Environmental applications of single collector high resolution ICP-MS

The number of environmental applications of single collector high resolution ICP-MS (HR-ICP-MS) has increased rapidly in recent years. There are many factors that contribute to make HR-ICP-MS a very powerful tool in environmental analysis. They include the extremely low detection limits achievable, tremendously high sensitivity, the ability to separate ICP-MS signals of the analyte from spectral interferences, enabling the reliable determination of many trace elements, and the reasonable precision of isotope ratio measurements. These assets are improved even further using high efficiency sample introduction systems. Therefore, external factors such as the stability of laboratory blanks are frequently the limiting factor in HR-ICP-MS analysis rather than the detection power. This review aims to highlight the most recent applications of HR-ICP-MS in this sector, focusing on matrices and applications where the superior capabilities of the instrumental technique are most useful and often ultimately required.     

原子荧光法和电感耦合等离子体质谱法测定水中锑的比较

分别用原子荧光法(AFS)和电感耦合等离子体质谱法(ICP-MS)测定水中锑。AFS法和ICP-MS法均线性良好,相关系数分别为0.999 8和0.999 9,检出限分别为0.17和0.03μg/L,相对标准偏差均1.15%,加标回收率分别为96.6%~111.9%和95.4%~111.5%,2种方法均能很好地用于水中锑的测定。其中,ICP-MS法适合较清洁地表水和地下水样品中锑的分析,AFS法则对地表水、地下水和废水样品均适用。     

Critical appraisal of available thermodynamic data for the complexation of antimony(III) and antimony(V) by low molecular mass organic ligands

Antimony is an element of increasing environmental significance but one whose chemical speciation has received little attention and, until recently, one which had not been modelled in any comprehensive way. This paper reports thermodynamic data for computer speciation models of antimony in aqueous, multicomponent solutions of environmental and biological interest involving low molecular mass organic ligands. The available data have been critically evaluated and entered into a thermodynamic database. The JESS suite of computer programs has been used to develop the thermodynamically-consistent mass balance equations used for modelling purposes. No data could be found for Sb(V) complexes and only a few of the existing data for Sb(III) complexes can be considered as being reliably described.     

Electrochemical sensors for environmental monitoring: design, development and applications

The advancement in miniaturization and microfabrication technology has led to the development of sensitive and selective electrochemical devices for field-based and in situ environmental monitoring. Electrochemical sensing devices have a major impact upon the monitoring of priority pollutants by allowing the instrument to be taken to the sample (rather than the traditional way of bringing the sample to the laboratory). Such devices can perform automated chemical analyses in complex matrices and provide rapid, reliable and inexpensive measurements of a variety of inorganic and organic pollutants. Although not exhaustive due to the vast amounts of new and exciting electrochemical research, this review addresses many important advances in electrochemical sensor design and development for environmental monitoring purposes. Critical design factors and development issues including analytical improvements (e.g. detection limits), microfabrication and remote communication are presented. In addition, modern environmental applications will be discussed and future perspectives considered.     

固体废物氰化物总量和浸出毒性测定方法的比较

中国现行的固体废物氰化物总量和氰化物浸出毒性的分析方法存在缺陷,不便于广泛指导监测工作,笔者优化了固体废物氰化物测定的前处理方法,明确了固体废物氰化物总量、氰化物浸出毒性测定时的样品粒径、浸提方法和消解方法,建立了容量法、分光光度法、流动注射法测定固体废物氰化物总量和浸出毒性的方法,并与标准方法（离子色谱法）进行比较。实验结果表明：容量法、分光光度法、流动注射法测定结果与离子色谱法无显著差异,3种方法测定固体废物氰化物总量加标回收率为80.5%~102%,平行样测定相对标准偏差为3.0%~6.9%,3种方法测定固体废物氰化物浸出毒性加标回收率为80.1%~107%,平行样测定相对标准偏差为7.8%~9.5%,3种方法测定结果精密度和准确度良好,均能够满足固体废物氰化物总量和氰化物浸出毒性的测定要求。其中容量法、分光光度法由于其仪器设备简单、操作简便,可用于突发环境事件应急监测等情况下固体废物氰化物的测定。但容量法检出限较高,不能满足评价标准较低的分析测试工作要求,离子色谱法、分光光度法和流动注射法检出限均能满足一般分析测试要求。     

Monitoring of the natural environment by chemical speciation of elements in aerosol and sediment samples

