V/Ce共掺杂TiO2光催化降解甲醛的实验研究

采用溶胶凝胶法制备了不掺杂、V 掺杂、Ce掺杂、V/Ce共掺杂纳米TiO₂光催化剂,并将其分别负载于瓷砖上,利用X射线衍射分析（XRD）和扫描电镜分析（SEM）技术对薄膜样品的结构和形貌进行了表征。通过对甲醛的降解实验评价光催化剂的光催化活性。实验结果表明,光催化剂的负载量、共掺杂离子的掺杂量、掺杂配比、煅烧温度影响纳米TiO₂的光催化活性。V/Ce共掺杂TiO₂光催化剂产生了协同效应,其光催化活性优于纯TiO₂和单掺杂TiO₂样品。     

溶胶-凝胶法制备复合光催化剂（MWNTs/ TiO2）工艺条件的研究

以多壁碳纳米管（MWNTs）为载体,在煅烧温度200~900℃、煅烧时间1~7 h、溶胶体系pH值为2~10的工艺条件下,采用溶胶-凝胶法制备复合光催化剂（MWNTs/TiO₂）。通过其对甲基橙的光催化降解效果对比,评价各种复合光催化剂催化活性之间的差异,结果表明,随着煅烧温度的升高,复合光催化剂中纳米TiO₂的晶型由锐钛型逐渐向金红石型转变,500℃时为2种晶型的混合相;pH值为2的强酸性条件有利于形成金红石晶型,pH值为5的中性及弱酸性条件则有利于形成锐钛型,而pH值为3时为2种晶型的混合相;在煅烧温度500℃、煅烧时间3 h、溶胶凝胶体系pH值为3的最佳制备工艺条件下,复合光催化剂催化活性最高,借助扫描电镜发现其TiO₂均匀地包覆在多壁碳纳米管管壁上。     

多壁碳纳米管结构对复合光催化剂催化效果的影响

采用溶胶凝胶法制备了多壁碳纳米管负载纳米TiO₂的复合光催化剂（TiO₂/MWCNTs）,以偶氮类染料甲基橙为目标污染物,在自制的光催化反应器上进行了光催化降解反应实验。主要研究同一甲基橙初始浓度（C₀)下,多壁碳纳米管不同管长和管径对复合光催化剂催化效果的影响。结果表明：该降解反应可用一级反应动力学方程描述,反应速率常数k随着多壁碳纳米管管长和管径的增大而增大;与纯纳米TiO₂相比,复合光催化剂对甲基橙的降解率提高了6％～18％,反应速率常数为前者的1.19～2.11倍;采用复合光催化剂的甲基橙光降解溶液自行沉降分离效果较好,静止沉降60 min后达到沉降平衡,剩余浊度为8.5 NTU,下降了90.6％。     

锰掺杂WO3-TiO2复合光催化剂的制备及其性能研究

溶胶-凝胶和浸渍相结合的方法制备锰掺杂WO₃-TiO₂复合光催化剂，RXD表征，考察WO₃和Mn²⁺掺入量、焙烧温度、焙烧时间及催化剂用量对光催化降解甲基橙的影响。结果表明，500℃焙烧2h，掺杂量n_{（Mn²⁺）}∶n_（WO3）∶n_（TiO2）＝0.8∶1∶100时，光催化活性最高，光催化降解甲基橙溶液，120min后，降解率达90%, 比单纯 TiO₂的光催化活性提高81%。     

负载型纳米复合半导体WO3-TiO2/AC光催化降解刚果红废水

采用溶胶-凝胶-浸渍-焙烧法制备了负载型纳米复合半导体WO₃-TiO₂/AC光催化剂,以偶氮染料刚果红为目标降解物,通过正交实验优化了刚果红废水的降解条件,并对其光催化动力学进行了探讨。结果表明,刚果红废水的最佳降解条件为：催化剂投加量10 g/L,pH=7,H₂O₂用量为3.5 mL/L。在最佳条件下,当刚果红废水起始浓度为40 mg/L时,反应120 min后,刚果红溶液的去除率可达95.21%,较相同条件下TiO₂/AC对刚果红染料的降解率提高了19.57％。光催化剂对刚果红的光催化降解符合Langmuir-Hinshelwood（L-H）模型。     

