活性炭吸附-微波诱导氧化处理有机废水

研究了化工废水中有机污染物在颗粒活性炭(GAC)上的吸附行为,以及用微波辐照再生活性炭使污染物被诱导氧化的过程.结果表明,污染物在GAC上的吸附动力学为一级过程,修正后的Freundlich 吸附等温线模型能更好地定量描述其吸附过程.再生后活性炭的碘值可以达到900mg·g-1左右,且能耗相对较低.     

微波法不同影响因素对土壤中氯丹降解的影响

以农药生产企业搬迁遗留场地土壤为研究对象,研究了微波修复土壤技术的各影响因素对氯丹降解的影响.结果表明:在土壤含水率20％、pH值8.5、活性炭投加量50 g·kg-1、微波功率600 W和辐照时间20 min条件下,微波法对氯丹去除率达到89％;若土壤中氯丹去除温度保持在300 ℃以上,可使氯丹大幅度去除.各因素对微波法去除氯丹的影响由大到小依次为微波功率、辐照时间、活性炭投加量和含水率.修复过程中氯丹降解的中间产物有六氯、七氯和九氯等,推测其降解过程存在加氯和脱氯反应.     

微波－混凝法处理滇池高藻原水的实验研究

实验采用微波－混凝法处理滇池高藻原水,考察了混凝剂聚合氯化铝（PAC）投加量、进水pH值、微波功率及辐照时间对除藻去浊效果的影响,并与单一混凝的处理效果进行了对比。结果表明：在PAC投加量为80mg／L、进水pH值为8—9、微波功率为600W、辐照时间为1．5min的条件下除藻去浊效果最佳,除藻率达94．4％,剩余浊度可从89NTU降到3NTU左右;微波－混凝法对滇池高藻原水的处理效果明显优于单一混凝,同时可降低混凝剂用量,具有良好的强化混凝效果。     

微波诱导活性炭氧化降解阳离子红GTL废水的特性

采用微波诱导氧化工艺技术,以活性炭为催化剂,对阳离子红GTL染料废水进行氧化处理,考察了活性炭用量、微波功率、反应时间及染料初始质量浓度对阳离子红GTL去除率的影响,利用SEM/EDS、BET表征了反应前后活性炭的结构及组分变化.结果表明:微波和活性炭具有协同效应;在pH=7.0,活性炭用量4 g,阳离子红质量浓度为50 mg·L-1,微波功率300 W,反应时间4 min的条件下,阳离子红GTL去除率达到99.4%;活性炭的结构与组分影响阳离子红GTL的微波处理效果.     

微波辐射技术在聚乙烯醇降解反应中的应用

考察了微波功率、pH值、H2O2用量和反应时间对聚乙烯醇降解反应的影响.实验表明,在微波辐射条件下,微波功率为800W,辐射时间为1min,pH值为3, H2O2用量为22g H2O2·100g-1 PVA时,5ml聚乙烯醇(7%)的平均聚合度能够在1min内降至67.与常规油浴加热相比,反应速度提高10-20倍.     

生石灰与微波协同作用对污泥脱水的影响

采用生石厌与微波协同作用,对广州市猎德污水厂浓缩污泥脱水的影响进行了实验研究.结果表明,单独投加生石灰,加入量为40 g·L-1时,污泥比阻由原来的4.72×1013m·kg-1降至1.9×1013m·kg-1,降低了约96%;单独使用微波调理污泥,在800W功率微波下辐射100s,可使污泥比阻由原来的4.72×101...     

微波诱导改性活性炭催化处理低浓度抗生素废水

通过采用负载FeSO4活性炭、CuSO4活性炭和一般活性炭作为微波催化剂处理抗生素废水的对比实验,研究不同负载方法对抗生素制药废水COD去除的差别,结果表明,负载FeSO4的活性炭作为催化剂的微波处理系统对COD的去除率最高.以微波诱导负载FeSO4的活性炭为催化剂对抗生素制药废水进行处理,结果表明,增大负载FeSO4活性炭质量,微波辐射时间和微波功率,均有利于抗生素废水中COD的去除,但各影响因素的取值并不是越大越好.对微波诱导负载FeSO4活性炭催化工艺处理抗生素废水进行反应动力学分析,结果显示,过程近似一级反应,其动力学方程为:lnC0/C=0.1413t+5.4121,r=0.9876.反应动力学常数为0.1413 min-1.     

