脉冲电晕法藕合Ca(OH)2固体吸收处理四氯乙烯废气研究

采用线-筒式脉冲电晕反应器对四氯乙烯去除效果进行了研究.结果表明,四氯乙烯去除率随电压的增大而增大.在氮气中加入氧气,四氯乙烯降解效果低于纯氮气下的降解效果.四氯乙烯在氮气下的主要气相产物为Cl_2和少量的CCl_4.当氧气加入后,四氯乙烯主要降解为CO_2、CO、COCl_2、O_3和C_2Cl_4O.为了去除有害中间产物,在反应器中加入Ca(OH)_2固体吸收剂,这明显提高了有害中间产物的去除,存在水汽及含Ca(OH)_2固体吸收剂时并未检测到COCl_2、O_3和有害中间产物C_2Cl_4O,但水汽不利于四氯乙烯去除.     

非热等离子体结合CuO催化剂或Ca(OH)2吸收剂去除氮氧化物

采用非热等离子体结合催化或现场化学吸收的2种方法来去除气流中的NOx.结果表明,非热等离子体结合催化,反应器内的CuO催化剂能有效地促进NO的还原反应;相对于催化还原NO而言,脉冲电晕作用下能有效地降低NO催化还原的反应温度.当催化剂为CuO,脉冲电压为18kV,反应温度为200℃,还原剂为1%CO及NO进口浓度为719 mg/m3条件下,NO的去除率达到了100%.非热等离子体结合现场化学吸收方法,是一种在常温下从气流中净化氮氧化物的有效方法,NO的去除率远远高于反应器内没有吸收剂的情况.可以认为反应器内的Ca(OH)2吸收剂通过与NO的氧化产物NO2或NO3的吸收反应促进了NO的去除.当反应器内有Ca(OH)2吸收剂存在时,在脉冲电压为18kV,O2浓度为2%及NO进口浓度为1 050 mg/m3条件下,NO的去除率达到了100%.     

活性炭催化过氧化氢去除荧光增白剂

研究了活性炭(activated carbon,AC)吸附、改性活性炭(activated carbon modified,ACM)吸附、过氧化氢(H2O2)氧化、AC催化H2O2等方法对水体中荧光增白剂VBL的处理效果,并通过自由基俘获剂叔丁醇、催化过程气体分析等探讨了AC催化H2O2分解VBL的机制.结果表明,经硝酸铁[Fe(NO3)3]改性过的ACM对VBL的吸附去除率高于未改性的AC.活性炭催化H2O2对VBL的去除效果明显,但未改性AC催化去除率高于ACM.60 min时,AC催化氧化去除率即可达到95%以上,而ACM仅为58%.叔丁醇的加入降低了AC和ACM催化氧化对VBL的去除率,表明AC催化H2O2氧化能促进H2O2形成羟基自由基(·OH)和原子氧参与反应.AC催化H2O2分解及释放气体分析表明,AC能催化H2O2形成氧气并放热,且ACM明显快于AC.结合催化H2O2去除VBL效率的结果分析,ACM催化反应时活性中间物(自由基和原子氧等)产生速率快于AC,活性中间物自身消耗形成氧气,而不是用于分解VBL.催化反应中活性中间产物的形成速率与反应物供给速率的不匹配可能是导致ACM催化效果弱于AC的重要原因.     

介质阻挡放电脱除H2S影响因素研究

恶臭污染物的危害已引起世界各国的广泛关注.选取恶臭污染物的典型代表硫化氢(H2S)气体,采用介质阻挡放电低温等离子体反应器在常温常压下对H2S气体进行去除,考察了在高频放电条件下,H2S去除率与放电电压、频率、浓度、停留时阃、湿度、和放电间隙、占空比的关系.实验结果表明,较高的放电电压、较长的停留时间、较大的放电间隙有利于提高H2S去除,合适的湿度、放电频率、脉冲调制有利于提高反应器的效率.反应器参数与电源的有效匹配对于提高H2S去除率及节能降耗十分重要.     

