Feasibility study on high-temperature sorption of hydrogen sulfide by natural soils

In this study, seven natural soils were tested for the sorption of hydrogen sulfide from coal gasification gas at high temperature. Results indicate that the LP natural soil has the best performance and the highest sulfur sorption capacity. After extracting free iron oxides, most natural soils have no sorption efficiency. The free iron oxides, therefore, proved to be the major components that react with hydrogen sulfide to form iron sulfides. The sulfur sorption capacity, either determined by EA or breakthrough time, is very close to the theoretical value based on the stoichiometric calculation with the content of free iron oxides. Moreover, the presence of CO is a positive effect while H2 is a negative effect. This can be explained via the water-shift reaction. On the basis of the results of temperature-programmed sulfidation (TPS), the starting temperature for the sorption of hydrogen sulfide is between 623-673 K. From the analyses of temperature-programmed oxidation (TPO) and XPS, the iron polysulfides are the major products and approximately 90% regeneration efficiency can be theoretically achieved while the temperature is controlled higher than 813 K. In the regeneration tests, the results show that the LP natural soil can be regenerated and thus reused after the oxidation process. No significant degeneration occurs on the LP natural soil after five sorption/regeneration cycles. The sulfur sorption capacity of the tenth regenerated soil can be achieved at least 80% compared to the fresh one. The experimental analyzed SO2 concentration from the regeneration process is almost identical to the theoretical calculated equilibrium concentration of the process. Maghemite is the main product after the regeneration process.     

Microwave regeneration of activated carbon used for removal of solvents from vented air

A microwave regeneration of activated carbon used to remove organic solvents from vented air has been investigated. Methyl ethyl ketone (MEK), acetone, and tetrachloroethylene (TCE) vapors were removed from vented air through adsorption onto granular activated carbon. The saturated carbon was then regenerated in a microwave field, where the solvent was quickly desorbed and recovered from the inner pores of the carbon granules. The microwave-induced regeneration restored the original adsorption capacity and surface area of the activated carbon.     

Microwave Regeneration of Activated Carbon Used for Removal of Solvents from Vented Air

ABSTRACT

A microwave regeneration of activated carbon used to remove organic solvents from vented air has been investigated. Methyl ethyl ketone (MEK), acetone, and tetrachloroethylene (TCE) vapors were removed from vented air through adsorption onto granular activated carbon. The saturated carbon was then regenerated in a microwave field, where the solvent was quickly desorbed and recovered from the inner pores of the carbon granules. The microwave-induced regeneration restored the original adsorption capacity and surface area of the activated carbon.     

Production of activated carbons from pyrolysis of waste tires impregnated with potassium hydroxide

Activated carbons were produced from waste tires using a chemical activation method. The carbon production process consisted of potassium hydroxide (KOH) impregnation followed by pyrolysis in N2 at 600-900 degrees C for 0-2 hr. The activation method can produce carbons with a surface area (SA) and total pore volume as high as 470 m2/g and 0.57 cm3/g, respectively. The influence of different parameters during chemical activation, such as pyrolysis temperature, holding time, and KOH/tire ratio, on the carbon yield and the surface characteristics was explored, and the optimum preparation conditions were recommended. The pore volume of the resulting carbons generally increases with the extent of carbon gasified by KOH and its derivatives, whereas the SA increases with degree of gasification to reach a maximum value, and then decreases upon further gasification.     

微波辐射回用活性炭对水中亚甲基蓝和Cd2＋去除效果的研究

考察了微波-活性炭联合处理技术对模拟染料废水中亚甲基蓝和Cd2＋的去除效果。对于100 mL浓度为1 000 mg/L的亚甲基蓝溶液、活性炭用量为10 g时,新活性炭对亚甲基蓝的去除率为99.99%;采用700 W微波对吸附亚甲基蓝的活性炭辐射10 min进行再生并回用,经微波辐射再生10次后活性炭对亚甲基蓝的去除率为99.68%,未经微波作用反复使用10次的活性炭对亚甲基蓝的去除率为85.41%。结果表明：微波处理有效地减缓了活性炭吸附能力的下降速率,实现了活性炭再生和反复使用。在吸附过程中,Cd2＋使活性炭对亚甲基蓝的吸附能力略有下降,而共存的亚甲基蓝则促进了活性炭对Cd2＋的吸附,对新炭和再生后活性炭物理化学特性的表征证明了活性炭对亚甲基蓝的吸附为物理吸附,对Cd2＋的吸附为化学吸附。     

