Adsorption of atrazine from aqueous solution on heat treated kerolites

The adsorption of 6-chloro-N(2)-ethyl-N(4)-isopropyl-1,3,5-triazine-2,4-diamine (atrazine) on heat treated kerolite samples at 110 degrees C (K-110), 200 degrees C (K-200), 400 degrees C (K-400) and 600 degrees C (K-600) from aqueous solution at 25 degrees C has been studied. The evolution of surface properties of kerolite samples such as specific surface area and porosity after heat treatment was analysed. The clays were characterised by using usual techniques: FTIR spectroscopy, XRD diffraction, TG and DTG analysis, surface analysis and Hg porosimetry. The adsorption experimental data points have been fitted to the Freundlich equation in order to calculate the adsorption capacities (K(f)) of the samples; K(f) values range from 468 mgkg(-1) for the K-110 sample up to 2291 mgkg(-1) for the K-600 sample. The values obtained for the removal efficiency (R), (percentage of pesticide removed), ranged from 48% for K-110 up to 78% for K-600. The adsorption experiments showed that the stronger heat treatment, the most effective adsorption of atrazine, so, as this type of clay is relatively plentiful, these activated samples might be used in order to remove this pesticide from water.     

Adsorption of chloridazon from aqueous solution on modified kerolite-rich materials

The adsorption of chloridazon (5-amine-4-chloro-2-phenylpyridazin-3(2H)-one) on kerolite samples heated at 110 degrees C (K-110), 200 degrees C (K-200), 400 degrees C (K-400), 600 degrees C (K-600) and acid-treated with H(2)SO(4) solutions of two different concentrations (0.25 and 0.5 M) (K-0.25 and K-0.5, respectively) from pure water at 25 degrees C has been studied by using batch and column experiments. The adsorption experimental data points were fitted to the Freundlich equation in order to calculate the adsorption capacities (K(f)) of the samples; K(f) values ranged from 184.7 mg kg(-1) (K-0.5) up to 2253 mg kg(-1) (K-600). This indicated that the heat treatment given to the kerolite greatly increases its adsorption capacity for the herbicide whereas the acid treatment produces a clear decrease in the amount of chloridazon adsorbed. The removal efficiency (R) was also calculated; R values ranging from 52.8% (K-0.5) up to 88.3% (K-600). Thus, the results showed that the 600 degrees C heat-treated kerolite was more effective in relation to adsorption of chloridazon and it might be reasonably used in removing this herbicide from water.     

Adsorption behavior of 2,4-dichlorophenol and pentachlorophenol in an allophanic soil

The adsorption of 2,4-dichlorophenol (2,4-DCP) and pentachlorophenol (PCP) by a variable-charge soil from southern Chile was studied in a series of batch equilibration experiments. 2,4-DCP and PCP adsorption behavior was evaluated as a function of pH (pH values of 4.5, 6.0 and 7.5) in a 0.1M KCl (25 degrees C) background solution for soil material collected at three different depths (0-20 cm, 20-40 cm, and 40-60 cm). 2,4-DCP and PCP adsorption decreased with increasing soil pH, suggesting that the undissociated species were adsorbed more readily and that electrostatic repulsion may inhibit partitioning as pH increases. The PCP adsorption was greater than observed for 2,4-DCP and decreased with soil depth. Multiple regression analysis between K(d) and various soil properties indicated that the soil organic carbon content is a strong indicator of chlorophenol adsorption, and in addition to organic carbon, the soil pH is an important property controlling adsorption behavior.     

Melamine-based organoclay to sequester atrazine

Sequestration of aqueous atrazine by organoclays prepared from the surfactant 6-piperazin-1-yl-N,N'-bis-(1,1,3,3-tetramethyl-butyl)-(1,3,5)triazine-2,4-diamine and Gonzales bentonite was assessed using 14C-labeled atrazine. Organoclays with varying ratios of surfactant to clay were evaluated with respect to their ability to sequester atrazine from an aqueous solution. Organoclays containing 100-200 g kg-1 surfactant on a total weight basis provided the most efficient adsorption of atrazine, with apparent KOC values exceeding 5000 l kg-1 at these loading fractions. Less than 12% of sequestered atrazine was released during four sequential day long washings, supporting our expectation that the majority of the reaction of atrazine with the surfactant lead to irreversible chemical bond formation through nucleophilic aromatic substitution.     

