Investigation of surfactant-enhanced mass removal and flux reduction in 3D correlated permeability fields using magnetic resonance imaging

Magnetic resonance imaging (MRI) was used to visualize the NAPL source zone architecture before and after surfactant-enhanced NAPL dissolution in three-dimensional (3D) heterogeneously packed flowcells characterized by different longitudinal correlation lengths: 2.1 cm (aquifer 1) and 1.1 cm (aquifer 2). Surfactant flowpaths were determined by imaging the breakthrough of a paramagnetic tracer (MnCl(2)) analyzed by the method of moments. In both experimental aquifers, preferential flow occurred in high permeability materials with low NAPL saturations, and NAPL was preferentially removed from the top of the aquifers with low saturation. Alternate flushing with water and two surfactant pulses (5-6 pore volumes each) resulted in approximately 63% of NAPL mass removal from both aquifers. However, overall reduction in mass flux (Mass Flux 1) exiting the flowcell was lower in aquifer 2 (68%) than in aquifer 1 (81%), and local effluent concentrations were found to increase by as high as 120 times at local sampling ports from aquifer 2 after surfactant flushing. 3D MRI images of NAPL revealed that NAPL migrated downward and created additional NAPL source zones in previously uncontaminated areas at the bottom of the aquifers. The additional NAPL source zones were created in the direction transverse to flow in aquifer 2, which explains the higher mass flux relative to aquifer 1. Analysis using a total trapping number indicates that mobilization of NAPL trapped in the two coarsest sand fractions is possible when saturation is below 0.5 and 0.4, respectively. Results from this study highlight the potential impacts of porous media heterogeneity and NAPL source zone architecture on advanced in-situ flushing technologies.     

Effect of nonionic surfactant partitioning on the dissolution kinetics of residual perchloroethylene in a model porous medium

At concentrations above the critical micelle concentration, surfactants can significantly enhance the solubilization of residual nonaqueous phase liquids (NAPL) and, for this reason, are the focus of research on surfactant-enhanced aquifer remediation (SEAR). As a consequence of their amphiphilic nature, surfactants may also partition to various extents between the organic and aqueous phases, thereby affecting SEAR performance. We report here on the observation and analysis of the effect of surfactant partitioning on the dissolution kinetics of residual perchloroethylene (PCE) by aqueous solutions (1000 mg/L) of the non-ionic surfactant Triton X-100 in a model porous medium. For this fluid system, batch equilibration experiments showed that the surfactant partitions strongly into the NAPL (NAPL-water partition coefficient equal to 12.5). Dynamic interfacial tension (IFT) measurements were employed to study surfactant diffusion and interfacial adsorption. The dynamic IFT measurements were consistent with partitioning of the surfactant between the two liquid phases. PCE dissolution experiments, conducted in a transparent glass micromodel using an aqueous surfactant solution, were contrasted to experiments using clean water. Surfactant partitioning was observed to delay significantly the onset of micellar solubilization of PCE, an observation reproduced by a numerical model. This effect is attributed to the reduction of surfactant concentration in the immediate vicinity of the NAPL-water interface, which accompanies transport of the surfactant into the NAPL. Accordingly, it is suggested that both the rate and the extent of diffusion of the surfactant into the NAPL affect the onset of and the driving force for micellar solubilization. While many surfactants do not readily partition in NAPL, this possibility must be considered when selecting non-ionic surfactants for the enhanced solubilization of residual chlorinated solvents in porous media.     

Surfactant enhanced recovery of tetrachloroethylene from a porous medium containing low permeability lenses. 1. Experimental studies

A matrix of batch, column and two-dimensional (2-D) box experiments was conducted to investigate the coupled effects of rate-limited solubilization and layering on the entrapment and subsequent recovery of a representative dense NAPL, tetrachloroethylene (PCE), during surfactant flushing. Batch experiments were performed to determine the equilibrium solubilization capacity of the surfactant, polyoxyethylene (20) sorbitan monooleate (Tween 80), and to measure fluid viscosity, density and interfacial tension. Results of one-dimensional column studies indicated that micellar solubilization of residual PCE was rate-limited at Darcy velocities ranging from 0.8 to 8.2 cm/h and during periods of flow interruption. Effluent concentration data were used to develop effective mass transfer coefficient (Ke) expressions that were dependent upon the Darcy velocity and duration of flow interruption. To simulate subsurface heterogeneity, 2-D boxes were packed with layers of F-70 Ottawa sand and Wurtsmith aquifer material within 20-30 mesh Ottawa sand. A 4% Tween 80 solution was then flushed through PCE-contaminated boxes at several flow velocities, with periods of flow interruption. Effluent concentration data and visual observations indicated that both rate-limited solubilization and pooling of PCE above the fine layers reduced PCE recovery to levels below those anticipated from batch and column measurements. These experimental results demonstrate the potential impact of both mass transfer limitations and subsurface layering on the recovery of PCE during surfactant enhanced aquifer remediation.     