Application of Fenton's reagent to regenerate activated carbon saturated with organochloro compounds

In this work Fenton's reagent was used to treat activated carbon saturated with organochloro compounds for the oxidation of the adsorbed contaminants and the regeneration of the carbon adsorbent. Activated carbon containing adsorbed chlorinated model substrates such as chlorobenzene, tetrachloroethylene, chloroform or 1,2-dichloropropane was treated with Fenton's reagent at room temperature resulting in a rapid consumption of the organochloro compounds. Thermogravimetric, infrared, BET surface area and MIMS adsorption studies showed that Fenton's treatment has no significant effect on the physico-chemical properties of the activated carbon. The used carbon adsorbents can be efficiently regenerated and recycled with no loss of its adsorption capacity even after five consecutive treatments with Fenton's reagent.     

Effect of advanced oxidants generated via ultraviolet light on a sequentially loaded and regenerated granular activated carbon biofilter

The objective of this research was to investigate a sequentially loaded and regenerated granular activated carbon (GAC) biofilter system and to determine whether regenerative ozonation/advanced oxidation could improve the removal and biodegradation of a volatile organic compound from a contaminated airstream. Bench-scale reactors were constructed to operate in a manner analogous to a commercially available system manufactured by Terr-Aqua Environmental Systems (only with longer contact time). The GAC system consisted of two GAC biofilter beds that operated in a cyclical manner. On a given day, the first GAC bed adsorbed methyl isobutyl ketone from a simulated waste airstream, while the second bed underwent regeneration; then on the next day, the second bed was in the adsorption mode while the first was regenerated. Three bench-scale systems were used to compare the performance under three operating conditions: (1) ozone/ associated oxidant regeneration of a GAC biofilter system that was seeded with microorganisms from a field site, (2) a humid air regeneration of a seeded GAC biofilter, and (3) a humid air regeneration of an unseeded GAC biofilter. For the advanced oxidant regenerated GAC biofilter, a maximum removal efficiency of >95% was achieved with an empty bed contact time of 148 sec and an influent concentration of 125 ppm methyl isobutyl ketone, and 90-95% was achieved at 148-sec empty bed contact time and a 1150-ppm influent.     

Effect of Advanced Oxidants Generated Via Ultraviolet Light on a Sequentially Loaded and Regenerated Granular Activated Carbon Biofilter

Abstract

The objective of this research was to investigate a sequentially loaded and regenerated granular activated carbon (GAC) biofilter system and to determine whether regenerative ozonation/advanced oxidation could improve the removal and biodegradation of a volatile organic compound from a contaminated airstream. Bench-scale reactors were constructed to operate in a manner analogous to a commercially available system manufactured by Terr-Aqua Environmental Systems (only with longer contact time). The GAC system consisted of two GAC biofilter beds that operated in a cyclical manner. On a given day, the first GAC bed adsorbed methyl isobutyl ketone from a simulated waste airstream, while the second bed underwent regeneration; then on the next day, the second bed was in the adsorption mode while the first was regenerated.

Three bench-scale systems were used to compare the performance under three operating conditions: (1) ozone/ associated oxidant regeneration of a GAC biofilter system that was seeded with microorganisms from a field site, (2) a humid air regeneration of a seeded GAC biofilter, and (3) a humid air regeneration of an unseeded GAC biofilter. For the advanced oxidant regenerated GAC biofilter, a maximum removal efficiency of >95% was achieved with an empty bed contact time of 148 sec and an influent concentration of 125 ppm methyl isobutyl ketone, and 90–95% was achieved at 148-sec empty bed contact time and a 1150-ppm influent.     