纳米Bi2O3/TiO2复合光催化剂的制备及性能研究

以光催化效果为评价标准,采用超声波作用下水解法制备Bi₂O₃/TiO₂复合光催化剂,考察了水解条件和Bi₂O₃掺入量等制备条件对复合光催化剂性能的影响。结果表明,与传统制备方法相比,该方法操作简单、快速;当水和乙醇的比例为4∶1时所得样品的光催化活性最好;Bi₂O₃的掺入拓宽了TiO₂对光的吸收范围,提高了TiO₂的光催化活性,掺入量(Bi₂O₃)为0.25%复合光催化剂催化活性最高;复合光催化剂对多种水溶性染料均具有较好的处理效果。     

银钛共负载型光催化材料降解甲基橙废水简

以膨胀珍珠岩为载体,采用溶胶凝胶法对其进行负载,制备出不同类型的光催化材料（TiO₂-EP、Ag⁺-TiO₂-EP）,并在模拟日光条件下,研究其对甲基橙溶液的降解效果。结果表明,浸渍3次且担载0.04% Ag⁺的负载型TiO₂光催化活性最高,在光催化剂用量为0.3 g,20 mL初始浓度为10 mg/L甲基橙溶液光照4 h后降解率可达81.6%,且甲基橙的光催化降解服从一级动力学方程。回收3次后仍有较强的活性,其2 h降解率为24.8%。     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶凝胶法制备TiO₂/beads光催化剂载体,然后浸渍法制备出H₄SiW₁₂O₄₀/TiO₂/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H₄SiW₁₂O₄₀/TiO₂/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明,在中性条件下,H₄SiW₁₂O₄₀/TiO₂/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

La2O3/ZnO/TiO2光催化降解活性艳红K-2BP的研究

采用溶胶-凝胶法制备了La₂O₃/ZnO/TiO₂复合光催化剂,以紫外灯为光源,活性艳红K-2BP为模型降解物,研究了La₂O₃/ZnO/TiO₂的光催化性能。结果表明：当锌和镧的掺杂量w(ZnO)=20%, w(La₂O₃)=0.5%, 煅烧温度为500℃时,La₂O₃/ZnO/TiO₂复合光催化剂的光催化活性最高;当催化剂投加量4 g/L,通气量800 mL/min,初始pH值3.12时,La₂O₃/ZnO/TiO₂对活性艳红K-2BP的降解效果最好。实验证明,La₂O₃/ZnO/TiO₂对活性艳红K-2BP的降解遵从Langmuir-Hinshelwood动力学模型,测得其反应速率常数k＝11.5 mg/(L·min);吸附常数K＝2.88×10^-2 L/mg。     

掺硫改性TiO2对活性艳红X-3B的光催化降解性能研究

以硫脲为硫的源物质,以钛酸四丁酯为TiO₂的前驱体,采用溶胶-凝胶法制备了掺硫改性TiO₂光催化剂。以活性艳红X-3B为目标污染物,研究了该催化剂的光催化降解性能,对硫掺杂量、催化剂焙烧温度、溶液pH值以及催化剂添加量等影响因素进行了研究,并采用XRD分析手法对光催化剂进行表征。结果表明,经掺硫改性后的TiO₂的催化活性有了很大提高,且硫的掺杂有一个最佳值,即Ti∶S的摩尔比为1∶1。经掺硫改性的TiO₂在可见光区具备一定的催化活性, 180 min内对活性艳红X-3B的去除率可达35.1%,且在紫外光区的催化活性优于纯TiO₂。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

Phytoextraction of lead-contaminated soil using vetivergrass (<Emphasis Type="Italic">Vetiveria zizanioides</Emphasis> L.), cogongrass (<Emphasis Type="Italic">Imperata cylindrica</Emphasis> L.) and carabaograss (<Emphasis Type="Italic">Paspalum conjugatum</Emphasis> L.)

Background, Aims and Scope The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. Methods The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. Results On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. Discussion Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. Conclusions The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. Recommendations and Perspectives High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks. ESS-Submission Editor: Dr. Willie Peijnenburg (wjgm.peijnenburg@rivm.nl)