Adsorption of chloridazon from aqueous solution on modified kerolite-rich materials

The adsorption of chloridazon (5-amine-4-chloro-2-phenylpyridazin-3(2H)-one) on kerolite samples heated at 110°C (K-110), 200°C (K-200), 400°C (K-400), 600°C (K-600) and acid-treated with H₂SO₄ solutions of two different concentrations (0.25 and 0.5 M) (K-0.25 and K-0.5, respectively) from pure water at 25°C has been studied by using batch and column experiments. The adsorption experimental data points were fitted to the Freundlich equation in order to calculate the adsorption capacities (K_f) of the samples; K_f values ranged from 184.7 mg kg^?1 (K-0.5) up to 2253 mg kg^?1 (K-600). This indicated that the heat treatment given to the kerolite greatly increases its adsorption capacity for the herbicide whereas the acid treatment produces a clear decrease in the amount of chloridazon adsorbed. The removal efficiency (R) was also calculated; R values ranging from 52.8% (K-0.5) up to 88.3% (K-600). Thus, the results showed that the 600°C heat-treated kerolite was more effective in relation to adsorption of chloridazon and it might be reasonably used in removing this herbicide from water.     

Effect of dye compounds on the adsorption of atrazine by natural sediment

The overall objective of this research is to investigate competitive adsorption between atrazine (AT) and dye compounds in the natural aquatic sediment. The sorbent was sediment obtained from Guanting Reservoir (Beijing, China), which contained 25% sand, 67% silt, 8% clay, and 2.06% organic carbon. Batch adsorption experiments were conducted at various Ca2+ concentration, pH levels, temperatures, and introducing conditions of dye compounds. Compared with the dye-free system, both of dyes including Congo red (CR) and methylene blue (MB) reduce the adsorption of atrazine over the range of dye concentrations examined, with the adsorption percentage of atrazine decreasing about 14-30%. And the competition between AT and MB is much stronger than that between AT and CR. The adsorption experimental data points have been fitted to the Freundlich equation in order to calculate the adsorption capacities (Kf) of the samples; Kf values range from 1.669 micromol/kg for the MB-AT sample up to 3.738 micromol/kg for the AT-alone sample. By contrast with the single-solute adsorption isotherm, both simultaneous adsorption and dye preloading inhibit the adsorption of atrazine. As for AT preloading, the impacts of CR and MB are different on the desorption of atrazine. As compared to the atrazine desorption without dye compounds, a certain amounts of atrazine molecules are replaced by MB in AT preloading system, while in CR solution AT is adsorbed strongly on the sediment and could not be replaced by CR. The result suggests that micropore constriction by CR reduces the desorption rate of atrazine.     

Salting-in and salting-out effects of ionic and neutral osmotica on limonene and linalool Henry's law constants and octanol/water partition coefficients

Foliar emission rates of plant-generated volatile monoterpenes depend on monoterpene partitioning between air, aqueous and lipid-phases in the leaves. While Henry's law constants (H pc, equilibrium gas/water partition coefficient) and octanol/water partition coefficients (K OW) for pure water have been previously used to simulate monoterpene emissions from the leaves, aqueous phase in plants is a complex solution of electrolytes and neutral osmotica. We studied the effects of dissociated compounds KCl and glycine and sugars glucose, sorbitol and sucrose with concentrations between 0 and 1M on H pc and K OW values for limonene and linalool. Linalool with ca. 1500-fold lower H(pc) (2.62 Pa m(3)mol(-1) for pure water at 30 degrees C) and ca. 30-fold lower K OW (955 mol mol(-1) for pure water at 25 degrees C) is the more hydrophilic compound of the two monoterpenes. H pc of both monoterpenes increased with increasing concentration of both ionic compounds and sorbitol, but decreased with increasing glucose and sucrose concentrations. The salting-out coefficients for H pc (kH) were ca. an order of magnitude larger for more hydrophilic compound linalool than for more hydrophobic limonene. For linalool, co-solutes modified H pc by 30-50% at the highest concentration (1M) tested. The effect of temperature on the salting-out coefficient of KCl was minor. As with H pc, K OW increased with increasing the concentration of KCl, glycine and sorbitol, and decreased with increasing glucose and sucrose concentrations. For limonene, co-solutes modified K OW by 20-50% at the highest concentration used. For linalool, the corresponding range was 10-35%. Salting-out coefficients for H pc and K OW were correlated, but the lipid-solubility was more strongly affected than aqueous solubility in the case of limonene. Overall, these data demonstrate physiologically important effects of co-solutes on H pc and K OW for hydrophilic monoterpenes and on K OW for hydrophobic monoterpenes that should be included in current emission models.     