脉冲电晕法治理甲苯废气实验研究

有机废气的污染日益受到重视,现有的控制技术尚不完善。采用脉冲电晕法对去除甲苯模拟废气进行了实验研究,考察了反应器结构、脉冲电压峰值、气体浓度、停留时间和水汽含量等不同因素对去除率的影响。实验结果表明本法能达到较好的去除效果,在线 筒式反应器的最高去除率为35％,在线 板式反应器的最高去除率达81％,反应后的最终产物为CO、CO₂和H₂O。     

非热等离子体结合CuO催化剂或Ca(OH)2吸收剂去除氮氧化物

采用非热等离子体结合催化或现场化学吸收的2种方法来去除气流中的NO_x.结果表明,非热等离子体结合催化,反应器内的CuO催化剂能有效地促进NO的还原反应;相对于催化还原NO而言,脉冲电晕作用下能有效地降低NO催化还原的反应温度.当催化剂为CuO,脉冲电压为18kV,反应温度为200℃,还原剂为1%CO及NO进口浓度为719 mg/m³条件下,NO的去除率达到了100%.非热等离子体结合现场化学吸收方法,是一种在常温下从气流中净化氮氧化物的有效方法,NO的去除率远远高于反应器内没有吸收剂的情况.可以认为反应器内的Ca(OH)₂吸收剂通过与NO的氧化产物NO₂或NO₃的吸收反应促进了NO的去除.当反应器内有Ca(OH)₂吸收剂存在时,在脉冲电压为18kV,O₂浓度为2%及NO进口浓度为1 050 mg/m³条件下,NO的去除率达到了100%.     

介质阻挡放电降解异味物质CS_2研究

采用介质阻挡放电降解二硫化碳(CS2)模拟废气,考察了外加气体空气、氮气(N2)、电源输入功率、初始浓度和停留时间对CS2转化率的影响。结果表明:CS2的去除率呈现空气>N2。在输入功率63 W,停留时间为5.34 s,CS2的初始浓度300 mg/m3,N2氛围下的去除效率为36.9%,而空气氛围下的去除效率可达62.5%。在N2与空气氛围下其产物明显不同,在空气氛围下,主要产物为SO2、COS、CO和CO2;而在N2氛围下其主要产物为大量单质硫、少量CO与CO2。对DBD降解CS2的机理分析表明,在N2条件下主要是高能电子与紫外光的作用;而在有空气条件下,O2的存在促进了CS2的深度氧化。     

光助芬顿反应催化降解气体中甲苯

以甲苯作为挥发性有机污染物(VOCs)的代表,利用连续进气动态实验装置,研究光助芬顿反应降解气体中甲苯的作用.考察了芬顿试剂溶液初始p H、H2O2浓度、Fe2+浓度以及甲苯初始浓度对降解甲苯的影响,并利用在线质谱和色谱对产物进行了定性、定量分析.结果表明,紫外光照加快了羟基自由基的生成,显著提高了气体中甲苯的去除率;p H=3.0、H2O2浓度为20 mmol·L-1、Fe2+浓度为0.3 mmol·L-1的条件下,甲苯去除率最高;当甲苯初始浓度为260 mg·m-3时,去除率能够达到98%;光助芬顿反应催化降解气体中甲苯实验未检测到CO2之外的中间产物,CO2产率分析表明去除的甲苯全部转化为CO2.     

烟气冷凝过程中雾化碱性浆滴脱硫实验研究

简要分析了雾化Ca(OH) 2 浆滴对SO2 气体的吸收过程。在竖直单管冷凝换热器内利用喷入雾化碱性浆滴,研究了影响SO2 气体吸收的主要因素,Ca S值、反应器入口SO2 浓度、雾化空气量、烟气进口温度、烟气雷诺数都会影响对SO2 气体的吸收效果。实验表明,雾化碱性浆滴强化了烟气冷凝脱硫效果。     

脉冲电晕放电降解水溶液中甲苯实验研究

采用针-板式脉冲电晕反应器对水溶液中甲苯的去除效果进行了实验研究.反应器为Φ90 mm×50 mm圆筒结构,反应器顶部均匀布有不锈钢针放电正极,反应器底部装有板接地电极.反应器上部空间为气体.放电针头与液面的距离为18 mm.实验结果表明水溶液中甲苯的去除率随脉冲峰值电压升高而增大;实验发现在气相为氩气氛围下甲苯的去除效果要好于在氮气和空气氛围下.放置一段时间达到气液平衡后再进行电晕放电,有利于提高甲苯的去除效率.对反应后的水溶液进行测定,检测到有苯甲醛等有机物生成,在水面上方的气体中检测到了CO和CO2的生成.     

