CuO-TiO2/导电聚合物纤维复合材料的制备及其光催化性能

利用高压静电纺丝技术,制得含羧基的导电聚合物纤维(聚偏氟乙烯/苯乙烯-马来酸酐共聚物/纳米石墨).水热条件下在纤维表面原位合成了纳米级的TiO2,再通过水热法在TiO2表面制备了微米级的球形CuO颗粒,得到CuO-TiO2/导电聚合物纤维复合材料.运用扫描电子显微镜(SEM)、X射线衍射仪(XRD)、紫外-可见吸收光谱仪(UV-Vis)和热失重分析(TGA)对复合材料的结构与性能进行表征,并利用氙灯模拟太阳光进行光催化降解次甲基蓝实验.结果发现,CuO-TiO2/导电聚合物纤维复合材料的降解效率高于CuO-TiO2/非导电聚合物纤维、CuO-TiO2粉体和Degussa P25,光催化降解3.5h时,次甲基蓝的残留率为4.7％.     

Graphene TiO2 nanocomposites with high photocatalytic activity for the degradation of sodium pentachlorophenol

A series of graphene–TiO2photocatalysts was synthesized by doping TiO2 with graphene oxide via hydrothermal treatment. The photocatalytic capability of the catalysts under ultraviolet irradiation was evaluated in terms of sodium pentachlorophenol（PCP-Na） decomposition and mineralization. The structural and physicochemical properties of these nanocomposites were characterized by X-ray diffraction, N2adsorption–desorption, transmission electron microscopy, scanning electron microscopy, Ultraviolet–visible diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, electron paramagnetic resonance spectra, and Fourier-transform infrared spectroscopy. The graphene–TiO2nanocomposites exhibited higher photocatalytic efficiency than commercial P25 for the degradation of PCP-Na, and 63.4% to 82.9% of the total organic carbon was fully mineralized. The improved photocatalytic activity may be attributed to the accelerated interfacial electron-transfer process and the significantly prolonged lifetime of electron-hole pairs imparted by graphene sheets in the nanocomposites. However,excessive graphene and the inhomogeneous aggregation of TiO2 nanoparticles may decrease photodegradation efficiency.     

TiO2/粉煤灰光催化降解双氯芬酸钠研究

以燃煤电厂外排的废弃物粉煤灰(CFA)为载体,采用混合泥浆法将TiO2负载在CFA的表面,得到一种新型的复合光催化剂TiO2/CFA.对TiO2/CFA进行了扫描电镜分析、X射线衍射分析和氮吸附测试,并以双氯芬酸钠的光催化降解为评价手段,研究了TiO2负载量对TiO2/CFA光催化性能及重复使用性能的影响.结果表明,TiO2负载量的增加有助于提高TiO2/CFA的光催化性能,但当TiO2负载量过高时,CFA上的TiO2在水处理过程中容易脱落,对TiO2/CFA光催化剂的重复使用性能不利.本研究中,最佳的TiO2负载量约为50%,循环使用6次,其光催化降解效率没有明显降低,双氯芬酸钠的降解率均可达70%以上.     

FeTiO3/TiO2纳米异质结的制备和可见光催化性能

采用水热法和溶胶凝胶法制备了新型FeTiO3/TiO2纳米异质结复合材料,并明确了最优的掺杂比例(0.5%).随后利用X射线衍射能谱(XRD)、紫外-可见漫反射光谱(UV-Vis DRS)、扫描电镜(SEM)和透射电镜(TEM)等手段对该复合材料进行表征,证实了其结晶度、吸光度随掺杂量的规律性变化.电镜照片显示,该复合材料具有蓬松多孔的微观结构,且晶格条纹清晰、分散度高,有利于光电子的传导.对苯的降解实验表明,相比于纯TiO2,该催化剂的气相可见光催化能力大幅提高,降解率提升了3倍,达到40%,而CO2生成量提升了5倍,超过300 ppm.同时,电化学测试和电子顺磁共振谱(ESR)等均证实,FeTiO3的窄能带能够提高TiO2的光响应,实现可见光激发;而二者的能带相互匹配,有助于转移光生载流子,实现电子-空穴的高效分离,进而其光生电子和自由基生成能力大幅增强,因此,表现出了较强、较稳定的光催化活性.     