Effects of ethanol addition on micellar solubilization and plume migration during surfactant enhanced recovery of tetrachloroethene

Alcohol addition has been suggested for use in combination with surfactant flushing to enhance solubilization kinetics and permit density control of dense non-aqueous phase liquid (DNAPL)-laden surfactant plumes. This study examined the effects of adding ethanol (EtOH) to a 4% Tween 80 (polyoxyethylene (20) sorbitan monooleate) solution used to flush tetrachloroethene (PCE)-contaminated porous media. The influence of EtOH concentration, subsurface layering and scale on flushing solution delivery and PCE recovery was investigated through a combination of experimental and mathematical modeling studies. Results of batch experiments demonstrated that the addition of 2.5%, 5% and 10% (wt.) EtOH incrementally increased the PCE solubilization capacity and viscosity of the surfactant solution, while reducing solution density from 1.002 to 0.986 g/cm3. Effluent concentration data obtained from one-dimensional (1-D) column experiments were used to characterize rate-limited micellar solubilization of residual PCE, which was strongly dependent upon flow velocity and weakly dependent upon EtOH concentration. Two-dimensional (2-D) box studies illustrated that minor differences (0.008 g/cm3) between flushing and resident solution density can strongly influence surfactant front propagation. A two-dimensional multiphase simulator, MISER, was used to model the influence of EtOH composition on the aqueous flow field and PCE mass recovery. The ability of the numerical simulator to predict effluent concentrations and front propagation was demonstrated for both 1-D columns and 2-D boxes flushed with EtOH-amended Tween 80 solutions. Results of this study quantify the potential influence of alcohol addition on surfactant solution properties and solubilization capacity, and demonstrate the importance of considering small density variations in remedial design.     

Surfactant enhanced recovery of tetrachloroethylene from a porous medium containing low permeability lenses. 2. Numerical simulation

A numerical model of surfactant enhanced solubilization was developed and applied to the simulation of nonaqueous phase liquid recovery in two-dimensional heterogeneous laboratory sand tank systems. Model parameters were derived from independent, small-scale, batch and column experiments. These parameters included viscosity, density, solubilization capacity, surfactant sorption, interfacial tension, permeability, capillary retention functions, and interphase mass transfer correlations. Model predictive capability was assessed for the evaluation of the micellar solubilization of tetrachloroethylene (PCE) in the two-dimensional systems. Predicted effluent concentrations and mass recovery agreed reasonably well with measured values. Accurate prediction of enhanced solubilization behavior in the sand tanks was found to require the incorporation of pore-scale, system-dependent, interphase mass transfer limitations, including an explicit representation of specific interfacial contact area. Predicted effluent concentrations and mass recovery were also found to depend strongly upon the initial NAPL entrapment configuration. Numerical results collectively indicate that enhanced solubilization processes in heterogeneous, laboratory sand tank systems can be successfully simulated using independently measured soil parameters and column-measured mass transfer coefficients, provided that permeability and NAPL distributions are accurately known. This implies that the accuracy of model predictions at the field scale will be constrained by our ability to quantify soil heterogeneity and NAPL distribution.     

Investigation of surfactant-enhanced dissolution of entrapped nonaqueous phase liquid chemicals in a two-dimensional groundwater flow field.

