Extended Analytical Turbulent Diffusion Model for Particle Dispersion and Deposition in a Horizontal Pipe: Comparison with CFD Simulation

A 2D analytical turbulent diffusion model for particle dispersion and deposition at different heights along the pipe flow and circumferential deposition has been developed. This liquid–solid turbulent diffusion model presented in this paper has emanated from an existing gas–liquid turbulent diffusion model. This model can be used as a handy tool for quick estimation one and two-dimensional deposition fluxes of particles in water distribution networks. A comprehensive 3D numerical investigation has been carried out using multiphase mixture model available in “Fluent 6.2” to verify the above analytical model. Different particles sizes and densities were used for 3D numerical investigations. The deposition was studied as a function of particle diameter, density, and fluid velocity. The deposition of particles, along the periphery of the pipe wall and at different depths, was investigated. Both the models findings matched with qualitative phenomena such as deposition of heavier particles at the bottom of the pipe wall were higher at lower velocities and lower at higher velocities. The lighter particles were found mostly suspended with homogeneous distribution. Smaller particles were also suspended with marginal higher concentration near the bottom of the pipe wall. This marginal higher concentration of the smaller particles was found to be slightly pronounced for lower velocity. These analogies of particles are well discussed with the ratio between free-flight velocity and the gravitational settling velocity. Extended analytical model results were compared with the 3D computational fluid dynamics simulation results. Discrepancies in the model results were discussed.     

Verification of a depth-integrated sample arm as a means to reduce solids stratification bias in urban stormwater sampling

A new water sample collection system was developed to improve representation of solids entrained in urban stormwater by integrating water-quality samples from the entire water column, rather than a single, fixed point. The depth-integrated sample arm (DISA) was better able to characterize suspended-sediment concentration and particle size distribution compared to fixed-point methods when tested in a controlled laboratory environment. Median suspended-sediment concentrations overestimated the actual concentration by 49 and 7% when sampling the water column at 3- and 4-points spaced vertically throughout the water column, respectively. Comparatively, sampling only at the bottom of the pipe, the fixed-point overestimated the actual concentration by 96%. The fixed-point sampler also showed a coarser particle size distribution compared to the DISA which was better able to reproduce the average distribution of particles in the water column over a range of hydraulic conditions. These results emphasize the need for a water sample collection system that integrates the entire water column, rather than a single, fixed point to properly characterize the concentration and distribution of particles entrained in stormwater pipe flow.     

Morphological characterization of suspended particles under wind-induced disturbance in Taihu Lake, China

Sediments are disturbed by wind frequently, especially in the shallow lakes. The characteristics of resuspended sediment particles in Taihu Lake were studied under different wind velocities. It showed that sediment particles suspended obviously and particle number in overlying water increased directly under high wind-induced disturbance. Suspended solid (SS) concentration was less than 50 mg/l when the wind velocity was below 3.0 m/s, however, it increased to more than 300 mg/l when the wind velocity was 10.0 m/s. Two methods were used to measure the fractal characteristics of particles. One was light scattering and the other was image analysis. The three-dimensional fractal dimensions of suspended particles, measured by light scattering, were between 2.26 and 2.44; correspondingly, the two-dimensional fractal dimensions, calculated by image analysis, were between 1.44 and 1.77. Moreover, the three-dimensional fractal dimensions were directly proportional to two-dimensional fractal dimensions. The characteristic length of particles was calculated by image analysis. The minimum characteristic length was close to 8.5 μm when the wind velocity was 1.5 m/s at 50 cm beneath lake surface, while, the maximum characteristic length was approximate to 24 μm when the wind velocity was 10 m/s at the depth of 150 cm.     

Pool of Dust Particles over the Asian Continent: Balloon-borne Optical Particle Counter and Ground-based Lidar Measurements at Dunhuang, China

