可见光活化过硫酸盐降解双(2-氯乙基)醚

研究了不同活化方式下过硫酸盐对双(2-氯乙基)醚(BCEE)的降解效果,重点考察了可见光活化过硫酸盐降解BCEE体系中过硫酸钠投加量、BCEE初始浓度、初始pH以及无机阴离子和腐殖酸对反应的影响。结果表明,酸性条件下BCEE的降解效果较好,且随着过硫酸钠投加量增大或BCEE初始浓度减小,BCEE的降解率提高。反应最佳条件为BCEE质量浓度4mg/L、过硫酸钠投加量20mmol/L、溶液初始pH调至3,降解过程符合一级动力学方程。溶液中存在CO23-、HCO3-或Cl-均对BCEE的降解有抑制作用,加入腐殖质则会促进BCEE的降解。通过液-液萃取进行前处理,使用气相色谱/质谱分析检测出3种降解中间产物,分别为1,2-二氯丙烷、氯甲酸异丙酯和氯甲酸氯乙酯。     

Effect of ultrasonication and Fenton oxidation on biodegradation of bis(2-ethylhexyl) phthalate (DEHP) in wastewater sludge

The presence of bis(2-ethylhexyl) phthalate (DEHP) and its metabolites, i.e. 2-ethylhexanol, 2-ethylhexanal, and 2-ethylhexanoic acid in wastewater sludge (WWS) were investigated during aerobic digestion and Bacillus thuringiensis (Bt)-based fermentation of WWS. Ultrasonication and Fenton oxidation pre-treatment was applied to improve biodegradability of WWS and bioavailability of the target compounds for digestion and fermentation. DEHP and 2-ethylhexanoic acid were observed at higher concentration, meanwhile 2-ethylhexanol and 2-ethylhexanal were observed at lower concentration in WWS. After 20-day aerobic digestion, DEHP removal was 72%, 89%, and 85%, and 2-ethylhexanoic acid removal was 71%, 84%, 79%, respectively for raw, ultrasonicated, and Fenton-oxidized sludges. Bt was found to degrade DEHP, leading to DEHP removal of 21%, 40%, and 30%, respectively for raw, ultrasonicated, and Fenton-oxidized sludges in the fermentation. The results suggested that aerobic stabilization and Bt-based fermentation can remove the phthalates, and pre-treatment of WWS was also effective in improvement of DEHP biodegradation. Hence, Bt-based biopesticide production from WWS can be applied safely when taking into consideration the phthalate contaminants.     

MIL-88B(Fe)非均相芬顿催化降解磺胺甲恶唑

采用溶剂热法合成了铁基金属有机骨架材料MIL-88B(Fe),将其作为类芬顿催化剂用于催化降解水中磺胺甲恶唑(SMX)。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、傅立叶变换红外光谱(FTIR)和X射线光电子能谱(XPS)等对催化剂的结构和性能进行表征,并研究了H₂O₂浓度、催化剂投加量、溶液初始pH和污染物初始浓度等对SMX降解效果的影响。结果表明,在H₂O₂摩尔浓度为6.0mmol/L、催化剂投加量为0.2g/L、pH为4、SMX为5mg/L的优化反应条件下,MIL-88B(Fe)对SMX的降解率可达99%。在较宽的pH(4～6)范围内,MIL-88B(Fe)仍保持较好的催化活性,且5次循环使用后对SMX去除率仍可达95%以上。表明合成的MIL-88B(Fe)具有较高的催化活性和重复性能,是一种优良的非均相类芬顿催化剂。     

Heterogeneous Fenton degradation of ofloxacin catalyzed by magnetic nanostructured MnFe2O4 with different morphologies

Environmental Science and Pollution Research - Magnetic nanostructured MnFe2O4 with different morphologies, synthesized via chemical co-precipitation and hydrothermal method, was assayed as...     