Because of their low solubility, waste chemicals in the form of nonaqueous phase liquids (NAPLs) that are entrapped in subsurface formations act as long-term sources of groundwater contamination. In the design of remediation schemes that use surfactants, it is necessary to estimate the mass transfer rate coefficients under multi-dimensional flow fields that exit at field sites. In this study, we investigate mass transfer under a two-dimensional flow field to obtain an understanding of the basic mechanisms of surfactant-enhanced dissolution and to quantify the mass transfer rates. Enhanced dissolution experiments in a two-dimensional test cell were conducted to measure rates of mass depletion from entrapped NAPLs to a flowing aqueous phase containing a surfactant. In situ measurement of transient saturation changes using a gamma attenuation system revealed dissolution patterns that are affected by the dimensionality of the groundwater flow field. Numerical modeling of local flow fields that changed with time, due to depletion of NAPL sources, enabled the examination of the basic mechanisms of NAPL dissolution in complex groundwater systems. Through nonlinear regression analysis, mass transfer rates were correlated to porous media properties, NAPL saturation and aqueous phase velocity. Results from the experiments and numerical analyses were used to identify deficiencies in existing methods of analysis that uses assumptions of one-dimensional flow, homogeneity of aquifer properties, local equilibrium and idealized transient mass transfer.     

Three-fluid retention in porous media involving water, PCE and air

A classical way to obtain three-fluid retention curves in porous media from measured two-fluid retention curves is based on the Leverett concept, which states that the total volumetric liquid content in a water-wet porous medium, containing water, a nonaqueous-phase liquid (NAPL) and air, is a function of the capillary pressure across the interface between the continuous NAPL and air. This functional relationship results from the assumed condition that in a three-fluid porous medium, the intermediate wetting fluid spreads over the water-air interface. Application of Leverett's concept may not be valid, however, for nonspreading NAPLs like perchloroethylene (PCE). This paper discusses measurements of both PCE-air and water-PCE-air retention curves using a long vertical column in conjunction with a dual-energy gamma radiation system. The data indicate that the Leverett concept was applicable only until a critical PCE saturation had been reached.     

Infiltration and redistribution of perchloroethylene in partially saturated, stratified porous media

Contamination of the subsurface by nonaqueous phase liquids (NAPLs) is a widespread problem. To investigate the behavior of a nonspreading, dense NAPL (DNAPL) in the vadose zone, we conducted perchloroethylene (PCE) infiltration experiments in nominally 1- and 2-dimensional (D), stratified porous media. In addition, the usefulness and limitations of a multifluid flow simulator to describe PCE infiltration and redistribution under the experimental conditions were tested. The physical simulations were conducted in a column (1-D) and a flow container (2-D) which were packed with two distinct layers of coarse-grained sand and a fine-grained sand layer in between. Volumetric water and PCE contents were determined with a fully automated dual-energy gamma radiation system. While migrating through the drier parts of the coarse-grained sand layers, PCE appeared to wet the water–air interface rather than displacing any water. In the wetter parts of the porous medium, PCE displaced water and behaved as a true nonwetting fluid. PCE showed a limited response to gradients in capillary pressure and rather high values for the volumetric PCE content were measured in the fine-grained sand layers. This was attributed to the nonspreading nature of PCE. The multifluid flow simulator appeared to predict the initial PCE movement in the vadose zone reasonably well. However, the model was not capable of predicting the final amounts of PCE retained in either the unsaturated or saturated part of the flow domain, mainly because the simulator does not consider the nonspreading flow behavior of NAPLs.     

Three-dimensional visualization and quantification of non-aqueous phase liquid volumes in natural porous media using a medical X-ray Computed Tomography scanner

This study demonstrates the capabilities of a typical medical X-ray Computed Tomography (CT) scanner to non-destructively quantify non-aqueous phase liquid (NAPL) volumes, saturation levels, and three-dimensional spatial distributions in packed soil columns. Columns packed with homogeneous sand, heterogeneous sand, or natural soil, were saturated with water and injected with known quantities of gasoline or tetrachloroethene and scanned. A methodology based on image subtraction was implemented for computing soil porosity and NAPL volumes in each 0.35 mm x 0.35 mm x 1 mm voxel of the columns. Elimination of sample positioning errors and instrument drift artifacts was essential for obtaining reliable estimates of above parameters. The CT data-derived total NAPL volume was in agreement with the measured NAPL volumes injected into the columns. CT data-derived NAPL volume is subject to a 2.6% error for PCE and a 15.5% error for gasoline, at average NAPL saturations as low as 5%, and is mainly due to instrument noise. Non-uniform distributions of NAPL due to preferential flow, and accumulation of NAPL above finer-grained layers could be observed from the data on 3-D distributions of NAPL volume fractions.     