包埋碳纳米管海藻酸钠凝胶球吸附苯酚的研究

研究了水溶液中碳纳米管及包埋固定于海藻酸钠凝胶球中的碳纳米管吸附苯酚的特性,测定了温度、pH值、转速等因素对吸附的影响,并对吸附剂进行了热脱附再生.绘制了吸附等温线,对吸附机理进行探讨.结果表明,碳纳米管及包埋于海藻酸钠凝胶球中的碳纳米管对苯酚的吸附平衡受pH和转速影响不显著,受温度影响显著,简单的热再生即有很好的再生效果.通过方程拟合,2种吸附剂对苯酚的吸附均符合Langmuir和Freundlich型吸附等温式.     

改性活性炭吸附净化黄磷尾气中的PH_3

通过钢瓶配气模拟和气相色谱GC-14C测定的方法,研究了改性活性炭吸附净化黄磷尾气中PH3的相关问题。得到了吸附反应的最佳吸附温度、氧含量、气体流量、改性液浓度、活性炭粒径和焙烧温度。再生方法可行,可通过再生液回收磷酸。热重差热分析和孔径分布初步证明吸附质为磷和磷氧化物。     

微波辐射回用活性炭对水中亚甲基蓝和Cd~(2+)去除效果的研究

考察了微波-活性炭联合处理技术对模拟染料废水中亚甲基蓝和Cd2+的去除效果。对于100 mL浓度为1 000 mg/L的亚甲基蓝溶液、活性炭用量为10 g时,新活性炭对亚甲基蓝的去除率为99.99%;采用700 W微波对吸附亚甲基蓝的活性炭辐射10 min进行再生并回用,经微波辐射再生10次后活性炭对亚甲基蓝的去除率为99.68%,未经微波作用反复使用10次的活性炭对亚甲基蓝的去除率为85.41%。结果表明:微波处理有效地减缓了活性炭吸附能力的下降速率,实现了活性炭再生和反复使用。在吸附过程中,Cd2+使活性炭对亚甲基蓝的吸附能力略有下降,而共存的亚甲基蓝则促进了活性炭对Cd2+的吸附,对新炭和再生后活性炭物理化学特性的表征证明了活性炭对亚甲基蓝的吸附为物理吸附,对Cd2+的吸附为化学吸附。     

Phosphate removal and recovery with a synthetic hydrotalcite as an adsorbent

Phosphate removal is important to control eutrophication and an ion exchange process is one of several treatment processes for this purpose. Hydrotalcite compounds (HTALs) are useful as adsorbents for phosphate removal because of their ion exchange properties. In this study, the adsorption properties of a granular synthetic HTAL for phosphate and the method of regeneration of the granular HTAL were examined. The adsorption isotherm of the granular HTAL was approximated by a modified Langmuir type, and the maximum adsorption capacity was 47.3 mg P g(-1), which corresponded to the content of HTAL in the granular one. Phosphate adsorbed on the HTAL was effectively desorbed with alkaline NaCl solutions and the HTAL was regenerated with 25 w/v% MgCl(2) solution. The regenerated HTAL could be reused repeatedly for the phosphate removal. Phosphate in the exhausted desorption solution was recovered as a precipitate of calcium phosphate by addition of CaCl(2), and the residual exhausted desorption solution could be also reused after supplying NaOH. The results suggest the possibility of an effective system for phosphate removal and recovery, which includes the following processes: adsorption, desorption, recovery of phosphate, and regeneration of the HTAL and the desorption solution.     

