Effects of Diisocyanate and Polymeric Epoxidized Chain Extenders on the Properties of Recycled Poly(Lactic Acid)

Increasing demand in the use of poly(lactic acid) (PLA) leads to a debate about using potential foodstuffs for plastic production and a moral issue when starvation problem is taken into account. One of the solutions is recycling of PLA; however, recycling results in property losses during melt processing due to low thermal stability of PLA. This study focuses on using chain extenders to offset thermal degradation of recycled PLA. The effects of a diisocyanate and a polymeric epoxidized chain extender on the properties of the recycled poly(lactic acid) were investigated. In order to mimic the recycling process, PLA was subjected to thermo-mechanical degradation using a laboratory scale compounder. Chain extender type, loading and mixing time were investigated. On-line rheology and intrinsic viscosity measurements of PLA before and after chain extension confirmed that the molecular weight increased. Dynamic mechanical analysis, rheology and tensile tests revealed that the chain extenders led to a significant increase in modulus, strength and melt-viscosity. It was found that diisocyanate had slightly higher and faster chain extension reactivity than polymeric extender. Differential scanning calorimetry results showed an increase in the crystallization temperature due to the branched and extended chain structure.     

Effects of Compatibilizer and Thermoplastic Starch (TPS) Concentration on Morphological,Rheological, Tensile,Thermal and Moisture Sorption Properties of Plasticized Polylactic Acid/TPS Blends

The blends of polylactic acid plasticized with acetyl tributyl citrate (P-PLA) and thermoplastic wheat starch (TPS) were prepared by a co-rotating twin screw extruder and the effect of maleic anhydride grafted PLA (PLA-g-MA) content as reactive compatibilizer on blends compatibility through morphological, rheological and tensile properties of the blends was investigated. Considerable improvement in properties of P-PLA/TPS (70/30 w/w) blend with incorporating the optimum PLA-g-MA content of 4 phr was achieved as this blend exhibited better morphological and rheological properties with an increase by 158 and 276% in tensile strength and elongation at break, respectively, compared to the uncompatibilized blend. Also the thermal stability and moisture sorption properties of the blends as effected by TPS content were studied. Decreasing in thermal stability and increasing in equilibrium moisture content of the blends were observed with progressively increasing of TPS content. For prediction the moisture sorption behaviour of blends with various TPS contents at different relative humidity, the moisture sorption isotherm data were modeled by GAB (Guggenheim–Anderson–de Boer) model.     

Physicochemical Properties of Composite Materials Based on Thermoplastic Yam Starch and Polylactic Acid Improved with the Addition of Epoxidized Sesame Oil

Journal of Polymers and the Environment - Biodegradable materials provide a primary function in preserving and protecting food products, helping to extend shelf life. The present work aims to...     

Effect of Oxidized Starch on Morphology,Rheological and Tensile Properties of Low-Density Polyethylene/Linear Low-Density Polyethylene/Thermoplastic Oxidized Starch Blends

In this work, morphology, rheological and tensile properties of low-density polyethylene/linear low-density polyethylene/thermoplastic oxidized starch (LDPE/LLDPE/TPOS) blends are studied. The blends of LDPE/LLDPE (70/30, w/w) containing 0–20 wt% TPOS in the presence of 3 wt% of PE-grafted maleic anhydride (PE-g-MA) as a compatibilizer are prepared by a twin screw extruder and then converted to appropriate thin films using an extrusion film blowing machine. Scanning electron microscopic images show that there is a relative good dispersion of oxidized starch particles in PE matrices. However, as TPOS content in the blends increases, the starch particle size increases too. The rheological analyses indicate that TPOS can decrease the elasticity and viscosity of the blends. The LDPE/LLDPE/TPOS blends show power-law behavior and as the TPOS content increases the power-law exponent (n) and consistency index (K) decrease. The ultimate tensile strength and elongation at break of the final blend films reduce, when TPOS content increases from 5 to 20 wt%. However, the required mechanical properties for packaging applications are achieved when 10 wt% oxidized starch is added, according to ASTM D4635.     

Thermoplastic Starch (TPS)/Polylactic Acid (PLA) Blending Methodologies: A Review

Polylactic acid (PLA) and thermoplastic starch (TPS) are biodegradable polymers of biological origin, and the mixture of these polymers has been studied due to the desirable mechanical properties of PLA and the low processing cost of TPS. However, the TPS/PLA combination is thermodynamically immiscible due to the poor interfacial interaction between the hydrophilic starch granules and the hydrophobic PLA. To overcome these limitations, researchers studied the modification, processing, and properties of the mixtures as a strategy to increase the compatibility between phases. This review highlights recent developments, current results, and trends in the field of TPS/PLA-based compounds during the last two decades, with the main focus of improving the adhesion between the two components. The TPS/PLA blends were classified as plasticized, compatible, reinforced and with nanocomposites. This article presents, based on published research, TPS/PLA combinations, considering different methods with significant improvements in mechanical properties, with promising developments for applications in food packaging and biomedicine.