Refinement of the density-modified displacement method for efficient treatment of tetrachloroethene source zones

A novel method to remediate dense nonaqueous phase liquid (DNAPL) source zones that incorporates in situ density conversion of DNAPL via alcohol partitioning followed by displacement with a low interfacial tension (IFT) surfactant flood has been developed. Previous studies demonstrated the ability of the density-modified displacement (DMD) method to recover chlorobenzene (CB) and trichloroethene (TCE) from heterogeneous porous media without downward migration of the dissolved plume or free product. However, the extent of alcohol (n-butanol) partitioning required for in situ density conversion of high-density NAPLs, such as tetrachloroethene (PCE), could limit the utility of the DMD method. Hence, the objective of this study was to compare the efficacy of two n-butanol delivery approaches: an aqueous solution of 6% (wt) n-butanol and a surfactant-stabilized macroemulsion containing 15% (vol) n-butanol in water, to achieve density reduction of PCE-NAPL in two-dimensional (2-D) aquifer cells. Results of liquid-liquid equilibrium studies indicated that density conversion of PCE relative to water occurred at an n-butanol mole fraction of 0.56, equivalent to approximately 5 ml n-butanol per 1 ml of PCE when in equilibrium with an aqueous solution. In 2-D aquifer cell studies, density conversion of PCE was realized using both n-butanol preflood solutions, with effluent NAPL samples exhibiting density reductions ranging from 0.51 to 0.70 g/ml. Although the overall PCE mass recoveries were similar (91% and 93%) regardless of the n-butanol delivery method, the surfactant-stabilized macroemulsion preflood removed approximately 50% of the PCE mass. In addition, only 1.2 pore volumes of the macroemulsion solution were required to achieve in situ density conversion of PCE, compared to 6.4 pore volumes of the 6% (wt) n-butanol solution. These findings demonstrate that use of the DMD method with a surfactant-stabilized macroemulsion containing n-butanol holds promise as an effective source zone remediation technology, allowing for efficient recovery of PCE-DNAPL while mitigating downward migration of the dissolved plume and free product.     

Manipulation of density and viscosity for the optimization of DNAPL recovery by alcohol flooding

Laboratory experiments demonstrate that in situ recovery of pooled tetrachloroethene (PCE) from porous media may be accomplished more efficiently using multiple-step alcohol floods than with single alcohol floods. To optimize flooding efficiency while maintaining a low risk of downward DNAPL mobilization, a three-step flooding process is developed employing an isobutanol preflood, a composite alcohol mainflood, and a polymer solution postflood. The density and viscosity of these solutions are manipulated to prevent the onset and propagation of viscous and gravitational fingers, while maintaining phase behavior critical for efficient miscible NAPL displacement. An aqueous partitioning preflood solution of 10% by volume (10% v) isobutanol reduces the NAPL density in situ to approximately 1.00 g/ml by swelling the NAPL prior to miscible displacement induced by the mainflood. The composite alcohol mainflood, containing 65% v ethylene glycol and 35% v 1-propanol maintains miscibility while achieving neutral buoyancy and near stable displacement of the NAPL. Aqueous solutions of xanthan gum polymer efficiently displace the mainflood, reducing viscous fingering associated with waterfloods. Two-dimensional experiments using the multiple-step technique achieve 99.8% DNAPL mass recovery using a total of 0.45 pore volumes of alcohol, illustrating greater recovery efficiency than previous alcohol flooding formulations under comparable conditions.     

Influence of residual surfactants on DNAPL characterization using partitioning tracers

The partitioning tracer technique is among the DNAPL source-zone characterization methods being evaluated, while surfactant in-situ flushing is receiving attention as an innovative technology for enhanced source-zone cleanup. Here, we examine in batch and column experiments the magnitude of artifacts introduced in estimating DNAPL content when residual surfactants are present. The batch equilibrium tests, using residual surfactants ranging from 0.05 to 0.5 wt.%, showed that as the surfactant concentrations increased, the tracer partition coefficients decreased linearly for sodium hexadecyl diphenyl oxide disulfonate (DowFax 8390), increased linearly for polyoxyethylene (10) oleyl ether (Brij 97), and decreased slightly or exhibited no observable trend for sodium dihexyl sulfosuccinate (AMA 80). Results from column tests using clean sand with residual DowFax 8390 and Tetrachloroethylene (PCE) were consistent with those of batch tests. In the presence of DowFax 8390 (less than 0.5 wt.%), the PCE saturations were underestimated by up to 20%. Adsorbed surfactants on a loamy sand with positively charged oxides showed false indications of PCE saturation based on partitioning tracers in the absence of PCE. Using no surfactant (background soil) gave a false PCE saturation of 0.0004, while soil contacted by AMA 80, Brij 97, and DowFax 8390 gave false PCE saturations of 0.0024, 0.043, and 0.23, respectively.     

