Degradation of dyestuff wastewater using visible light in the presence of a novel nano TiO2 catalyst doped with upconversion luminescence agent

IntroductionEvery year ,the dyeing processes and dye productionbring large amounts of wastewaters containing highconcentration poisonous organic compounds ( Neppolian,2002 ; An, 2002) . If not being treated properly andbetimes , the wastewaters will serio…     

活性炭负载TiO2催化剂对直接耐酸大红4BS溶液的光催化降解研究

采用溶胶-凝胶法制备了活性炭负载型TiO2催化剂,采用了XRD、BET和SEM对催化剂进行表征。研究了催化剂对直接耐酸大红4BS的紫外光催化降解,比较了活性炭、P25和TiO2／AC对4BS溶液的降解能力,探讨了催化剂煅烧温度和投加量以及染料溶液的初始浓度对光催化降解率的影响,并对催化剂进行了回收再生实验。结果表明,500℃下煅烧的TiO2／AC催化剂比表面积为1147．88m^2／g、TiO2粒径为21．9nm、晶相组成以锐钛矿为主,具有良好的光催化活性和稳定性;90min后2g／L催化剂对150mg／L的4BS溶液紫外光催化降解率达到99．8％。     

新型纳米材料光催化反应器研究

为了充分发挥纳米材料的光催化性能,研制了一种带有旋转叶片且可负载光催化纳米材料的光催化反应器.并以制备的纳米TiO2/硅藻土复合材料作为光催化剂、TNT生产废水为处理对象,考察了催化材料附载量、废水浓度和多次重复使用对反应器催化降解效率的影响.结果表明:附载有光催化纳米材料的反应器经过6次6h重复使用,对TNT生产废水催化降解效率仍然保持在75%以上,远高于直接分散在废水中纳米材料的处理效率(47.25%),即多次重复使用并保持高降解效率;而且可较好地避免纳米光催化材料的团聚.避免因回收造成的纳米材料光催化效率降低以及回收不完全造成的水体二次污染等现象.     

TiO2/beads as a photocatalyst for the degradation of X3B azo dye

The feasibility of photocatalytic degradation of X3B azo dye by TiO2/beads photocatalyst was studied.The effects of parameters such as the amount of TiO2/beads,airflow ,as well as the concentrations of H2O2,Fe^3 ,Mg^2 and Na^ on the photocatalytic degradation of X3B azo dye were also studied.The results showed that 25mg/dm^3 X3B azo dye can be photocatalytically degraded completely by 30 min illumination with a 375W medium pressure mercury lamp.Adding a small amount of H2O2 or Fe^3 ,the efficiencies of photocatalytic degradation of X3B azo dye were increased rapidly.The mechanisms of the reaction and the role of the additives were also investigated.After 120 hours TiO2/beads showed no significant loss of the photocatalytic activity.     

TiO_2/beads as a photocatalyst for the degradation of X_(3B) azo dye

ＩｎｔｒｏｄｕｃｔｉｏｎＥｎｖｉｒｏｎｍｅｎｔａｌｐｒｏｔｅｃｔｉｏｎｅｘｐｅｒｔｓｉｎｍａｎｙｃｏｕｎｔｒｉｅｓｐａｙｈｉｇｈａｔｔｅｎｔｉｏｎｔｏｔｈｅｄｉｓｐｏｓａｌｏｆｔｈｅｗａｓｔｅｗａｔｅｒｗｉｔｈｄｙｅｏｒｗｉｔｈｄｅｅｐｃｈｒｏｍａ.Ｔｈｏｕｇｈａｔｐｒｅｓｅｎｔｂｉｏｄｅｇｒａｄａｔｉｏｎｉｓｕｓｅｄｉｎｔｈｅｄｉｓｐｏｓａｌｏｆｔｈｅｗａｓｔｅｗａｔｅｒ,ｔｈｅｃｏｎｃｅｎｔｒａｔｉｏｎａｎｄｃｈｒｏｍａｉｎｔｈｅｄｉｓｐｏｓｅｄｗａｔｅｒａｒｅｓｔｉｌｌｖｅｒｙｈｉｇｈａｎｄ…     