A new semi-dry desulfurization process using a powder-particle spouted bed

A new semi-dry desulfurization process was tested in this study. The process uses the so-called powder-particle spouted bed (PPSB) as the reactor in which coarse medium particles, usually silica sand of several hundred micrometers in size, are fluidized with hot flue gas. A slurry of fine SO_x sorbent, such as slaked lime or other alkaline powder, is continuously supplied into the bed of coarse particles. As a consequence, both the desulfurization reaction and slurry drying take place simultaneously in the single reactor. By using a model flue gas, SO₂–air, and the sorbent Ca(OH)₂ in a laboratory-scale reactor, the removal efficiency of this process was examined with respect to major operating parameters in this study. It was demonstrated that SO₂ removal in excess of 95% can be achieved at Ca/S=1.2, while spent sorbent appears in the form of dry powder. The optimal temperature of flue gas treated with this technique was shown to be approximately 420 K. In comparison with wet desulfurization scrubbers, this PPSB semi-dry process appears to have lower cost, less complicated configuration and simpler disposal of used sorbent.     

Simultaneous removal of SO2 and NO using a spray dryer absorption (SDA) method combined with O3 oxidation for sintering/pelleting flue gas

Based on the demand of sintering/pelleting flue gas ultra-low emission, a semi-dry method using a spray dryer absorber (SDA) combined with O₃ oxidation was proposed for simultaneous removal of SO₂ and NO. Effects of O₃ injection site, O₃/NO molar ratio, and spray tower temperature on the removal efficiencies were investigated. It was revealed that both desulfurization and denitrification efficiencies could reach to 85% under the conditions of setting O₃ injection site inside of tower, O₃/NO molar ratio 1.8, spray tower temperature 85°C, Ca/(S + 2 N) molar ratio 2.5 and slurry flow rate 300 mL/hr. CaSO₃/Ca(OH)₂ mixture slurry was used as absorbent to simulate operating conditions in iron and steel industry. The result shows that the addition of CaSO₃ weakens both removal efficiencies. In addition, the reaction mechanism of simultaneous removal of SO₂ and NO using SDA combined with O₃ oxidation was proposed.     

光助-二茂铁/H2O2非均相体系降解磺胺二甲基嘧啶

抗生素在废水和地表水中经常检出,因其可诱导细菌菌群的抗药性而备受关注,因而亟需发展新型高效的抗生素去除技术.本研究构建了基于二茂铁(Fc)的光助非均相氧化体系,并选取水体中广泛检出的磺胺二甲基嘧啶(SMZ)为模型化合物,研究了SMZ在该体系中的降解动力学、转化途径和产物.结果表明,相对于Fc、Fc+UV、H_2O_2、H_2O_2+UV、Fc+H_2O_2体系,SMZ在Fc+H_2O_2+UV体系中呈现更好的降解效率.自由基淬灭实验证实·OH是Fc+H_2O_2+UV体系中决定SMZ降解的最主要活性物种.电子自旋共振实验发现Fc+H_2O_2+UV体系中产生了超氧自由基阴离子,说明Fc在光照条件下可产生电子. H_2O_2接受电子后歧化产生·OH进而促进SMZ降解.采用轨道离子阱高分辨质谱对SMZ在Fc+H_2O_2+UV体系中的降解产物进行了鉴定,发现有SMZ的羟基化、脱SO_2和C—S、S—N及N—C键断裂的产物形成.水中常见溶解性组分,如DOM、Cl~-及Br~-,可淬灭·OH而抑制SMZ降解,但离子强度对SMZ在Fc+H_2O_2+UV体系中的降解无显著影响,说明该技术对于含有高盐度抗生素废水的处理仍具有较好的效果.     