Effect of surfactants at low concentrations on the sorption of atrazine by natural sediment.

A series of experiments were carried out to determine the effect of surfactants at low concentrations on the sorption of atrazine by natural sediments. With surfactant concentrations ranging from 0 to 20 mg/ L, anionic and cationic surfactants appreciably reduce the adsorption of atrazine, while nonionic surfactant decreases the adsorption of atrazine at concentrations equal to or less than 1 mg/L and increases adsorption at higher concentrations. Desorption of atrazine in the presence of different sodium dodecylbenzene sulfonate (SDBS) concentrations shows that a portion of the bound pesticide resists desorption in the SDBS free system. However, the addition of SDBS accelerates the desorption of atrazine. Furthermore, the nature of sediment and the contacting sequence of SDBS, at 10 mg/L, with the sediment, also influence the adsorption of atrazine. The conclusions in this study could be explained partially by the effect of the type and concentration of surfactants and the characteristics of sediments.     

Lack of effects of atrazine on estrogen-responsive organs and circulating hormone concentrations in sexually immature female Japanese quail (Coturnix coturnix japonica)

The widely used herbicide, atrazine, has been reported to exhibit reproductive toxicity in rats and amphibians. The present studies investigate toxicity of atrazine in Japanese quail and its ability to influence reproduction in sexually immature females. Atrazine was administered in the diet at concentrations from 0.001 to 1000 ppm (approximately 109 mg kg-1 per day) or systemically via daily subcutaneous injections (1 and 10 mg kg-1) or Silastic implants. Atrazine did not cause overt toxicity in sexually immature female quail (no effects on change in body weight, feed intake, mortality or on circulating concentrations of the stress hormone, corticosterone). It was hypothesized that if atrazine were to have estrogenic activity or to enhance endogenous estrogen production, there would be marked increases in the weights of estrogen sensitive tissues including the oviduct, the liver and the ovary together with changes in gonadotropin secretion. However, atrazine had no effect on either liver or ovary weights. Atrazine in the diet increased oviduct weights at 0.1 and 1 ppm in some studies. These effects were not consistently observed and were not significant when data from studies were combined. Systemic administration of atrazine had no effect on oviduct weights. Dietary (concentrations from 0.001 to 1000 ppm) and systemically administered atrazine had no effect on circulating concentrations of luteinizing hormone (LH). The present studies provide evidence for a lack of general or reproductive toxicity of atrazine in birds.     

The toxicity and bioavailability of atrazine and molinate to Chironomus tepperi larvae in laboratory and river water in the presence and absence of sediment

Acute (10 day) semi-static toxicity tests in which the midge, Chironomus tepperi, were exposed to atrazine and molinate were conducted in laboratory water and in river water, in the absence and presence of sediment. The bioavailability measured as median lethal concentrations (LC50) and 95% fiducial limits (FLs) of atrazine to C. tepperi in laboratory water in the absence and presence of sediment were 16.6 (14.3-19.4) and 21.0 (18.2-24.1) mg l(-1), respectively while the corresponding values in river water were 16.7 (14.7-19.0) and 22.7 (20.3-25.4) mg l(-1), respectively. For molinate, the LC50 and FL values in laboratory water in the absence and presence of sediment were 8.8 (6.8-11.4) and 14.3 (12.4-16.4) mg l(-1), respectively and the corresponding values in river water were 9.3 (7.6-11.3) and 14.5 (12.4-16.9) mg l(-1), respectively. Atrazine has low toxicity (LC50 > 10 mg l(-1)) while molinate has moderate toxicity (1 mg l(-1) < LC50 < 10 mg l(-1)) to C. tepperi. River water did not significantly (P > 0.05) reduce the bioavailability of either chemical to C. tepperi. However, the presence of sediment did significantly (P < 0.05) reduce the bioavailability of both atrazine and molinate to C. tepperi.     