The development of a monitoring network for chemical speciation of elements of aerosol and sediment samples collected at Lake Balaton has been carried out. Sequential leaching procedures for the determination of the distribution of elements in aerosols (3 steps) and sediments (4 steps) were used. These methods were recently successfully applied to describe environmentally mobile and stable fractions of toxic metals. In aerosol matrices the partition of elements was accomplished by particle size and chemical bonding. In sediments the distribution was performed by chemical bonding. The processes are called fractionation of elements. Particular attention was paid to distinguishing between environmentally mobile and environmentally immobile fractions because these represent the two extreme modes by which the metals are bound to solid matrices. The monitoring objectives were to assess pollution effects on man and his environment and to identify any possible cause and effect relationship between pollutant concentrations and health effects. The results of dry and wet deposition rates showed that most of the toxic metals were dissolved in an aqueous phase and the wet deposition played an important role. It has been found that, while the concentration of Cd and Pb in aerosols is low (0.7 and 29 ng m(-3), respectively), environmentally mobile fractions are considerable. Based upon the data it can be concluded that the effect of the anthropogenic sources on the quality of the lake is minor. This has been the first attempt to correlate speciation results between aerosols and sediments.     

Arsenic Speciation Analysis in Water Samples: A Review of The Hyphenated Techniques

Interests in the determination of different arsenic species in natural waters is caused by the fact that toxic effects of arsenic are connected with its chemical forms and oxidation states. In determinations of water samples inorganic arsenate (As(III), As(V)), methylated metabolities (MMAA, DMAA) and other organic forms such as AsB, AsC, arsenosugars or arsenic containing lipids have the most importance. This article provides information about occurrence of the dominant arsenic forms in various water environments. The main factors controlling arsenic speciation in water are described. The quantification of species is difficult because the concentrations of different forms in water samples are relatively lowcompared to the detection limits of the available analytical techniques. Several hyphenated methods used in arsenic speciation analysis are described. Specific advantages and disadvantages of methods can define their application for a particular sample analysis. Insufficient selectivity and sensitivity of arsenic speciation methods cause searching for a new or modifications already existing techniques. Some aspects of improvement and modifications of the methods are highlighted.     

Antimony speciation in terrestrial plants. Comparative studies on extraction methods

A suitable method for the extraction of antimony species from plant materials prior to IC-HG-AFS analysis is presented. The extraction efficiency with different extraction systems using various aqueous and aqueous/solvent mixtures was initially evaluated by analysing the Virginia Tobacco Leaves Certified Reference Material. The concentration of antimony extracted was compared with the total antimony content in the plant material measured by HG-AFS after focused microwave-acidic digestion using HNO3 and H2O2. The proposed extraction procedures were applied to antimony speciation in several plants from a natural terrestrial environment impacted by mining activities. End-over-end agitation (4 h) followed by sonication (1 h) extraction using 0.1 mol l(-1) citric acid was found to provide the best extraction efficiency while also giving reliable speciation information. Both inorganic and methylantimony species were found in the extractable portion of some terrestrial plants.     

Characterization of soil contamination by lead around a former battery factory by applying an analytical hybrid method

Former battery factories have created environmental and health problems for years and the exposure to lead in surface soils has been underestimated. Nonetheless, the identification of lead contamination and its spatial distribution is crucial. The determination of heavy metals in soils can be performed using inductively coupled plasma mass spectrometry (ICP-MS). However, alternative techniques such as X-ray fluorescence (XRF) have been used lately in environmental studies since measurements can be taken in the field in a prompt manner, despite its lower accuracy. In this study, a former battery factory site in Monterrey, Mexico, has been studied in order to detect lead contamination. Soil samples were assessed for contamination by using an analytical hybrid method that comprises both analytical techniques, namely, ICP-MS and XRF. Samples were taken in 215 locations and, after a simple homogenization process, they were analyzed by using a portable XRF device. Within those 215 sampling points, 25 samples were analyzed concurrently by using ICP-MS according to international sampling guidelines. Results obtained were adjusted in order to define an analytical hybrid method, which encompasses the advantages of each technique. An improved characterization was achieved by using the proposed analytical hybrid method since maps of lead distribution and calculated areas of concern showed better predictability. The combination of spectroscopic techniques is of great applicability for environmental agencies and decision makers.     