     

Effect of Agar and Cotton Fiber on Properties of Thermoplastic Waxy Rice Starch Composites

Biodegradable polymer from thermoplastic waxy rice starch (TPWRS) was prepared by internal mixer and compression molding. Since tensile properties and water uptake of the TPWRS was still the main disadvantages, the TPWRS sample was, therefore, modified by agar and/or cotton fibers. The effect of different ratios of agar:cotton fibers on properties of the TPWRS matrix were also studied. It was found that new hydrogen bonds could be found for the TPWRS matrix with the addition of different ratios of agar: cotton fibers by the detection of IR peak shift. Tensile properties of the TPWRS sample were significantly improved by the addition of agar or cotton fibers and the highest tensile properties were obtained from the TPWRS composite modified with 4:6 agar:cotton fibers. In addition, thermal degradation temperature and thermal stability of the starch were improved by the incorporation of agar and/or cotton fibers. Moreover, color measurement, morphology, water uptake and biodegradability from soil burial test were also examined.     

Poly(Ethylene Glycol) as a Compatibilizer for Poly(Lactic Acid)/Thermoplastic Starch Blends

A new route to prepare poly(lactic acid) (PLA)/thermoplastic starch (TPS) blends is described in this work using poly(ethylene glycol) (PEG), a non-toxic polymer, as a compatibilizer. The influence of PEG on the morphology and properties of PLA/TPS blends was studied. The blends were processed using a twin-screw micro-compounder and a micro-injector. The morphologies were analyzed by scanning and transmission electron microscopies and the material properties were evaluated by dynamic-mechanical, differential scanning calorimetry, thermogravimetric analysis and mechanical tests. PLA/TPS blends presented large TPS phase size distribution and low adhesion between phases which was responsible for the lower elastic modulus of this blend when compared to pure PLA. The addition of PEG resulted in the increase of PLA crystallization, due to its plasticizing effect, and improvement of the interfacial interaction between TPS and PLA matrix. Results show that incorporation of PEG increased the impact strength of the ternary blend and that the elastic modulus remained similar to the PLA/TPS blend.     

Biodegradability and Thermal Properties of Novel Natural Rubber/Linear Low Density Polyethylene/Thermoplastic Starch Ternary Blends

This work aimed to prepare biodegradable thermoplastic elastomers based on NR/LLDPE/TPS ternary simple blends to achieve some exclusive properties, i.e., good biodegradability in terms of water absorption and weight loss after burial, together with reasonable mechanical and thermal properties. A comparative study on biodegradability and other related properties of NR/LLDPE binary and NR/LLDPE/TPS ternary blends was performed. It was found that increasing the TPS proportion decreased storage modulus and complex viscosity. In addition, the size of dispersed TPS domains in the NR/LLDPE co-continuous matrix increased with TPS proportion, while the mechanical properties in terms of 100% moduli, tensile strength, elongation at break, and hardness decreased. This might be attributed to decreased interfacial adhesion with increasing size of TPS domains. Furthermore, increasing the TPS loading in the blend reduced the temperatures for 5 or 50% mass loss (T₅ or T₅₀) and the degradation temperature (T _d ). However, the biodegradability improved, in terms of increased water absorption and weight loss after burial in soil, with the loading level of TPS.     

Effect of Hydrothermal Polylactic Acid Degradation on Polymer Molecular Weight and Surface Properties

In the present work, polylactic acid, PLA, samples were degraded by hydrothermal treatment, and then their molecular weights, crystallinity, surface charges and compositions, were determined, respectively, by using viscometry, ¹H NMR, Differential Scanning Calorimetry (DSC), microelectrophoresis and Infra Red spectroscopy methods. The viscometry and ¹H NMR data indicate that the molecular weight, of the polymer, decreases after the hydrothermal treatment. However, the crystalline fractions of the PLA samples, as obtained from the DSC and X-ray data, were not altered after the hydrothermal treatment. Furthermore, the zeta potential data, as determined by microelectrophoresis, show for both non-degraded and degraded PLA, an increase of the polymer surface charge density with the pH of the aqueous phase. However, at acidic pH values, the surface charge density for the degraded PLA was higher as compared to the non degraded one. These differences in surface charge densities of the PLA samples were confirmed by Infrared study, according to which the spectra of degraded polymer show the appearance of carboxyl groups occurring at 1,600 cm⁻¹ at the polymer surface.     