Measurements of aerosols were made in 2001 and 2002 at Dunhuang (40 degrees 00'N, 94 degrees 30'E), China to understand the nature of atmospheric particles over the desert areas in the Asian continent. Balloon-borne measurements with an optical particle counter suggested that particle size and concentration had noticeable peaks in super micron size range not only in the boundary mixing layer but also in the free troposphere. Super-micron particle concentration largely decreased in the mid tropopause (from 5 to 10 km; above sea level, a.s.l.). Lidar measurements made during August 2002 at Dunhuang suggested the possibility that mixing of dust particles occurred from near the ground to about 6 km even under calm weather conditions, and a large depolarization ratio of particulate matter was found in the aerosol layer. The top of the aerosol layer was found at heights of nearly 6 km (a.s.l.). It is strongly suggested that nonspherical dust particles (Kosa particles) frequently diffused in the free atmosphere over the Taklamakan desert through small-scale turbulences and are possible sources of dust particles of weak Kosa events that have been identified in the free troposphere not only in spring but also in summer over Japanese archipelago. Electron microscopic experiments of the particles collected in the free troposphere confirmed that coarse and nonspherical particles observed by the mineral particle were major components of coarse mode (diameter larger than 1 microm) below about 5 km over Dunhuang, China.     

Modeling of Hydrodynamics and Cohesive Sediment Processes in an Estuarine System: Study Case in Danshui River

The Danshui River estuarine system is the largest estuarine system in northern Taiwan and is formed by the confluence of Tahan Stream, Hsintien Stream, and Keelung River. A comprehensive one-dimensional (1-D) model was used to model the hydrodynamics and cohesive sediment transport in this branched river estuarine system. The applied unsteady model uses advection/dispersion equation to model the cohesive sediment transport. The erosion and deposition processes are modeled as source/sink terms. The equations are solved numerically using an implicit finite difference scheme. Water surface elevation and longitudinal velocity time series were used to calibrate and verify the hydrodynamics of the system. To calibrate and verify the mixing process, the salinity time series was used and the dispersion coefficient of the advection/dispersion equation was determined. The cohesive sediment module was calibrated by comparing the simulated and field measured sediment concentration data and the erosion coefficient of the system was determined. A minimum mean absolute error of 4.22 mg/L was obtained and the snapshots of model results and field measurements showed a reasonable agreement. Our modeling showed that a 1-D model is capable of simulating the hydrodynamics and sediment processes in this estuary and the sediment concentration has a local maximum at the limit of salinity intrusion. Furthermore, it was indicated that for Q ₅₀ (the flow which is equaled or exceeded 50% times), the turbidity maximum location during neap tide is about 1 km closer to the mouth compared to that during spring tide. It was found that deposition is the dominant sediment transport process in the river during spring–neap periods. It was shown that, while sediment concentration at the upstream depends on the river discharge, the concentration in the downstream is not a function of river discharge.     

The effect of wind direction on the observed size distribution of particle adsorbed polycyclic aromatic hydrocarbons on an inner city sampling site

An investigation of the variability in the size distribution of particle adsorbed polycyclic aromatic hydrocarbons (PAHs) on an inner city sampling site showed differences depending on the wind direction. Particle size distributions of PAHs from outdoor air sampling were measured in Munich from 1994 to 1997. The sampling site is located northeast of a crossing with heavy traffic and southwest of a large inner city park. Depending on the wind direction, three different size distributions of particle adsorbed PAHs were observed. The maximum PAH concentration on very small particles (geometric mean diameter 75 nm) was observed with wind from west to southwest coming directly from the crossing area or the roads with heavy traffic. The maximum PAH concentration on particles with geometric mean diameter of 260 nm was found on days with wind from the built-up area north of the sampling site. On particles with geometric mean diameter of 920 nm the maximum PAH concentration was found on days with main wind directions from northeast to east. On these days the wind is blowing from the direction of the city park nearby. The distribution of particle adsorbed PAHs within different particle size classes is substantially influenced by the distance of the sampling site from strong sources of PAH loaded particulate matter.     

Concentration gradient patterns of aerosol particles near interstate highways in the Greater Cincinnati airshed