Activated carbon supported TiO2-photocatalysis doped with Fe ions for continuous treatment of dye wastewater in a dynamic reactor

Fe-doped TiO2 coated on activated carbon (Fe-TiO2/AC, FTA) composites were prepared by an improved sol-gel method and characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, X-ray di ractometry, inductively coupled plasma mass spectrometry and BET surface area analysis. Obtained FTA composites were applied to the continuous treatment of dye wastewater in a dynamic reactor. The e ects of Fe ion content, catalyst content, UV-lamp power and flowrate of the continuous treatment of dye wastewater on degradation e ciency were analyzed to determine the optimum operating conditions of dye wastewater degradation. Continuous photocatalytic experiments provided interesting results that FTA had a high chemical oxygen demand (COD) removal rate compared with TiO2, Fe doped TiO2 (FT) and TiO2 coated on activated carbon (TA). In particular, when using the FTA catalyst with a Fe ion content of 0.33%, the kinetic content (k = 0.0376) of COD removal was more than the sum of both TA (0.0205) and 0.33% FT (0.0166). FTA showed a high photoactivity because of a synergistic e ect between Fe ions and AC on TiO2, which is higher than the individual e ects of AC or Fe ions on TiO2. Additionally, for the photocatalytic degradation of dye wastewater, the optimum Fe ion content, catalyst content, UV-lamp power and flowrate were 0.33%, 6 g/L, 60 W (two lamps) and 300 mL/hr, respectively. An investigation of catalyst reuse revealed that the 0.33% FTA showed almost no deactivation in photocatalytic degradation of naturally treated wastewater.     

流化床光催化反应器处理偶氮染料4BS废水中试研究

采用 3 0～ 40目负载型光催化剂 ,以高压汞灯为紫外光源 ,研究了偶氮染料 4BS废水在流化床光催化中试反应器中的降解 ,针对有关工艺参数和反应动力学进行了考察。结果表明 :所用中试反应器对 4BS具有较好的降解效果 ;催化剂浓度存在最佳值 ;适当增加光强及溶解氧浓度均有利于光催化降解效率的提高 ;染料 4BS溶液的光催化降解过程符合表现一级反应动力学规律 ,并且表观反应速率常数与 4BS初始浓度之间具有近似负一级的动力学关系     

流化床光催化氧化处理印染废水中试研究

设计了1种流化床光催化氧化中试处理系统,制备了一种负载型TiO₂光催化剂.以高压汞灯为光源,选用难降解偶氮染料4BS和高分子化学浆料CMC配制的模拟印染废水为处理对象,考察了初始pH值、初始浓度以及光助催化剂H₂O₂浓度、Fe₃₊浓度对光催化降解效果的影响,并对有关的光催化反应动力学规律进行了探讨.结果表明,本工艺系统对配制的印染废水有较好的处理效果,光照74min色度去除率可超过80%,光照150min COD去除率可超过70%,BOD₅/COD可提高至0.4以上.     

锰离子掺杂纳米二氧化钛的制备及在造纸废水处理中的应用

以无机盐无水四氯化钛为原料,采用溶胶-凝胶法制备的锰离子掺杂型纳米TiO2作为光催化剂,在高压汞灯的光源照射下对河北省某造纸厂废水进行光催化降解。考察Mn2+/TiO2光催化剂的热处理温度、掺杂量、用量及溶液pH值、光照时间等因素对废水COD降解率的影响。实验结果表明:经460℃热处理1h的Mn2+/TiO2光催化效果较好,在进水ρ(COD)为400 mg/L,初始pH值为4.0、光催化剂用量1.5g/L、光照时间9h条件下,COD去除率可达80.3%。经深度处理的造纸废水,可实现达标排放。     