Biosurfactant-enhanced solubilization of NAPL mixtures

Remediation of nonaqueous phase liquids (NAPLs) by conventional pump-and-treat methods (i.e., water flushing) is generally considered to be ineffective due to low water solubilities of NAPLs and to mass-transfer constraints. Chemical flushing techniques, such as surfactant flushing, can greatly improve NAPL remediation primarily by increasing the apparent solubility of NAPL contaminants. NAPLs at hazardous waste sites are often complex mixtures. However, the equilibrium and nonequilibrium mass-transfer characteristics between NAPL mixtures and aqueous surfactant solutions are not well understood. This research investigates the equilibrium solubilization behavior of two- and three-component NAPL mixtures (containing akylbenzenes) in biosurfactant solutions. NAPL solubilization is found to be ideal in water (i.e., obeys Raoult's Law), while solubilization in biosurfactant solutions was observed to be nonideal. Specifically, the relatively hydrophobic compounds in the mixture experienced solubility enhancements that were greater than those predicted by ideal enhanced solubilization theory, while the solubility enhancements for the relatively hydrophilic compounds were less than predicted. The degree of nonideality is shown to be a nonlinear function of the NAPL-phase mole fraction. Empirical relationships based on the NAPL-phase mole fraction and/or micelle-aqueous partition coefficients measured in single-component NAPL systems are developed to estimate values for the multicomponent partition coefficients. Empirical relationships that incorporate both the NAPL-phase mole fraction and single-component partition coefficients yield much improved estimates for the multicomponent partition coefficient.     

Reaction-enhanced mass transfer and transport from non-aqueous phase liquid source zones

The objective of the following research is to theoretically quantify the enhancement of interphase mass transfer of dissolved non-aqueous phase liquid (NAPL) compounds from the non-aqueous phase to the aqueous phase and the enhancement of dispersive mass transport from a NAPL zone due to destruction of dissolved NAPL compounds. For relatively slow reaction rates, such as for permanganate and perchloroethene (PCE), local-scale mass transfer enhancement is expected to be small. Dispersive mass transport with reaction from a horizontal NAPL zone can be quantified using equations derived for a mathematically equivalent falling film reactor system. In contrast to local-scale interphase mass transfer, dispersive mass transport from NAPL zones may be significantly increased by reaction. Enhancement factors due to destruction of the NAPL compound(s) are mainly dependent on NAPL solubility and oxidant concentration and to a lesser extent on reaction rate, stoichiometry, and transverse dispersion coefficients. Higher NAPL solubility and/or lower oxidant concentration reduces the maximum expected enhancement factor. Reaction enhancement factors for mass transport from NAPL zones are expected to be in the range of 5-50 for permanganate and chlorinated solvents. Theoretical results suggest that assuming instantaneous reaction rates may be appropriate for dispersive mass transport from NAPL zones.     

Laboratory-scale in situ chemical oxidation of a perchloroethylene pool using permanganate

In situ chemical oxidation (ISCO) is an emerging technology for the destruction of some chlorinated solvents present in subsurface environments. A laboratory investigation using a physical model was designed to assess the effectiveness of using permanganate as an oxidant to reduce the mass of a perchloroethylene (PCE) pool. The physical model was filled with silica sand overlying a silica flour base, simulating a two-dimensional saturated sand zone overlying a capillary barrier. PCE was introduced into the model so that it rested on top of the silica flour base, forming a dense nonaqueous phase liquid pool. The experimental methodology involved flushing the model with a permanganate solution for 146 days. During this period, measurements of chloride were used to assess the extent of pool oxidation. Before and after the oxidant flush, the quasi-steady state dissolution from the PCE pool was evaluated. Additionally, tracer studies were completed to assess changes in the flow field due to the oxidation process. At the termination of the experiment nine soil cores extracted from the model were used to detect the presence of MnO2 deposits and to quantify the mass of PCE remaining in the system. Excavation of the remaining material in the model revealed that the MnO2 distribution throughout the model was consistent with that observed in the cores. The oxidant flush was concluded before all of the pure phase PCE had been completely oxidized; however, approximately 45% of the PCE mass was removed, resulting in a fourfold decrease in the quasi-steady state aqueous phase mass loading of PCE from the pool. Measurements of chloride during the oxidant flush and of PCE in the soil cores suggested that the oxidation reaction occurred primarily at the upgradient edge of the PCE pool. MnO2 deposits within the model aquifer decreased the velocity of water directly above the pool, and the overall mass transfer from the remaining PCE pool. The results of this experimental study indicate that ISCO using permanganate is capable of removing substantial mass from a DNAPL pool; however, the performance of ISCO as a pool removal technology will be limited by the formation and precipitation of hydrous MnO2 that occurs during the oxidation process.     