Photocatalytic activity of TiO2 containing anatase nanoparticles and rutile nanoflower structure consisting of nanorods

A series of TiO2 with different crystal phases and morphologies was synthesized via a facile hydrothermal process using titanium nbutoxide and concentrated hydrochloric acid as raw materials. The photocatalytic activity of the samples was evaluated by degradation of Methyl Orange in aqueous solution under UV-Visible light irradiation. On the basis of detailed analysis of the characterizing results of high-resolution transmission electron microscopy, X-ray powder diffraction measurements, X-ray photoelectron spectroscopy and Brunauer-Emmett-Teller measurement, it was concluded that the photo-activity of the catalyst is related directly to the 3D morphology and the crystal phase composition. An excellent catalyst should have both a futile 3D flower-like structure and anatase granulous particles. The 3D flower-like structure could enhance light harvesting, as well as the transfer of reactant molecules from bulk solution to the reactive sites on TiO2. In addition, the optimum anatase/rutile phase ratio was found to be 80：20, which is beneficial to the effective separation of the photogenerated electron-hole pairs.     

Simulated-sunlight-activated photocatalysis of Methylene Blue using cerium-doped SiO2/TiO2 nanostructured fibers

Cerium-doped SiO₂/TiO₂ nanostructured fibers were fabricated by electrospinning technology. The prepared fibers were characterized by thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). Using the fibers as catalysts, photocatalytic degradation of Methylene Blue (MB) aqueous solution was carried out under simulated sunlight. The 0.2% Ce doping proved to be the optimal concentration for the doping of TiO₂/SiO₂, compared to other Ce-doped molar concentrations. The 0.2% Ce-doped SiO₂/TiO₂ fibers exhibited higher photocatalytic activity than industrial Degussa P25 and the samples doped with only Ce or SiO₂. The reasons for improving the photocatalytic activity were also discussed. Several operational parameters were studied, which showed that the photocatalytic efficiency of MB was influenced by parameters such as the initial dye concentration, the initial pH, inorganic anions, and so on. In addition, the influences of an electron acceptor and a radical scavenger suggested that OH was the dominant photooxidant during the photocatalytic process. The reuse evaluation of the fibers indicated that their photocatalytic activity had good stability.     

Multi-function adsorbent-photocatalyst MXene-TiO2 composites for removal of enrofloxacin antibiotic from water

MXenes, a new family of two-dimensional transition metal carbides or nitrides, have attracted tremendous attention for various applications due to their unique properties such as good electrical conductivity, hydrophilicity, and ion intercalability. In this work, Ti₃C₂ MXene, or MX, is converted to MX-TiO₂ composites using a simple and rapid microwave hydrothermal treatment in HCl/NaCl mixture solution that induces formation of fine TiO₂ particles on the MX parent structure and imparts photocatalytic activity to the resulting MX-TiO₂ composites. The composites were used for enrofloxacin (ENR), a frequently found contaminating antibiotic, removal from water. The relative amount of the MX and TiO₂ can be controlled by controlling the hydrothermal temperature resulting in composites with tunable adsorption/photocatalytic properties. NaCl addition was found to play important role as composites synthesized without NaCl could not adsorb enrofloxacin well. Adding NaCl into the hydrothermal treatment causes sodium ions to be simultaneously intercalated into the composite structure, improving ENR adsorption greatly from 1 to 6 mg ENR/g composite. It also slows down the MX to TiO₂ conversion leading to a smaller and more uniform distribution of TiO₂ particles on the structure. MX-TiO₂/NaCl composites, which have sodium intercalated in their structures, showed both higher ENR adsorption and photocatalytic activity than composites without NaCl despite the latter having higher TiO₂ content. Adsorbed ENR on the composites can be efficiently degraded by free radicals generated from the photoexcited TiO₂ particles, leading to high photocatalytic degradation efficiency. This demonstrates the synergetic effect between adsorption and photocatalytic degradation of the synthesized compounds.     

C3N4/BiOBr复合可见光催化剂的性能及其作用机制

利用水热合成法制备了C_3N_4/BiOBr复合可见光催化剂,通过XRD、FT-IR、SEM、DRS、PL等手段对催化剂的物相组成和光化学性能进行了系统表征,利用对罗丹明B(RhB)的降解实验评价了催化剂在可见光照下的光催化降解活性和稳定性并通过ESR分析和自由基捕获实验探究了RhB的光催化降解机制.结果表明,水热合成法可成功制备结晶性能良好的C_3N_4/BiOBr复合可见光催化剂;C_3N_4的复合降低了BiOBr光催化剂的电子-空穴的复合,提高了光催化降解活性,其中15%C_3N_4/BiOBr的活性最佳,可见光照18 min后RhB的脱色率达100%,较纯BiOBr提高了1.5倍,且重复使用5次后仍具有较高的光催化降解活性;复合催化剂光催化降解RhB过程中参与降解的主要活性物种为空穴(h~+)和超氧自由基(·O_2~-),其中h~+影响更为显著.     