Surface properties and catalytic performance of La(1-x)Sr(x)FeO(3) perovskite-type oxides for methane combustion

La(1-x)Sr(x)FeO(3) (x=0.0-1.0) perovskites were prepared and tested for the combustion of methane. X-ray diffraction (XRD) patterns revealed the presence of a single perovskite structure for substitutions 0x0.3, however Fe(2)O(3), SrCO(3) and SrFeO(3) phases were observed for substitutions x>0.3. The results of activity test indicate that with La(1-x)Sr(x)FeO(3) as the catalyst, the combustion of methane can take place at low temperatures around 400 degrees C. Partial substitution of La with Sr increases the activity and an optimal substitution fraction (x=0.5) exists in the La(1-x)Sr(x)FeO(3) catalysts. Catalyst activity can be well correlated to the product of the specific surface area and atomic ratio of Fe to La+Sr on the catalyst surface. Experimental results of O(2)-TPD and CH(4)-TPD in the range of 350-500 degrees C indicate that the amount of oxygen desorbed from the La(1-x)Sr(x)FeO(3) catalysts is far larger than that of methane. Therefore, it can be proposed that the catalytic oxidation of CH(4) over these catalysts proceeds with the surface reaction between CH(4) in the gas phase and the adsorbed O(2). Addition of water vapor or CO(2) to the feed inhibited catalyst activity, but the inhibition was reversible and became negligible at high reaction temperature.     

Gas-phase reaction of CCl2F2 (CFC-12) with methane

Gas-phase reaction of CFC-12 (CCl2F2) with methane was carried out in a plug flow reactor over the temperature range of 873-1123 K. The major organic halocarbons formed during the reaction were C2F4, C2H2F2, CHClF2, CH3Cl, C3H2F6 and CCl3F. The formation of all products except C2H2F2 decreased with temperature, while the selectivity to C2H2F2 (difluoroethylene) increased with temperature and reached approximately 80% at 1123 K. Under these reaction conditions, methane acts as hydrogen and carbon source, resulting in the formation of an unsaturated C2 hydrofluorocarbon from two C1 precursors.     

Degradation of rhodamine B by Fe(0)-based Fenton process with H2O2

Degradation of rhodamine B by Fe(0)-based Fenton process with H₂O₂ was investigated. The effects of H₂O₂ dose, Fe(0) dose, initial concentration of rhodamine B and initial pH value on the degradation of rhodamine B were examined. The results showed that the degradation and mineralization of rhodamine B occurred with low dose of H₂O₂ and Fe(0). The intermediates of rhodamine B were analyzed with UV-Vis spectrophotometry and ion chromatography and the mechanism of oxidative degradation of rhodamine B was also discussed. The reactive oxygen species (·OH) produced in Fe(0)-based Fenton process with H₂O₂ is the key to the degradation of rhodamine B by ways of N-de-ethylation, chromophore cleavage, ring-opening and mineralization.     

Heterogeneous UV/Fenton degradation of bisphenol A catalyzed by synergistic effects of FeCo2O4/TiO2/GO

A new method for bisphenol A (BPA) degradation in aqueous solution was developed. The characteristics of BPA degradation in a heterogeneous ultraviolet (UV)/Fenton reaction catalyzed by FeCo₂O₄/TiO₂/graphite oxide (GO) were studied. The properties of the synthesized catalysts were characterized using scanning electron microscopy, X-ray diffraction, and vibrating sample magnetometry. FeCo₂O₄ and TiO₂ were grown as spherical shape, rough surface, and relatively uniform on the surface of GO (FeCo₂O₄/TiO₂/GO). Batch tests were conducted to evaluate the effects of the initial pH, FeCo₂O₄/TiO₂/GO dosage, and H₂O₂ concentration on BPA degradation. In a system with 0.5 g L⁻¹ of FeCo₂O₄/TiO₂/GO and 10 mmol L⁻¹ of H₂O₂, approximately 90 % of BPA (20 mg L⁻¹) was degraded within 240 min of UV irradiation at pH 6.0. The reused FeCo₂O₄/TiO₂/GO catalyst retained its activity after three cycles, which indicates that it is stable and reusable. The heterogeneous UV/Fenton reaction catalyzed by FeCo₂O₄/TiO₂/GO is a promising advanced oxidation technology for treating wastewater that contains BPA.