Effect of density-driven flow on the through-diffusion experiment

Diffusion is one of the main mechanisms of solute transport in pore water of geologic media. The effective diffusion coefficient of a solute in a rock is usually measured by the through-diffusion experiment. However, in this experiment, the effect of advection, induced by density difference between dense aqueous solution and pure water, has not been considered. To evaluate the effect of density-driven flow, a through-diffusion experiment using Fontainebleau sandstone was conducted for KCl and KI aqueous solutions with various densities. The measured effective diffusion coefficients were positively correlated with the density difference; the effective diffusion coefficient of a 1 M KI solution (density difference, 0.119 g/cm³) was one order of magnitude larger than that of a 0.1 M KCl solution (density difference, 0.005 g/cm³). The result is explained by a theoretical model using a diffusion–advection equation including Darcy's law. Based on the theory, a diagram to evaluate the condition at which the measured effective diffusion coefficient does not include the effect of advection is presented.     

Crystalline hydrous ferric oxide: an adsorbent for chromium(VI)-contaminated industrial wastewater treatment.

Synthetic crystalline hydrous ferric oxide (CHFO) (particle size 0.14 to 0.29 mm) has been used systematically for adsorptive chromium(VI) removal from contaminated water. Batch experiments were performed as a function of pH, contact time, solute concentration, and regeneration of adsorbents. Column experiments were performed for breakthrough points in the presence and absence of other ions and treatment of industrial effluent. The optimum pH range was 2.0 to 4.0. The adsorption kinetic data could be described well by both second-order and pseudo-first-order models. The isotherm adsorption data at 30 +/- 2 degrees C obeyed the Langmuir model best. The monolayer adsorption capacity was 35.7 mg/g. Chromium(VI)-rich CHFO could be regenerated up to 89 +/- 1% with 2.0 M sodium hydroxide. Regenerated column reuse showed a decrease (10 to 12%) in breakthrough capacity. Finally, the CHFO- (dried at 300 degrees C) packed column was used for the recovery (98.5 +/- 1.0%) of chromium(VI) from contaminated industrial waste effluent of Hindustan Motor Limited (Hooghly, West Bengal, India).     

Adsorption characteristics of 2,4-dichlorophenoxyacetic acid (2,4-D) from aqueous solution on powdered activated carbon

The removal of 2,4-dichlorophenoxyacetic acid (2,4-D), one of the most commonly used phenoxy acid herbicides, from aqueous solution was studied by using acid-washed powdered activated carbon (PAC) as an adsorbent in a batch system. Adsorption equilibrium, kinetics, and thermodynamics were investigated as a function of initial pH, temperature, and initial 2,4-D concentration. Powdered activated carbon exhibited the highest 2,4-D uptake capacity of 333.3 mg g(-1) at 25 degrees C and an initial pH value of 2.0. Freundlich, Langmuir, and Redlich-Peterson isotherm models were used to express the equilibrium data of 2,4-D depending on temperature. Equilibrium data fitted very well to the Freundlich equilibrium model in the studied concentration range of 2,4-D at all the temperatures studied. Three simplified models including pseudo-first-order, pseudo-second-order, and saturation-type kinetic models were used to test the adsorption kinetics. It was shown that the adsorption of 2,4-D on PAC at 25, 35, and 45 degrees C could be best fitted by the saturation-type kinetic model with film and intraparticle diffusions being the essential rate-controlling steps. The activation energy of adsorption (EA) was determined as--1.69 kJ mole(-1). Using the thermodynamic equilibrium coefficients obtained at different temperatures, the thermodynamic constants of adsorption (deltaG degrees, deltaH degrees, and deltaS degrees) were also evaluated.     