Synergistic effect of N- and F-codoping on the structure and photocatalytic performance of TiO2

Three types of TiO₂ nanostructures were synthesized via a facile hydrolysis method at 195 °C. Effects of the preparation method and doping with N and F on the crystal structure and photocatalytic performance of TiO₂ were investigated. The nanomaterials were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller porosimetry, ultraviolet–visible diffuse reflectance spectroscopy and fluorescent emission spectra. Their photo-catalytic activity was examined by the photodegradation of methylene blue in aqueous solution under both ultra-violet and visible light irradiation. The results show that nitrogen and fluorine co-doped anatase TiO₂ had the characteristics of a smaller crystalline size, broader light absorption spectrum and lower charge recombination than pure TiO₂. Most importantly, more efficient photocatalytic activity under both ultra-violet and visible light was observed. The obtained N–F-TiO₂ nanomaterial shows considerable potential for water treatment under sunlight irradiation.     

Solar photocatalytic decomposition of two azo dyes on multi-walled carbon nanotubes (MWCNTs)/TiO2 composites

Multi-walled carbon nanotubes (MWCNTs)/TiO₂ composite photocatalysts with high photoactivity were prepared by sol-gel process and further characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), and UV-vis absorption spectra. Compared to pure TiO₂, the combination of MWCNTs with titania could cause a significant absorption shift toward the visible region. The photocatalytic performances of the MWCNTs/TiO₂ composite catalysts were evaluated for the decomposition of Reactive light yellow K-6G (K-6G) and Mordant black 7 (MB 7) azo dyes solution under solar light irradiation. The results showed that the addition of MWCNTs enhanced the adsorption and photocatalytic activity of TiO₂ for the degradation of azo dyes K-6G and MB 7. The effect of MWCNTs content, catalyst dosage, pH, and initial dye concentration were examined as operational parameters. The kinetics of photocatalytic degradation of two dyes was found to follow a pseudo-first-order rate law. The photocatalyst was used for seven cycles with photocatalytic degradation efficiency still higher than 98%. A plausible mechanism is also proposed and discussed on the basis of experimental results.     

Photocatalytic degradation of paraquat using nano-sized Cu-TiO2/SBA-15 under UV and visible light

Photocatalytic degradation of paraquat using mesoporous-assembled Cu-TiO₂/SBA15 under UV and visible light was investigated. The catalyst was synthesized by impregnation of Cu-TiO₂ colloids onto SBA-15. The colloids of Cu-TiO₂ were prepared via sol-gel method while the mesoporous support was prepared using hydrothermal technique. The catalyst was characterized using X-ray diffraction, nitrogen adsorption-desorption, transmission electron microscopy, UV diffuse reflectance spectroscopy, Zeta potential and X-ray adsorption spectroscopy. Results from characterizations showed that Cu doped TiO₂ had a small crystalline size and was well-dispersed on SBA-15. The inclusion of SBA-15 significantly enhanced the photocatalytic activity of the catalyst. Among the three types of undoped catalyst in this study (P25, TiO₂, TiO₂/SBA-15), TiO₂/SBA-15 yielded the highest degradation of paraquat for all pH under UV illumination. Meanwhile 2 wt.% Cu-TiO₂/SBA-15 yielded the highest activity under visible light.     

BiOCl/TiO_2复合材料的可见光活性及机理研究

采用水热法和溶胶凝胶法制备新型BiOCl/TiO2复合材料并明确了最优的掺杂比例(2%).随后利用X射线衍射(XRD)、紫外可见漫反射(DRS)、透射电镜(TEM)和X射线光电子能谱(XPS)对该材料进行表征.由于禁带宽度较大,纯BiOCl和TiO2的可见光催化性能极差,然而二者复合后,同条件下的苯降解率却大幅提升,可以达到40%以上.经证实,催化剂制备过程中,Bi的状态发生变化,在TiO2导、价带之间插入新的能级,使其禁带宽度变窄,电子可以实现可见光跃迁.     