活性炭辅助微波热解污泥反应条件的试验研究

针对微波不能直接实现原污水污泥高温热解的问题,采用活性炭作为微波能吸收物质辅助污泥热解。对影响污泥热解效能的3个主要因素：污泥样品量、活性炭掺杂量和微波辐射功率,各做了3个水平的考察,得到了试验条件下的最优方案：污泥样品量30g、活性炭掺杂量6g、微波辐射功率1200W。结果表明：在最优试验方案下,污泥能在7min内升至920℃的高温,实现污泥快速、高效热解。通过分析3个因素对污泥热解效能的影响,进一步对最优试验方案下的固体产物吸收微波的性能及用其作为掺杂物辅助微波热解污水污泥的可行性进行了研究,结果表明：固体残渣吸收微波性能良好,可以代替活性炭作为更经济、高效的污泥微波热解辅助材料。     

微波催化氧化法处理垃圾渗滤液的正交试验

在微波辐射条件下,采用活性炭与Fenton试剂处理垃圾渗滤液,并通过正交试验考察了微波辐射时间、pH、活性炭用量、硫酸亚铁用量和H2O2用量对处理效果的影响.结果表明:pH对处理效果的影响最大,其次为活性炭用量、微波辐射时间、硫酸亚铁用量和H2O2用量;在100 mL水样中,最佳处理条件为活性炭2 g、H2O20.2 mL、硫酸亚铁0.834 g、pH 6、微波辐射时间10 min,垃圾渗滤液中的COD去除率达到75.36%.     

污水污泥微波辅助快速热裂解制生物油和合成气

利用实验室微波加热装置,研究了微波功率、椰壳活性炭(微波受体)添加量和反应气氛条件对污泥(含水率:76.8%)热解产物产量和特性的影响.结果表明,足够的微波辐照强度和7.5%以上的活性炭添加量可实现污泥的快速热裂解.污泥升温速率越快,生物油和合成气的产率越高.快速热裂解过程中生物油的产率超过8.5%,合成气的产率超过8.0%,并且合成气中H2和CO的体积之和超过总气体体积的50%.生物油主要生成于污泥150—250℃升温阶段,合成气主要生成于污泥150—400℃升温阶段.与通空气(少量O2存在条件)相比,氮气气氛更有利于污泥热解生成生物油,并可大幅度降低CO2的生成量,因此有利于合成气品质的提高.     

Microwave enhanced stabilization of copper in artificially contaminated soil

Microwave processing was used to stabilize copper ions in soil samples. Its effects on the stabilization efficiency were studied as a function of additive, microwave power, process time, and reaction atmosphere. The stabilization efficiency of the microwave process was evaluated based on the results of the toxicity characteristic leaching procedure (TCLP) test. The results showed that the optimal experimental condition contained a 700W microwave power, 20 min process time and 3 iron wires as the additive, and that the highest stabilization efficiency level was more than 70%. In addition, the different reaction atmospheres showed no apparent effect on the stabilization efficiency of copper in the artificially contaminated soil. According to the result of the Tessier sequential extraction, the partial species of copper in the contaminated soil was deduced to transform from unstable species to stable states after the microwave process.     