The objective of this study was to determine if there is an exposure gradient in particulate matter concentrations for people living near interstate highways, and to determine how far from the highway the gradient extends. Air samples were collected in a residential area of Greater Cincinnati in the vicinity of two major highways. The measurements were conducted at different distances from the highways by using ultrafine particle counters (measurement range: 0.02-1 microm), optical particle counters (0.3-20 microm), and PM2.5 Harvard Impactors (0.02-2.5 microm). The collected PM2.5 samples were analyzed for mass concentration, for elemental and organic carbon, and for elemental concentrations. The results show that the aerosol concentration gradient was most clearly seen in the particle number concentration measured by the ultrafine particle counters. The concentration of ultrafine particles decreased to half between the sampling points located at 50 m and 150 m downwind from the highway. Additionally, elemental analysis revealed a gradient in sulfur concentrations up to 400 m from the highway in a residential area that does not have major nearby industrial sources. This gradient was qualitatively attributed to the sulfate particle emissions from diesel engine exhausts, and was supported by the concentration data on several key elements indicative of traffic sources (road dust and diesel exhaust). As different particulate components gave different profiles of the diesel exposure gradient, these results indicate that no single element or component of diesel exhaust can be used as a surrogate for diesel exposure, but more comprehensive signature analysis is needed. This characterization is crucial especially when the exposure data are to be used in epidemiological studies.     

The Effect of Traction Sanding on Urban Suspended Particles in Finland

Springtime urban road dust forms one of the most serious problems regarding air pollution in Finland. The composition and origin of springtime dust was studied in southern Finland with two different methods. Suspended particles (PM10 and TSP) were collected with high volume particle samplers and particle deposition was collected with moss bags. The composition of the PM(1.5-10) fraction was studied using individual particle analysis with SEM/EDX. The deposition in the moss bags was analysed with ICP-MS. The results showed that during the study period, approximately 10% of both PM(1.5-10) particles and the deposition originated from sanding. Other sources in the springtime PM(1.5-10) were e.g. asphalt aggregate or soil and combustion processes. It can be concluded that sanding produced a relatively small amount of particulate matter under the investigated circumstances.     

化工装置停工放空过程中VOCs排放及估算方法

通过分析化工企业典型开、停车过程的排污节点,表明停车过程中大气挥发性有机污染物主要来自装置退料结束后挂壁、底部滞留和内部空间蒸气等滞留在设备内部的残余物料。在总结化工装置停工放空过程中大气挥发性有机物来源的基础上,讨论并提出大气污染排放量估算方法。     

Submicron particle characteristics of atmospheres in a long highway tunnel

This study used a scanning mobility particle sizer (SMPS) to measure and categorize submicron atmospheric particles in the 14–737-nm size range for ambient and urban roadside air and for air in the Hsuehshan Tunnel (12.9 km), Taiwan. Principal component analysis, traffic flow, and particle size distributions were used to identify the emission characteristics of light-duty vehicles (LDV) with the SMPS data. In the Hsuehshan Tunnel, the particle size from the majority of emissions discharged by LDV is approximately 20–60 nm, and the maximum particle number can reach up to 2.5?×?10⁵. In contrast, submicron particle size distribution for urban roadsides is mostly 14–200 nm, and the maximum particle number is approximately 4?×?10⁴ with the particle number for most particle sizes being below 1,200. The submicron particle size distribution at the ambient air station was unimodal with a mode sizes at 30–50 nm with the maximum particle number of 3,000.     

Workplace aerosol mass concentration measurement using optical particle counters

Direct-reading aerosol measurement usually uses the optical properties of airborne particles to detect and measure particle concentration. In the case of occupational hygiene, mass concentration measurement is often required. Two aerosol monitoring methods are based on the principle of light scattering: optical particle counting (OPC) and photometry. The former analyses the light scattered by a single particle, the latter by a cloud of particles. Both methods need calibration to transform the quantity of scattered light detected into particle concentration. Photometers are simpler to use and can be directly calibrated to measure mass concentration. However, their response varies not only with aerosol concentration but also with particle size distribution, which frequently contributes to biased measurement. Optical particle counters directly measure the particle number concentration and particle size that allows assessment of the particle mass provided the particles are spherical and of known density. An integrating algorithm is used to calculate the mass concentration of any conventional health-related aerosol fraction. The concentrations calculated thus have been compared with simultaneous measurements by conventional gravimetric sampling to check the possibility of field OPC calibration with real workplace aerosols with a view to further monitoring particle mass concentration. Aerosol concentrations were measured in the food industry using the OPC GRIMM? 1.108 and the CIP 10-Inhalable and CIP 10-Respirable (ARELCO?) aerosol samplers while meat sausages were being brushed and coated with calcium carbonate. Previously, the original OPC inlet had been adapted to sample inhalable aerosol. A mixed aerosol of calcium carbonate and fungi spores was present in the workplace. The OPC particle-size distribution and an estimated average particle density of both aerosol components were used to calculate the mass concentration. The inhalable and respirable aerosol fractions calculated from the OPC data are closely correlated with the results of the particle size-selective sampling using the CIP 10. Furthermore, the OPC data allow calculation of the thoracic fraction of workplace aerosol (not measured by sampling), which is interesting in the presence of allergenic particles like fungi spores. The results also show that the modified COP inlet adequately samples inhalable aerosol in the range of workplace particle-size distribution.     