Field demonstration of surfactant-enhanced solubilization of DNAPL at Dover Air Force Base, Delaware

This study reports on a surfactant-based flood for tetrachloroethylene (PCE) removal from a control test cell at the Dover National Test Site. The surfactant formulation (sodium dihexyl sulfosuccinate (Aerosol-MA or AMA), isopropanol and calcium chloride) was able to achieve a high concentration of PCE in swollen micelles (supersolubilization) without vertical PCE migration. The hydraulic system included eight screened wells that were operated in both vertical circulation and line drive configurations. After 10 pore volumes of flushing, the overall PCE removal was 68% (65% of which corresponded to the surfactant flooding alone). In addition, the residual PCE saturation was reduced from 0.7% to 0.2%, and the concentration of PCE in the groundwater was reduced from 37-190 mg/L before the flushing to 7.3 mg/L after flooding. Recycling the surfactant solution reduced the required surfactant mass (and thus cost, and waste) by 90%. Close to 80% of the total PCE removal was obtained during the first five pore volumes which were operated in an upward vertical circulation flow scheme. No free oil phase was observed during the test. Further analysis of multilevel sampler data suggests that most of the trapped oil remaining in the cell was likely localized in secluded regions of the aquifer, which helps explain the lower PCE groundwater concentration after remedial activities. In summary, this field study demonstrated the feasibility of surfactant-enhanced remediation to reduce the mass in the source zone and significantly reduce the PCE aqueous concentration and therefore the risk associated with the contaminant plume.     

The significance of heterogeneity on mass flux from DNAPL source zones: an experimental investigation

Understanding the process of mass transfer from source zones of aquifers contaminated with organic chemicals in the form of dense non-aqueous phase liquids (DNAPL) is of importance in site management and remediation. A series of intermediate-scale tank experiments was conducted to examine the influence of aquifer heterogeneity on DNAPL mass transfer contributing to dissolved mass emission from source zone into groundwater under natural flow before and after remediation. A Tetrachloroethylene (PCE) spill was performed into six source zone models of increasing heterogeneity, and both the spatial distribution of the dissolution behavior and the net effluent mass flux were examined. Experimentally created initial PCE entrapment architecture resulting from the PCE migration was largely influenced by the coarser sand lenses and the PCE occupied between 30 and 60% of the model aquifer depth. The presence of DNAPL had no apparent effect on the bulk hydraulic conductivity of the porous media. Up to 71% of PCE mass in each of the tested source zone was removed during a series of surfactant flushes, with associated induced PCE mobilization responsible for increasing vertical DNAPL distributions. Effluent mass flux due to water dissolution was also found to increase progressively due to the increase in NAPL-water contact area even though the PCE mass was reduced. Doubling of local groundwater flow velocities showed negligible rate-limited effects at the scale of these experiments. Thus, mass transfer behavior was directly controlled by the morphology of DNAPL within each source zone. Effluent mass flux values were normalized by the up-gradient DNAPL distributions. For the suite of aquifer heterogeneities and all remedial stages, normalized flux values fell within a narrow band with mean of 0.39 and showed insensitivity to average source zone saturations.     