On-line solid phase extraction with polyurethane foam: trace level spectrophotometric determination of iron in natural waters and biological materials

This paper reports the development of a simple and accurate on-line procedure for preconcentration and determination of dissolved iron in waters and biological materials using unloaded polyether-type polyurethane foam as solid extractor. In the developed flow injection system, the analyte was preconcentrated from acidic aqueous medium as iron-thiocyanate complex with post-elution with ascorbic acid solution and spectrophotometric measurement with 1,10-phenanthroline as colorimetric reagent. In order to improve the performance of the system several chemical and flow variables were investigated as well as the effect caused by the presence of possible interferents. The method was validated by the analysis of two certified reference materials. Application of the methodology was carried out by the determination of dissolved iron content in eight natural water samples with different characteristics. The results were compared with those obtained by electrothermal atomic absorption spectrometry (ETAAS) and no statistical difference was observed. The detection limit was 0.75 microgram l-1 and the RSD was 1.2% for 2 min preconcentration time. At this condition, a productivity of 20 samples h-1 was achieved. Increasing the preconcentration time up to 3 min, a detection limit of 0.45 microgram l-1, an RSD of 1.5% and an analytical throughput of 15 h-1 were verified.     

Recommendations for Monitoring of Polybrominated Diphenyl Ethers in the Canadian Environment

Polybrominated diphenyl ethers (PBDEs) have been reported in air, surface waters, suspended sediments, soil, sediment, fish, marine mammals, and bird eggs throughout Canada, from the St. Lawrence Estuary to the Strait of Georgia and the northernmost reaches of the Canadian Arctic. Canadian scientists have detected the presence of PBDEs in breast milk in every Canadian province. In fact, recent data on temporal trends strongly suggests that the concentrations of PBDEs are on the rise in the Canadian environment. These findings are similar to those reported in other nordic countries, and have prompted several countries to implement environmental monitoring programs. Among the key challenges currently facing Canada and other countries concerns how best to measure these chemicals in different matrices. In this paper, several analytical methods cited in the scientific literature for determining PBDE concentrations in different abiotic and biological matrices are reviewed. The critical criteria required for accurate determination of PBDEs in complex environmental matrices are discussed, including instrument sensitivity, reliability, potential interference's and the need for specialized instrumentation for the determination of compounds up to 975 Daltons. While a single analytical method that meets these and other criteria has not yet been perfected by scientists, GC/HRMS-based methods amenable to isotope dilution techniques warrant further refinement, and likely represent the best tools for future environmental monitoring programs.     

The role of Raman spectroscopy in the analytical chemistry of potable water

Advances in instrumentation are making Raman spectroscopy the tool of choice for an increasing number of chemical applications. For example, many recalcitrant industrial process monitoring problems have been solved in recent years with in-line Raman spectrometers. Raman is attractive for these applications for many reasons, including remote non-invasive sampling, minimal sample preparation and tolerance of water. To a lesser extent, Raman spectroscopy is beginning to play a significant role in environmental analysis for the same reasons. At present, the environmental applications typically apply only to the most contaminated situations due to the still relatively high limits of detection. However, some emerging sampling technologies hold out the promise that Raman may soon be more widely applicable to the analytical chemistry of potable water. Herein we discuss these recent advances, summarize some examples of environmental applications to aqueous systems and suggest avenues of future developments that we expect to be most useful for potable water analysis. Also, a simplified, but detailed, theory of normal Raman scattering is presented. While resonance-enhanced Raman spectroscopy, surface-enhanced Raman spectroscopy and non-linear Raman techniques are briefly discussed, their theories and instrumental configurations are not addressed. Also, this article deals primarily with the modern dispersive Raman experiment (as opposed to the Fourier transform Raman experiment), because it seems most suited for potable water analysis. The goal of this article is to give the environmental scientist with no specialized knowledge of the topic just enough theory and background to evaluate the utility of this rapidly developing analytical tool.     

A new method for the determination of trichloroacetic acid in spruce foliage and other environmental media

Trichloroacetic acid (TCAA) is a phytotoxic chemical, present throughout the environment. The majority of methods for analysis of TCAA require chemical derivatisation and multiple extraction steps prior to analysis by gas-chromatography. Here, a new analytical method for TCAA determination in environmental matrices is reported. The method is based on a modified Nielsen-Kryger steam distillation that combines into one 1 h reflux the thermal decarboxylation of TCAA to CHCl3 and the partitioning and concentration of the CHCl3 into 5 ml of hexane, which is analysed by GC. Sample preparation is minimal and no matrix standard additions are required. The background CHCl3 in the sample is removed prior to extraction by degassing the solution for 1 h with nitrogen. Optimisation of the method gave recoveries from three separate solutions of 0.31 ppb aqueous TCAA standards of 93 +/- 15% (n = 9), 110 +/- 9% (n = 9) and 105 +/- 11% (n = 6). The extraction method has been compared with a decarboxylation and headspace GC method for determination of TCAA in Sitka spruce needles. No significant difference in TCAA concentration or replicate precision between the two methods was observed.     