     

Applicability of Fenton and H2O2/UV reactions in the treatment of tannery wastewaters

In this paper we evaluated the H2O2/UV and the Fenton's oxidation processes for the treatment of tannery wastewater under different experimental conditions. Efficiencies were judged by the amounts of organic substances degraded or eliminated under these treatment techniques. Daphnia magna and Vibrio fischeri were used to monitor toxicity. Organic compounds contained in the untreated and treated tannery wastewater were determined and identified using substance specific techniques. Gas chromatography-mass spectrometry (GC-MS) in positive electron impact (EI(+)) mode was applied to determine volatile organics. Atmospheric pressure ionization (API) mass (MS) and tandem mass spectrometry (MS-MS) coupled with flow injection analysis (FIA) or liquid chromatography (LC) were used to detect or identify polar organic pollutants. The experimental results indicated that both oxidation processes--H2O2/UV at pH 3 and Fenton at pH 3.5--are able to reduce TOC content by mineralisation of the organic compounds.     

Microbial degradation of bis(tributyltin) oxide

The degradation of the biocide bis (tributyltin) oxide by pur cultures of microorganisms has been studied. Attempts to isolate microorganisms able to utilize bis (tributyltin) oxide as sole carbon source, were unsuccessful. Of many bacterial species investigated $\text{Pseudomonas aeruginosa}$ and $\text{Alcaligenes faecalis}$ degraded sublethal amounts of bis (tributyltin) oxide during aerobic growth in the presence of suitable carbon sources. $\text{P. aeruginosa}$ converted bis (tributyltin) oxide into monobutyltin and small amounts of dibutyltin derivatives. Similar results were obtained with growing mycelium of $\text{Coniophora puteana}$, $\text{Trametes versicolor}$ and $\text{Chaetomium globosum}$. Microbial conversion of monobutyltin trichloride was not observed. Dibutyltin dichloride was converted into monobutyltin derivatives under certain sterile conditions.     

NaNO(2)/FeCl(3) catalyzed wet oxidation of the azo dye Acid Orange 7

A combination of ferric chloride and sodium nitrite significantly improved the wet oxidation of the azo dye Acid Orange 7 (AO7) in acid aqueous media (pH 2.6) under moderate conditions (T=150 degrees C; oxygen pressure=0.5 MPa). To evaluate the catalytic system, wet oxidation of AO7 was carried out at temperatures between 90 and 150 degrees C and oxygen pressures ranging from 0.1 to 0.5 MPa. The effect of initial solution pH from 2.6 to 11.4 and the amount of catalyst on the degradation of AO7 were also investigated. AO7 initial concentration was kept 200 mg L(-1). The degradation process was monitored by UV-visible spectroscopy, HPLC, IC (ion chromatography), GC-MS and TOC analysis. At 150 degrees C and 0.5 MPa oxygen pressure, 56% TOC was removed after 4h of treatment, while no obvious TOC removal were achieved without catalyst at the same experimental condition. The main degradation products were some small organic acids: formic acid, acetic acid, pyruvic acid, oxalic acid, succinic acid (identified and quantified by IC) and phthalic acid (identified by GC-MS).     

Electrochemical treatment of semi-aerobic landfill leachate using Response Surface Methodology (RSM)

This research investigated the effectiveness of electrochemical treatment in treating semi-aerobic landfill leachate. The electrolytic reactor assembly included a pair of aluminium electrodes, a power supply and NaCl as electrolyte. The interactive effects of initial COD, current density and reaction time on treated leachate quality were studied. Regression equations were developed using design-expert software and results were analysed using response surface methodology. At optimum conditions (2000 mg/L initial COD, about 17 mA/cm² current density, 4 h reaction time and 1 g/l NaCl), SCOD removal, BOD removal and colour removal were estimated to be 82.2, 81.5 and 95%, respectively.     