Modification of a magnetic carbon composite for ciprofloxacin adsorption

A magnetic carbon composite, Fe₃O₄/C composite, was fabricated by one-step hydrothermal synthesis, modified by heat treatment under an inert atmosphere (N₂), and then used as an adsorbent for ciprofloxacin (CIP) removal. Conditions for the modification were optimized according to the rate of CIP removal. The adsorbent was characterized by Fourier transform infrared spectroscopy, X-ray diffraction measurements, vibrating-sample magnetometry, scanning electron microscopy, transmission electron microscopy, and N₂ adsorption/desorption isotherm measurements. The results indicate that the modified adsorbent has substantial magnetism and has a large specific area, which favor CIP adsorption. The effects of solution pH, adsorbent dose, contact time, initial CIP concentration, ion strength, humic acid and solution temperature on CIP removal were also studied. Our results show that all of the above factors influence CIP removal. The Langmuir adsorption isotherm fits the adsorption process well, with the pseudo second-order model describing the adsorption kinetics accurately. The thermodynamic parameters indicate that adsorption is mainly physical adsorption. Recycling experiments revealed that the behavior of adsorbent is maintained after recycling for five times. Overall, the modified magnetic carbon composite is an efficient adsorbent for wastewater treatment.     

Synthesis and enhanced visible-light responsive of C,N,S-tridoped TiO2 hollow spheres

C,N,S-tridoped TiO2 hollow spheres （labeled as C,N,S-THs） were synthesized using carbon spheres as template and C,N,S-tridoped TiO2 nanoparticles as building blocks. The structure and physicochemical properties of the catalysts were characterized by X- ray diffraction （XRD）, scanning electron microscopy （SEM）, UV-Vis diffuse reflectance spectrum （DRS）, N2 adsorption-desorption isotherms, X-ray photoelectron spectroscopy （XPS） and Photoluminescence emission spectroscopy （PL）. The results showed that the hollow spheres had average diameter of about 200 nm and the shell thickness was about 20 nm. The tridoped TiO2 hollow spheres exhibited strong absorption in the visible-light region. C,N,S-tridoped could narrow the band gap of the THs by mixing the orbit O 2p with C 2p, N 2p and S 3p orbits and shift its optical response from ultraviolet （UV） to the visible-light region. PL analysis indicated that the electron-hole recombination rate of TiO2 hollow spheres had been effectively inhibited when doped with C, N and S elements. The photocatalytic activities of the samples were evaluated for the degradation of X-3B （Reactive Brilliant Red dye, C.I. Reactive Red 2） aqueous solution under visible-light （λ 〉 420 nm） irradiation. It was found that the C,N,S-tridoped TiO2 hollow spheres indicated higher photocatalytic activity than commercial P25 and the undoped counterpart photocatalyst.     

Photocatalytic degradation of methyl orange using ZnO/TiO2 composites

ZnO/TiO₂ composites were synthesized by using the solvothermal method and ultrasonic precipitation followed by heat treatment in order to investigate their photocatalytic degradation of methyl orange (MO) in aqueous suspension under UV irradiation. The composition and surface structure of the catalyst were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), and transmission electron microscopy (TEM). The degradation efficiencies of MO at various pH values were obtained. The highest degradation efficiencies were obtained before 30 min and after 60 min at pH 11.0 and pH 2.0, respectively. A sample analysis was conducted using liquid chromatography coupled with electrospray ionization ion-trap mass spectrometry. Six intermediates were found during the photocatalytic degradation process of quinonoid MO. The degradation pathway of quinonoid MO was also proposed.     

Rubber sheet strewn with TiO2 particles:Photocatalytic activity and recyclability

A new method for the preparation of rubber sheet strewn with titanium dioxide particles (TiO₂-strewn sheet) is presented. This simple and low cost method is based on the use of TiO₂ powder (Degussa P25) being strewn onto the sheet made from rubber latex (60% HA) through a steel sieve. The characteristic of the TiO₂-strewn sheet was studied by using scanning electron microscopy/energy dispersive X-ray spectrometer (SEM/EDS) and X-ray diffractometer (XRD) techniques. The photocatalytic activity of TiO₂-strewn rubber sheet was evaluated using Indigo Carmine (IC) dye as a model for organic dye pollutant in water. The results showed that the TiO₂-strewn sheet could degrade IC dye solution under UV light irradiation. The effects of pH, initial concentration, and the intensity of UV light on the photodegradation were also investigated. Kinetics of the photocatalytic degradation was of the first-order reaction. The used TiO₂-strewn sheet can be recovered and reused. The recycling uses did not require any cleaning between successive uses and no decline in the photodegradation efficiency was observed compared with freshly prepared TiO₂-strewn sheet.     