平板炭气凝胶电极电吸附除氟

采用自制的炭气凝胶平板电极进行模拟水样中氟的电吸附去除研究,通过单因子实验优化了该电吸附技术的操作参数和适用的溶液条件,并研究了反接电极法的再生效果。研究结果表明,自制的炭气凝胶平板由纳米颗粒组成三维网络结构,比表面积为670.90 m2/g,具有良好的充放电可逆性和迅速形成表面双电层的特点。静态电吸附除氟效果最佳的条件为:水样氟离子浓度6 mg/L,pH 7.0,极板间距4 cm,电压1.6 V;共存物质硝酸根、腐殖酸、碳酸根和碳酸氢根等对氟离子的电吸附具有一定的促进作用。吸附氟离子后的炭气凝胶材料的比表面、孔体积、电容值有所减小。对于吸附氟离子后的炭气凝胶平板电极,采用反接电极法取得较好再生效果的条件为:流动状态、电压1.6 V、极板间距4 cm。再生后的炭气凝胶电极与原始炭气凝胶相比,依然具有良好的充放电可逆性。     

Removal and Destruction of Organic Contaminants in Water Using Adsorption,Steam Regeneration,and Photocatalytic Oxidation: A Pilot-Scale Study

ABSTRACT

The overall objective of this pilot-scale study is to investigate the technical feasibility of the removal and destruction of organic contaminants in water using adsorption and photocatalytic oxidation. The process consists of two consecutive operational steps: (1) removal of organic contaminants using fixed-bed adsorption; and (2) regeneration of spent adsorbent using photocatalysis or steam, followed by decontamination of steam condensate using photocatalysis. The pilot-scale study was conducted to evaluate these options at a water treatment plant in Wausau (Wisconsin) for treatment of groundwater contaminated with tetrachloroethene (PCE), trichloroethene (TCE), cis-dichloroethene (cis-DCE), toluene, ethylbenzene (EB), and xylenes. The adsorbents used were F-400 GAC and Ambersorb 563.

In the first treatment strategy, the adsorbents were impregnated with photocatalyst and used for the removal of aqueous organics. The spent adsorbents were then exposed to ultraviolet light to achieve photocatalytic regeneration. Regeneration of adsorbents using photocatalysis was observed to be not effective, probably because the impregnated photocatalyst was fouled by background organic matter present in the groundwater matrix.

In the second treatment strategy, the spent adsorbents were regenerated using steam, followed by cleanup of steam condensate using photocatalysis. Four cycles of adsorption and three cycles of steam regeneration were performed. Ambersorb 563 adsorbent was successfully regenerated using saturated steam at 160 °C within 20 hours. The steam condensate was treated using fixed-bed photo-catalysis using 1% Pt-TiO₂ photocatalyst supported on silica gel. After 35 minutes of empty bed contact time, more than 95% removal of TCE, cis-DCE, toluene, EB, and xylenes was achieved, and more than 75% removal of PCE was observed.

In the case of activated carbon adsorbent, steam regeneration was not effective, and a significant loss in adsorbent capacity was observed.     

改性活性炭吸附净化黄磷尾气中的PH3

通过钢瓶配气模拟和气相色谱GC-14C测定的方法，研究了改性活性炭吸附净化黄磷尾气中PH₃的相关问题。得到了吸附反应的最佳吸附温度、氧含量、气体流量、改性液浓度、活性炭粒径和焙烧温度。再生方法可行，可通过再生液回收磷酸。热重差热分析和孔径分布初步证明吸附质为磷和磷氧化物。     

Adsorption of paraquat on the physically activated bleaching earth waste from soybean oil processing plant

A series of regeneration experiments with physical activation were carried out on bleaching earth waste from the soybean refining process in a rotary reactor. The influence of activation parameters on the spent clay by varying the holding time of 1 to approximately 4 hours and temperature of 700 to approximately 900 degrees C was determined. The variations of pore properties as well as the change of chemical characteristics in the resulting solids were also studied. Results showed that the resulting samples were type IV with hysteresis loops corresponding to type H3 from nitrogen adsorption-desorption isotherms, indicating slit-shaped mesoporous characteristics. However, the regenerated clays had smaller surface areas (70 to approximately 117 m2/g) than that (245 m2/g) of fresh bleaching earth. Under the physical activation conditions investigated, the holding time of 1 hour and temperature of 700 degrees C were found to be optimal conditions for producing mesoporous clay with physical activation. The adsorption of paraquat on regenerated sample was also evaluated. The isotherm showed that the regenerated sample still had a high affinity for this herbicide. Thus, the regeneration of this agro-industrial waste is one option for utilizing the clay resource, and it may be used for water treatment applications to remove organic contaminants.     