Processing and analysis of roadway runoff micro (< 20 μm) particles

This study was performed to compare paper and sieving filtration methods for processing micro particles (< 20 μm) in roadway runoff for water quality evaluation. The consequence of a lack of reliable particle processing on particle number, particle concentration and particulate elemental composition, as well as their influence on particle mass and pollutant load calculations, is discussed. Results show that the paper filtering method can affect the measurement of particle size distributions of highway runoff samples. Contrary to common practice, it is not always correct to assume that the number and concentration of particles < 38 μm is the same as the number and concentration of particles < 20 μm. Processed samples for micro particles were most similar to unprocessed samples when nylon sieves were used. Samples filtered by paper deviated significantly from unprocessed samples. These deviations can cause inaccuracies up to 90 percent, in particle count and concentration, TSS calculations, elemental mass composition, and particle and elemental mass loading.     

Biosphere atmosphere exchanges: Ozone and aerosol dry deposition velocities over a pine forest

Measurements of dry deposition velocities for ozone and aerosol particles has been measured over a pine forest in the south-west of France by the eddy correlation method. Low frequency fluctuations in the variations of scalars can introduce erroneous values of vertical fluxes for ozone and aerosol particles but also, in some cases of low wind, for momentum and heat. The dry deposition velocity variations are similar for ozone and aerosol, although the mechanism of deposition are different. In the case of aerosol particles a parametrization, not far from that of Wesely et al. (1985) can be given.     

Measurements of atmospheric aerosol size distributions by co-located optical particle counters

Ambient aerosol number concentrations and size distributions were measured in both indoor and outdoor environments using two identical co-located and concurrently operated optical particle counters (OPCs). Indoor measurements were performed in a research laboratory, whereas two different locations were used for outdoor measurements; the sampling duration exceeded 12 hours and one hour respectively. Results from the two OPCs have been presented for eight size classes between 0.5 and 20 [micro sign]m, represented by central value diameters 0.875, 1.5, 2.75, 4.25, 6.25, 8.75, 12.5 and 15 microm. Overall, for the six indoor and outdoor experiments conducted at different times of day, the mean particle count ratios from the two OPCs for the individual samples showed +/-20% variation for indoor experiments and +/-50% variations for outdoor experiments. Significant random departures of the mean ratios from unity at all size classes were noticed even for indoor sample periods exceeding 20 hours. However, the coefficient of determination (R(2)) for the plots of readings from the two OPCs indicated higher consistency for "fine" particles (0.5-3.5 microm) than for "coarse" particles (10-20 microm), with average R(2) > 0.8 and R(2) < 0.5 respectively. Poisson counting statistics help to explain the divergence in the latter case where number concentrations were very low for the outdoor experiments. However, it cannot explain the divergence for indoor measurements where the concentrations were much higher. Increasing the averaging period reduced the scatter, especially in size classes with low number concentration. However, this procedure may lead to over-smoothing of data for environments with rapidly changing number concentration. These results indicate that, when two such analysers are used for comparative studies, the divergence between their responses may generate significant values of source contribution or deposition flux, even for nominally similar aerosol populations.     

Airborne Dust Particle Counting Techniques

The paper briefly describes an electro-optical system for counting of dust particles, which is based on the scattering phenomena.Utilizing the scattering of light by various size particles present in the environment, various particle counting techniques have been developed in order to measure the scattered intensity of light. Light scatters in all directions but much more in the so-called near forward direction 17^∘ off axis, at 163^∘ from the light source in the visible range.On the basis of two techniques, the right angle and forward angle scattering, opto-mechanical systems have been developed which measure scattered intensity and particulate matter. The forward scattering Nephelometer is more sensitive and therefore is more suitable for pollution monitoring than the right angle scattering Nephelometer. Whereas the right angle scattering Nephelometer has the utility in extremely low concentration in ppb level owing to the excellent light trap efficiency in comparison to forward scattering Nephelometer. In this paper measurement techniques and measurement results associated with design and development of a real time particle analyser are also discussed.     