Tricrystalline TiO2 with enhanced photocatalytic activity and durability for removing volatile organic compounds from indoor air

It is important to develop efficient and economic techniques for removing volatile organic compounds(VOCs) in indoor air. Heterogeneous Ti O_2-based semiconductors are a promising technology for achieving this goal. Anatase/brookite/rutile tricrystalline Ti O_2 with mesoporous structure was synthesized by a low-temperature hydrothermal route in the presence of HNO_3.The obtained samples were characterized by X-ray diffraction and N_2 adsorption–desorption isotherm. The photocatalytic activity was evaluated by photocatalytic decomposition of toluene in air under UV light illumination. The results show that tricrystalline Ti O_2 exhibited higher photocatalytic activity and durability toward gaseous toluene than bicrystalline Ti O_2,due to the synergistic effects of high surface area, uniform mesoporous structure and junctions among mixed phases. The tricrystalline Ti O_2 prepared at R HNO_3= 0.8, containing80.7% anatase, 15.6% brookite and 3.7% rutile, exhibited the highest photocatalytic activity,about 3.85-fold higher than that of P25. The high activity did not significantly degrade even after five reuse cycles. In conclusion, it is expected that our study regarding gas-phase degradation of toluene over tricrystalline Ti O_2 will enrich the chemistry of the Ti O_2-based materials as photocatalysts for environmental remediation and stimulate further research interest on this intriguing topic.     

Synthesis and kinetics investigation of meso-microporous Cu-SAPO-34 catalysts for the selective catalytic reduction of NO with ammonia

A series of meso-microporous Cu-SAPO-34 catalysts were successfully synthesized by a one-pot hydrothermal crystallization method, and these catalysts exhibited excellent NH_3-SCR performance at low temperature. Their structure and physic chemical properties were characterized by means of X-ray diffraction patterns(XRD), Scanning electron microscopy(SEM), Transmission electron microscopy(TEM), N_2 sorption-desorption, nuclear magnetic resonance(NMR), Inductively Coupled Plasma-Atomic Emission spectrometer(ICP-AES), X-ray absorption spectroscopy(XPS),Temperature-programmed desorption of ammonia(NH_3-TPD), Ultraviolet visible diffuse reflectance spectroscopy(UV-Vis DRS) and Temperature programmed reduction(TPR).The analysis results indicate that the high activities of Cu-SAPO-34 catalysts could be attributed to the enhancement of redox property, the formation of mesopores and the more acid sites. Furthermore, the kinetic results verify that the formation of mesopores remarkably reduces diffusion resistance and then improves the accessibility of reactants to catalytically active sites. The 1.0-Cu-SAPO-34 catalyst exhibited the high NO conversion( 90%) among the wide activity temperature window in the range of 150–425℃.     

Pure and Mg-doped self-assembled ZnO nano-particles for the enhanced photocatalytic degradation of 4-chlorophenol

A novel self-assembled pure and Mg doped ZnO nano-particles （NPs） were successfully synthesized by a simple low temperature co-precipitation method. The prepared photocatalysts were characterized by X-ray diffraction, high resolution scanning electron mi- croscopy, high resolution transmission electron microscopy, diffuse reflectance spectroscopy and photoluminescence （PL） spectroscopy. The results indicated that the prepared photocatalysts showed high crystallinity with a uniform size distribution of the NPs. The degradation of cholorphenols is highly mandatory in today＇s scenario as they are affecting the environment adversely. Thus, the photocatalytic degradation of 4-chlorophenol （4-CP）, a potent endocrine disrupting chemical in aqueous medium was investigated by both pure and Mg-doped ZnO NPs under UV-light irradiation in the present study. The influence of the Mg content on the structure, morphology, PL character and photocatalytic activity of ZnO NPs were investigated systematically. Furthermore,the effect of different parameters such as 4-CP concentration, photocatalyst amount, pH and UV-light wavelength on the resulting photocatalytic activity was investigated.     

A simple and cheap method for preparation of coupled ZrO2/ZnO with high photocatalytic activities

The objective of this study was to prepare a new photocatalyst with high activities for degradation of organic pollutants. Coupled ZrO₂/ZnO photocatalyst was prepared with a simple precipitation method with cheap raw materials zinc acetate and zirconium oxychloride, and was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Reactive brilliant red X-3B was used as a model compound to investigate the photocatalytic activity of synthesized catalysts in water under 254 nm UV irradiation. Results show that the optimal calcination temperature and coupling molar ratio of Zr were 350°C And 2.5%, respectively. At the calcination temperature of 350°C, ZrO₂ was dispersed on the surface of hexagonal ZnO in the form of amorphous clusters. The particle size of ZrO₂/ZnO decreased with the decrease of calcination temperature and the increase of Zr coupling amount. ZrO₂/ZnO has better photocatalytic activity for degradation of reactive brilliant red (RBR) X-3B than pure ZnO and P25-TiO₂.