放射示踪法研究O2存在时14CS2与OH的光化学反应

用放射示踪法研究~(14)CS_2和OH的光化学反应,指出氧对反应有促进作用,在反应体系中(~(14)CS_2-H_2O_2-C_3H_8-N_2-O_2)主要产物为O~(14)CS,~(14)CO及少量~(14)CO_2。O~(14)CS和~(14)CO有相似的动力学曲线,~(14)CO_2则是另一种情况。总反应速率常数随氧压增加而增大,在氧压为33330Pa时,~(14)CS_2消失的总速率常数可高达3.4×10~(-12)cm~3mol~(-1)S~(-1)。在实验中观察到~(14)CS_2能在室温下转变为~(14)CO_2的现象。讨论了光化学反应的历程。     

Experimental study of NO2 reduction in N2/Ar and O2/Ar mixtures by pulsed corona discharge

Non-thermal plasma technology has been regarded as a promising alternative technology for NOx removal. The understanding of NO2 reduction characteristics is extremely important since NO2 reduction could lower the total NO oxidation rate in the plasma atmosphere. In this study, NO2 reduction was experimentally investigated using a non-thermal plasma reactor driven by a pulsed power supply for different simulated gas compositions and operating parameters. The NO2 reduction was promoted by increasing the specific energy density （SED）, and the highest conversion rates were 33.7%, 42.1% and 25.7% for Ar, N2/Ar and O2/Ar, respectively. For a given SED, the NO2 conversion rate had the order N2/Ar 〉 Ar 〉 02/Ar. The highest energy yield of 3.31 g/kWh was obtained in N2/Ar plasma and decreased with increasing SED; the same trends were also found in the other two gas compositions. The conversion rate decreased with increasing initial NO2 concentration. Furthermore, the presence of N2 or O2 led to different reaction pathways for NO2 conversion due to the formation of different dominating reactive radicals.     

CO2 reaction with Ca(OH)2 during SO2 removal with convective pass sorbent injection and high temperature filtration

The Kyoto Protocol calls for greenhouse gas emission reductions which could affect the use of coal for producing electricity. Carbon credits are being explored as a method for countries to meet their reduction commitments. Carbon dioxide removal in flue gas desulfurization (FGD) systems should be considered if and when the concept of carbon credits are implemented. This paper addresses the factors affecting sulfur dioxide removal, including the reaction of carbon dioxide, occurring during convective pass sorbent injection with high temperature filtration for a typical coal-fired power plant. Significant carbonation is found to occur, and the levels are found to depend on injection/filtration temperatures and the residence time on the filter. Ca/S stoichiometry during sorbent injection is found to affect not only the sorbent conversions in the convective pass sorbent injection stage but also the final sorbent conversions in the filtration stage. Even though high sorbent carbonation hinders the sorbent utilization for SO₂ removal, slight alterations in CO₂ concentration are found to have no significant effects on the SO₂ removal of the process.     

废茶活性炭脱硫脱硝性能的应用研究

为探讨废茶活性炭对于SO2和NO脱除作用的制约因素,分别考察了材料孔径结构、石墨化程度及表面结构对其脱硫脱硝性能的影响,同时研究了其吸附机制及动力学过程.结果表明,较高的石墨化程度是影响材料脱硫性能的主要因素,微孔径较小且含氮碱性基团较高时有利于SO2的脱除;发达的中孔结构是制约NO脱除效率的关键因素,含氮碱性基团对NO的脱除具有一定的促进作用;烟气中SO2和NO共存时,材料的脱硫脱硝性能均有所降低,氧气和水蒸气的加入能够改善其脱硫脱硝效率;废茶活性炭在无水环境下对于SO2和NO的吸附作用均以物理吸附为主,水蒸气的存在促进了材料对SO2的化学吸附;通过动力学模型的拟合发现,Bangham吸附模型能够很好地描述材料脱硫脱硝的动力学过程,其R2均高于0.989,材料对于SO2和NO的吸附速率常数均随氧气和水蒸气的加入而减小.