重庆城区不同粒径颗粒物元素组分研究及来源识别

为研究重庆市大气颗粒物的污染特征及其来源,于2010年3—10月在主城区分别采集PM_1.0、PM_2.5和PM₁₀3种粒径的颗粒物样品,利用XRF分析其中的26种元素浓度。结果表明,重庆市主城区S元素在各粒径中含量都较高,细粒子中K的含量较高,粗粒子中Si、Ca和Fe的浓度较大。富集因子分析表明,主城区Cd、S、Se等污染元素的富集系数较大,且粒径越小,富集现象越明显。利用因子分析得出土壤风沙、扬尘、燃煤的燃烧、机动车燃油产生的尾气排放、生物质燃烧排放是重庆市颗粒物污染的主要来源。     

Numerical Simulations of Wind Induced Particle Contamination in Gypsum Landfill Surroundings

The contribution presents numerical simulation of gypsum particles, lifting from a gypsum landfill. First, particle characteristics are presented, resulting from different technologies of gypsum depositing. Next, a laboratory experiment parameter validation tests are described, which served as a means of determination of mass flow of particles from the landfill. The background of the numerical simulations, used in the assessment of landfill impact on the environment, is also described. Simulations consist of two parts: simulation of a long term impact of the particles on the surrounding area, performed by implementation of the Gaussian dispersion model based computer code ISC3, and second, a CFD based simulation for assessing the flow and mass concentration fields in the vicinity of the landfill for several pre-selected flow cases. The results of both computational approaches are presented and compared. In the conclusions, a relation of the simulation results with existing environmental pollution levels is made, and recommendations for landfill management are drawn.     

A comprehensive method for aeolian particle granulometry and micromorphology analyses

The aim of this study was to use a new approach to investigate aeolian particle granulometry and micromorphology. Taking total aeolian deposition into account, we used parameters such as, particle area, perimeter, shape analysis for particle roughness (area/perimeter) and elongation (long/short axis). These parameters were analyzed on temporal and spatial scales at four study sites in the eastern Negev Desert, Israel. The total collection of particles was sorted into three size groups based on particle area to facilitate comparison. The classic definition of particle size (equating particle length with particle diameter) produced relatively small variations among the three size classes (25-38.6%). Our proposed comprehensive method demonstrated significant variation among the three size classes (13.9-60.8%), e.g. the classic method placed 36.4% of the particles in size class two while the new method placed 60.8% of the particles in this size class; the differences were even more significant regarding size class 3 (38.6% vs. 13.9%, respectively). The classic method did not facilitate investigation of particle roughness and elongation. With this new approach, it was possible to clearly define the particles by size class, based on these characteristics. With roughness, the variation among size classes 2 and 3 was about 27%. With elongation, the variation among size classes two and three was about 21%. Applying similar investigation method to study the aeolian particle granulometry and micromorphology can better facilitate more detailed calculation of particle size distribution, roughness and elongation.     

Aerosol size distributions in urban Jinan: Seasonal characteristics and variations between weekdays and weekends in a heavily polluted atmosphere

Aerosol size distributions, trace gas, and PM(2.5) concentrations have been measured in urban Jinan, China, over 6 months in 2007 and 2008, covering spring, summer, fall, and winter time periods. Number concentrations of particles (10-2,500 nm) were 16,200, 13,900, 11,200, and 21,600 cm(?-3) in spring, summer, fall, and winter, respectively. Compared with other urban studies, Jinan has higher number concentrations of accumulation-mode particles (100-500 nm) and particles (10-2,500 nm), but lower concentrations of ultrafine particles (10-100 nm). The number, surface and volume concentrations, and size distributions of particles showed obvious seasonal variation and are also influenced by traffic emissions. Through correlation analysis, traffic emissions are proposed to be a more important contributor to Atkien-mode and accumulation-mode particles than coal firing. Around midday, the presence of nanoparticles and new particle formation is limited to pre-existing particles from traffic emissions and the mass transport of particles from suburban and rural areas. Compared with other studies in urban areas of Europe and the USA, the variation of particle number concentration and related gas concentration in Jinan between weekdays and weekends is smaller and the reasons has been deduced.