Observations on the measurement of total antimony and antimony species in algae, plant and animal tissues

This paper describes our experiences with undertaking measurements of total antimony and antimony speciation in algae, plant and animal tissues. Digestion with nitric acid alone is suitable to release antimony from animal tissues. When organisms have high silica contents, e.g. some plants and algae, the addition of tetrafluorboric acid is required to dissolve silica as some antimony is retained by silica in extracts. Antimony in digested extracts is present as Sb5+ and hydride generation procedures can be used to determine total antimony concentrations, as total antimony in extracts will not be under estimated. Relatively non-aggressive solvents such as water, dilute nitric acid, sodium hydroxide and enzymes remove highly variable amounts of antimony (2-84%) from algae, plant and animal tissues. Addition of Sb3+ and Sb5+ to NIST CRM 1572 Citrus Leaves, pre- and post-extraction with water showed that Sb3+ is oxidised to Sb5+ while Sb5+ is redistributed amongst binding sites giving rise to artefacts. DOLT-2 and algae extracts indicated the presence of only inorganic antimony. A moss sample had inorganic antimony and a number of unknown antimony species in extracts. Future studies should explore the nature of the binding of antimony in tissues as solvents commonly used to extract metals and metalloids from algae, plant and animal tissues are not appropriate.     

Speciation of metals in bed sediments and water of Qaraaoun Reservoir, Lebanon

Determination of only total element in sediments does not give an accurate estimate of the likely environmental impacts. Speciation study of metals in sediment provides information on the potential availability of metals (toxic) to biota under various environmental conditions. In water, the toxic metal specie is the free hydrated metal ion. The toxicity of metals depends especially on their chemical forms rather than their total metal content. The present study focuses on Qaraaoun Reservoir, Lebanon. Earlier studies focused only on total metal concentrations in sediment and water. The objective of this study was to determine metal speciation (Fe, Cr, Ni, Zn, Cu, Pb, Cd) in the (operationally defined) sediment chemical fractions and metal speciation in reservoir water. This would reflect on metal bioavailability and toxicity. Water samples and bed sediments were collected from nine sites during the dry season and a sequential chemical fraction scheme was applied to the <75-??m sieve sediment fraction. Metal content in each fraction was determined by the FAAS technique. The data showed that the highest percentages of total metal content in sediment fractions were for: Fe in residual followed by reducible, Cr and Ni in residual and in reducible, Cu in organic followed by exchangeable, Zn in residual and in organic, Pb in organic and carbonate, Cd was mainly in carbonate. Total metal content in water was determined by ICP-MS technique and aqueous metal speciation was predicted using AQUACHEM software interfaced to PHREEQC geochemical computer model. The water speciation data predicted that a high percentage of Pb and Ni were present as carbonate complex species and low percentages as free hydrated ions, highest percentage of Zn as carbonate complex species followed by free hydrated ion, highest percentage of Cd as free hydrated ion followed by carbonate complex species. The sensitivity attempt of free hydrated ion of Ni, Zn, Pb, and Cd in reservoir water revealed dependence of Zn and Cd on pH and alkalinity, while Ni and Pb were only dependent on pH.     

Microtrace Metalloids Speciation in Lakes Water Samples (Poland)

This paper presents the results of the determination of arsenic, antimony and selenium concentrations of inorganic speciation in surface water samples from Gniezno city (western Poland) and its neighborhood. The concentration of elements were up to 1.85 ng/ml for arsenic, 1.61 ng/ml for antimony and 0.45 ng/ml for selenium (detection limits: 0.04 ng/ml for As and Sb and 0.03 ng/ml for Se). A variety of concentrations for the determined elements has been obtained in waters from Gniezno city’s neighborhood and in water from down-town reservoirs which are under strong anthropogenic pressure.     