Functional Properties of Extruded Starch Acetate Blends

Starch acetate, with degree of substitution of 2, was blended with 0, 7.5 and 15% polylactic acid (PLA), Eastar Bio Copolyester 14766 (EBC) or Mater-Bi ZF03U (MBI) and 10%, 13%, or 16% (d.b.) ethanol and twin-screw extruded at 160°C barrel temperature. Physical characteristics of the extrudates, such as radial expansion ratio, unit and bulk densities, and of the mechanical properties, including unit spring index and bulk spring index, were measured. Type of polymer, polymer content, and ethanol content significantly affected the physical characteristics and mechanical properties. The sample extruded with 7.5% PLA and 13% ethanol had the highest expansion ratio and bulk spring index. The sample with 15% MBI and 16% ethanol had the lowest unit density, while the sample with 7.5% PLA and 16% ethanol had lowest bulk denisty. The highest unit spring index was expressed in the sample containing 7.5% PLA and 10% ethanol.     

Microstructural and Physical Properties of Thermoplastic Corn Starch/Polystyrene Blend Foams Affected by Different Contents and Combinations of Plasticizers

Journal of Polymers and the Environment - A comprehensive study was performed on thermoplastic corn starch (TPS)/polystyrene (PS) blend foam to optimize the formulation from the aspects of...     

Comparison of Polylactic Acid/Kenaf and Polylactic Acid/Rise Husk Composites: The Influence of the Natural Fibers on the Mechanical, Thermal and Biodegradability Properties

This paper investigates and compares the performances of polylactic acid (PLA)/kenaf (PLA-K) and PLA/rice husk (PLA-RH) composites in terms of biodegradability, mechanical and thermal properties. Composites with natural fiber weight content of 20% with fiber sizes of less than 100 μm were produced for testing and characterization. A twin-screw extrusion was used to compound PLA and natural fibers, and extruded composites were injection molded to test samples. Flexural and Izod impact test, TGA, soil burial test and SEM were used to investigate properties. All results were compared to a pure PLA matrix sample. The flexural modulus of the PLA increased with the addition of natural fibers, while the flexural strength decreased. The highest impact strength (34 J m⁻¹), flexural modulus (4.5 GPa) and flexural strength (90 MPa) were obtained for the composite made of PLA/kenaf (PLA-K), which means kenaf natural fibers are potential to be used as an alternative filler to enhance mechanical properties. On the other hand PLA-RH composite exhibits lower mechanical properties. The impact strength of PLA has decreased when filled with natural fibers; this decrease is more pronounced in the PLA-RH composite. In terms of thermal stability it has been found that the addition of natural fibers decreased the thermal stability of virgin PLA and the decrement was more prominent in the PLA-RH composite. Biodegradability of the composites slightly increased and reached 1.2 and 0.8% for PLA-K and PLA-RH respectively for a period of 90 days. SEM micrographs showed poor interfacial between the polymer matrix and natural fibers.     

Effect of Cotton Fiber Contents and Lengths on Properties of Thermoplastic Starch Composites Prepared from Rice and Waxy Rice Starches

Biodegradable polymer was prepared as thermoplastic starch (TPS) using rice and waxy rice starches. In order to increase mechanical properties and reduce water absorption of the TPS, cotton fiber was incorporated as the fiber reinforcement into the TPS matrix. The effect of cotton fiber contents and lengths on properties of the TPS was examined. Internal mixer and compression molding machine were used to mix and shape the samples. It was found that the thermoplastic rice starch (TPRS) showed higher stress at maximum load and Young’s modulus but lower strain at maximum load than the thermoplastic waxy rice starch (TPWRS). In addition, stress at maximum load and Young’s modulus of both TPRS and TPWRS increased significantly with the addition of the cotton fiber. Cotton fiber contents and lengths also affected mechanical properties of the TPRS and TPWRS composites. Moreover, water absorption of the TPRS and TPWRS composites decreased by the use of the cotton fibers. FT-IR and XRD techniques were used to study a change in functional group and crystallinity of the thermoplastic starch composites. Morphological, thermal and biodegradable properties of different thermoplastic starch composites were also investigated.     