Co-surfactant of ethoxylated sorbitan ester and sorbitan monooleate for enhanced flushing of tetrachloroethylene

This work evaluated the flushing efficiency of tetrachloroethylene (PCE) using the co-surfactant of non-ionic ethoxylated sorbitan ester (Tween) and oilphilic sorbitan monooleate (Span 80), which formed more hydrophobic micelles than Tween alone. The flushing efficiency was evaluated with laboratory columns filled with silica and aquifer sand. Results from column flushing were also compared to those of batch solubility experiments to study the removal mechanism by the co-surfactant solution. Compared to Tween 80 alone, the molar solubilization ratio and the affinity between the micelles and PCE increased 84% and 90%, respectively, by the co-surfactant solution of Tween 80 and Span 80 mixed at a 4:1 ratio. Flushing with 1% Tween 80 solution yielded a steady PCE recovery of 7% for both silica and aquifer sand in each pore volume (PV). Flushing with co-surfactant of 1% Tween 80 + Span 80 (4:1) further increased PCE recovery to 10% for silica sand and 13% for aquifer sand per PV. A comparison of results from column flushing and batch solubility tests indicated that the primary flushing mechanism of PCE using the co-surfactant solution of Tween 80 + Span 80 (4:1) was micellar solubilization.     

Mass flux from a non-aqueous phase liquid pool considering spontaneous expansion of a discontinuous gas phase

The partitioning of non-aqueous phase liquid (NAPL) compounds to a discontinuous gas phase results in the repeated spontaneous expansion, snap-off, and vertical mobilization of the gas phase. This mechanism has the potential to significantly affect the mass transfer processes that control the dissolution of NAPL pools by increasing the vertical transport of NAPL mass and increasing the total mass transfer rate from the surface of the pool. The extent to which this mechanism affects mass transfer from a NAPL pool depends on the rate of expansion and the mass of NAPL compound in the gas phase. This study used well-controlled bench-scale experiments under no-flow conditions to quantify for the first time the expansion of a discontinuous gas phase in the presence of NAPL. Air bubbles placed in glass vials containing NAPL increased significantly in volume, from a radius of 1.0 mm to 2.0 mm over 215 days in the presence of tetrachloroethene (PCE), and from a radius of 1.2 mm to 2.3 mm over 22 days in the presence of trans-1,2-dichloroethene (tDCE). A one-dimensional mass transfer model, fit to the experimental data, showed that this expansion could result in a mass flux from the NAPL pool that was similar in magnitude to the mass flux expected for the dissolution of a NAPL pool in a two-fluid (NAPL and water) system. Conditions favouring the significant effect of a discontinuous gas phase on mass transfer were identified as groundwater velocities less than ~0.01 m/day, and a gas phase that covers greater than ~10% of the pool surface area and is located within ~0.01 m of the pool surface. Under these conditions the mass transfer via a discontinuous gas phase is expected to affect, for example, efforts to locate NAPL source zones using aqueous concentration data, and predict the lifetime and risk associated with NAPL source zones in a way that is not currently included in the common conceptual models used to assess NAPL-contaminated sites.     

A micromodel analysis of factors influencing NAPL removal by surfactant foam flooding

A methodology to study the trichloroethylene (TCE) and dodecane removal in porous media by surfactant foams (SF) was presented by using etched-glass micromodels. The purpose of this work was to systematically evaluate the impact of various physicochemical factors such as gas fraction (GF), surfactant concentration, pore structure and nonaqueous phase liquid (NAPL) types on NAPL removal during SF flooding. The TCE displacement by SF was dependent on the gas fraction of SF. Low GFs (50% and 66%) were more efficient for TCE removal and sweep efficiencies than a high GF (85%). An increase in TCE removal was observed with increasing surfactant concentration at a fixed GF. TCE removal by SF flooding appeared to be dependent more to the value of Capillary number rather than to the concentration of surfactant solution. The effect of the pore heterogeneity was evaluated by employing two different types of micromodels. The Capillary number is an important parameter in the determination of sweep efficiency or gas saturation of SF in a nonhomogeneous porous medium. However, the TCE removal from a nonhomogeneous porous medium may not be associated with sweep efficiency. The initial configuration of residual TCE blobs in a nonhomogeneous porous medium would also be influential in displacing TCE. Sweep efficiencies and pressure responses of two NAPL systems (TCE and dodecane) were monitored to evaluate foam stability when the foam contacts the NAPLs. Stable foam contacting with TCE is implied, while it appears that dodecane cause the SF to collapse. All results indicate that the Capillary number (a ratio of viscous forces to capillary forces) is the most important parameter for TCE removal by SF flooding. Micromodel visualizations of water, surfactant and SF floods were showed and also discussed.