Investigation on the influence of methanol on adsorption and leaching of pesticides with soil column liquid chromatography

The effect of methanol of low concentration on adsorption and leaching of atrazine and tebuconazole was studied in this paper. The adsorption coefficients and the retardation factors (R^m) of pesticides on EUROSOIL 3# log-linearly decreased as volumetric fraction of methanol (f^c) was increased in the binary solvent mixtures of methanol and water. These data are consistent with solvophobic theory formerly outlined for describing the adsorption and transport of hydrophobic organic chemicals from mixed solvents. Nevertheless, the adsorption of these pesticides in soil–water system slightly increased when the soil was pre-washed with methanol in comparison with that pre-washed with water (pure water system). Furthermore, their adsorption coefficients were still higher in binary solvent systems with methanol of very low concentrations, i.e. f^c<0.03 for atrazine and f^c<0.01 for tebuconazole, than those in pure water system. The adsorption coefficients (logK^w) of atrazine and tebuconazole predicted by solvophobic theory were 0.5792 and 1.6525, respectively, and their experimental logK^w were 0.3701 and 1.6275 in pure water system. Obviously, the predicted logK^w of the two pesticides was higher than the experimental log K^w in pure water system. The predicted K^w and the retardation factor (R^w) in pure water system by solvophobic theory are thus possibly inaccurate.     

Mobility of atrazine from alginate-bentonite controlled release formulations in layered soil

The mobility of atrazine [6-chloro-N2-ethyl-N4-isopropyl-1,3,5-triazine-2,4-diamine] from alginate-bentonite-based controlled release (CR) formulations was investigated by using soil columns. Two CR formulations based on sodium alginate (14.0 g kg(-1), atrazine (6.0 g kg(-1), natural or acid-treated bentonite (50 g kg(-1), and water (924 g kg(-1) were compared to technical grade product and commercial liquid (CL) formulation (Gesaprim 500FW). All herbicide treatments were applied to duplicate layered bed systems simulating the typical arrangement under a plastic greenhouse, which is composed of sand (10 cm), peat (2 cm), amended soil (20 cm) and native soil (20 cm). The columns were leached with 39 cm (1500 ml) and 156 cm (6000 ml) of 0.02 M CaCl2 solution to evaluate the effect of water volume applied on herbicide movement. When 39 cm of 0.02 M CaCl2 solution was applied, there was no presence of herbicide in the leachate for the alginate-bentonite CR treatments. However, 0.11% and 0.14% of atrazine appeared in the leachate when the treatment was carried out with technical grade and CL formulations, respectively. When 156 cm of 0.02 M CaCl2 solution was applied, the use of the alginate-acid treated bentonite CR formulation retards and reduces the presence of atrazine in the leachate as compared to technical product. Analysis of the soil columns showed the highest atrazine concentration in the peat layer. Alginate-bentonite CR formulations might be an efficient system for reducing atrazine leaching in layered soil and thus, it could reduce the risks of pollution of groundwater.     

Effect of temperature on the disappearance of four triazine herbicides in environmental waters

The influence of temperature on the disappearance of four s-triazine herbicides, terbuthylazine, simazine, atrazine and prometryn was studied in sea, river and groundwaters spiked with approx. 5 mg l(-1) of each during long-term laboratory incubation. Residues were analyzed by GC-NPD and confirmed by GC-MSD. No clean-up was necessary and a micro on-line method for the determination of herbicide residues was used. The results showed that temperature had little effect on the behaviour of the four herbicides in river and seawaters but strongly affected their behaviour in groundwater. Simazine was the most readily affected compound in sea, river and groundwaters, while terbuthylazine and atrazine were the most persistent in all cases, especially in riverwater. Half-lives ranged from 41 days (constant rate = 0.017 days(-1)) to 196 days (constant rate = 0.003 days(-1)) for simazine (40 degrees C) and terbuthylazine (20 degrees C), respectively, in riverwater. Only for terbuthylazine in riverwater was the remaining percentage at the end of the experiment higher than 50% (58%, 3.21 mg l(-1)). In the other cases, the remaining percentage varied from 4% (0.20 mg l(-1), 40 degrees C) to 43% (2.25 mg l(-1), 20 degrees C) for simazine and terbuthylazine, respectively, in groundwater.     

Studies on the adsorption and kinetics of photodegradation of a model compound for heterogeneous photocatalysis onto TiO(2)

An investigation was made on the adsorption and kinetics of photodegradation of potassium hydrogenphthalate in an aqueous suspension of TiO(2). Two models, Langmuir and Freundlich, were used to describe the adsorption process and the model proposed by Langmuir-Hinshelwood (L-H) was employed to describe the kinetics of the photodecomposition reactions of hydrogenphthalate. The results of the adsorptions were fitted to the models proposed by Langmuir and Freundlich. Adsorption was found to be a function of the temperature, with adsorption capacity increasing from 2.4 to 4.5 mg/g when the temperature rose from 20 to 30 degrees C. The kinetic model indicates that the rate constant, k, of the first order reaction, is high in the 10.0 to 100 mg/l interval, which is coherent with the low value of the adsorption constant, K. The results fitted to the L-H model led to an equation that, within the range of concentrations studied here, theoretically allows one to evaluate the photodegradation rate.     