Photocatalytic debromination of preloaded decabromodiphenyl ether on the TiO(2) surface in aqueous system

There have been serious concerns about polybromodiphenyl ethers (PBDEs) in the environment because of their global distribution and bioaccumulation. Owing to strong hydrophobicity of PBDEs, the regular photocatalytic system, in which the substrate is solvated in the bulk solution, is not applicable to the removal of the PBDEs in water. In this work, the photocatalytic reduction degradation of decabromodiphenyl ether (BDE209), the most-used PBDEs, was investigated in aqueous system, by pre-adsorbing it on the surface of photocatalyst. It was found that the preloaded BDE209 underwent efficient reductive debromination in aqueous system under irradiation with wavelength larger than 360 nm in the presence of electron donors such as methanol. Our experiments further show that such a preloaded system exhibits different characteristics from that in the organic solution. The meta-debrominated intermediate is predominant in the present system, while the ortho-debrominated one is the main nona-BDE products in the organic solution. In addition, different from other photocatalytic system, the pH has little effect on the photocatalytic reaction. We propose that these differences are originated from the formation of overlayer of hydrophobic BDE209 to limit the motion of BDE209 and the access of water and H⁺/OH⁻ to the TiO₂ surface.     

Fate of citalopram during water treatment with O3, ClO2, UV and Fenton oxidation

In the present study we investigate the fate of citalopram (CIT) at neutral pH using advanced water treatment technologies that include O₃, ClO₂ oxidation, UV irradiation and Fenton oxidation. The ozonation resulted in 80% reduction after 30 min treatment. Oxidation with ClO₂ removed >90% CIT at a dosage of 0.1 mg L⁻¹. During UV irradiation 85% reduction was achieved after 5 min, while Fenton with addition of 14 mg L⁻¹ (Fe²⁺) resulted in 90% reduction of CIT. During these treatment experiments transformation products (TPs) were formed from CIT, where five compounds were identified by using high resolution and tandem mass spectrometry. Among these desmethyl-citalopram and citalopram N-oxide have been previously identified as human metabolites, while three are novel and published here for the first time. The three TPs are a hydroxylated dimethylamino-side chain derivative, a butyrolactone derivative and a defluorinated derivative of CIT.     

Oxidative transformation of polybrominated diphenyl ether congeners (PBDEs) and of hydroxylated PBDEs (OH-PBDEs)

BACKGROUND, AIM, AND SCOPE: The historical and widespread use of polybrominated diphenyl ethers (PBDEs) as flame retardants in consumer products worldwide has caused PBDEs to now be regarded as pervasive environmental contaminants. Most recently, hydroxylated PBDEs (OH-PBDEs) and methoxylated PBDEs (MeO-PBDEs) have emerged as environmentally relevant due to reports of their natural production and metabolism. An important parameter for assessing the environmental impact of a chemical substance is persistence. By formulating the concept that persistence is the result of the substance's physicochemical properties and chemical reactivity, Green and Bergman have proposed a new methodology to determine the inherent persistence of a chemical. If persistence could be predicted by straightforward methods, substances with this quality could be screened out before large-scale production/manufacturing begins. To provide data to implement this concept, we have developed new methodologies to study chemical transformations through photolysis; hydrolysis, substitution, and elimination; and via oxidation. This study has focused on adapting an oxidative reaction method to be applicable to non-water soluble organic pollutants. MATERIALS AND METHODS: PBDEs and one MeO-PBDE were dissolved in tetrahydrofuran/methanol and then diluted in alkaline water. The OH-PBDEs were dissolved in alkaline water prior to reaction. The oxidation degradation reaction was performed at 50 degrees C using potassium permanganate as described elsewhere. The pH was maintained at 7.6 with disodium hydrogen phosphate and barium hydrogen phosphate, the latter also serving as a trapping agent for manganate ions. The oxidation reactions were monitored by high-performance liquid chromatography and reaction rates were calculated. RESULTS: The OH-PBDEs have very fast oxidative transformation rates compared to the PBDEs. The reaction rates seem to be primarily dependent on substitution pattern of the pi-electron-donating bromine substituents and of bromine content. There are indications that further reactions of OH-PBDEs, e.g., methylation to the MeO-PBDEs, decrease the oxidation rates, and thereby generate more persistent substances. DISCUSSION: The resistance of PBDEs to oxidation, a major degradation pathway in air, should be further investigated, since these compounds do undergo long range transport. With slight modifications, the original method has been adapted to include a larger variety of chemical substances, and preliminary data are now available on the oxidative transformation rates for PBDEs and of OH-PBDEs. CONCLUSIONS: The original oxidation degradation method can now include non-water soluble compounds. This modification, using low concentrations of test chemicals, allows us to measure oxidative transformation rates, for some of the lower brominated DEs, data that can be used to assess their persistence in future model calculations. Oxidative transformation rates for PBDEs are slow compared to those for the OH-PBDEs. This suggests that OH-PBDEs, when released into the environment, undergo faster oxidative metabolism and excretion than the PBDEs. RECOMMENDATIONS AND PERSPECTIVES: To evaluate the modified method, more degradation reactions with non-water soluble compounds should be investigated. Recent studies show that OH-PBDEs are present in rats and in humans and, because of their activity as endocrine disruptors, determining their subsequent environmental fate is of importance. The resistance of PBDEs to oxidative degradation should be acknowledged as of possible future concern. Several other compound classes (such as polychlorinated biphenyls (PCBs), hydroxylated polychlorinated biphenyls (OH-PCBs), and pharmaceuticals) need to be subjected to this screening method to increase the database of transformation rates that can be used with this model.     