Catalytic decomposition of low level ozone with gold nanoparticles supported on activated carbon

Highly dispersed gold nanoparticles were supported on coal-based activated carbon (AC) by a sol immobilization method and were used to investigate their catalytic activity for low-level ozone decomposition at ambient temperature. Nitrogen adsorption-desorption, scanning electron microscope (SEM), and X-ray photoelectron spectroscopy (XPS) were used to characterize the catalysts before and after ozone decomposition. The results showed that the supported gold nanoparticles prepared with microwave heating were much smaller and more uniformly dispersed on the activated carbon than those prepared with traditional conduction heating, exhibiting higher catalytic activity for ozone decomposition. The pH values of gold precursor solution significantly influenced the catalytic activity of supported gold for ozone decomposition, and the best pH value was 8. In the case of space velocity of 120000h⁻¹, inlet ozone concentration of 50mg/m³, and relative humidity of 45%, the Au/AC catalyst maintained the ozone removal ratio at 90.7% after 2500min. After being used for ozone decomposition, the surface carbon of the catalyst was partly oxidized and the oxygen content increased accordingly, while its specific surface area and pore volume only decreased a little. Ozone was mainly catalytically decomposed by the gold nanoparticles supported on the activated carbon.     

制药废水的可生物降解性与生物毒性研究

制药废水有机物含量高,难生物降解成分多,有些成分可抑制污泥活性或具有生物毒性.以某制药企业维生素生产的7个工段(W1 ～ W7)的排放废水为研究对象,用摇瓶试验评价了各工段废水的可生物降解性能,用瓦勃氏呼吸仪测试了各工段废水对污泥活性的抑制作用,用发光菌急性毒性试验评价了各工段废水经好氧生物处理前后的生物毒性变化.研究...     

4种吸附剂对对氯苯酚的吸附性能

研究了常温（18℃）条件下粉末活性炭（PAC）、颗粒活性炭（GAC）、天然膨润土和天然海泡石4种吸附剂对对氯苯酚（4-CP）的静态吸附规律,考察了投加灭活活性污泥对吸附性能的影响。结果表明：4种吸附剂对4-CP的吸附符合Langmiur和Freundlich吸附等温式,且吻合良好;4种吸附剂对4-CP的饱和吸附量不同,大小顺序为：PAC〉GAC〉天然膨润土〉天然海泡石;灭活活性污泥与4种吸附剂共存时,降低了4种吸附剂对4-CP的吸附能力。     

微波辅助固相顶空-气相色谱法测定人造板材中的苯系物

采用微波辅助固相顶空-气相色谱法测定了人造板材中的苯系物含量,考察了不同微波功率作用下3种苯系物随时间的变化趋势,在优化的条件下测定了3种苯系物的含量.该法检出限为3.6—13.4 ng.g-1板材,RSD为2.7%—9.8%,回收率为86.9%—109.4%,方法简便、快速,适合固体板材中苯系物的直接快速分析.     

Ammonia removal from low-strength municipal wastewater by powdered resin combined with simultaneous recovery as struvite

• Powdered resin was employed for ammonia recovery from municipal wastewater. • Powdered resin achievedefficient ammonia removal under various working conditions. • Co-existing cations indicated competitive adsorption of ammonia. • Ammonia was recoveredby two-stage crystallization coupled with ion exchange. Low-strength municipal wastewater is considered to be a recoverable nutrient resource with economic and environmental benefits. Thus, various technologies for nutrient removal and recovery have been developed. In this paper, powdered ion exchange resin was employed for ammonia removal and recovery from imitated low-strength municipal wastewater. The effects of various working conditions (powdered resin dosage, initial concentration, and pH value) were studied in batch experiments to investigate the feasibility of the approach and to achieve performance optimization. The maximum adsorption capacity determined by the Langmuir model was 44.39 mg/g, which is comparable to traditional ion exchange resin. Further, the effects of co-existing cations (Ca²⁺, Mg²⁺, K⁺) were studied. Based on the above experiments, recovery of ammonia as struvite was successfully achieved by a proposed two-stage crystallization process coupled with a powdered resin ion exchange process. Scanning electron microscopy (SEM) and X-ray diffractometry (XRD) results revealed that struvite crystals were successfully gained in alkaline conditions (pH= 10). This research demonstrates that a powdered resin and two-stage crystallization process provide an innovative and promising means for highly efficient and easy recovery from low-strength municipal wastewater.