TiO2光催化剂载体及提高其光催化活性的研究进展

光催化技术是一种新型的绿色环保技术,TiO2是光催化反应中的一种研究较为广泛的光催化剂,其在污水处理以及空气净化等领域具有广泛的应用前景。文章综述了TiO2作为光催化剂的研究现状,着重介绍了TiO2光催化剂载体的研究及TiO2的改性研究。并结合我们在TiO2载体以及提高其催化活性方面所作的一些研究工作,提出一些看法。     

H_3PW_(12)O_(40)/TiO_2可见光下光催化降解孔雀石绿的研究

以钛酸四丁酯为原料,采用溶胶-凝胶法制备TiO2光催化剂,然后浸渍法制备出H3PW12O40/TiO2复合型光催化剂,并运用XRD、SEM、FT-IR和DRS对催化剂进行表征和分析.研究了可见光光照下H3PW12O40/TiO2对孔雀石绿降解的光催化活性,考察了浸渍量、催化剂用量、底物浓度、pH值对光催化降解率的影响.实验表明,在pH=5条件下,H3PW12O40/TiO2催化剂用量为0.3g.L-1,浓度为10mg·mL-1的孔雀石绿溶液在2L·min-1曝气、300W可见光下光照4h后光催化降解率为78%,比TiO2光催化活性提高了24%.     

上转光剂掺杂新型纳米TiO2催化剂的制备及利用可见光降解反应艳蓝KN-R染料的研究

合成了一种新型含有稀土金属Er的上转光剂,40CdF2·60BaF2·0.8Er2O3,此上转光剂在488 nm可见光的激发下,产生了5个波长均小于387 nm的上转换紫外发射峰.采用超声波分散的方法制备出了上转光剂掺杂的纳米TiO2可见光光催化剂.采用X射线衍射(XRD)及透射电镜(TEM)对催化剂进行了表征.以反应艳蓝KN-R为研究对象,研究了在(三基色灯下发出的)可见光的照射下该可见光光催化剂的催化降解性能,并与未掺杂纳米TiO2粉末的催化剂性能进行了对比.实验结果表明,作为掺杂成分的上转光剂可有效地将可见光转化为紫外光并被纳米TiO2粉末吸收利用,在可见光照射50 h后反应艳蓝KN-R降解率达74.36%,大大高于未掺杂纳米TiO2的降解率(23.10%).     

Ag/TiO2光催化降解磺基水杨酸的研究

采用光化学沉积法制备了Ag/TiO2 光催化剂 ,并对典型难生物降解的有机污染物磺基水杨酸进行了光催化降解研究。结果表明 ,1 0 %担载量的Ag能显著提高TiO2 光催化活性 ,可在较短时间内实现对磺基水杨酸较高的降解效率。     

碳纳米管负载TiO2对1,2,4-三氯苯的光降解研究

碳纳米管负载TiO2复合光催化剂与纳米TiO2光催化剂对1,2,4-三氯苯的光催化降解效果,及降解动力学的研究结果表明,复合光催化剂比纳米TiO2有更好的光催化降解效果,经254 nm紫外光辐照60 min后,使用复合光催化剂的1,2,4-三氯苯降解了70%,而使用纳米TiO2为催化剂的1,2,4-三氯苯仅降解了51%...     

Photocatalytic degradation of Acid Blue 62 over CuO-SnO2 nanocomposite photocatalyst under simulated sunlight

The novel CuO-SnO2 nanocomposite oxide photocatalysts were prepared by simple co-precipitation method, and characterized by X- ray diffraction, transmission electron microscopy, N2 adsorption-desorption measurement and UV-Vis diffuse reflectance spectroscopy. The photocatalytic activities of CuO-SnO2, evaluated using the photodegradation of Acid Blue 62 as a probe reaction under the irradiation of Xenon light, were also found to be related to the calcination temperature and the molar ratio of Cu to Sn. The maximum photocatalytic activity of the CuO-SnO2 photocatalyst was observed to be calcined at 500~C for 3 h （the molar ratio of Cu to Sn was 1：1） due to the sample with good crystallization and high surface area. It also showed much higher photocatalytic activity in treatment dye wastewater under simulated sunlight irradiation compared to Degussa P25 TiO2.     