混凝与Fenton联用处理垃圾渗滤液的效能及成本

为对混凝/Fenton工艺与Fenton/混凝工艺处理垃圾渗滤液的效果和成本进行比较,分别对年轻渗滤液和老龄渗滤液原液按照混凝/Fenton工艺与Fenton/混凝工艺2种技术路线进行处理。实验结果表明,Fenton试剂对年轻垃圾渗滤液和老龄垃圾渗滤液COD去除率最高的反应条件为pH=3.5、H2O2和Fe2+的摩尔比为6、H2O2和渗滤液原液的COD质量比为3、反应时间4 h;在PAC与渗滤液原液的COD质量比为0.6时,PAC混凝对渗滤液原液的COD去除率最高。在对渗滤液COD去除率最高的Fenton反应和PAC混凝反应条件下,混凝/Fenton工艺对年轻渗滤液和老龄渗滤液的COD去除率分别为90.56%和86.56%;Fenton/混凝工艺对年轻渗滤液和老龄渗滤液的COD去除率分别为89.99%和85.99%,2种技术路线对渗滤液COD的去除率相差不大,但先PAC混凝后Fenton氧化工艺比先Fenton后混凝工艺每t节省62.6元,是更优化的渗滤液处理工艺。     

Biotic and abiotic transformations of methyl tertiary butyl ether (MTBE)