Woody biomass and RPF gasification using reforming catalyst and calcium oxide

This study focused on steam gasification and reforming of waste biomass using a reforming catalyst. The purpose of the study was to evaluate the durability of a commercial Ni reforming catalyst and the effect of CaO on the reforming behavior, and to clarify detailed factors of catalytic performance, as well as the effect of operating parameters on the characteristics of produced gas composition. Moreover, catalyst regeneration was carried out and the behavior of catalytic activity based on gas composition was investigated. Using a fluidized bed gasifier and a fixed bed reformer, gasification and reforming of waste biomass were carried out. Commercial Ni-based catalyst and calcined limestone (CaO) were applied to the reforming reaction. Temperature of the gasifier and reformer was almost 1023 K. Ratio of steam to carbon in the feedstock [mol mol⁻¹] and equivalence ratio (i.e., ratio of actual to theoretical amount of oxygen) [-] were set at about 2 and 0.3, respectively. The feed rate of the feedstock into the bench-scale gasifier was almost 15 kg h⁻¹. The results of waste biomass gasification confirmed the improvement in H₂ composition by the CO₂ absorption reaction using the reforming catalyst and CaO. In addition, CaO proved to be especially effective in decreasing the tar concentration in the case of woody biomass gasification. Catalytic activity was maintained by means of catalyst regeneration processing by hydrogen reduction after air oxidation when woody biomass was used as feedstock.     

微波辅助-活性炭法处理电厂EDTA锅炉清洗废水可行性研究

采用微波辅助-活性炭法处理电厂EDTA锅炉清洗废水,研究了微波辐射时间、微波功率以及再生次数对活性炭吸附能力的影响,并根据实验结果设计了工艺流程,分析了微波辅助-活性炭法处理电厂EDTA锅炉清洗废水的可行性.研究表明,微波辅助-活性炭法处理EDTA清洗废水的最佳微波辐射时间和微波功率分别为5 min和680 W,微波辐...     

Determining Impaction Efficiencies of Mist Collection Equipment

High temperature sulfur removal can be achieved with calcium-based sor-bents (e.g. dolomite) in fluidized-bed çoal gasification systems now being developed for power generation. The use of dolomite offers the opportunity to meet environmental emission standards, to minimize energy losses, and to reduce electrical energy costs.

In addition to removing sulfur from the low-Btu gas, the complete sulfur removal system must be integrated with the total power plant and environment to assure compatibility. Critical requirements for achieving commercial system include establishing criteria for ‘acceptable’ sorbents, establishing integrated sulfur removal/gasification process design parameters, predicting trace element release, predicting sorbent attrition, developing an economic regeneration and/or once through process option, developing a spent sorbent processing system, and establishing safe and reliable disposition options for spent sorbent. Design and operating parameters are being developed and potential process limitations are identified.     

Retention of chromium (VI) on a macroporous char following ChemChar gasification and successive leaching with water and acids.

A granular macroporous char, triple-reverse-burn (TRB) char, was loaded with 23.40 mg Cr/g TRB char from an aqueous solution, and the retained metal was leached by water, 0.66 M nitric acid, concentrated nitric acid, and concentrated hydrochloric acid before and after treatment by a reductive thermal gasification process (ChemChar process developed by ChemChar Research, Inc., Columbia, Missouri). The chromium leachate was analyzed by flame atomic adsorption. Reverse- and forward-mode gasifications were performed on the metal-laden char. With the exception of a 10% mass loss of carbon, the reverse mode gasification process does not change the physical characteristics of the granular char, but does increase the retention of the chromium from 16.7 to 24.2%, depending on the leachant. The forward mode gasification process produces a vitrified (or glasslike) ash residue. There was an 11.6 to 13.1% increase in the retention of the chromium by the slag and ash when compared to the nongasified chromium-loaded TRB char. Chromium (VI) was effectively removed from solution by TRB char and found to be retained to a higher degree on the char after a reductive thermal treatment.