低温燃烧合成纳米Ni掺杂TiO2光催化剂的表征及活性研究

采用低温燃烧合成法制备了Ni掺杂TiO₂光催化剂,通过紫外-可见漫反射光谱(UV-Vis DRS)、X射线粉末衍射(XRD)、激光散射、热重-差示扫描量热分析(TG-DSC)等方法对催化剂的光吸收特性、晶相组成、粒度分布、升温过程中化学变化等进行了表征,以亚甲基蓝为模型污染物考察了催化剂在可见光下的光催化活性.结果表明,相对P25而言,Ni掺杂TiO₂的光吸收带边红移,当Ni/Ti原子比为0.4时,催化剂的带隙宽度为2.3eV,对应的吸收带边为564nm;催化剂晶型以锐钛矿TiO₂为主,随Ni掺杂量增大,NiTiO₃比例升高;催化剂粒径主要分布在50～150nm之间,占总量的96.9%;升温过程中催化剂在445.2℃发生晶型转化,出现锐钛矿和NiTiO₃晶体.催化剂显示出较高的催化活性,在可见光作用150min后最高可使93.9%的亚甲基蓝分解,活性高于P25.     

负载型纳米TiO2/AC对偶氮染料的光催化降解研究

以钛酸四丁酯和粒状活性炭(AC)为主要原料,采用溶胶-凝胶-浸渍法制备出负载型纳米TiO2/AC催化剂.在流化床反应器中分别对2种典型的偶氮类染料橙黄G、活性艳红X-3B模拟废水进行了光催化降解研究,探讨了pH值、外加氧化剂对光催化降解率的影响,并对催化剂进行了回收再生利用试验.结果表明,TiO2/AC催化剂具有良好的光催化活性、吸附特性及可再生性,60 min后对2种染料反应的光催化降解率分别可达到99.71%和97 12%,反应180 min后的TOC去除率分别达到81.54%和81.99%;反应后TiO2/AC催化剂回收率大于95%,经焙烧再生后对橙黄G反应60 min的光催化降解率仍高达95.93%.     

磁性微球负载光催化剂制备及处理造纸废水研究

采用溶胶-凝胶法,在磁性颗粒表面包覆TiO2,制备了易于固液分离的磁载光催化剂TiO2/SiO2/Fe3O4,通过XRD和TEM对产物的晶体结构、晶粒大小、形貌进行了表征,讨论了焙烧温度、焙烧时间、催化剂用量和光照时间等对TiO2光催化剂处理造纸废水的影响。结果表明:焙烧温度为500℃、焙烧时间3.5h时,光催化活性最高;催化剂用量为2.5g/L,光照时间4h时TiO2降解造纸废水的能力最强。     

锐态型纳米TiO_2光催化处理含镉废水的研究

采用溶胶-凝胶法制备锐态型纳米TiO2,用XRD、SEM对粉体进行表征。在紫外光的作用下将自制纳米TiO2光催化处理废水中的Cd2+。考察反应时间、pH值、废水负荷、催化剂用量等因素对去除率的影响。实验结果表明:纳米TiO2光催化处理含镉废水的去除率高,含镉废水pH值、废水负荷、纳米二氧化钛浓度以及反应时间等因素影响含镉废水去除率。在优化的处理条件中:废水镉浓度为30mg/L,纳米TiO2投加量为3mg/L,含镉废水的pH为10,反应时间为2.5h,废水中镉的去除率可达99.52%。     

Photocatalytic degradation of L-acid by TiO2 supported on the activated carbon

Introduction Aromatic sulfonic acid, which is produced in large amounts in chemical industry since the end of 19th century, has been widely applied in many industrial processes, including the various steps of procedure (Alonso and Barcelo, 2000). Naphthalene- sulfonic acids are of importance as dye intermediates and commonly used in the textile auxiliary industry employing many azo dyes and pigments. Among them, 1-naphthol-5-sulphonic acid (L-acid) is widely used in the printing as the raw ma…