Background Methyl tertiary butyl ether (MTBE) is a fuel additive which is used all over the world. In recent years it has often been found in groundwater, mainly in the USA, but also in Europe. Although MTBE seems to be a minor toxic, it affects the taste and odour of water at concentrations of < 30 μg/L. Although MTBE is often a recalcitrant compound, it is known that many ethers can be degraded by abiotic means. The aim of this study was to examine biotic and abiotic transformations of MTBE with respect to the particular conditions of a contaminated site (former refinery) in Leuna, Germany. Methods Groundwater samples from wells of a contaminated site were used for aerobic and anaerobic degradation experiments. The abiotic degradation experiment (hydrolysis) was conducted employing an ion-exchange resin and MTBE solutions in distilled water. MTBE, tertiary butyl formate (TBF) and tertiary butyl alcohol (TBA) were measured by a gas chromatograph with flame ionisation detector (FID). Aldehydes and organic acids were respectively analysed by a gas chromatograph with electron capture detector (ECD) and high-performance ion chromatography (HPIC). Results and Discussion Under aerobic conditions, MTBE was degraded in laboratory experiments. Only 4 of a total of 30 anaerobic experiments exhibited degradation, and the process was very slow. In no cases were metabolites detected, but a few degradation products (TBF, TBA and formic acid) were found on the site, possibly due to the lower temperatures in groundwater. The abiotic degradation of MTBE with an ion-exchange resin as a catalyst at pH 3.5 was much faster than hydrolysis in diluted hydrochloric acid (pH 1.0). Conclusion Although the aerobic degradation of MTBE in the environment seems to be possible, the specific conditions responsible are widely unknown. Successful aerobic degradation only seems to take place if there is a lack of other utilisable compounds. However, MTBE is often accompanied by other fuel compounds on contaminated sites and anaerobic conditions prevail. MTBE is often recalcitrant under anaerobic conditions, at least in the presence of other carbon sources. The abiotic hydrolysis of MTBE seems to be of secondary importance (on site), but it might be possible to enhance it with catalysts. Recommendation and Outlook MTBE only seems to be recalcitrant under particular conditions. In some cases, the degradation of MTBE on contaminated sites could be supported by oxygen. Enhanced hydrolysis could also be an alternative. - * The basis of this peer-reviewed paper is a presentation at the 9th FECS Conference on 'Chemistry and Environment', 29 August to 1 September 2004, Bordeaux, France.     

Factors affecting degradation of dimethyl sulfoxide (DMSO) by fluidized-bed Fenton process

In this study, the target compound is dimethyl sulfoxide (DMSO), which is used as a photoresist stripping solvent in the semiconductor and thin-film transistor liquid crystal display (TFT-LCD) manufacturing processes. The effects of the operating parameters (pH, Fe²⁺ and H₂O₂ concentrations) on the degradation of DMSO in the fluidized-bed Fenton process were examined. This study used the Box-Behnken design (BBD) to investigate the optimum conditions of DMSO degradation. The highest DMSO removal was 98 % for pH 3, when the H₂O₂ to Fe²⁺ molar ratio was 12. At pH 2 and 4, the highest DMSO removal was 82 %, when the H₂O₂ to Fe²⁺ molar ratio was 6.5. The correlation of DMSO removal showed that the effect of the parameters on DMSO removal followed the order Fe²⁺?>?H₂O₂?>?pH. From the BBD prediction, the optimum conditions were pH 3, 5 mM of Fe²⁺, and 60 mM of H₂O₂. The difference between the experimental value (98 %) and the predicted value (96 %) was not significant. The removal efficiencies of DMSO, chemical oxygen demand (COD), total organic carbon (TOC), and iron in the fluidized-bed Fenton process were higher than those in the traditional Fenton process.     

Fenton (H2O2/Fe) reaction involved in Penicillium sp. culture for DDT [1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane)] degradation

The purpose of this work was to demonstrate that a Fenton (H₂O₂/Fe) reaction was involved in DDT [1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane)] degradation in a culture of Penicillium sp. spiked with FeSO₄. A commercial DDT mixture (10% DDE [1,1-dichloro-2,2-bis(p-chlorophenyl)ethylene], 30% o,p-DDT and 60% of p,p′ -DDT) of 10 mg L^{? 1} was used. Hydrogen peroxide (H₂O₂), tartaric acid and oxalic acid were identified at 18 h in culture media, with and without added DDT; this correlated positively with lowering of pH from 5.8 to 2.7. Lower concentrations of oxalic acid and H₂O₂ (7.9 and 52.6 mg L^{? 1}, respectively) occurred in media with DDT at 30 h, in comparison to that one without DDT mixture (27.9 and 65.3 mg L^{? 1}, respectively), at this time there was maximum degradation (87.7, 91.7 and 94.2%) for DDE, o,p-DDT and p,p′-DDT, respectively. We propose that the degradation of the DDT mixture by Penicillium sp. was through a Fenton reaction (H₂O₂/Fe) under acidic conditions produced in situ during the fungal culture amended with FeSO₄.