Influence of reagent purity on the ion chromatographic determination of bromate in water using 3,3'-dimethoxybenzidine as a prochromophore for photometric detection

Variable availability of the purified dihydrochloride salt of 3,3'-dimethoxybenzidine (DMB; ortho-dianisidine) led us to investigate the effects of reagent purity on the analytical results obtained when this reagent is used in the photometric determination of the disinfection byproduct bromate. After analyte ions are separated by ion chromatography, a solution of DMB (post-column reagent) is added to the eluate and the DMB is oxidized, thereby producing a chromophore detected by its absorbance. Although some commercial products of undefined grade performed well, others did not. Variability was also observed between lots of purified material. Sensitivity at low concentrations (< 5 micrograms L-1 BrO3-) varied by a factor of up to 10. In some cases, the lower limit of detection for photometric detection was greater than that obtained using conductivity detection, as high as 5-7 micrograms L-1 BrO3-. An impurity or several impurities are suspected to be responsible for deviations from linearity at low analyte concentrations. This investigation underscores the need for ensuring reagent purity in environmental analyses. Ideally, chemical manufacturers will meet the needs of analytical chemists who test potable water and begin producing a high grade material in sufficient quantities to meet monitoring requirements. The establishment of third-party standards for a spectrophotometric grade of DMB.2HCl would be helpful in ensuring that a variety of manufacturers could supply products of uniformly high quality that would be suitable for the measurement of bromate in public drinking water supplies.     

Determination of antimony in human blood with inductively coupled plasma-mass spectrometry

A method is presented for the determination of antimony in whole human blood samples with an ICP-MS instrument using a quadrupole mass analyzer. A nitric acid/hydrogen peroxide open digestion procedure was employed for the blood sample treatment and preparation for analysis. The precision and accuracy of the method were evaluated by analyzing several Seronorm trace elements whole blood reference materials. The precision of the method at various antimony levels was better than 4% RSD and the recovery was greater than 92% at all levels. The detection limit, calculated as three times the standard deviation of the blank (3sigma, n= 12), was 0.03 microg L(-1). The method was successfully applied for the determination of antimony in blood samples from school children in rural areas of Kwazulu/Natal, South Africa and adults from Dearborn, Michigan. Blood antimony levels ranged from <0.03 to 3.82 microg L(-1) in children and 1.40 to 4.35 microg L(-1) for adults.     

Laser-induced breakdown spectroscopy application in environmental monitoring of water quality: a review

Water quality monitoring is a critical part of environmental management and protection, and to be able to qualitatively and quantitatively determine contamination and impurity levels in water is especially important. Compared to the currently available water quality monitoring methods and techniques, laser-induced breakdown spectroscopy (LIBS) has several advantages, including no need for sample pre-preparation, fast and easy operation, and chemical free during the process. Therefore, it is of great importance to understand the fundamentals of aqueous LIBS analysis and effectively apply this technique to environmental monitoring. This article reviews the research conducted on LIBS analysis for liquid samples, and the article content includes LIBS theory, history and applications, quantitative analysis of metallic species in liquids, LIBS signal enhancement methods and data processing, characteristics of plasma generated by laser in water, and the factors affecting accuracy of analysis results. Although there have been many research works focusing on aqueous LIBS analysis, detection limit and stability of this technique still need to be improved to satisfy the requirements of environmental monitoring standard. In addition, determination of nonmetallic species in liquid by LIBS is equally important and needs immediate attention from the community. This comprehensive review will assist the readers to better understand the aqueous LIBS technique and help to identify current research needs for environmental monitoring of water quality.     

Sequential extractions of selenium soils from Stewart Lake: total selenium and speciation measurements with ICP-MS detection

Different techniques have been employed in order to evaluate the most efficient procedure for the extraction of selenium from soil as required for speciation. Selenium contaminated sediments from Stewart Lake Wetland, California were used. A strong acid mineralization of the samples gives quantitative total selenium, which is then used to estimate recoveries for the milder extraction methods. The different extraction methodologies involve the sequential use of water, buffer (phosphate, pH 7) and either acid solution (e.g. HNO3 or HCl) or basic solutions (e.g. ammonium acetate, NaOH or TMAH). Pyrophosphate extraction was also evaluated and showed that selenium was not associated with humic acids. The extractants were subsequently analyzed by size exclusion chromatography (SEC) with UV (254 and 400 nm) and on-line ICP-MS detection; anion exchange chromatography, and ion-pair reversed phase chromatography with ICP-MS detection. For sequential extractions the extraction efficiencies showed that the basic extractions were more efficient than the acidic. The difference between the acidic and the basic extraction efficiency is carried to the sulfite extraction, suggesting that whatever is not extracted by the acid is subsequently extracted by the sulfite. The species identified with the different chromatographies were selenate, selenite, elemental selenium and some organic selenium.