Tagetes erecta L., were selected as target plants to study the phytoextraction of chromium (Cr) in tannery sludge irrigated with four treatments according to Cr concentration gradient [Control (CK); 20.50 × 10³ mg kg^?1 (T1); 51.25 × 10³ mg kg^?1 (T2); 102.50 × 10³ mg kg^?1 (T3)]. Results of pot experiments showed that the biomass of Mirabilis jalapa and Tagetes erecta L. had no significant differences among the four treatments, while I. Balsamin showed a decline trend in the biomass with the increase of Cr concentration, probably due to some extent to the poisoning effect of Cr under treatment T2 or T3. Mirabilis jalapa accumulated Cr concentration, with 408.97, 124.97, 630.16 and 57.30 mg kg^?1 in its roots, stems, leaves and inflorescence, respectively. The translocation factor and the bioaccumulation coefficient of Mirabilis jalapa are each greater than 1, indicating that Mirabilis jalapa has the strong ability to tolerate and enrich Cr by biological processes. Comparing accumulation properties of the three ornamental plants, in the amount and allocation, Mirabilis jalapa showed the highest phytoextraction efficiency and could grow well at the high Cr concentration. Our experiments suggest that Mirabilis jalapa is the expected flower species for Cr removal from tannery sludge.     

用棉籽壳制乙酰丙酸及活性炭

棉籽壳经加酸加热水解,制得乙酰丙酸,收率为16．2％;残渣经硫酸炭化磺化,制得木素活性炭,收率为81．2％,脱色性能优于国家标准GB／T12496．22－90）。