Atrazine sorption and fate in a Ultisol from humid tropical Brazil

This study combined laboratory based microcosm systems as well as field experiments to evaluate the mobility of atrazine on a Ultisol under humid tropical conditions in Brazil. Results from sorption experiments fit to the Freundlich isotherm model [K(f) 0.99 mg kg(-1)/(mg l(-1))(1/n)], and indicate a low sorption capacity for atrazine in this soil and consequently large potential for movement by leaching and runoff. Microcosm systems using (14)C-atrazine to trace the fate of the applied herbicide, showed that 0.33% of the atrazine was volatilized, 0.25% mineralized and 6.89% was recorded in the leachate. After 60 d in the microcosms, 75% of the (14)C remained in the upper 5 cm soil layer indicating atrazine or its metabolites remained close to the soil surface. In field experiments, after 60 d, only 5% of the atrazine applied was recovered in the upper soil layers. In the field experiments atrazine was detected at a depth of 50 cm indicating leaching. Simulating tropical rain in field experiments resulted in 2.1% loss of atrazine in runoff of which 0.5% was adsorbed onto transported soil particles and 1.6% was in solution. Atrazine runoff was greatest two days after herbicide application and decreased 10 fold after 15 d. The use of atrazine on Ultisols, in the humid tropics, constitutes a threat to water quality, causing surface water and ground water pollution.     

Wet peroxide degradation of atrazine

The high temperature (150-200 degrees C), high pressure (3.0-6.0 MPa) degradation of atrazine in aqueous solution has been studied. Under these extreme conditions atrazine steadily hydrolyses in the absence of oxidising agents. Additionally, oxygen partial pressure has been shown not to affect atrazine degradation rates. In no case mineralisation of the parent compound was observed. The addition of the free radical generator hydrogen peroxide to the reaction media significantly enhanced the depletion rate of atrazine. Moreover, partial mineralisation of the organics was observed when hydrogen peroxide was used. Again, oxygen presence did not influence the efficiency of the promoted reaction. Consecutive injections of hydrogen peroxide throughout the reaction period brought the total carbon content conversion to a maximum of 65-70% after 40 min of treatment (suggesting the total conversion of atrazine to cyanuric acid). Toxicity of the effluent measured in a luminometer decreased from 93% up to 23% of inhibition percentage. The process has been simulated by means of a semi-empirical model.     

Sorptive behavior of sorgoleone in ultisol in two solvent systems and determination of its lipophilicity

Sorgoleone (SGL) exuded by sorghum roots inhibits the development of some weeds. Due to its high hydrophobicity, it is expected that SGL presents low soil mobility and limited allelopathic activity in the field. This work aims to evaluate the sorptivity of sorgoleone in octanol-water and in soil under two solvent systems. The two solvent systems were methanol:water (60:40) (MeOH:H2O) and pure methanol (MeOH). These two solvent systems promote different conditions for SGL solubility. Treatments were arranged in a 2 x 6 factorial (solvent systems x equilibrium concentrations in the solution (EC)). For each solvent, the sorption was achieved by shaking 500 mg of soil with 10 ml of 0, 5, 10, 15, 25, 40, and 60 mg L-1 of SGL solution, during 24 h. After centrifugation, the supernatant was filtered and the SGL concentration was determined by high performance liquid chromatography (HPLC). Data of sorbed amount of SGL were submitted to variance analysis, using a hierarchic factorial model. The data of sorbed amount (x/m) and equilibrium concentration (C) were fitted to the linear (x/m = a + KdC) and to the Freundlich (x/m = KfC1/n) models. The isotherm obtained for the MeOH:H2O system presented linear shape, whereas for the MeOH system a two subsequent linear isotherm was fitted. Sorgoleone is a highly hydrophobic compound, presenting a log Kow of 6.1. The sorption of sorgoleone to the soil was very high. The organic environment stimulated the sorgoleone sorption to the soil.