Thermoplastic Blends from Albumin and Zein: Plastic Formation and Mechanical Properties Including Modeling

The use of proteins in blending with traditional polymers in the formation of thermoplastics can produce plastics with properties that are superior to traditional petroleum-based plastics. We investigated the physical and thermal properties of albumin and zein thermoplastic blends plasticized with glycerol and mixed with varying amounts of low-density polyethylene (LDPE). Several mechanical models were utilized to determine how tensile properties will be altered when varying amounts of protein/LDPE were added into the thermoplastic blend. When analyzed for thermal properties, we found that as the amount of LDPE in the thermoplastic blend increased, the resulting plastic possessed thermal properties that were more similar to pure LDPE plastics. In terms of mechanical properties, comparison between the experimental data and model predictions points to a synergistic effect between albumin and LDPE that leads to higher modulus, while a potential lack of compatibility between zein and LDPE leads to a plastic with lower modulus. Based on our results, the use of albumin and zein proteins when blended with LDPE in the production of thermoplastics has potential use in the areas of medical and food packaging applications.     

Antibacterial and Drug Elution Performance of Thermoplastic Blends

Food preservatives or drug compounds can be eluted from polymer substrates to prevent the occurrence of hospital-acquired infections and food spoilage. We investigated the antimicrobial and drug-elution properties of the albumin and zein thermoplastic blends plasticized with glycerol and mixed with varying amounts of low-density polyethylene (LDPE), food preservatives (sodium benzoate or sodium nitrite), and drugs (ampicillin or ciprofloxacin). Bacillus subtilis and Escherichia coli were utilized as Gram (+) and Gram (?) species, respectively, for antimicrobial and drug-elution analyses, since these species are common in the human body and in food environments. The amount of contamination occurring in food and medical applications could be limited with usage of plastic blends made from thermomechanical molding of proteins (albumin from hen egg white and zein from corn), drug eluting compounds, and low-density polyethylene.     

Melt Flow Behavior and Processability of Polylactic Acid/Polystyrene (PLA/PS) Polymer Blends

The present investigation dealt with the flow behavior and processability of polylactic acid/polystyrene (PLA/PS) polymer blends using a capillary rheometer. For this purpose, PLA/PS blends with different ratios of the concentrations were prepared using a single screw extruder. The shear viscosity, shear stress, shear rate, power-law index, viscous activation energy at a constant shear stress, and elongational stress were determined. PLA/PS blends exhibited a typical shear-thinning behavior over the entire range of shear rates tested, and the viscosity values of the blends would tend to decrease with increasing amount of PLA. In addition, the polymer blend of 70 % PLA and 30 % PS was found to be relatively less sensitive to the processing temperature, implying that the extrusion process was more desirable for fabrication of PLA/PS polymer blend than the injection process.     

Processing and Physical Properties of Plastics Made from Soy Protein Polyester Blends

Blending soy protein with polyesters using a polyvinyllactam as a compatibilizer successfully made soy protein-based plastics. The polyesters used to produce blends included polycaprolactone (PCL) and Biomax (a commercial biodegradable polyester). The blends were processed by compounding extrusion and injection molding. Blends containing soy protein/Biomax-poly(vinyl alcohol) had tensile strengths ranging from 16–22 MPa, with samples containing larger percentages of the synthetic polymer exhibiting greater strengths. Blends made from soy protein, Biomax, and PCL had tensile strengths ranging from 27–33 MPa. All the blends had high Young's moduli but demonstrated brittle characteristics as evident from their low elongations at break, ranging from 1.8–3.1%. Plastics made from soy protein/polyester blends exhibited low water absorption and had good stability under ambient conditions relative to the plastics made from soy protein alone. Blends made from soy protein flour produced plastics with the lowest water absorption.     

Biodegradable Corn Starch Loose-Fill. II. The Effect of Storage at Different Relative Humidities on the Physical Properties of Loose-Fill

The physical properties of corn starch loose-fill were examined at various relative humidities (r.h.). After 48 h of storage at both 25 and 50% r.h., only a slight change in the dimension and physical properties of the corn starch loose-fill was apparent. A wet environment (75% r.h. for 48 h), however, caused significant shrinkage and the loss of physical properties. The tensile properties, particularly tensile modulus, sharply increased, while the resilience gradually decreased with storage time. Amorphous X-ray diffraction patterns of corn starch loose-fills were transformed into crystalline patterns due to aging at 75% r.h. after 48 h. These changes were attributed to the structural relaxation, which was accelerated by moisture gain. The T _g of corn starch loose-fill decreased with increasing the moisture content in expanded starch. Our proposed model based on Avrami equation was able to describe the time-dependent recrystallization of corn starch by modifying the time-dependent tensile modulus. The growth parameter (n) and time constant (k) for the recrystallization process of corn starch loose-fill were about 3.2 and 8.87 × 10^–18 s^–1, respectively. If the growth parameter of 3.2 is considered, spherulitic growth of crystallization occurred in the corn starch loose-fill in the wet environment.